NO sound on a clean install of windows 7 on a HP Compaq Lap top VR5207NR

Similar Questions

• No sound on A new installation of windows 7 on a Hp Compaq Lap top VR5207NR

  High definition Audio Device ha an Erreur10, ios, there is no driver not installed for this device, is there a work around available to get to my sound work?

  Hello:

  Try to manually install the driver Audio XP as follows...

  Download and run this driver.  If automatic installation Gets the noise at work, very well.  If it isn't...

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-42513-1&cc=us&DLC=en&LC=en&OS=228&product=3197924&sw_lang=

  Go to Device Manager and click on the multimedia Audio Controller needing drivers.  Click the driver tab.  Click on set to update driver.  Select her browse my computer for driver software and browse the driver folder that was created when you ran the file.

  This file will be located in C:\SWSetup\sp33443.  Make sure that the include subfolders is selected and see if the pilot goes like this.

• I want to do a clean install of windows xp on a hp compaq nx6125 but do not all disks with the laptop but I still have the original windows sticker on the bottom.

  I need to reinstall xp on my nx6125

  I want to do a clean install of windows xp on a hp compaq nx6125 but do not all disks with the laptop but I still have the original windows sticker on the bottom. is this possible or do I have to buy another drive xp and sticker

  Hello

  Yes, you can use this COST to install Windows XP. However, you must have Windows XP.
   
  If you face any problem regarding the installation of Windows XP.
  You can contact our Windows activation service.
  Here is the link:
  http://support.Microsoft.com/kb/950929 

• HP Pavilion - 15-p264na: audio beats does not open after a clean install of windows 8.1

  Hello

  After a clean install of windows 8.1 the audio beats does not open.

  It appears in the control, but when I click on it nothing happens.

  I have sound, and everything seems to work ok, but I'm curious to know what happened.

  When I go to Device Manager and select audio, video controllers and game, there are 2 features 1 is AMD high definition audio and the other just says high definition audio device.both drivers are up-to-date.

  I look through the forums CIHI and I tried some of the links for the drivers of the itd, but they will not install.

  Any help would be appreciated

  Hello

  Download and reinstall the Realtek HD Audio software at the following link.

  http://ftp.HP.com/pub/SoftPaq/sp69001-69500/sp69164.exe

  When the installation is complete, restart the laptop.

  Kind regards

  DP - K

• Portege Z830 - on a clean install of windows access keys

  What do I need to work the KEYS FN on a clean install of Windows?

  I have a Toshiba Portege Z830, width window 8.1 Professional (he cams 7 width windows).

  The first time I installed windows 8, I'm doing the hotkey working width drivers Toshiba a upgrade of windows 8.
  But now, after a new installation, it does not work.

  Some keys work, such as FN + 3 or 4 for the sound. But I think that it is a feature of windows. I need the combination of brightness FN + F6 or F7, and they do not work.

  What should I install? I read that I have to install the driver of Toshiba value added package system, but it does not work. There is also a utillity called Toshiba function key.

  What should I install?

  Thanks ;)

  *@Infocomit*

  Don t be angry with me, but you're wrong. Sometimes it s advisable to check some things twice.
  Driver Toshiba UE page provides details and description on the drivers and utilities.
  If you need to get the details about the unique software, click on the red arrow in the Details column.

  By the way: it's community of users.

• clean install of windows XP to input signal out of range

  Hi I recently took my old pc xp out of the dusty closet.
  I discovered that the operating system has been corrupted then decided to do a clean install of windows xp.
  However after that it says press any key to boot from the disk and I press a button, then it went to a screen blank and says on the monitor says "Input Signal out of range at 1280 x 1024 60hrz. change."
  I also did a reset factory monitor and hooked up the old pc to the tv.
  So I would like to know how to solve the problem, any help would be much appreciated.

  Hello

  First you using a discrete graphics card or graphics are integrated with the motherboard? Change BIOS battery (or whatever it is in the BIOS change to any method) will not change anything to do with a graphics card discrete and not likley to do much for either integrated graphics card.

  What it sounds like to me, is that the key to the race to start from the CD is not recognized and that Windows is actually booting from the hard drive with a resolution taken not supported by your monitor. But, being not there, I can't be sure of this so here are some ideas of diagnostic.

  Start the PC without the CD inserted, do you have the same problem?

  The keyboard is correctly connected?

  If a PS/2 keyboard is it plugged into the outlet of PS/2 mouse by mistake (keyboard taken are normally purple, green mouse normally Sockets)?

  Is the keyboard PS/2 or USB? You can try another keyboard ideally with the other type of interface?

  You can get in the setup of the BIOS by the appropriate key combination (usually F2 or DEL but I saw others also, look for the message at startup upwards)? If you can not it would indicate a keyboard problem.

  If you can remove the keyboard as a problem, I would return to my original question on a discrete graphics card. If there is a discreet graphics card, the motherboard is also a graphic? If this is the case, remove the discrete card and try windows set up again. Or even try installing windows with a spare graphics card if you can get your hands on one. Turn off the computer and unplug it from the socket before to remove/replace all internal components.

  Finally, what of the installation CD? Is this the one supplied with the PC? It is the recovery of the real manufacturer CD or CD from Microsoft genuine?

  Tricky

• Question seeks to clean install 10 Windows on the drive of the merger. El Capitan.

  Problem: try a clean install of Windows 10 via the Boot Camp Assistant on an iMac 27 inches (Late2013) with 10.11.4 installs hours (more than 8 hours) and then failed to install Boot Camp updates. Essentially installation take much long than normal and cannot install updates of the Apple software or create normally start Windows Boot Camp 10.

  Background: After problems of slowing down after upgrading to 10.11.4 (with improved Bootcamp Windows 10) who had previously worked fine for 10 months, to the point of a start of OS X time, I decided to do a clean install of my iMac with Fusion 3 to disk.

  As I was unable to remove the partition from Boot Camp through BCA because of his holding always at the same load, I used Internet recovery and reset the Fusion drive. This then required me to repair the partition of Fusion by car through THE "fix" option which seems to work very well. And reinstalled OS X 10.11.4 which works fine now (delays etc..)

  Try using BCA to create a new partition Boot Camp and a clean Windows 10 install after downloading an image of disk W10 directly from Microsoft (Win10_1511_1_English_x64), BCA by downloading software updates and by selecting the desired partition, it began to restart and initialize the installation. However the whole process has been very slow, each step takes much longer than usual, to progress. Leave for hours rest a blank screen or with a circle of rotation.

  I tried with another stick USB 3 and also a USB 2 stick, but none has made a difference.

  In the last attempt, I left running overnight and after 8-9 hours, he finally reaches the top of desktop Windows 10 and the update of Apple Bootcamp starts to load updates. However, he just hung and even after 2 hours, nothing was. Reboot and try once again has been the same.

  After that I tried to create a Windows Installer via BCA 8.0 however it gives just a TPG error when you try to select the drive (due to el Capitan I guess?)

  After four days of efforts, I'm a loser on how to get the Windows 10 on the Boot Camp partition. I can't even install W8 and upgrade due to the error of TPG.

  Any help or suggestions how to proceed with the diagnostic / resolution of the problem would be appreciated.

  Details:

  System: iMac (27 inch, end of 2013), 3.4 GHz Intel Core i5, 16 GB 1600 MHz DDR3, NVIDIA GeForce GTX 780 M 4096 MB, OS X 10.11.4

  • Nothing other than the keyboard and mouse attached via the USB ports, as well as the key USB of BCA. No other attached devices.
  • Reset memory NVRAM, SMC and ran more than once disk utility. No problem not reported.  Ran NVRAM reset before each attempt.
  • At ran EtreCheck report which seemed OK.
  • Verification of diagnosis ran who is childless.

  A detail I noticed after the merger by car there are now two Macintosh HD images when you use boot option. One previously. Are named "Macintosh HD" and "Macintosh HD2". I remember being Yosemite simultaneously in three, but which has been fixed in an update.

  In addition, it seems that no recovery partition. Cmd + R lance Internet recovery.

  Distill the results (the Boot Camp partition removed):

  / dev/disk0 (internal, physical):

  #: NAME SIZE TYPE IDENTIFIER

  0: GUID_partition_scheme * GB 121,3 disk0

  1: disk0s1 EFI EFI 209.7 MB

  2: Apple_CoreStorage GB internal drive 121.0 disk0s2

  3: disk0s3 Apple_Boot Boot OS X 134,2 MB

  / dev/disk2 (internal, physical):

  #: NAME SIZE TYPE IDENTIFIER

  0: GUID_partition_scheme * 3.0 to disk2

  1: disk2s1 NO NAME 209.7 MB EFI

  2: disk2s2 Apple_CoreStorage TB 3.0 drive internal

  3: disk2s4 Apple_Boot Boot OS X 134,2 MB

  / dev/disk3 (internal, virtual):

  #: NAME SIZE TYPE IDENTIFIER

  0: Apple_HFS Macintosh HD + 3.1 TB disk3

  Logical volume on disk0s2, disk2s2

  7BE1F343-ACBE-4144-BF86-C838BE1E49D4

  Fusion unencrypted drive

  iMac - simon: ~ list of cs simon$ diskutil

  CoreStorage groups of logical volumes (1 found)

  |

  + Logical Volume - Group CA0B8D0A-6315-4E85-B313-52AB509473F2

  =========================================================

  Name: Internal drive

  Status: online

  Dimensions: 3121237860352 B (3.1 TB)

  Free space: 0 (0 B) B

  |

  +-Physical volume 5E75EE74-EE1F-4FCB-A0C5-9ED5517FEB93

  |   ----------------------------------------------------

  |   Index: 0

  |   Disc: disk0s2

  |   Status: online

  |   Dimensions: 120988852224 B (121.0 GB)

  |

  +-Physical volume 91D639D6-634E-47C1-AFE5-616CE12E71E0

  |   ----------------------------------------------------

  |   Index: 1

  |   Disc: disk2s2

  |   Status: online

  |   Dimensions: 3000249008128 B (3.0 to)

  |

  +--> Logical volume family EE9934AC-F3CB-4101-ADB6-576F4371B4B9

  ----------------------------------------------------------

  Encryption type: no

  |

  +--> Logical volume 7BE1F343-ACBE-4144-BF86-C838BE1E49D4

  ---------------------------------------------------

  Disc: disk3

  Status: online

  Size (Total): 3106705375232 B (3.1 TB)

  Reversible: no

  Name: Macintosh HD

  Volume name: Macintosh HD

  Content indicator: Apple_HFS

  LVG Type: Fusion, sparse

  Summary:

  Q1: Should it take 4 + hours to install Windows 10 via BCA?

  Q2: Al must ultimately be so slow when initially W10 desktop?

  Q3; What I do once I arrive at the office of W10 but it automatically updates the graphics driver as BC update is simply suspended for centuries and get a working driver to restart at least W10?

  Q4: is there a problem with the disk HARD the Drive of Fusion that is causing all this delay and slow install / boot? ON the clean install OS X 10.11.4 it is back to be fast as usual and all tests show things are OK but W10 goes on the part of the HARD drive. No way to verify this beyond diagnosis or Etrecheck?

  Q5: Y at - it no problem with the GPT / MBR that may be causing the delay etc. ?

  Q6: How can I use my existing WindowsImageBackup backup from the previous W10 with the BCA install usb drive or how to create a USB stick otherwise recovery disk with my other single Mac have W7?

  Q7: How can I install W8 as I once did on Yosemite, via el Capitan without a mistake to TPG on selection of disc?

  Details:

  Day 5. Attempt at 6.

  Partition Boot Camp delete and try again install via BCA. First question, is that when the startup it goes to a blank black screen. For a time nothing left. Reset then using alt to select windows training results in almost instantaneous startup of the BCA message created and the beginning of the installation.

  4 1/2 hours from start of Windows 10 initial signature window.

  Then the second question. One to reach the Boot Camp update Office tries to start and install the drivers. Allows you to "list files...". "stage then sits at the bar about 5% green for 1 to 2 hours and does nothing. All actions in the Office of the W10 takes ages.

  In the meantime, auto update of the W10 appears a message saying that the updated graphics drivers as one of the few messages or actions during this period. Looks like Nvidia install with the entire package of experience (unwanted) etc. and very probably not the correct gpu driver.

  Finally deciding to cancel the installation of BC by killing the Setup.exe process. Then copy Boot camp install files on the desktop. Lasts 30 minutes to copy. Run again and this time, although taking 15-20 minutes to download and install later with the success message.

  Check the graphic driver it shows a yellow exclamation mark, so the following Microsoft instructions I use the uninstall option via the device and then Manager (slowly) come on board to load and download the latest Nvidia driver on their site for the GTX 780 M for 64-bit W10 etc. The same thing that I had used previously. Slow with running the Nvidia Setup program again, but eventually it works only to say that he could not install as unrecognized graphics device...

  He ends up with Microsoft PnP driver so it's at least sufficient start and run it again BC of the figure updates as all other drivers have been installed. To restart, but I get an error of K-Mode that is most likely related to this driver graphic and not possible to start in the new W10 Boot Camp partition after 7 hours.

  I have a picture of W10 backup recovery (WindowsImageBackup) I've had in a few weeks, but it will not install bet for the installed W10. I try with the ACO created the USB windows but can't seem to get a way to get into recovery mode and to get the menu to install it. I don't have a way to create a USB W10 recovery key now because my other Mac has just installed W7.

  Finally I tried to count a reset of the Recovery boot up option but it seems that it will take longer to start.

  I also went to the recovery and selected Boot Mode safe, but it opens on an empty black window and he's here doing nothing.

  Looks like I'll have to restart on via BCA and reinstall and try and solve the problem of graphics in order to install driver updates from BC and restart to W10 and hope that with the drivers, it returns to the operation and the normal starting time. Then update the gpu driver.

  I used and installed Boot Camp several times with over the years including previously an upgrade of W8.1 > W10 I used for over 6 months without problem. I've never known these installation very long or ice once in Windows even for the initial start upward.

  For any help or suggestion would be appreciated, and this seemingly simple process has now expanded to five days.

• error message iTunes displays locked drive, itl locked files, or do not have administrative privileges on the PC after a clean install of Windows 10

  Yesterday I did a clean install of Windows 10 on my PC with a backup of the hard disk external. I downloaded iTunes, but get an error message that the drive is locked, the .itl files are locked, or I don't have administrative rights to these files. I deleted and reinstalled the PCI DSS several times correctly in the PCI slot hoping that would be a solution, but to no avail. I am the only user on this computer and do not have administrative rights. Any help you can offer will be appreciated. Thank you

  This can help (from turingtest2):

  Fix iTunes for Windows security permissions

• Clean install of Windows 7 on Satellite L655

  I have a Satellite L655 and replace the HDD with a SSD (2 sheets) system (more small capacity, 1 partition). I also want to do a clean install of Windows 7.

  I'll be able to use the recovery disc for this? If so, will I have to reactivate? Thank you.

  > I'll be able to use the recovery disc for this? If so, will I have to reactivate? Thank you.

  What exactly do you want: clean windows installation or by using the disk Toshiba recover?

  I mean own installation only the Windows operating system using the Microsoft Win 7 disc.
  This installation requires a valid serial key.

  But using the Toshiba recovery disc requires no any key since the BONES of the window is already enabled on this drive.

• Satellite P305-S8820 - FN key not working after a clean install of Windows 7

  Hello

  I have a Toshiba Satellite P305-S8820. I recently did a clean install of Windows 7. I loaded the value Toshiba driver pack and the trackpad driver but still cannot get the trackpad or press FN to work.

  Any ideas?

  Hi taxwiz,.

  I think that the forum already contains hundreds of discussions about this so why you n t use the forum search?

  Anyway, you need the latest version of Toshiba Value added Package and utility Support Flash Cards.
  Try to also restart Toshiba Flash Cards (start > all programs > Toshiba) and repeatedly press the FN keys.

• Clean install of Windows 8

  I want HP DV6t. There are some informal activities past in my laptop. So I just want to do a clean install of Windows 8. I don't want to delete my other files on the disc. I just want to reinstall windows 8. I have the recovery disk. What are the steps to follow... ? Someone help

  A clean install of Windows 8 will be erase your other files by definition as recovery disks. Fortunately, Windows 8 has a few new options of Maintenance not seen in earlier versions. You can try a BONE 'refresh' that will install the new system of Windows 8 files without disturbing your data or settings.

  http://www.PCMag.com/Article2/0, 2817,2410848,00.asp

  You want to back up your important files before there is a small chance that it can go wrong.

• I would do a clean install of windows 7 Professional 64 bit in my hp probook 4540 s

  I would like to do a clean install of windows 7 Professional 64-bit in my hp probook 4540s.after install exactly what are the necessary to install drivers and whence? Thank you

  Hello:

  Here is the link to the support page and drivers for your laptop.

  http://h20000.www2.HP.com/bizsupport/TechSupport/SoftwareIndex.jsp?lang=en&cc=us&prodNameId=5229457&prodTypeId=321957&prodSeriesId=5229455&swLang=13&TaskID=135&swEnvOID=4059

  Now, we can tell you exactly what drivers to install the adapter wireless because he could be one of several models installed in your laptop.

  You must install the following drivers in this order.

  Chipset: Installation and reboot

  http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=321957&prodSeriesId=5229455&prodNameId=5229457&swEnvOID=4059&swLang=13&mode=2&taskId=135&swItem=ob-105389-1

  Video: How to know what graphics card is in your notebook (AMD or Intel). Install and reboot.

  Audio: Installation and reboot

  http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=321957&prodSeriesId=5229455&prodNameId=5229457&swEnvOID=4059&swLang=13&mode=2&taskId=135&swItem=ob-106423-1

  Wired network:

  http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=321957&prodSeriesId=5229455&prodNameId=5229457&swEnvOID=4059&swLang=13&mode=2&taskId=135&swItem=ob-105307-1

  Then these are the drivers, I know that you will need:

  http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=321957&prodSeriesId=5229455&prodNameId=5229457&swEnvOID=4059&swLang=13&mode=2&taskId=135&swItem=ob-105298-1

  http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=321957&prodSeriesId=5229455&prodNameId=5229457&swEnvOID=4059&swLang=13&mode=2&taskId=135&swItem=ob-104954-1

  http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=321957&prodSeriesId=5229455&prodNameId=5229457&swEnvOID=4059&swLang=13&mode=2&taskId=135&swItem=ob-104949-1

  Paul

• Laptop HP 15-R204NE: clean install of Windows 10

  Hello

  I'm ready to do a clean install of Windows 10 but the only thing that worried me are the drivers provided factory installed with my laptop, it was initially delivered with Windows 64 - bit of 8.1. I don't want to lose one that I have no idea how or where I'm going to do if I lose everything. If someone has a way to understand this help is very much appreciated.

  Kind regards.

  Hello Zarakkhan ;
  
  I read your post on the new install of drivers of Win10 and wanted to help.

  As to the first, the upgrade of active Win10 through something known as right digital, install some sense, when you perform an upgrade on the spot on an existing Win7/8/8.1, upgrade reuses the existing product key for activation.  After you confirm that the machine is turned on, you can THEN do a clean install on the same machine.  IF you do a clean install without activating the first, you will not activate your copy of Win10.

  That said, MS released earlier to a new update to Win10 and (allegedly), you should be able to do a clean install with NEW media made from multimedia authoring tool and have it activate using your product key of Win8.1.  But, I haven't read anyone done this yet, is just a rumor at this point.

  As for save the drivers, there's a product excellent freeware called Driver Backup.  After you download and install it, you can then save out all your current drivers on a USB key.  This will make reinstall them later a simple process. I know it works because I use this product myself.

  Good luck
  
  I'm a volunteer and I do not work for, or represent, HP.
  ========================================================================
  If you feel that my suggestions helped you, please click on the thumbs-up symbol to say thank you!
  
  If they helped to solve your problem, please click 'Accept as Solution' to help others find similar information.

• Pavilion 14 G6S71UA #ABA: I'll always be able to use the pre-loaded software HP products if I do a clean install of Windows 10?

  I have a laptop 14 flag that came with Windows 8.1 - 64 Home, and I have upgraded to Windows Home 10-64. The upgrade went very wrong, but I would use Win 10 if possible. Microsoft recommends that I have to do a clean install of Windows 10, which will require you to reinstall all my programs MANY. They cannot tell me, however, if I'll still be able to use some of the applications delivered HP pre-loaded on my machine and that I find very useful - even if I am out of warranty. For example, I use HP Support Assistant updates the driver, and I found that HP DriveGuard works really well!

  I'll always be able to download all of these products and hence? I'll be able to get them on the page of the drivers for my laptop? If I can't, I'll probably have to settle for return to Windows 8.1.

  Thank you.

  Because the rep on the Microsoft forum did not answer my questions, today I called the support of Microsoft Windows 10 phone number. After that the rep is lost another hour of time my (and their) me browsing to enter SafeMode via several methods, everything I told him that I had already tried. the representative suggested that customizations of account that I had applied could be the cause of the distress.

  She also informed me that, for security reasons, Windows 10 no longer allows connectivity Mode Wireless safe; Although, if your PC is physically connected to the modem/router, you should be able to enter in IE (and maybe even in Edge) in Safe Mode.

  So I added a new local administrator account (that said, I log in with a password and not with one account Microsoft.), to be used only for safe mode and left all its parameters to the default values for Microsoft. And it worked! When connected to my router, I could get in Mode safe mode with internet connectivity via IE! Thanks to this rep, I finally have success.

• HP MIni 210-2145 DX: clean install of Windows 7, now I can't find the wireless drivers that work.

  I have a HP mini 210-2145 DX.  I recently had to do a clean install of Windows Ultimate edition.  Now, I can get a wireless connection because I can't find the right drivers on the HP site.  I tried 12 + drivers that I downloaded.  They all seem to be for 32 bits, and it's 64-bit.

  Can someone please help me find the right wireless drivers to install?  Thank you.

  Try this different file and see if it works automatically and installs the driver.

  File name: sp57965.exe

  There was also support for the hardware ID you have posted.

  I have no problem downloading the file, or by using 7 - zip to extract the exe file downloaded to a folder that you can browse from the network controller to install the drivers.

  Unfortunately, I can't help you with the problem if the new file does not work.