No works Web interface access vlan but ping

Similar Questions

• newbie question about obtaining work web interface 3424 and 3448

  Hello everyone - first assignment in time-

  I have a 3424 and 3448 who seems to have the same symptoms.  I am able to get both working as I want, but I am unable to get either to respond to a request for a Web page or a ping.

  Here is a copy/paste of what I see:

  Console # show ip interface

  Activity of Type status IP gateway
  ----------------------- -------- -----------------------

  IP address I / F Type
  ----------------------- ---------------------- ---------
  192.168.0.100/24 vlan 1 static

  According to my research, which should allow me to go to a browser and type 192.168.0.100 (my nic is 0.99) and access the Web page, but no Web site appeared.

  this site suggests that I should be able to ping:

  Console # ping 192.168.0.100

  but I do not see a ping response.

  I KNOW it should be easy, but I must be missing something very obvious.  after reading this I've also tried

  IP http server
  The https server IP

  no errors, but still no answer ping or Web page.

  any help or suggestion is the most appreciated!

  solved...

  two different solutions:

  (1) view of brand-net snmp-server community rw DefaultSuper

  (2) all back, start again and go with all defects, which will prompt you to everything.  Then set the ports accordingly.

• ACS WORKS, BUT NOT THE GRAPHIC WEB INTERFACE

  I have a worm ACS 5.4.0.46.7 running on a device, ACS-1121-K9. After the restart of a Win2008 controller it has stopped working and someone in my Department and restarted the ACS. It seems that authentications are working now, but I can't access the web gui. It answers ping and ssh. I did a web show acs-config-Interface and the display Interface has been disabled, I allowed him but it still does not work:

  TBGACS02 / admin # show interface web-config-acs
  interface of migration is disabled
  the UCP interface is disabled
  display interface is enabled
  REST interface is disabled

  TBGACS02 / admin # display the status of the acs application

  Role of the ACS: PRIMARY

  Process of database ' ' running
  Treat the race of 'management' (HTTP is insensitive)
  Unguarded "runtime" process
  "Adclient" process running
  'Ntpd' running process
  "View-database" running process
  The "view-jobmanager" process execution failed
  "View-alertmanager' running process
  "Notice-collector' running process
  "View-logprocessor' running process

  I could try to restart again, but I'd rather not if possible...

  Hello

  Can you try 'application acs stop' and then start CSA application and see if that solves the problem?

  If this isn't the case, then I suggest to take a show technician and support bundle, prosecute with TAC.

  Kind regards

  Kanwal

  Note: Please check if they are useful.

• Help - LI running, but get Apache2 Ubuntu default page while trying to access the Web interface of log insight

  Hello

  I installed the Log Insight 2.5 VM via vCenter Server ESXi 5, 5. I was able to deploy the virtual computer successfully and you can see the network through VAPP Options settings. (Attached picture - TIME settings).

  Question:

  Unable to access LI web Interface. While trying to access the Web interface, I get 'Apache2 Ubuntu by default Page' (img attachment). Insight of the newspaper runs and opens the web application on port 80.

  Newspapers, controlled far-

  status of /etc/init.d/loginsight

  Open a session running Insight

  Attached image Loginsight2-DURATION - file /storage/core/loginsight/var/runtime.log

  # sh li - cassandra.sh - status

  SH: li-cassandra-sh: not found

  Check if the tcp 80 port is open through the netstat command. Yes, it is open.

  Telnet on port 80, it says connection and crashes. Image attached - telnet-LI

  Able to ping the IP address successfully.

  How can I check http logs on console LI?

  I would really appreciate response to this soon. I'm working on installation LI for more than a week and struggling to get through this way.

  Thank you

  Radhika

  I believe that you with the configuration, but I tell you that the configured IP address and the IP you hit in your browser are not still the same IP, Log Insight does not work on Ubuntu, so you hit another system. To prove this, connect you to the console of the Insight newspaper and run:

  # cat/etc/SuSE - release

  SUSE Linux Enterprise Server 11 (x86_64)

  VERSION = 11

  PATCHLEVEL = 2

  You will see that you are running SuSE to see a Ubuntu screen tells me that you have an IP address duplicate in your environment and you hit a node that is not an Insight newspaper. I hope this helps!

• N3048 access to the Web Interface without OOB

  I recently had our switch replaced by RMA and have access to the web interface via oob. I'm not sure how to access ports and other subnets and want to access the web interface of the server room outside. It's probably something very obvious, but I don't have the original switch to check the configuration. Any help would be appreciated. Thank you.

  You can use in-band or oob access to administration from inside or outside the server room.  The port of oob is a completely separate network used for management only, but you can also use a port in the Strip management.  By default, VLAN 1 is usually used in the Strip to transport of management traffic.  If you set an IP address on VLAN 1 you should also be able to manage from this IP address.  Measures would be to define the IP address on VLAN 1, ping ping to test connectivity, remote and then use your browser to connect to the web INTERFACE.  You should be able to use the same username/password that was used for the oob port.  Without a set of name of user and password, the web INTERFACE will not allow the session.

  B

• VLAN and the SSID does not not in the Web Interface

  We have a couple of APs which do not show the VLAN and via the web interface of AP SSID.  If you go to the SSID Manager page in the web interface, the page rises but doesn't show any SSID configured.  It goes the same for Services - Vlan.  This page appears but does not show in any VLANS configured.  If you telnet to the APs, you see the mssid listed and all the SSID interfaces.  The SSID on the access point is functional and working.  It is just so hard to use the web interface for these APs.  I tried to compare configs running on APs where the web interface does not show this and APs that it shows, but cannot see any differences.

  Thank you.

  Have you tried with different browsers?

  Nicolas

• Web interface works is not the well-known address of management

  TLDR:

  • opening webinterface on ip management group-> does not work / ping
  • opening webinterface on eql management ip-> works
  • opening webinterface on ip management group-> suddenly done work
  • Why?

  Yesterday I've updated SanHQ of 2.2 to 3.0.1 to prepare to run the path to upgrade to FW 7.x. Since yesterday, I get the following warning:

  [ID: 1.6] The eql-grp01 group has been added using non well known address (MWKA). Delete and add the group using the well-known address of management of group 172.16.0.9.

  The eql-grp01 group contains a single EQL (eql01 / 172.16.3.15) and has a dedicated management port. The beach is a 16, as such, both the IP and IP management EQL management group are in the same network (again).

  I'm able to reach the Web interface of eql01 on 172.16.3.15 without problems for years. Try to reach the Web interface on 172.16.0.9 has always given problems (timeout, ping works however) until I asked the Web interface on 172.16.3.15, after that, I can reach the Web interface without problems on 172.16.0.9.

  Up until now I did not worth to look into it, but as I'll be add another Member to the group within a few weeks and SanHQ's "tenacious" on do not use well-known management IP address I have tought I might give it a try here, maybe it's the behavior?

  Edit: Adjusted the subject as non-MWKA does not work but the MWKA (submits sugested otherwise)

  OK, you need remove the SANHQ and add in it through the Well Known management address.

  I don't know why he first had to go to the Member port Mgmt vs being able to use the IP alias for group management.

  That's all the management IP address is, like the IP address of the ISCSI discovery.  It is a superior a physical port IP alias.   So if you can reach the Member IP address, you will have no problem reaching the alias.

  Maybe something on your network, or the ARP table has not been updated.

• Unable to access the web interface for SG200-18

  Hello

  I got a new switch and I am trying to connect a UCS.  I ping the switch very well, but when I try to use IE8 or firefox, I can't go to the web interface to configure.

  Here is my configuration:

  Cisco UCS C210 M2

  IP = 192.168.1.100

  Subnet = 255.555.255.0

  Default gateway = 192.168.1.1

  Switch SG200-18

  Default IP = 192.168.1.254 (it is not DHCP)

  Any pointers?

  Tom G

  You need to set a static IP on the PC that is connected to the switch. The IP address of the PC

  must be on the same subnet as the 192.168.1.254.  You may need to try something lower to IE8. Should be

  works with Firefox and IE7. There is also a browser called GreenBrowser which works usually with switches.

  Thank you

  Rick Roe

  Cisco Small Business Support Center

• HP 8500 replaced, software does not detect printer even though I can't ping / connect to the web interface

  Windows 7 Pro 64

  Reference Dell

  Printer connected via ethernet

  software worked well until the printer has been replaced by HP under warranty

  in the new device, the screen of the wizard to set the time/language etc.

  Software HP does not detect the device and so I can not use all the features.

  I can connect to the printer via IP and also tried to put the TCP/IP port with printer static IP. Can I print using this, but the software "suite" does not detect the printer.

  Removed all software, cleaned the registry, removed the IP port, re-installed the software, does still not detect printer.

  Installed HP printer diags and it passes all the tests, but the suite software HP will always be NOT detect printer.

  Tried without firewall, tried with, still can ping printer, connect to the web interface, the static value, always the software does not detect the printer... so whats left to please other than an another replacement warranty which is used to solve the problem, as it is definitely bad coding in the suite.

  I also tried downloading drivers/full later on the HP site.

  Note that all windows updates are met, reconstruction is out of the question that it is a machine of the company and would almost take me 3-4 days to replace all the software on it (Sage, DW, COFFEE, HMRC).

  Hi-Dillion, Declan

• PC54x8 access to the web interface of WS2012

  Hello. We have a strange problem. Because we are not networking gurus, we use the web interface of the switches to manage them (instead of using the CLI). The problem is that when connect us to the web interface of WS2012, the browser (IE) freezes. We tried this on several machines of WS2012.

  Management of WS2008 R2 works without problem.

  Is this a compatibility issue with IE10 (WS2012) compared to IE9 (WS2008 R2) or something else? I tried to add the address IP for trusted sites, but that did not help. Unfortunately only the servers with WS2012 are connected to this particular switch, so we are unable to manage it more (from the web interface).

  Any ideas what could be the cause of this? The web interface requires Java? Given that we have not installed on WS2012 servers.

  Unfortunately I found no work around to get the software to work with IE10. The recommended solution is to use another browser, which as you've found, works very well. I believe that the idea is that in future updates that IE10 will be supported, but I don't have a roadmap on how that would be released.

• SX10 - how to access the web interface behind a firewall

  Howdy

  I have a very simple configuration, router and behind her SX10. I can't access the web interface of the remote unit. Is there a port that I need to activate or something?

  When the device was connected directly to the modem, with the public IP address, I was able to connect to the web interface.

  any suggestions here?

  I enter anything in the field AllowRemote.

  Thanks in advance!

  Web interface can be accessed using HTTP ether (80) or HTTPS (443).  To you how you want to deploy, but you can use NAT on the router, port forwarding, or even put the SX10 in DMZ on the router.

• Trying to access Web Interface WRT54G

  Hi all.

  I have a Linksys WRT54G, and I try to access the Web Interface of the router. The problem I have is that whenever I try to access the Web Interface, the router stops internet connection for all devices connected to them, they are wired or wireless broadcasting. The only way for me to find the internet connection is to insert the SetupWizard disc and go back through setting all things.

  I need to access the Interface so that I can enable port forwarding.

  Any help would be greatly appreciated. Thanks in advance.

  Are you sure your firewall on the computer (including the Windows Firewall) is off?  Some firewall is very difficult to put out.  In addition, disable your pop-up Blocker.

  To make an update of the firmware (or re-install), you will need to use the tftp.exe program.  The instuctions throughout the proceedings (including the tftp.exe info) can be found here:

  http://Linksys.custhelp.com/cgi-bin/Linksys.cfg/php/enduser/std_adp.php?p_faqid=3703&p_created=11515...

  After the installation of the firmware, don't forget to reset the default router, and then configure the router again from scratch.

• Access SupportAssist web interface from another computer?

  Hello

  I installed the Version 1.3.0.148 of SupportAssist for servers and I can't access the web interface from another computer, only from the server I have installed.

  I could not find in something configuration files allow only localhost.

  Is it possible to make the web interface available to other computers on the same LAN?

  Thank you

  Version 1.3.0.148 for servers

  Hello

  You can also access the SupportAssist on a remote system if the 2607 port is open on the system where the SupportAssist is installed.

  You can use the following URL to access help support

  https://

  installed >: 2607/SupportAssist

  Hope this helps

  Thank you

  Christelle

• Cisco SX20 - cannot access web interface after factory reset

  Hi guys,.

  I just did a factory reset on my SX20,

  and now I can't access the web interface, I need to add the key to release

  Basically I can't configure the IP addresses directly through the Executive Director of unity
   
  I need to add the release key and access to any interface
  Help, please!

  SX20 Cisco TC6.3.0

  You can access the settings locally using the remote?

  If so, you should be able the enable http as well as the fixed IP address using the remote control.

  The factory reset should have change setting IP DHCP, so if it has a network connection, this IP address must be included in the top of the page, to the left of the screen.

  /Jens

  Please note the answers and score the questions as "answered" as appropriate.

• I have the latest version of Smart Web Printing 4.6 but it does not work. Why?

  I have a netbook Acer running the Windows XP operating system and Internet Explorer 8.  The latest version of Smart Web Printing is supposed to work with them, but it is more the fact.  I see warnings that it does not work with Internet Explorer 9, but that is not what I have.  I have the image of the web page and a smaller version of the same thing where I should have the box clip options.  The only option I get is one on top to close.

  You will need:

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=MP-79585-2&cc=us&DLC=en&LC=en&OS=228&product=3441026&sw_lang=