NOR-7344 interface with IP M-415. DG possible steps?

Similar Questions

• Encoder interfaced with NOR-9401

  I bought a coder who has open collector and resistance to pull-up 3.3 kohm (TTL) logic output.

  The encoder comes with four sons: power + 5V, GND, channel A and channel B. channel A and B are logic output.

  Channel A and B are connected to the OID of NOR-9401 which is mounted on the cRIO.

  A standard VI for encoder counting is used and compiled under the FPGA environment.

  During the measurement, I have observed that there are number of significant loss in both directions encoder.

  I don't think that there is a problem with VI like I used it several times on the encoders with output RS422.

  Is there a problem with my current encoder with respect to its electrical interface with NOR-9401?

  Thank you.

  I don't think that there is a problem with pull-up resistance. Even if the digital IO ports have their own resistance to pull-up (usually of the order of 4.7kOhm - should be included in the manual), the power to be handled by the circuit of encoder output transistor is about 2mA. -Check your configuration for a correct connection GND. You must connect the encoder directly power GND to DGND to the printed circuit board Terminal.

• How the interface with my RND4000?

  I'm a replacement IT here. I have almost no notes to work from, and I've never used a SIN.

  How the interface with my RND4000? I tried to put the IP address in a web browser and you get "unable to connect".

  I think the NAS is supposed to be "hosted" on one of my servers. How to determine what is the server?

  Hello Helpdesk-Kerry,

  Then, it should be accessible. Perhaps, try another computer if after restarting it does not open yet?

  Kind regards

• On a NI USB 4432 device, any C++ APIs, interface with C++ application module.

  1.C ++ API - can I interface with the NI USB 4432 through a C/C++ application, she api C/C++ or dll.
  Need to get the entry/signals of the module in a C/C++ application.
  2. compatibility - information of the BONE, is the product drivers Windows XPE (XP Embedded) compatible?
  3. any link/site for documentation full on the module

  You must use the NI-DAQmx driver

  http://www.NI.com/dataacquisition/nidaqmx.htm

• Interfacing with several unknown USB devices; all producing NMEA strings

  Hi all

  Question about the peripheral USB interface and their associated drivers.

  I have the obligation to build an application that interacts with the USB devices that produce NMEA strings. I have the library to parse NMEA strings, but I fight with interfacing with several unknown USB devices. When deploying applications, I know not all possible USB devices to use.

  Is it possible to produce one driver who will accept any USB device strings?

  Or, more likely, is there a way to get the LV to recognize a connected USB device and automatically find / install the driver like windows does and is it possible to do in a deployed application?

  I had a trawl of the forums, but I've not found anything that specific.

  Thanks, I really appreciate the help.

  About the VI "set up the serial port", my problem is that the choice of COM port is in a separate menu (not directly related to the VI) and it allows all possible COM ports to be selected. That can be addressed.

  I am not expecting an all-in-one solution but asked the question in case it was possible.

  What I realized, is that for my specific condition to read strings from a USB device. It is likely to be sent over a serial connection. LV can handle this well and easily assuming the device has the installed driver / settings are available.

  LV (and indeed any other program) will not work without a device driver / settings. In this case, parameters set must be found (error) / a USB RAW driver would need to be developed. Devices requirng a RAW USB driver would need a serious review to continue due to the time and effort required. All this effort is work inherited from the AIDS to navigation

  I appreciate any help and I think I got the answer I was looking for! Thank you very much

• LabVIEW interface with micro contoller

  I'm new to labview. I need to know if the DAQ card is necessary to interface with micro controller? If no need then one can you explain how inter face microcontroller 89c 51 with Labview... If necessary, explain how interface?

  JEAN ASOKAN

  
  

• A module C - DAQ exists which will interface with standard RV - C?

  Module C - DAQ exists that if interface with standard RV - C (vehicles recreational CAN)? RV - C seems to be a variant of J1939 according to Wikipedia.

  I would use 9861 OR or NI 9862. I'm new on CAN protocol and evaluate some assistance.

  I've never used RV - can, but according to Wikipedia, the rate is 250Kbaud, so you'll want high speed CAN peripheral, 9862, you can set baud rate on init of the material.  After installing XNet and cDAQ software, you have a max bus monitor and several examples in the example Finder to read and write raw images.  After that, you'll want to read on the standard to understand how to format and analyze the data.

  Also if you have any questions, you can post on the Sub-forum Auto , they can probably answer more specific questions.

• How to speed up loop DAQ triggered using NOR cDAQ-9174 with NOR-9215 and NOR-9402

  Hello

  I use LV2010 and NOR-DAQmx 9.2.2. I have a NOR cDAQ-9174 with a NEITHER-9215 4 channel 100 k simultaneous ADC and NOR-9402 4 channel DIO module trigger and reset.

  We run WinXP sp3 on a Dell M4400 core 2 duo @2. 26 Ghz.

  I used the code example NI DAQmx for acquisition of tension with trigger HW. My goal is to try all 4 channels on the 9215 simultaneously when a trigger is received on channel 0 of the 9402, after data is read, I use channel 1 on the 9402 to reset the trigger of the target material.  I have a version of this work, however the maximum event rate is ~ 16/second. I have the Setup 9215 for finite samples / 10 samples per channel which is ~ 400uSec of conversion time and I realize he is above in the appeal of vi, but ~ 50mSeconds worth?

  The target detector can put out up to 1 k / event triggers / seconds.  Only, I received a rate of 8 per second and I added the NOR-DAQmx control vi driver and chose "commit" this did double the rate.

  My question is what is the maximum rate of loop for these devices (trigger/conversion/reading device / reset) and start over? I noticed that just let free the 9215, carried out using the 'Acq & chart internal strain Clk' raised only the rate of events up to 20 Hz.

  Thank you

  normbo663

  Hi normbo663,

  You can get this works far better assuming you have an available counter (there are 4 on the backplane of the 9174).

  DAQ Compact supports the tasks of meter output "redeclenchables" that can be used to generate a finite pulse train.  You can set a task of finished meter redeclenchables output to be used as sample for your task of analog clock.  The task of the meter output will be re-Army (less than 12, 5-25 ns) as soon as it's finished out the last pulse.  The task of analog input would be configured to run continuously, but it would only sample based on the output of the meter triggered.  For an example, see here.

  You can reference the internal counters on the cDAQ without signals through a routing module using: cDAQ1/_ctr0 (right click on the chain counter control, then select i/o name of filtering and check channels internal to add these options to the drop down).

  Thus, with the tips above, you should be able to immediately re - arming your analog acquisition on the 9215 using one background basket counters.  It seems that the second half of the application is to use a second channel on the 9402 to reset the trigger of your DUT.  You can deterministically generate this signal so by configuring a 2nd redeclenchables meter out task (single pulse, but this time).  All you need to do is the initial delay on the appropriate value for your analog acquisition.  Trigger this counter on the same PFI line that trigger you your analog task from.

  Using counters to generate the signals you need in a deterministic way, the loop becomes is no longer a problem (as long as your input buffer does not overflow).  You may need to re-read several triggers at the same time for the loop to keep (for example to read 1000 samples each, which would correspond to 100 triggers 10 samples).

  Best regards

• I use pci-6221, I need her to interface with thermocouple with voltage up to 5v

  I use as my pci-6221 or data acquisition card and card 8.2.this labview version gives the constant 10.5 volt signal in at the entrance to analog channel AO on pin 68 and 34. why it shows 10.5 although I did not connect any input.i use type k thermocouple and after signal conditioning with tl0804 I need it interface with AI 0.i channel unaware aware of off the road on the output pins this Card.i need to operate an electric rod that needs 24 volt DC.i give entry to the pins HAVE with variable dc power block after reaching the limit I set(eg:2v) it jumps instantly to 10.5 volts.

  You have your task to acquisition of data configured for the mode differential or asymmetric acquisition for the analog input?

  I don't understand your comment about to connect the pins WITH a DC power supply.  Why is that you connect a DC power supply to the analog input?

  Using an analog output or digital output to operate the electric rod?  I'll assume that you are looking for on/off control.  A digital output is not the voltage or current to drive something that big.  You may be able to find a relay for coil 5VDC.  Check current requirements.  With which you can have the relay to connect or disconnect a power supply of 24 VDC is the actuator.  Make sure you have a protection diode across the relay coil wired, so that the magnetic field of the coil does not damage the analog output of your card.

  Another possibility is to have the 5 VDC output transistor circuit switches the 24 VDC circuit.

• How to upgrade Exployer 7 Exployer 9 interfacing with Vista

  I can't update my browser Exployer 7 to 9.  I interface with Vista premium.  I am currently with all updates at the moment and I used the fix online micro-soft option.  What I am doing wrong?

  You have installed Vista SP2?

  Direct download: http://www.microsoft.com/en-us/download/internet-explorer-9-details.aspx

  or http://www.microsoft.com/en-us/download/internet-explorer-9-details.aspx

  Depending on whether you are a 32-bit or a 64-bit system.

  More information: http://windows.microsoft.com/en-au/internet-explorer/downloads/ie-9/worldwide-languages

  For more information, see How to install or uninstall Internet Explorer 9?

  If you need help find which version of Windows you are running, see my computer run the 32-bit version or 64-bit Windows?

  Also for more information:

  http://support.Microsoft.com/kb/2399238

  Prerequisites to install Internet Explorer 9

  http://support.Microsoft.com/kb/2409098

  How to fix Internet Explorer 9 installation problems

• USB human interface with the brand lleyow

  Please I frequently have problem with usb human interface with the brand of lleyow next to bet.

  Pease how can I fix this problem driver version 6.0.6000.16386 windows vista pk2 thanks

  Hi thonson35,

  ·         Have you made changes on the computer before this problem?

  ·         You get the error message?

  ·         Do you have any human Interface device attached to the computer which does not (such as the keyboard, mouse and joysticks)?

  I suggest you to uninstall and reinstall all devices interface. Follow these steps:

  1. Click Start, type device Search Manager and press to enter.

  2. Device Manager window opens, expand Interface devices.

  3 right-click every device under the peripheral Interface node and then click on uninstall to remove them one at a time.

  4 restart your computer, windows will reinstall the Human Interface Devices.

  5. perform a test to ensure that the problem is solved.

• IP IVR interfacing with SAP

  We are about to implement the Cisco IP IVR linking to our AS / 400. We have it with our current IVR, so it's easy. In a few months, we operate off the coast of the AS400 to an implementation of SAP for inventory and accounts of users and all this other nonsense. Someone has interfaced with success the IVR and SAP to let me know if this is possible?

  I guess you have to go through third-party programs, such as Java and VXML. We have a customer who use Java with Websphere measures.

  Wei

• BlackBerry smartphones POINT HOT or ATTACHMENT for BB 9310 on BOOST / Network Interface with Android Tablet operating system Ice Cream Sandwich 4.0.3 SPRINT

  I know that technically and could use step by step Instructions how to set up a

  HOT SPOT or ATTACHMENT for BB 9310 on BOOST / Network Interface with Android Tablet operating system ICS 4.0.3 SPRINT

  Please explain it to me like I'm a 12 year old (LOL)

  If you could email, mail, or call me at the following (see below) it would be MOST APPRECIATED

  David Lurie

  Affordable tracking systems

  1063 mosser road

  Building C-202

  Breinigsville, PA 18031 us.

  (610) 972-2110

  [email protected]

  P.S. If I can ever help with GPS Tracking, My Business in which I have 12 years of experience, I'll be more than happy to give back

  If push does not support the Hotspot feature there is nothing you can do.

• Since the installation of EL CAPITAN, I can't open pictures and iPhotos with photoshop, CS6, nor my mails with Office Word

  Since the installation of EL CAPITAN, I can't open pictures and iPhotos with PHOTOSHOP CS6, nor my mails with office Word

  Hi denisb,

  If you are not able to open the Photos App images directly in Photoshop then, this is the expected behavior as App Photos does not allow for any third-party application interact with it directly.

  You must export images from the Photos App and then open in Photoshop.

  Refer to this link: How to use an external editor with Photos for OSX | IVous

• Are there ways to OBIEE interface with client application?

  Our OBIEE 10.3.4 on Redhat, OBIEE version to connect to an Oracle Database 11.2.0.2 running on the same box of Redhat like OBIEE. Our application is based on java web application you use Tomcat, he point to the OLTP of Oracle Database 11.2.0.2 on a dedicated server from Redhat.
  
  One of the requirements for the original application was logical with complecated OLTP data process and create reports in text files. The customer wants now OBI allows you to view, print, and distribute reports. The best way to meet this requirement of change to the advanced stage of development seem to interface with OBIEE application, if at all possible. In this way, by clicking on a button in the GUI of the application, a stream of formatted data is sent to the OBI Stardoll service in response to a request. A client OBI page will then be displayed to shpw reports and allow users to print and distribute.
  
  Now there is some OBI API that allows an application to call to interface with OBIEE?
  
  Thank you.

  Hello

  I do not gave more experience with this subject, but I guess that's what you're looking for;

  http://download.Oracle.com/docs/CD/E12096_01/books/AnyWebServ/AnyWebServ_Overview3.html

  You might have to do some more research.

  Maybe Vincent could be of any help.

  http://oraclebizint.WordPress.com/2007/07/31/customizing-Obi-EE-SOAP-API/

  Good luck

  Daan Bakboord
  http://obibb.WordPress.com