old PC, new monitor display problems

Similar Questions

• Document windows does not use all the available on new monitor display area

  Hello

  I have a new monitor - a Benq BL2711.

  I have set up as my secondary monitor on display in Windows 8.

  I can put Photoshop (CS6) on this screen and maximize the it, but there is a vast space not used in the document window, which is not used. I want to show a lot more of my images that I can currently, but the document window will not only fill all that screen real estate. A large part of it is lost.

  The panels occupy the right space to the bottom of the screen, but the window of the document (or the display area?) uses only 60% of the height of the screen.

  What is a limitation or do I have to configure something? (I have reset the workspace of photography).

  Thanks for any help

  Nick

  It is really a shot in the water, but it's the space used by the "timeline" Panel when it is open. Try to check in the menu window and close the bottle.

  Other that that, there are always some good old Reset preferences. Make sure you save the custom actions/brushes/presets and so forth first!

  

• New monitor displays an Error Message "Signal out of range" when computer starts

  Installed new ASUS VS24H-P control on my computer and I get this image of "out of range" bouncing around the corners of the screen.

  This means that the computer sends a signal that the monitor is not capable of displaying.  It could be:

  • A screen resolution (width x height pixel size) is selected, the monitor cannot display
  • The refresh rate (Hz) is the one who can not display the monitor
  • These two

  If you have another monitor, you can plug it to visit your office. Right-click and choose the resolution of the screen, then turn it down to a 'safe' resolution like 1024 x 768 (most monitors can display this).  Then plug your new monitor back and turn the resolution back to a better suited for this monitor.

• External monitor display problems with Dynadock U10 on PC Toshiba laptop Win7

  I just started with my current compnay and they allocated me a new from Toshiba Satallite laptop running with Windows 7 64 - bit operating System.

  They hooked me up a Station of reception Dynadock U10, separate keyboard and a mouse and a monitor external 22 ".
  I experienced a problem of compatibility with some software, but I currently have a major problem with slow internet pages freezing or general display issue when the VGA is connected to the docking station.

  The laptop works fine when the VGA is connected directly to the laptop. I have download the recent software/driver upgrade loaded 18 (TC30322400A) without fixing the problem.

  I also loaded the upgrade diplaylink 5.6.31548.exe, as mentioned in other forums, once again, without success.

  Any help would be appreciated.

  Alex

  Are you using the latest driver?
  In my opinion you should not update BIOS.

• monitor display problem - says he will sleep when it is turned on.

  Problem: the original title screen

  Turning on my computer - screen trying to start up then he said monitoring sleep - he brought once but the screen was skewed.  my monitor is fine - I have it plugged into another computer and it works fine.  would it be a virus or a video card?  should I try to hit the f8 key during startup to go to safe mode or just take it to the computer store?

  Hello

  · What is the number and model of the monitor?

  · Do you remember all the recent changes on the computer before the show?

  · What is the service pack installed on the computer?

  · Have you defined a plan of the power on the computer?

  Check the status of the graphics device in Device Manager. Follow the steps for the same thing:

  a. click on start

  b. click Run, in the Run dialog box type devmgmt.msc

  c. in the Device Manager window, locate the video drive and expand the drive, double-click the sub element to check if an error message or error code is listed.

• 700 AIO monitor display problems

  I got a Lenovo Ideacentre AIO 700 for Christmas and once through the initial updates after a black screen reboot, when I connect it to my TV it will go through my tv, but no more detects any other screen, how can I go back on the screen of computers?

  In response to customer relationships of the black screens intermittent when the 700-24ISH AIO devices are turned on, Lenovo comes from Lenovo IdeaCentre AIO 700 scalar fonts improved Firmware to solve this problem.

  The CONSULTING Service is available here: https://support.lenovo.com/us/en/documents/SF16-I0006

  The firmware can be downloaded here: http://support.lenovo.com/us/en/downloads/ds111714

  Thank you

• Monitor display problems

  Hello

  I was using my laptop (Dell Inspiron 1720), and somehow I pressed a few buttons that transformed my horizontal office on the screen. How can I fix it.

  Mozartman

  Try to press Ctrl + Alt + up ARROW, or try Ctrl + Alt + and a different key to the arrow.

  If this does not work: right click on the blank desktop-> Graphics Options-> Rotation.

  I hope I could help

• Problems connecting to a projector. Laptop recognizes the new monitor but projector does not display anything.

  I have a Macbook Pro (non-retina display) mid-2012. I have a mini VGA screen that worked throughout the year and all of a sudden, it doesn't seem to work. My computer recognizes the new monitor (screen flickers and flies all content secondary screen) but the projector does not display anything. I tried to reconnect the cable, the cable VGA switch to turn on the projector and turn off, restart my computer and clouds of dust on the connections. Sometimes if I move the connection just that will work, but if I so much as breathe on it or watch funny it stops and I can't get it back.

  Jiggle the cable or adapter is something different, you have a physical adapter or cable problem. Any bit-reversal can help that.

• New monitor will display not all resolutions

  Recently bought a new HP monitor # 2210 m, and am running HP Media center m7334n Desktop, Windows XP sp3, ram 2 GB, 2.0 G cpu.

  Problem: that's like half of the resolutions listed in the monitor sheet (there are 11 presets).
  I want to put it in 1280 x 768, but it is not listed as a choice in the display properties.

  I lost several hours with HP technical support (Overseas), and their final decision was that the computer is too old (5 years) to support the new monitor. After I hung up, I realized that the monitor has been able to run on its native resolution of 1920 X 1080. So, how is it not possible to run at a lower resolution?

  Graphics are integrated on the motherboard, so I can't find care about resolution so that it doesn't matter where.
  I've updated the graphics driver and the driver for the monitor.
  I uninstalled the driver for the monitor, computer rebooted, everything is recognized, without yellow exclamation, but still no option for the setting of 1280 X 768.

  How can I get the monitor to display the resolution that it is capable of?

  Thanks for your help

  o.k.

  all tracks have been explored and exhausted.

  the integrated graphics card & monitor drivers have been updated.

  the desired resolution does not always appear in the display properties or the available ATI ads.

  I go to the idea that this particular resolution (1280 x 720) only is simply not supported by the graphics card.

  Thank you for your time & assistance

• Hi I have a new monitor but when I turn it on it turns on but then disappears and the middle of it, he says display something cannot get the video mode so u can help me change

  Hello

  My name is Karen, I just got a new monitor used, but when you turn it on, it turns on, but then you can't see something that he disappeared and in the middle of the screen it says u can not display this video mode, your help would be great thanks.

  Hi Karen,.

  Welcome to the Microsoft community. According to the description, you are not able to get the display on the monitor.

  ·         What is the full error message?

  I'll help you with this problem. I suggest you follow the steps in the article.

  Troubleshoot monitor and video card

  I hope this helps. Let us know if you need help with Windows related issues. We will be happy to help you.

• Problem with new monitor when you play Cityville

  Recently installed new monitor (HP2511x), now the zoom in/out function does not work in Cityville.  It works very well to Farmville, and it still works in Cityville on my laptop, so it's something on the new monitor.  Any ideas?

  It sems to be a chip on board:
  http://en.Wikipedia.org/wiki/GeForce_6_Series#GeForce_6150SE

  You have no problem with your old monitor?
  Did you use another resolution (bottom) with the old?
  You can try to fix this old resolution for your new monitor, too.

  Then there should be no problem for your graphics chip.

  HTH
  C.

• Problem with new monitor

  Hello

  Since I bought a new monitor (Phoenix G Gold - Master GB2888UHSU - B1 of iiyama, resolution of 3840 x 2160) I have a problem when working with lightroom. As you can see, the photos are just screwed up. When I Zoom in on the photos, it's ok.

  

  On my old monitor (BenQ GL2450H, resolution 1920 x 1080), it works fine.

  

  My system:

  OS - 64 bit Win10

  graph - ASUS Geforce GTX1080

  CPU - i7 - 6700K

  RAM - 16 GB

  Version of Lightroom - 6.7

  Win10 and hardware drivers are updated.

  I tried to reinstall lightroom, but no change.

  Is there a solution for this problem?

  Thank you.

  Concerning

  Tobias

  As a first step of troubleshooting, uncheck the option preferences > performance > CPU graph use.  Who help me?

• I have an old Mac Mini with a DVI Port that came with a VGA DVI-adapter.  Tonight, my monitor went down.  Brand new monitor works with that?  Can I use an adapter?  If yes should which adapter I?

  I have an old Mac Mini with a DVI Port that came with a VGA DVI-adapter.  Tonight, my monitor went down.  Brand new monitor works with that? Any recommendations? Can I use an adapter?  If yes should which adapter I?

  You can use any DVI monitor DVI port directly or have any VGA monitor with the power that you adapter. A HDMI monitor might work with an adapter DVI to HDMI in a pinch, but HDMI tends to be more fickle.

• There seems to be a display problem. Please check that your monitor is HDCP and is not mirrored by using Airplay.

  There seems to be a display problem. Please check that your monitor is HDCP and is not mirrored by using Airplay.

  Apparently, you're trying to use AirPlay to display content that is protected in a way that not only allows the copy.

• HP computer laptop-15-be002tu: display in a new laptop screen problem

  Dear friends,

  I bought a new laptop from hp [hp-15-be002tu]. It is provided with the operating system of back free v.2.

  When I tried to start my laptop by pressing power button there is no display on the screen. But I waited for 5 minutes. The HDD & dvd player work properly.

  But I noticed screen does not work. How can I solve my problem?

  Please give good soggestions to fix my problem

  Thank you all

  Dear friends,

  My display problem has been resolved.                                                                                                                                                                         An HP service technician visited my house [on-site warranty] and inspected my computer hp laptop and found that a video cable from the lcd screen was not correctly set. This is why there is no display on the screen of my computer hp laptop.

  I asked him why he came... It is due to either by transportation [services of e-mail... etc.] or manufacturing unit.

  In any case, my problem has been resolved.

  Thanks for the HP amicable services team

  M.Ganesh kumar