Similar Questions

• MAX does not recognize NOR-DAQ traditional (old) devices * HELP

  I have a card PCIe-6259.  I want to use blocks of input-output in my program .vi (read Port DIO-DIO Port writing reading Digital Line), so I installed the version of NOR-DAQ traditional (old) devices 7.4.4.   But when I got to MAX (measures & Automation) and look on the left side under devices and Interfaces, I do not see the Tradional-NOR-DAQ tab; I see only the devices NOR-DAQ-mx, PXI, series and parallel system.

  Then when I go to run my program I get the error: error-10401 took place in a DIO Port Config Possible reason (s): NOR-DAQ LV: the specified device is not a product of National Instruments, the driver does not support the device (for example, the pilot exited until the device has been supported), or the device has not been configured using the Explorer Measurement & Automation.

  So, how do MAX to recognize that I have installed NOR-DAQ traditional (old) 7.4.4?

  Thanks for the reply!  I realized this too after going through the files for example... but thanks for the confirmation.

• The measurement and Automation Explorer is completely empty. No idea why?

  Hello

  When I open Measurement & Automation Explorer, there is nothing in the main boxes, boxes are completely empty. The top toolbar with file/Edit/tools is there, but all that is empty.

  I had good success with the SCXI-1000 chassis in a few years when I did further research at another University. At my new University, it gave me access to an SCXI-1000 chassis with an SCXI-1600 module to connect to the computer via USB. I reinstalled windows on an old computer to 64-bit, had the hand of the entire system, the Measurment and Autiomation Explorer open as expected, then was that NEITHER ceased support for the SCXI-1600 on a Win 7 Pro 64-bit modules. So, I've divided the hard drive into two partitions, installed Win 7 Pro 32 bit and reinstalled NOR then installed the updates for a few hours.

  When I try to turn on measurement and Automation Explorer, there is nothing in the window. What can I do to get the various boxes? I went to tools > reset Configuration data.

  

  Nicholas,

  I recently saw a similar problem on another post. This person has received the exact same blank screen because Windows Firewall has blocked MAX (nimax.exe). Try turning off your firewall temporarily and then see if MAX runs. If so, you will need to add an exception in your firewall settings. If this isn't the case, you could have operated in a corrupted installation and the need to do a repair.

  Ryan

• 6602 not detected measurement and Automation Explorer or Windows 7 Device Manager

  I have a PCI-6602, in a PC that is running windows 7 Home premium and it appearing not not in the Device Manager and as a result measurement and Automation Explorer.  What is strange, is that I don't see either the PCIe-6535.

  Hey M,

  Unfortunately if the windows Device Manager is unable to see the devices on multiple computers, it certainly points to the cards being broken.  I recommend you head over to http://www.ni.com/support/ and create a Service request to begin the process of repair for these devices.

• You want to know the NI-VISA order in measurement and Automation Explorer

  Hello

  I use measure and Explorer of automation to connect my equipment through LAN and it works well.

  But this device does not detect my code VBA with Ni-VISA. I want to know how the software (measurement and Automation Explorer) generates the connection and reading the message of compression inside the unit.

  It's my code. I check the read back value if it is "100 connection accepted."
  ----
  Public Function VNAconnection() As Boolean
  = stat viOpenDefaultRM (defaultRM)
  msDly (1000)
  Stat = viOpen (defaultRM, ' TCPIP0::10.85.148.60::5000:OCKET ", VI_NULL, 20000, NETWORK" ')
  msDly (1000)
  = stat viSetAttribute (RÉÉS, VI_ATTR_TMO_VALUE, 15000)
  msDly (1000)
  Feedbk = Space (80)
  status ("Waiting for connection VNA")
  = stat viBufRead (NETWORK feedbk, Len (feedbk), Actual_Length)
  If InStr (left (feedbk, Actual_Length), "accepted") = 0 Then

  MsgBox "error has occurred. Ethernet connection not accepted! »
  NETWORK viClose

  viClose defaultRM

  VNAconnection = False

  Exit Function

  End If
  End Function

  Thank you

  Michelle,

  I found I need to add viWritebuff to * IDN, equipment, then he will answer a message accepted.

  Thank you

  Xin

• Measurement and Automation Explorer

  Hello

  I use the controller measurement and automation. It has detected my usb USB-HS-GPIB interface, up to now, no problem.

  I have a device connected Keithley, I want to detect, but there is no scan button for devices when I go into my USB interface. He's just "open test VISA Panel' and 'Save' buttons. Any idea what the reason could be?

  It does not show the unit. Screenshot is attached.

  Kind regards

  Guy

  I had problems with the old version of MAX do not recognize USB devices correctly. OR recommend the latest version of MAX to solve the problem. I would not recommend the old version 2.7 or 2.8 and MAX that comes with them. I had to install the DAQmx 9.0 x to get the last MAXIMUM to solve the problem. It has been incorrectly grateful as USB devices or instruments. When I've updated DAQmx and MAX I then could finally remove the list of bad devices.

• AVT Marlin not recognized by measurement and Automation Explorer

  Hi all

  I use an AVT Marlin F046B on Windows 7 and sometimes this camera is not recognized by Machin Vision: measurement and Automation 5.0 (MAX), no IEEE 1394 devices is displayed.

  This problem appears randomly. When the camera is not recognized by MAX, if I use the driver of the TRA for IEEE1394 card, the camera is recognized by AVT SmartView and when I installed the driver of return of Microsoft for IEEE1394 card, the camera is not always recognized by MAX.

  Could there be a problem of compatibility somewhere?

  Thanks in advance,

  Hello gege91,

  It is a driver problem Windows 7. Please see the following link for more details:

  http://www.alliedvisiontec.com/EMEA/support/knowledge-base.html?tx_nawavtknowledgebase_piList [uid] = 1...

  Oliver

• Keithley 2000 not identified NOR Measurement and Automation Explorer using GPIB

  Hello

  I recently used NI TestStand and NI MAX with IVI drivers to get my working(using USB) peripheral. He has worked successfully for TG5011 and TDS1002B Oscilloscope function generator.

  Following the same procedure: I started with 2000 model DMM of Keithley with GPIB.

  I am facing difficulties in finding my camera on OR-MAX devices and interfaces. I use a GPIB KUSB - 488B USB adapter to connect.

  I can interact with the device of VISA Interactive Control and KUSB diagnosis tool and you can see the device in the device Windows and KI-Configuration Utility Manager. Surprisingly, I don't see GPIB Board in the NOT-MAX.

  Help, please.

  System details: NI-VISA 5.2 installed on Windows 7, KUSB-488 driver installed in command compatibility mode OR. (only ieee_32m.dll is present), installed UN NOR-488.

  Thank you

  Martin

  To help all those who have read this thread:

  I had the Keithley 2000 NOR-MAX and NOR-Test Stand using IVI Driver (for Keithley 2000 of NOR) using the KUSB - 488 B (GPIB to USB adapt from Keithley).

  Layer of keithley installed IO Keithley and I can see the unit property. I then followed the procedure for IVI MAX and TestStand pilot program and IT WORKED!

  Please find attached the screenshots for Visual clarity.

  Thank you and best regards,

• 6009 USB appears in the devices, but no measurement and Automation Explorer Manager

  I have a NI USB 6009, which is visible through Windows, but not in MAX.  Uses OR-DAQmx 9.0.2 (so it should date back to before the question HID/PID, I've read).  See the attached screenshots.

  I suspect I'm missing something.  What?

  Sounds like a classic MAX database corruption.

  There are methods to go through and fix it... they are quite complex and convoluted.  More simple is to uninstall/reinstall just MAX.  Your version of some 9.4.0f1 with the Windows XP hotfix versions works well for this same problem on several machines here, looks like out for download 9.5 now.

• No COM port available in the measurement and Automation Explorer

  Hi all

  I installed Labview version 9.0 (32-bit version) on a computer running Windows XP with Explorer Measurement & Automation. When I opened it, the program cannot find the COM or LPT ports. Anyone has a solution on what to do?

  Equip your CD/DVD device driver and reinstall the device drivers.

• measurement and automation explore (MAX) version 4.1.0.3001

  Hello

  I used MAX recently and he suggested a firmware update, which at the time I said no.  Now whenever I start

  MAX and select, my device under devices and Interfaces I simply get a message waiting hourglass, no error message

  are visible.  What would be the best way to solve this problem?  It gives me is more a chance to update the firmware for my motion controller

  device.

  Treyphond

  Treyphond,

  I have not seen behavior like this before. Please uninstall NOR Motion, disconnect your motion control board, reinstall the latest version of NOR-Motion and reinstall your Board again. Please let me know if this solves the problem.

  Thank you

  Jochen Klier

  National Instruments

• measurement and automation

  I'm just starting using the measurement and Automation Explorer.   Half an hour ago, I performed a calibration of temperature to get familiar with the process.  It seemed to work.

  I tried calibrate again.  It says my current calibration is 31/12/1903 - Question 1) why is this?

  I pressed the button , then came the name of my Stallion, then

  I left the characteristics of calibration because it was one of the screen: 1000 samples at a frequency of 1000 hz, then I pressed

  I received the following message is displayed:

  Error 50103 the DAQ Assistant.  -Question 2) what is this error code for

  Question 3) where can I find a list of error code numbers and their meaning?

  Thank you

  jdsnyder

  OK, now the problem is finally solved!  I re - adjust the device.

  At work the first time, he then had to be reset.

  Thank you

  Jon SNyder

• NOR-DAQ traditional vi not found in NOR-DAQmx

  Hello. We hope to control a detector via NI PCI-6533 (DIO-32HS). Our colleagues have implemented control programs in BT 7.1 to 7.3 of NOR-DAQ traditional. Now when we opened their programs on a PC installed with LV 8.6 and NOR-DAQmx 8.9, many vi was not located, including "DIO config.vi", "DIO wait.vi", "DIO clear.vi", "DIO read.vi", "Reset.vi Device", etc. We realized that they were supposed to come from vi.lib\daq\digital.llb and a few other .llb in the same folder. Apparently vi.llb\daq was installed by the traditional DAQ.

  We do not believe there is compatible with LV 8.6 traditional DAQ, which means that we need to replace those 'DIO *.vi' or 'Device reset.vi' with their counterparts DAQmx.  Could someone shed some light on how we should start working on that?

  Thank you very much.

  Xiaolan,

  Indeed, there is a traditional DAQ driver for LV 8.6. The installation can be found here.  I hope this helps.

• Measurement and automation - cannot initialize camera

  I am developing software to interact with GigE Vision cameras and having a visible Dalsa Genie HD camera I've used during development. I also have been using software OR measurement and automation to verify my software does what it is supposed to.

  Well everthing worked fine and nothing has changed except for a three-day weekend, but now I get a "IMAQ 0xBFF6902C error - unable to connect to the camera' when using the software OR measurement and automation. When I lauch the softwar I click 'Devices and Interfaces'-> "NOR-IMAQdx devices" and my camera picture appears in the list, but when I click on the camera to connect I get the error.

  I tried to connect to another camera with the exact same configuration (hardware and software), but everything works as it should.

  Any ideas? I tried a lot of things

  Thanks in advance.

  Troubleshooting of the GigE Vision cameras

  Also if you use multiple cameras are the names different to one another?

• Measurement and automation cannot find the pxi-6070e in the Groove 3

  I just moved my PXI-1002, containing a PXI-6070e in the Groove 3, to a new computer. The new computer is Vista. I installed the drivers of NOR and measurement and automation (via NIDAQ880f2). After connecting the chassis and turn on the computer, M & A sees the chassis but says the range containing the 6070E is empty. The link and the power lights are lit (green) on the 6070E. Any help would be appreciated.

  These suggestions have worked. Thank you.