Offer by ricambio alimentatore PowerVault MD1000 [GRO]

Similar Questions

• PowerVault MD1000 Perc 6/E hot swap

  Which would prevent me from doing a Hot Swap on a 136GB 15K SAS drive on a PowerVault MD1000 with a Controller PERC 6/E for Adaptive Read Ahead, write new policy, broadband strategy of disk, RAID-10 in degraded state, a defective disk cache 64 KB, disabled?

  Blew up a car and you want to make sure I can hot swap on this machine. I read through product docs, but you are looking for something extra that I want to check that I missed on. Server of our warranty and support from last year. Everything I see is green lighted to go, but I always want to get will as many resources as possible before blowing a RAID 10 potentially because a controller had some setting that prevents a switchable good hot to rebuild. Make backups before swap, swap during off-peak hours doing rebuild starts on commercial operations.

  I read through docs:

  http://public.support.Unisys.com/pcproducts/ESX/docs/DellDocs5.4/en/Perc6i_6e/chapterb.htm

  http://support.Dell.com/support/eDOCS/systems/MD1000/en/Hom/om_en.PDF

  http://support.Dell.com/support/eDOCS/systems/MD1000/en/supmatrx/Feb08update/md1000_SupportMatrix.PDF

  Hello matt.newman,

  For the MD1000, you can replace a failed during execution of the MD1000 drive.  When you insert the replacement drive, it will start a reconstruction.

  To replace the Perc6 you will need to do is the following:

  1. Make sure you have a good backup tested all the MD data
  2. Turn off the server and the MD
  3. The PERC6. Remove and replace
  4. Turn on the MD & wait that he move to a ready state
  5. Turn the server & go in the new Bios Perc6 / configuration
  6. You have to re-create the raid10 & together for Adaptive Read Ahead, political writing back, broadband 64 KB, off the disk cache strategy
  7. Once you have created the raid then leave the PERC6 configuration utility and the Server post to the operating system
  8. Once logged on the operating system you can then run the restore to restore your data to the MD

  Please let us know if you have any other questions.

• PowerVault MD1000: Attached directly slow to copy the data from storage.

  Hi all

  I have a powervault MD1000 attached to a PE2900 using scsi. When I write for the PV everything is ok, but when I want to read it, for example copying the data from it, he grinds the server stops and usually falls!

  can someone advice could be what the problem?

  
  

• Can I extend the matrix raid in PowerVault MD1000 with Perc 6/E adapter?

  I created raid0 with 2 HDD. How can I add another hard disk to a previously created table?

  I'm running a few commands

  sudo. / omconfig storage vdisk = action reconfigure controller 0 vdisk = raid 0 = r0 = pdisk1:0:0, 1:0:1, 1:0:2

  sudo. / omconfig storage vdisk = action reconfigure = 0 = raid 0 = r0 pdisk1:0:0 vdisk controller, 1:0:1: 1:0:2 vdcapacityexpansion = yes sizeinpercent = 100

  result: operation disabed. How can I solve this problem? active web interface there is no command like reconfigures

  

• MD1000 stato crítico [MS]

  Buongiorno,

  Abbiamo UN PE2950 + MD1000 da UN client in uno stato anomalo:

  MD1000 ha 8 brain in raid 5 + 1 HS e allo stato current it disco 13 e in rebuilding allo 0% da 2 giorni e it disco 14 e predicted failure

  PE2950 vede non piu lo e storage it client e fermo.

  Come we can rate per avere una diagnosi di UN tecnico Dell + preventivo per assistenza?

  Thank you, good day

  Salve,

  Offerta inviata per diagnosi Telefónica su Powervault MD1000 storage, offer: offer Dell n ° 15469269 client: IT2008940 - ANDRA SPA

  Speaking saluti

  Manual

• Disco guasto MD3000i [GRO]

  Buongiorno,

  HO a disco guasto knew UN MD3000i serial number: 3XC4M3J.

  richiedo offer by ricambio.

  Grazie

  Buongiorno, vedo slab our journal internal che he solved, it could confermarlo e caso?

  Grazie

  Marco

• MD1000 password reset?

  My employer has recently acquired 2 powervault MD1000s and it is my job to restore the default values for sale. I just got the password reset cable, but I can't find any documentation pertaining to orders or any other reference in the manuals or online. What should I do to clear the passwords and reset these default units? The source of these units is a large University who refuse to divulge any information, and I do not have a contract of Dell of any kind. Support Dell will help? I have all of the options have here? Any input appreciated.

  B

  Hello bahauser,

  On an MD1000 configurations are preserved on a PERC card that is attached to the server as a PERC 5 or 6 PERC.  So if you get a PERC card then all you need to do is hit CTRL + R & who get up in the boot controller card when it checks all the expansion cards & happens to PERC.  Once in the bios the card controller, then you can go to the leadership of VD & remove all virtual disks.  Also, you only need the cable to reset password for an MD3000 or unit higher.  Is there a MD3000 & the MD1000 is attached to it?

  Please let us know if you have any other questions.

• MD1000 unified Mode and 2 Active Directory servers

  Hi all, I'm no expert with the servers, but I get by well enough.

  I currently have 2 identical servers poweredge 2950

  One is a server to the server's active directory master windows 2012 and the other is the same, but the slave of the mirror.

  I have a Powervault MD1000 connected to the master ActiveDirectory controller, but I thought to myself, not to award good people being able to connect on the backup to secondary, they cannot access the md1000 where all their files.

  Then question, I currently have the MD1000 unified mode. Is it possible to connect the other server until the other side or anywhere elsewhere that it is also showing on the slave?

  That way if the PDC goes down, people can still connect and access their files on the MD1000.

  I hope that all the senses.

  If not, does anyone have a suggestion for how they would accomplish this?

  This is not an option with a MD1000. Do you need raid controllers that communicate with eachother, that is not an option with the PERC5E/6th/800/810.

  Shared storage that you have in mind requires specific hardware and some software.

  For hardware, you would need a SAN as a MD3000 and could then set the MD1000 to the MD3000 (this assumes you have Dell certified discs (the MD1000 does not require this, but the MD3000 does)).

  With regard to the software; you would have to set up a cluster, which should really be done with ad servers (but the servers need to be joined to an ad).

• Moving Raid drives Bad Phy Slot

  I need someone to tell me if my approach is correct.  We have a Poweredge 2950 connected to an Powervault MD1000 with a bad location.  We have an another Powervault MD1000 that we'll use to replace it.  Since it is the same model table, what have we to do to transfer the readers to the new table?  I think we should be able to server and storage, disconnect the table, remove current disks, place them in the same dwelling in the new table that they are in the Bay broke, connect the new table, and then restart.  Is this correct?

  Hello hhertz,

  Yes, the way you put out is the correct way to get your readers to your MD in MD again.  When you turn on the server I would check in the PERC bios to make sure that all the drives are online and seen as it should.

  Please let us know if you have any other questions.

• initializing virtual disks

  I have a powervault MD1000 (Bay raid storage) connected to a backup server. It is set up with 3 virtual drives that each use 2 terabytes of storage in RAID 5 from our range of 8 physical disks.

  I had to replace two of the physical drives, and I need to initialize my virtual disks. In the Perc 6/E management screen VD, I can select the virtual disks (that show in red) and press F2 to display the operations, but the initialization button is dimmed and I can't select it. In the PD management screen, the new drives show as ready.

  How do I initialize my virtual drives? Should I delete them and create new virtual disks? It's my first time doing this, so please bear with me. Any help would be appreciated.

  I just updated the firmware of the 6th Perc to version 6.3.3 - 0002, which has a rep to support Dell recommended that I do, if this is useful.

  After you remove virtual drives, I was able to create a new virtual disk and initialize it. It seems that I just have to build the virtual disks from scratch.

  Thank you for your time.

• VM connection to an external storage array

  Hello everyone

  Has anyone connected a virtual machine to an external array as a Powervault MD1000 external storage array?

  Reference Dell MD1000

  http://www.Dell.com/content/products/ProductDetails.aspx/pvaul_md1000?c=us & l = in & s = BSD & CS = 04

  Hello

  You can either use a VMDK created on the MD1000, or you can use http://itknowledgeexchange.techtarget.com/virtualization-pro/vmware-esx-storage-how-to-get-local-storage-to-act-as-a-raw-disk-for-vms/ as instructions to do what you want to do.

  Best regards
  Edward L. Haletky
  VMware communities user moderator, VMware vExpert 2009
  ====
  Author of the book ' VMWare ESX Server in the enterprise: planning and securing virtualization servers, Copyright 2008 Pearson Education.
  Blue gears and SearchVMware Pro items - top of page links of security virtualization - Security Virtualization Round Table Podcast

• PowerVault MD3000 to swap MD1000 controller card possible?

  Hi all

  We have a few MD3000s end of LIFE that we want to reuse for other purposes. Is it possible to simply replace the MD3000 with ones MD1000 controller card and assign a MD1000 essentially? The reason why we must do, it is because we can buy the slower red Western Digital disks that will work for our needs and with the MD3000 we are locked into buying Dell brand readers. I understand that we need a perc 5 or 6 card as well.

  Thanks for the help

  Sorry for the delay, the JT517 is the most recent part number. These are the same just part the JT517 is a more recent reference number and it was used to replace HN240.

• Ricambio by R710 [GRO]

  Buongiorno,

  VI chiedo cortese offerta e tempi di delivery by alimentatore del Server R710 tag 9ZCQJ4J.

  Grazie

  Saluti

  Buongiorno,

  Con passing it mouse sopra identifier c Supporto Dell'e the voce "private message", it could mandarmi come message privato di seguito required information?

  By the spedizione (intervento o):

  1. company name:

  2 address:

  3 City:

  4 Provincia:

  5 cap:

  6 name/last name/number phone/e-mail del referent in loco:

  With the fatturazione

  1 nome società (o codice client o number order recent):

  Address 2:

  3 City:

  4 Provincia:

  Heading 5:

  Name/last name/number 6 telephone/e-mail del referent by the fatturazione:

  7 partita IVA

  Speaking saluti

  Fabrizio

• Management Dell Powervault 220 s of Poweredge 2950

  Hi all

  I am new to the forum and would be very happy for any advice you could offer.

  I'm looking to re-purpose some old material for WDS. We have an older PE2950 I would use, as well as a Powervault 220 s that would be used for storing images.

  Now, I know there are many messages from forum on this subject, but I feel that I may have a unique situation, since only add-in cards I have to interface with the PV are HP SC11Xe.

  I guess my first question here is that will work? After installing the card, I can see readers in the PV during startup and they appear even in the management of the computer, but I can't do anything with the volume.

  We are not looking to dump a lot of money in this server, because it is quite old. We are mainly looking to move away from a WDS VM running on a Mac Mini Server, and I thought this might be a better option.

  We have an old server that was originally set to run the PV; a PE1850, but the specifications are not acceptable.

  For what it's worth, the PV was originally created as a split volume.

  Hello, cameron.tropser.

  First of all, I can say that the HP SC11Xe won't work with Dell Open Manage Server Administrator (OMSA). You have two options: boot in the BIOS HP controller and configure from there or use the controller inside the PE1850 (?).

  If this was used originally with the PD1850, then the config is likely, always on this controller.

  Beyond that, you won't be able to configure/manipulate volumes via OMSA.

  I hope it's useful.

• PowerVault NX3100 drive failure

  Hello

  We have a problem of drive on a PowerVault NX3100 server failure.

  SAS

  HARD DRIVE

  136,12 GB

  Dell (TM)

  ST9146803SS

  FS62

  6SD17KY7

  We need an offer for a spare part.

  Best regards

  Buongiorno, the sto contattando via e-mail