No Start Menu found after the HP updates

Similar Questions

• Edge 13 - start is not after the BIOS update

  Hello

  I have a Thinkpad Edge 13 0196 - 32G and had problems with the battery capacity. Windows 7 has shown a red cross next to the battery icon, battery lasted very little).

  A representative of the Romanian Lenovo Lenovo Support suggested that I have make a few updates in the following order:

  -last update of the BIOS

  -last Power Manager

  -last power manager driver

  -latest firmware of the battery

  -perform a battery to reset using Power Manager

  I downloaded the above and started the process with update of the BIOS, but during the final phase, if the update, the computer stops suddenly (I wasn't looking at the screen at that moment), and the computer is now * try * to begin with, but it seems not somehow.

  Here's what happens:

  -the Red led lights up every now and then, during short periods of time (~ 1 second)

  -When it turns off, I hear a sound mechanical sorting of the left side of the laptop, I believe it's from the hard drive

  -the process repeats indefinitely

  -I can shut down the computer by pressing the button for a few seconds.

  I'm desperate! How could this have happened?

  Please give me some clue as to how I can start the computer and solve this problem - I have some very important documents on the hard drive.

  Thank you

  Change later [1]: I tried to install the BIOS version is 1.19-1.13(6YET36WW)/1.24-1.13(6ZET37WW)

  (that's what he said when I start the BIOS Setup

  Change later [2]: I read in the file read me the utility to update the BIOS if the computer crashes, you should unplug the power and remove the battery, then put back them and try to start the computer - it worked, and now I'm in the last stages of the above mentioned battery update procedure.

  For those expierencing a battery problem with their ThinkPad Edge 13 with machine type models 0196, 0197, 0492, it would be prudent to first check this firmware for you the battery.

  A few other steps you can take with your machine in addition to those you listed is a discharge of static electricity. Here's how to make the discharge of static electricity:

  • Unplug the power supply
  • Remove the battery
  • Unplug cords or express cards
  • Press the button power 10 times and the 10th press hold for 30 seconds

  In addition, you also meet noise hard drive? If so, can you describe the noise you hear?

• I have CS4 software. When the first time I install, I chose the content of the normal installation. Then I found that there is no photoshop in the start menu. After that, I try to put the disk in the laptop and find that it has Photoshop on

  I have CS4 software. When the first time I install, I chose the content of the normal installation. Then I found that there is no photoshop in the start menu. After that, I try to put the disk in the laptop and find it didn't photoshop on the list "installation."

  Download the files to install cs4 design premium and install ps to use them,

  Available downloadable Setup files:

  • Suites and programs: CC 2014 | CC | CS6 | CS5.5 | CS5 | CS4, CS4 Web Standard | CS3
  • Acrobat: XI, X | 9,8 | 9 standard
  • First Elements: 13 | 12 | 11, 10 | 9, 8, 7 win | 8 mac | 7 mac
  • Photoshop Elements: 13 | 12 | 11, 10 | 9,8,7 win | 8 mac | 7 mac
  • Lightroom: 5.7.1. 5 | 4 | 3
  • Captivate: 8 | 7 | 6 | 5.5, 5
  • Contribute: CS5 | CS4, CS3

  Download and installation help links Adobe

  Help download and installation to Prodesigntools links can be found on the most linked pages.  They are essential; especially steps 1, 2 and 3.  If you click on a link that does not have these listed steps, open a second window by using the link to Lightroom 3 to see these "important Instructions".

• After the last update of Firefox, youtube videos do not play. The answers I've found are not relevant or too complicated.

  After the last update of Firefox, youtube videos do not play. The answers I've found are not relevant or too complicated.

  Hi Cbella, YouTube is generally used with an HTML5 player, who is a player who does not use a plugin video in MP4 format (for example, it does not use the Flash plugin).

  Now, I based this assertion on Windows, Mac may vary.

  Could you do two tests for me?

  Test #1:

  To verify which player you see (which does work), try a right click or Ctrl + click on the YouTube Player and check the "context menu" that rises. If it's the Flash, there will be a menu short, referring to the Flash on the last line. If you do not see that, if you get a regular menu of Firefox, it's probably the HTML5 player.

  Are what player you?

  Test #2:

  If you open the following test page, which videos to play?

  http://www.quirksmode.org/HTML5/tests/video.html

  • The video "H.264/MP4" play?
  • The video "WebM" play?

  Thank you.

  Also, you can check if your Flash plugin is up to date? You can use the site Mozilla Plugin check for this (please ignore the other plug-ins page wants you to update at the moment avoid making the situation more complicated):

  https://www.Mozilla.org/pluginCheck/

• Windows 7 Pro 64-bit not start after the first update.

  Integrated system:

  Motherboard: Version of the BIOS Gigabyte GA-X58A-UD3R revision 2.0: FA

  CPU: Intel Core i7-930

  Memory: 6 GB Corsair PC3-12800 DDR3 Triple channel

  HD: Western Digital Black 500 GB SATA 3 Gb/s

  Water cooler: Corsair H50

  The operating system has been installed and running perfect. Readers for the mobo has been installed and and all is well. I can see everything on my computer, network, disks, programs, Device Manager and etc.

  First update for the system, only the important updates were downloaded and after the reboot, the system will not start. The system to start repairing the system but found no problem and restart again and return to the screen of system repair.

  The operating system has been installed 5 times and I had the same problem after the first update, the system unbootable. I tried to boot from the Windows dvd, but I had the same problem again.

  Can someone help me with this problem?

  Thank you

  M. Vilela

  Hi Danielle,

  In addition to the suggestion of Rock Star, you can try the following steps and check if it helps.

  Step 1

  You can first try to start the computer in safe mode and check if you can boot to the desktop. Access the link below and follow the steps to boot to the desktop. To boot to the desktop in safe mode keep tapping key F8 during restart. Once you see the option to start in safe mode select and press to enter.

  http://Windows.Microsoft.com/en-us/Windows7/start-your-computer-in-safe-mode

  Step 2

  If you are able to boot to the desktop in safe mode, you can access to view the history of update on your computer and search for the error code and the updates that failed to install and post it back.

  To view the update history, follow the steps below:

  A. open the control panel (all items view) and click the Windows Update icon.

  B. click on the link to view update history.

  To view the details of a single Windows Update. Select and right-click on a Windows Update list, and then click details.

  Step 3

  I would say also allows you to perform a system restore in safe mode to see if you can restore the computer to an earlier date when it was working fine.

  To restore the operating system to an earlier point in time, follow these steps:

  a. Click Start, type system restore in the search box and then in the list click on the system restore program.

  If you are prompted for an administrator password or a confirmation, type your password or click on continue.

  b. in the System Restore dialog box, click on choose a different restore point and then click Next.

  c. in the list of restore points, click a restore point created before you started having the problem, and then click Next.

  d. click Finish.

  The computer restarts and system files and settings are back to the State they were in when the restore point was created.

  Access the link below to learn more about how to repair the operating system and how torestore configuring operatingsystem to a point in time earlier in Windows:

  http://Windows.Microsoft.com/en-us/Windows7/what-is-system-restore

  I hope this helps. Let us know the results.

  Thank you and best regards,

  Srinivas R

  Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• I have Windows vista Ultimate edition. but he started asking for activation after the windows update while it has already been activated before the update.

  I have Windows vista Ultimate edition. but he started asking for activation after the windows update while it has already been activated before the update.

  Hello, Pichon,

  If Windows Vista application unexpected activation

  On rare occasions, you may be prompted to activate Windows Vista on a computer that did not previously require Windows Vista activation or has already been activated successfully. For example, this may occur on a computer on which Windows Vista was preinstalled by an OEM installation or Volume licensing and are major hardware changes occurred, such as upgrading the hard disk and memory at the same time.

  If you are prompted to reactivate Windows Vista, you can do this by using the Windows Activation Wizard to:

  1. Click Start, and then click computer.
  2. Click System Properties on the toolbar, and then click click here to activate Windows now in the Windows activation area. If you are prompted for an administrator password or a confirmation, type the password, or click continue.
  3. Select the Windows Vista activation method that you want, and then follow the instructions.

  To avoid this problem in the future, obtain the latest service pack for your version of Windows Vista, either through automatic updates or direct download.

  To update to Windows Vista and prevent this activation problem does not happen:

  1. Click Start, click all programs, and then click Windows Update.
  2. Click find updates.
  3. As soon as Windows Vista found the updates, click the install updates button.

  How to activate Windows Vista

  http://support.Microsoft.com/kb/940315

  Activation fails when you try to activate Windows Vista, Windows 7, Windows Server 2008 or Windows Server 2008 R2 on the Internet

  http://support.Microsoft.com/kb/921471

• Satellite P200 - after the BIOS update I can't start the machine

  After the BIOS update I can't boot the laptop because the system doesn't recognize the relecommunicarions password.

  Before updating the password is 0000.
  After when I try to set the password incorrect password start apeeras

  The BIOS password can only be removed from an authorized service provider. So I think that there is no other way.

  On the Toshiba site, you can search the nearest:
  http://EU.computers.Toshiba-Europe.com

• After the last updates of windows have problems with start up and now drivers

  Hello

  After the last updates of windows have problems with start up and now drivers. I get an error code 21 when I try to install the drivers AMD apparently missing.

  May 14, last night I had several (automatically) downloaded windows update

  Today, I was unable to boot my computer with Windows - tried the disk check, start checks etc, and eventually had to use System Restore (for help before the critical update to restore).

  Perfection, everything works, but knowing that windows will attempt to redo an automatic update, tried to check online - no one seemed to have a problem and (naivly) thinking I could always do another restore of the system, I rebooted again.

  Same thing worse. Could not do a sys restore either just before restarting or last night. Chose a date earlier (last week) but then lost the USB drivers and pilots display. Downloaded updated but refuses to let my AMD driver install Windows I have a very unpleasant screen... and I must now stop the installation of this update "critical."

  Would appreciate advice how do my installed display driver or whether anyone else has problems following this update

  Thank you

  Hi Jane,

  You have a disk to install Windows 7 with you?

  I suggest you to check the event viewer for error details report.

  Open event viewer.

  http://Windows.Microsoft.com/en-us/Windows7/open-Event-Viewer

• After the major update W10, Acrobat 9 will not document "% [ProductName: distill] %% found Calibri, using Courier." %% [Error: invalidfont;] "[OffendingCommand: xshow] % '.

  After the major update W10, Acrobat 9 does not create a document not found 'Calibri '.

  It worked doesn't mean anything. 'Inconsistent' means that it was not tested, nor is it updated to work with this version, as it is updated, which can result in what you feel. You can try to run the application in Compatibility Mode, but the chances of work without problems are slim. The real solution is to upgrade to a compatible version.

• Bridge is no longer starts after the last update

  Hello

  After the last update of CC 2015.5 bridge will start is no longer. I get the window that shows that "Adobe Bridge CC unexpectedly quit' almost immediately. Of the window:

  Crashed thread: 0 dispatch queue: com.apple.main - wire

  Exception type: EXC_BAD_ACCESS (SIGSEGV)

  Exception codes: KERN_INVALID_ADDRESS at 0x000000000000000c

  Note the exception: EXC_CORPSE_NOTIFY

  Have uninstalled and reinstalled. preferences ransacked without success. I am running the latest version of the operating system. CC of other apps that I use (PS, I, ID) seem to work. 5 Bridge works fine.

  Any help would be appreciated.

  Thank you

  Ted

  Hi all

  We published a new version of Adobe Bridge (CC 2015) on July 19, 2016. This update is available via the Adobe Creative Cloud application.

  We addressed some crash bridge issues experienced on the launch of the application. Please try the new version and are looking for the crash problems you encountered.

  If you are not able to locate the bridge (CC 2015) on the creative cloud application, you will need to update the creative cloud application and restart your computer.

  Thank you

  Deepak Gupta

• Hi, I have 0xc0000142 error when I start the first pro after the last update, before that I had no problem playing first pro...!

  Hi, I have 0xc0000142 error when I start the first pro after the last update, before that I had no problem playing first pro...!

  Hello Gene,

  You may need to check this: Re: Premiere Pro 2015 won't open after the recent update

  Kind regards

  Navdeep Pandey

• After the last update, the start photoshop it gets for minutes flashes.

  After the last update or after you install the "fuse" CC, the start Photoshop it gets during the minutes flashes. You can't do anything until it stops flashing. It is impossible to work with him. Because there are times that even after you have opened the file it is as if I had something working and takes too much time to perform any operation. And displays an error message. keeps flashing and press 'ESC' to stop and get something. But still, he said, showing the cursor how had tried to open something in the background. One of the moments where I started Photoshop appeared to show two fields seemed 'user' and 'password '.  I tried to remove and reinstall and nothing... still the same thing.

  I installed a previous version of the application to not stop working. I expect a solution to the problem to reinstall the latest version.

  S.O.: Windows 10

  Hardware: Dell Inspiron 5421 - i7 / 8G RAM / Nvidia GT 730 M 2 G

  Thank you

  L.Roma

  I don't think that's the problem. I solved the problem by using an earlier version, while the youngest is not corrected.

  To install an older version I do the following:
  1. open a creative cloud application
  2. in front of 'Find Apps more' I click on "Applications" and change to "show other version."
  3. I have local "Photoshop" and I click on the 'Install' button and chose an older version, in my case, I prefer "CC (2014).
  4. wait for install and now I work normally.

  I hope this has helped.

  Kind regards

  L. Roma

• How to stop ringing? After I have send a message in my iPhone I get six beeps. It started after the new update

  When I send a message on my iPhone I have six beeps just once this has happened after the last update, how do I stop ringing? w

  Check the settings > sounds > text tones and make sure that the sound has not changed. Also, try a forced reboot. Hold down the Home and Sleep/Wake buttons at the same time for about 15 seconds, until the Apple logo appears. You won't lose anything.

• Firefox extension: 'TrueSuite 5.2.500.16' stopped working after the last update of firefox (30.0), although subject: said plugin activated. No difficulty to make it work?

  Firefox extension: 'TrueSuite 5.2.500.16' stopped working after the last update of firefox (30.0), although subject: said plugin activated.

  I tried to reset firefox and search for similar problems, unfortunately found nothing.

  It is also weird empty space before the address in the address bar

  other extensions and addons seems to work very well.

  Firefox 30 spent some less commonly used "Always turned on" plugins "asking to activate. To check and change this to TrueSuite, you can use the page modules. Either:

  • CTRL + SHIFT + a
  • "3-bar" menu button (or tools) > Add-ons

  In the left column, click on Plugins. Then on the right, check the setting on the right side of TrueSuite.

  Any difference?

  Note to other readers: the original poster had to leave Firefox and start it again until it is actually entered into force.

• Single-pass does not work for Web sites after the last update of firefox

  Single-pass does not work for Web sites after the last update of firefox. This works in IE and Chrome and it works under windows (when starting the computer), but not with any website in Firefox.

  Firefox 30 spent some less commonly used "Always turned on" plugins "asking to activate. To check and change this to SimplePass, you can use the page modules. Either:

  • CTRL + SHIFT + a
  • "3-bar" menu button (or tools) > Add-ons

  In the left column, click on Plugins. Then on the right, check the control on the right side of the SimplePass.

  You may need to exit Firefox and start it again before it takes effect.

  A little luck?