Optical USB mouse problem with Portege R100 on windows XP
We have three laptops Toshiba Portege R100 currently giving problems with mouse optical usb from Toshiba.
When starting the laptop, that the mouse is not recognized by windows. Before and after will be identified in the mouse will not respond while Burns led.
The mouse will be recognized after re - plug in the USB port.
We have updated versions of bios to the latest version. (1.4)
Another mouse (USB optical) works OK without problem.
We have removed the drivers and reinstalled by windows plug-and-play process, but it does not work.
Is this a known issue?
Thanks in advance
would it be possible that the USB mouse has high power consumption?
As far as I know, there are a load of maximum intensity for each USB Port.
Do you know how much power (intensity) needs to this mouse?
Finally a solution for the problem with the R100 SD card reader.
(I found someone with a working one, then I copied their)
the driver is
Microsoft sdbus.sys 20002 6.0.4069.5
NO Toshiba 2003
(no my working version had scsi for a reason any)
Thanks for the info that you could solve this problem by using a different SD card reader driver.
I have two laptops which, without reason, all of a sudden loses connectivity of bluetooth mouse, it just stopped working and then I have to reboot to get it working again. Two of these computers also have a bluetooth keyboard that is not assigned, the mouse. I don't find anything wrong with bluetooth and have tried several different mice with the same results. Windows 7 ultimate on two laptops. a laptop computer used to run vista ultimate with the same mouse windows and it never happened, it started with windows 7.
These used laptops are relatively very close where they can interfere with each other?
Will there be electrical/electronic or other types of interference in the region?
Check with the bluetooth device to the manufacturer for known issues and possible solutions
Visit the Microsoft Solution Center and antivirus security for resources and tools to keep your PC safe and healthy. If you have problems with the installation of the update itself, visit the Microsoft Update Support for resources and tools to keep your PC updated with the latest updates.
Norton and other security/antivirus/antispyware programs are known to cause problems with
It is extremely difficult to solve the intermittent problems.
Hardware devices not detected or does not work - a Mr Fixit
The problems with Bluetooth devices
Set up a Bluetooth compatible device
The problems with Bluetooth devices
How to set up a Bluetooth connection
The Bluetooth item in Control Panel on a Windows Vista SP2 computer does not
as expected when you click on the element - for Windows 7 this check manually
If you need drivers try the support site for the manufacturer of your system and/or the site of the manufacturer of the real device.
BluetoothView is a small utility that runs in the background and monitor the activity of Bluetooth technology
devices around you. For each detected Bluetooth device, it displays the following information:
The device name, address Bluetooth, Major Device Type, minor device Type, first detection time,
Last detection time and more. BluetoothView can also warn when a new Bluetooth device
is detected, by displaying a balloon in your bar tasks or playing a little beep. -FREE
BluetoothCL is a small console application that transforms all differential of bluetooth devices detected in
the standard output. For each Bluetooth device, the following information is displayed: MAC
Address, name, Major Device Type, minor device Type and possibly the name of the company of
the device (if the external file of MAC addresses - oui.txt is provided) - FREE
Add a Bluetooth device to your computer
Add a Bluetooth device or other wireless or network device: frequently asked questions
More information of possible interest to some: (not directly related to this issue)
What is a Bluetooth personal area network (PAN) network?
Connect to a Bluetooth personal area network (PAN) network
I hope this helps.
Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.
I ve you have a problem with my laptop.
I would like to install Windows XP SP2 instead of Vista, but I had a problem with the hard drive,
Windows XP Installer cannot find the hard drive. It is problem with drivers disk, but the site of tohsiba I can´t find my laptop and the disk for XP drivers.
Can someone help me?
Maybe I can use drivers from another laptop A200 series, but which?
a good explanation how to install XP on a SATA machine can be found here:
Welcome and good luck
problem with babylon runing on windows 8-storage initialization failed (error 10)
1. when exactly you get the error message?
2. do you have an error message?
3. are install you authentic version of Babylon?
This issue would have occurred due to some third-party programs, the origin of the problem. I suggest you perform the clean boot. Clean boot helps eliminate conflicts of software that occur when you install a program or an update or when you run a program in Windows. You can also troubleshoot or determine what conflict is causing the problem by performing a clean boot.
How to perform a clean boot in Windows
Note: Follow How to reset the computer to start as usual after a clean boot troubleshooting article KB929135 to reset the computer in normal mode.
If the problem only occurs with babylon click here to send a request to the Babylon 8 support team.
Post us the results after trying the steps above.
I can't add youtube video on my site (Muse response: there is a problem with the program and windows stops)
Use the command search at the top of this page or follow this link: YouTube embedding continues to crash the app.
I have problems with photoshop cc in windows 10. I am not sure if the problems are related to what windows 19, but certainly, the problems got worse since. (My computer runs on windows 10. At an i7 processor, NVIDIA® GeForce® GTX 965 M, the DDR3L 16 gig memory, the GDDR5 2 GB graphics card, a card of 256 GB ssd and 1 TB of hard drive). I don't think it's a problem with my computer.
I am currently working on a project where I need to cut some parts of the photo, that I will use it later. But I'm having the problem now, some photos displayed as it should. And some are not. They seem to be grey. Or there is some kind of white/gray block above them. It is as if is not available to the loading screen (?). If the object is there, but just does not appear right. I just put a few screenshots here that show the problem. I hope someone can help me with this. Because I can't finish my project with a photoshop which does not work at height.
I really hope that anyone kno w s, what the problem is and can help!
This seems to be a graphics card problem.
Please disable the graphics processor in photoshop, and then try again.
Click on edit-> preferences-> Performance
Uncheck use graphics processor
Close Photoshop and re - open and then use the way you did that.
Also, please share the exact version of your Photoshop.
can anyone help
I have a problem with photshop cc on windows 8.1 and 4 k display to a resolution of 3840 x 2160 when I launch photoshop cc, everything is very small and I don't know how to get the program to the right size
Install Photoshop CC 2014 and turn on the preference of the user interface scaled by 200%.
I recently bought a used Portege R100. It came without OS and I wanted to install XP SP2.
I know that restorations only work with PCMCIA readers adapted, but the HARD drive is formatted, so there is no recovery possible I guess.
Here are my problems:
-with my very old Freecom PCMCIA CD player the Windows installation CD is recognized, and it starts to load the XP drivers until he wants to start copying files installiation--> then I get the blue screen of Windows with the error 00 x 7 (virus or driver)
-the same thing happens with my former W2k Pro installation disc.
-With the even more ancient W98SE, strange things are happening too: installation seems to work fine, but when it comes to start with W98SE, for the first time, the system hangs up with pixelgarbage.
-Make the 6 Bootdisks with makeboot doesn't work anymore.
-J' also tried MS-DOS! And guess what! It worked! Loading the Freecom drivers and copy of Windows I386 folder on my hard drive with the volkov Commander (something similar to NortonCommander) worked too! So I got hav files on my drive but after running Windows NT in the i386 folder, the system hangs after some time, when it starts to copy the files to a temporary folder.
So I tried almost everything I know. at this moment I am download knoppix to try it.
I ran Memtest86 and 9 Diskmanager to test the RAM and HARD drive, finished two withut errors, so the priority of main parts in the installation process seems to work. Maybe it's that my IDE controller is broken?
I have no idea, WHY does he not move windows!
Help is hot!
It should work out that way, run you own your HD first in Fat32format - file-system, otherwise it won't work!
Don't forget to use "smartdrive' in your BACK-commissioning, otherwise it will take a lot of time, even the 'freeze' is possible.
See also: http://forums.computers.toshiba-europe.com/forums/thread.jspa?threadID=19232
The mouse to my PC has just randomly stopped working. I connect it to the PC and I get an error indicating that the driver could not be installed. I went to Windows Update and tried to install "Microsoft - pointing drawing - Microsoft USB Mouse Hardware", but failed. Then I went into the properties of the pilot of the aircraft and tried to update, but I got an error saying "access denied." I uninstalled my anti-virus software and disabled the Windows Firewall to see if it would solve all conflicts, but nothing worked :/ I also tried 3 other mouse on the computer but the same errors with each.
Any help would be appreciated
Thanks for posting your question on the forum of the Microsoft community.
I appreciate your efforts to resolve the issue.
I would like to know some information about the problem so that we can help you better.
Have you made any changes to your computer hardware or software?
I would suggest trying the following methods and check if it helps.
Run this Microsoft fixit and check.
Hardware devices do not work or are not detected in Windows
If this does not help, then use method 2.
Please use the suggestions contained in this Microsoft support article and check the issue.
Mouse, touchpad and keyboard with Windows problems
See also the suggestions highlighted by Niki Han Moderator on November 7, 2011 and mark as answer.
I hope this information helps.
Please let us know if you need more help.
Randomly, after the Windows 7 login Panel, windows disables my keyboard and USB mouse.
-No problem in BIOS or on the login Panel, but once the credentials entered and valid, and reaching office, mouse and keyboard (USB) close
-To solve the problem, I need to reboot several times, waiting for an instance where my devices are not closed (so it works without any pb until the next reboot)
-J' have a backlit keyboard and when the problem occurs, light are turned market, as if it was turned on and turned off randomy
Searching the Internet, seems, I'm not the only to encounter the problem, however single chip found Advisor on these was mentioning it is a bug in Microsoft Windows 7, associated with the management of the power supply of the USB ports. However the advice provided to change the config to disable these judgments do not work...
Thanks in advance for your help and best regards
Have you tried to go to safe mode with networking Mode and update your USB drivers?
You didn't say you had the problem goes mode without failure, so it might be a solution for you.
USB drivers should be found at the web page of the manufacturer of your computer or your motherboard manufacturer's web page.
I have a portege R100, which, with the new 1 GB memory is very good. I want to update from XP to Win7.
All the world does? Any suggestion? Win 7 slow down the system?
If I undestand you, you have only 1 GB of memory? If you do, I'm sorry, but your system would be slow as hell. 2 GB is a minimum in my opinion.
The last time using my my computer windows 7 I can't move the windows. (I use every day because it is mainly for my work/accounting. Just now not a lot of work). Any time, I take the upper edge with my mouse it fills the entire screen. I try again and again same problem finally, that I get it until the next time. When I try to resize anything happens. Then when you use Word, I click on round top of page logo for print or save etc. He left the program.
I will try the solution proposed here to shoot trouble the mouse too. It's an old Logitech wireless with a docking station.
Most of the time I use my computer with Vista Ultimate.
It is clear that double click occurred sometimes when you use the left button of the mouse.
First of all, in Control Panel / mouse properties trying to adjust the speed of the double click on the tab buttons. If the problem persists, try a different mouse. This problem is sometimes a hardware problem with the mouse itself.
I try to install Windows 8 in my computer, and this message is returned:
Your PC needs to be repaired
The Boot Configuration data file is missing some required information
error code: 0 * c0000034
You will need to use tools of recovery on your installation media. If you don't have any facility (such as a disc or USB device) support, contact you system administrator or the PC manufacturer.
Press ESC for UEFI firmware settings.
Please, I need help. Thank you
Thanks for posting your query in Microsoft Community.
I understand that you receive this error message during the installation of Windows 8 and I'll be happy to answer your query. Let me ask you;
- How you try to install Windows 8?
- You have the installation media (DVD/USB)?
- Why the type of installation you are performing?
- Why do you want to install Windows 8?
- What operating system is installed on the computer currently?
According to the guidelines of the error, it seems that you are trying to refresh or Reset. However, since you get this error, it appears that you do not support installation to complete the process.
You can create the installation media for Windows 8 with the following steps:
When you are prompted to run or save the file, choose run
When you are prompted to enter a product key, enter the 25-character product key, that you received when you purchased Windows 8.
When you are prompted to install Windows 8, select install by creating media and then click Next.
Select the type of media you want to use: either a Flash DRIVE or a DVD.
To create a USB flash drive
Click on the USB flash drive.
Plug the USB key into a USB port on your PC.
When you are prompted, select the USB key that you want to use, and then click Next.
If you have files on the USB flash drive, it will remove them.
To create a DVD
Click on the ISO file , and then select the location where to save the ISO file.
Insert a blank recordable DVD into your DVD drive.
Burn the ISO of the DVD file using Windows disc Image burner, or another program DVD burning.
Important: If you have any Windows 8 product key, you cannot create installation media. Make this DVD or USB flash drive that you use has nothing else stored on it and has a sufficient free space to download the Windows 8 Setup: approximately 1.8 GB for the 32-bit version and about 2.3 GB for the 64-bit version.
Hope this information is useful. Please feel free to answer in the case where you are facing in the future other problems with Windows.
I use a HP Pavilion dm4 with a Synpatics PS/2 port touchpad.
I look down.
I had a new upgrade to Windows 8 Pro and had installed the Synaptics touchpad drivers.
At the beginning, that it worked well. I had use of all the features like the shots of border and multitouch gestures
That lasted only a few days, however, how she returned to regular feature where the only thing I had was available to scroll. It seemed back in the functionality of the Windows 7 driver.
And, whenever I tried to use the Synaptics control center it tells me that it cannot find that a connected Synaptics touchpad, which is strange, because it is without a doubt detected by Windows as the touchpad as I a see in Device Manager.
The exact message is "If you have installed another PS/2 pointing device driver, please uninstall the synaptics driver by clicking on the Yes button. You must then reinstall your device pointing to your external device driver again. "It makes no sense, because I certainly have not connected an external device. The uninstall does not work - see the following.
I tried the following:
- I went to the Device Manager and tried to update drivers touchpad there... nothing helps, of course. He said that my version was up-to-date.
- I tried to reinstall the driver. If I uninstall the driver, he invites me to restart the computer... the problem is that when I did it and the computer has restarted, or the keyboard or the touchpad responded. I had to do a system restore to be able to use again.
What is a solution for this? I'm kinda stuck. I can try to do a refresh as soon as I have my installation media but I won't for awhile.
We had the same problem with a Compaq laptop.
Windows Update has updated the synaptics driver with a version that not working with shots.
I removed this driver and had no toutchpad and keyboard work.
With a mouse, I could use the screen keyboard on (someware sits on the lockscreen) and I was able to reinstall the hp synaptics driver.
I put the update driver in hidden Windows update Department. Don't remember how exactaly.
Maybe you are looking for
Hello My Macbook Pro: When I start my Macbook Pro, I can hear the volume of the speakers to boot. After the start of the Mac, the volume control is completely disabled and cannot be controlled. But when I plug my headphones his license. Is there a se
Hello I recently bought and installed the printer wireless HP Photosmart 5520. I have a combination of Android and iOS devices in my house. I installed HP ePrint App on both of them. With Android tablet the printer works fine. However, my wife cannot
XP sp3 system.Repeat attempts - no joy.informed suggestions please? & thanku!
j got a probler with messenger can I may my webcam its not rated mash it Mayenne error?
I CAN'T DOWNLOAD VIDEOS FROM A CANON FS 200 CAMERA IN MOVIE MAKER. WHAT I GET IS A BOX SAYING THAT IT DOES NOT DETECT A DEVICE. HOW CAN I DO THIS