No sound on external display connected by HDMI win7 premium 64-bit running Notepad

Similar Questions

• Bad resolution of Qosmio G30 - external display via the HDMI connection-

  Hello! This problem makes me crazy, please help if you can...

  I just bought a G30-102 and I am trying to use it with an external display via the HDMI connection. The problem I have is that the native resolution of 1920 x 1200 cut the edges of the screen and the quality looks terrible - its almost as if the entire screen is enlarged. I tried with a BenQ FP241wz initially (1080i is 1920 x 1200) and the Toshiba helpline could not find a solution either - even after painfully reinstall all the drivers, etc..

  Its been going on for so long, I thought I'd try it out with my HDTV instead, just to be sure it wasn't a monitor problem. So I tried with my Toshiba 32WLT66 - and come to find that it has exactly the same problem.

  All the display settings appear to be correct and the G30 is convinced that the result is correct, so I have now it is - don't you think not that this is a problem with my HDMI port?

  Please help, I'm a designer, and it is essential that I use the machine on a large screen. If it is a hardware of the G30 problem, I need to talk to Toshiba immediately replace or fixing.

  Hello

  I tested the Qosmio G30 (HD-DVD) with my LCD TV using a HDMI cable. Everything worked perfectly. As a first step, I put 1080i value in the settings of the BIOS and after following the instructions in the HDDVDGuide document under http://support.toshiba-tro.de/kb0/TSB6A01LH000LR01.htm

• Two external displays connected to my dock and my ThinkPad T450

  I have two external displays connected to my dock and my ThinkPad T450.
  Everything works fine, when suddenly the monitor LEN LT2223pwC (using DP cable) goes into energy saving mode during use and there is not up to come back/wake, only to turn it off and back on
  This Setup worked very well with my office. For some reason any the monitor does not receive the signal from the laptop / docking station.

  I got a new docking station and solved the problem. Thank you

• Want TO TS15j021 when an external monitor connect through HDMI is NO sound through speakers.

  I have attached a Samsung LED 27 "external display on my laptop via HDMI port and install double screen, NO sound/audio to come through the laptop speakers. However, when I select just the screen of the laptop, the sound comes back and works very well. Any suggestions would be much appreicated.

  "Accept as Solution" Thank you for your help. It worked a treat.

• Remote Desktop connection: Windows 7 Home Premium 64-bit connects to the computer of Windows XP VPN

  Hi all

  I am trying to establish remote desktop TO my new laptop (Windows 7 Home Premium 64-bit) on my computer (Windows XP) work via a VPN. The VPN Client connects to my network to work with no problems, but when I try to use the remote desktop connection I get an error message:

  Remote Desktop cannot connect to the remote computer to one of the following reasons:

  (1) remote access to the server is not enabled

  (2) the remote computer is disabled

  (3) the remote computer is not available on the network

  Make sure that the remote computer is on and connected to the network, and remote access is enabled.

  Items 1-3 are working well, so I guess that the problem is caused by another issue?
  I'd appreciate any help.
  Thank you
  Lou

  Thanks for your response Al. To answer your qus:

  (1) cisco VPN Client for 64 - bit.

  (2) I don't know how to ping through the VPN tunnel - I don't see this option, anywhere in the Cisco customer (I'm not a professional, just a user)

  (3) Yes. Also, I can connect to the host PC via my old laptop XP (xp) of fine House, just not my new laptop (Windows 7 Home Premium) so the problem must be with my new laptop rather than at the end of the host PC.

  After that you connect through the VPN tunnel open a command window, IE. go in Start > run , then type cmdand type ping DRC-hostname or IP-address-DRC ping.

  Examples:

  Ping lou - pc

  ping 192.168.1.25

  FWIW, I have a desktop computer home wireless Windows 7 Home Premium SP1 64 bit on my LAN that connects fine to a XP Pro SP3 32-bit Wired test machine using [DRC] remote desktop. Now XP Pro SP3 DRC test machine is configured for a static IP address and I have manually configured the network mask, gateway, DNS resolves and made sure that NetBIOS over TCP/IP is enabled in the properties of the NETWORK Ethernet card on the test computer.

  Just for fun, I checked the hashes of file for the file mstsc.exe on the Win 7 Home Premium 64-bit machine and a machine Win 7 Home Premium 32 bit I have and hashes were a bit different as the size of the files. The versions of the files are the same though. I assume that the difference is because we're 64-bit to 32...

• MacBook pro screen flashing external display connection

  Whenever I connect a display remotely on DVI (tried both Apple DVI-> Adapter Mini DisplayPort customized DVI-> HDMI adapter), my Macbook pro display blinks for a long time, like 1-2 minutes before you succeed. This does not happen with VGA (I tried Apple VGA-> Mini DisplayPort adapter). He is shown here:

  https://www.YouTube.com/watch?v=dLmI82DDvXw

  It's annoying as *. For example: whenever I visit the coffee machine or the bathroom, I have to wait 1-2 minutes until I can get back to work, because the screen was turned off until I can come back. And don't suggest me to extend the period of closure, which is not a viable solution. It happens every morning so when I get to work and turn on the computer.

  Any help would be greatly appreciated!

  See you soon

  Hi ColonelKermit,

  I understand that you have a problem with your screen when attaching it to an external monitor. You can try to fix it by resetting your NVRAM memory on your computer, which is explained in the following article:

  How to reset the NVRAM on your Mac - Apple Support

  https://support.Apple.com/en-us/HT204063

  You can also start your computer Safe Mode, which can help to influence the situation:

  Try safe mode if your Mac does not end commissioning - Apple Support

  https://support.Apple.com/en-us/HT201262

  Thanks for being a part of the communities of Apple Support!

• System hangs on the external display connection

  I just bought a MacBook Pro 13 "mid 2012 version because I travel a lot." I do a lot of coding on my main PC. I didn't mind having a smaller screen and the retina no since I had to plug my monitor 27 "HD for the majority of my work. This is the problem...

  Two things happen when I try to connect it via Apple's Thunderbolt at the VGA connector. Or the other

  1. the external screen but the MBP 2012 (1200 x 800) native resolution and I can't change it at all

  or

  2. all of the gray system out and crashes and the second monitor turns off say there is no entry. Then I pressed the power button to turn off completely it.

  Nothing wrong with the display or the adapter I tested them both on another laptop that my wife and my main development office (two PCs). I guess that something is wrong with the MacBook or the underlying software. I'm running El Capitan and the MBP is maxed out in RAM and a 500 GB SSD. I tried a lot of things I've seen online already, but none of them worked. Is this what can I do to get the 2nd screen to work on its 1920 x 1080 resolution?

  Have you tried the PRAM reset?

  How to reset the NVRAM on your Mac - Apple Support

• I can't get sound through tv when connected via HDMI

  I have a HDX 18 and I connected it to my Olevia via the HDMI. I hear no sound on the tv. I used to be able to. What settings should I and how >

  Hey you probably already found a solution to your problem because you posted this comment a long time ago. But incase you don't have. Here's the answer to your problem. I hope it helps.

  • New direct connection between a TV high definition and a graphics card in the computer using a HDMI cable
  1. So that the audio works fine on HDTV, the device must be configured as peripheral by default in the computer Device Manager. To do:
  1. In Windows® XP:
  1. Note! Before you configure the audio device by default, the following Microsoft driver must first be installed: Universal Audio Architecture (UAA) High Definition Audio class driver
  2. After installing the UAA driver, click Start
  3. Select Control Panel
  4. Select sounds, speech and Audio devices
  5. Select sounds and Audio devices
  6. Click the Audio tab
  7. In the first article entitled audio playback, select the device you want to audio out of
  8. Click OK to save your settings
  2. In Windows Vista®:
  1. Right click on the "speaker" icon
  2. Select the device of reading options
  3. Right click on the device you want the audio to the output of
  4. Set as audio device as the default
  5. Click OK to save your settings
  3. In Windows® 7®:
  1. Go to the Start button
  2. Select Control Panel
  3. Select the material and audio
  4. Select sound
  5. Click the Read tab
  6. Select the device you want to audio out of
  7. Click on set as default
  8. Click OK to save your settings

• W520 gets stuck on Thinkpad with a hard drive external display connected

  Hello world

  I just changed from an external hard drive of 500 GB to 3 to one, but if I leave that new connected for starting my computer the computer crashes to the thinkpad logo and launch startup.

  The boot order is set to boot from the internal hard drive before the media CD or USB, so I don't know why it is the way.

  I have no problem with my original external hard drive connected.

  This isn't a huge problem, just a downside I want to turn on my computer, wait 30 seconds, going ' Oh shoot, on the right, "have to disconnect the drive, and then restart.

  Thanks for any help!

  gtlane wrote:

  Hello world

  I just changed from an external hard drive of 500 GB to 3 to one, but if I leave that new connected for starting my computer the computer crashes to the thinkpad logo and launch startup.

  The boot order is set to boot from the internal hard drive before the media CD or USB, so I don't know why it is the way.

  I have no problem with my original external hard drive connected.

  This isn't a huge problem, just a downside I want to turn on my computer, wait 30 seconds, going ' Oh shoot, on the right, "have to disconnect the drive, and then restart.

  Thanks for any help!

  What level of BIOS are you running on the W520 and what external HARD drive brand? BIOS 1.38 was supposed to fix the POST with the 3 TB drive plugged into the USB 3.0 port. Please report back.

• No sound on TV when connected via HDMI

  I guess the title says it all. When I connect my laptop via HDMI to my TV, there is no noise coming from the TV, I have to listen through the laptop speakers.

  My model # is dv6 - 2143ca

  My operating system is Windows 7 - was NOT an upgrade of Vista

  64-bit operating system

  Help, please! Thanks in advance!

  Hello

  Disconnect the laptop from the PC.  Return to the acoustic window.  Left click the ATI HDMI output once to highlight then right click and set it as the default device.  Click on apply to apply the change, close the window and try again to establish the connection.

  Kind regards

  DP - K

• Satellite Pro P100: external display connected to DynaDock uses 800 x 600

  I have a P100 SatPro attached to a monitor external 19 "via a Dynadock.

  By default, whenever I start the laptop the screen resolution 800 x 600.
  I have to manually reset to my desired resolution (1280 x 1024, 32-bit colors).
  If I reboot at any time the resolution then default back to 800 x 600.

  It's driving me crazy! Why won't save the settings? I tried to reinstall the software with no joy.
  Operating system is Windows XP SP2 and I'm a full administrator.

  Any help or ideas appreciated.

  see you soon
  Ian

  Hello

  I m not 100% sure if this might help you, but I noticed a similar problem on the Tecra M4 anchored to the multiple dock Tablet.
  The update of the BIOS helped solve this problem.

  In addition, an update of the graphics card driver would be desirable.

  Good luck

• "There no external display connected.

  This message came suddenly on the screen and won't go away, even if I rebooted several times. It rises on the top of each window, and it is disturbing. What should I do to make it go away?

  Hi JI,.

  Thanks for the reply and sorry to hear about the inconvenience caused.

  This problem may be due to corrupted display drivers.

  I suggest you to uninstall display drivers and restart the computer.

  Please refer to the article that will help you to uninstall devices by using Device Manager:

  https://msdn.Microsoft.com/en-us/library/Windows/hardware/ff553572 (v = vs. 85) .aspx

  Once the drivers are uninstalled, restart the computer and check if that helps.

  Hope this helps, for assistance please answer.

• Pavilion dv6-1053 cl. Some sounds, but not on video. Vista Home Premium 64-bit.

  This had happened in the past and a reboot would be the cure.  Now restart does not clear the problem.

  I checked Windows Update and found two recommended updates related to sound.  Installed both and my problems seem to be resolved.  But came back.  No sound on the videos again.

• Re: Satellite A660-10W - connection external display with HDMI cuts sound on

  When I use an external display via the HDMI, it mutes the sound of the laptop.
  It's OK because the external display has a headphone/speaker output jack.

  However, when I close the external screen (which I use for movies only) and to use the laptop only, the sound is cut all the time that the HDMI cable is connected.

  I can't hear sound - by harman/kardon speakers or headphone - when the HDMI cable is disconnected (if the external display is turned on or off).

  Is there a way to allow me to have the choice and use her laptop - even when the HDMI cable is connected - in order not to keep plugging and plugging on?

  Thank you

  It is clear.
  If the HDMI cable is connected, then the digital output is defined as audio output by default and therefore you do not hear the sound of the internal speakers but on external monitor speakers.

  You need to change the sound settings.

  Go to control panel of-> sound-> reading tab and set the speakers to laptop as default.
  Then you should hear sound from the speakers for laptop!

• MacBook - problems to connect the external display w

  I do a lot of presentations (Keynote) to Mac external displays at events.

  The new MacBook (12 ") is quite often problems, so I have to carry a MacBookAir as back-up in case where.

  Problems can be no image at all, or two images (like 70% Keynote + 30% of office) and with spikes.

  It doesn't matter if I use HDMI or VGA. And Yes, I know how to set the resolution in the workplace sometimes that the problem is solved by adjusting the resolution manually, but then the Macbook can jump to the resolution which does not by itself during the slide show...

  I think that the problem only occurs when I have to go through a device such as a split, or when there is a lot of tech back stage.

  Anyone having problems of this kind with the MacBook?

  Any ideas on what is wrong and how to fix?

  Hello stefanfromingaro,

  The article link below a certain number of troubleshooting steps in details that can help stabilize the output video to your Mac when connected to external displays.

  Get help with graphical problems on external displays connected to your Mac.
  https://support.Apple.com/en-us/HT201177

  All my best.