Out of the frame of the output

Similar Questions

• .. TV picture jumps out of the frame

  When minimizing Media Center tv, the picture is going out of the frame.  I can hear, but not see.

  Enlarged photo is correct, but covers the entire frame.  It worked fine until a few days ago.

  Update your graphics card driver.
  Visit the manufacturer's Web site to download and install the latest graphics driver. Once done, check again the issue.

• How stop the audio when I get out of the frame AS 3?

  Hello

  Could someone find out how to stop the audio when I get out of the AS 3 mounting frame? I had around 20 slides running in a swf file. Each slide has the distinct voice on attached to it. I added slides in a layer and voice in the next layer on the timeline.

  Ago next and previous buttons placed throughout this swf to navigate between slides. This is where the question arises. I can travel easily from 1 to 20 slides and even can return trip. But the voice does not stop as soon as I click on the previous or next buttons. It overlaps with the next or previous voice just above.

  I searched online and suggested its use as channel to bring voices on the slides to have a better control. But honestly I don't know how to do. Could someone help me in doing this? This problem can be very simple for others. As I am a beginner in Flash and Actionscript, it hurts.

  Carry me nicely, if this code seems to be bit annoying and even lenthy :-(

  Thanks in advance.

  Code:

  Forward_Button.addEventListener (MouseEvent.CLICK, forward);

  Previous_Button.addEventListener (MouseEvent.CLICK, prev);

  function forward(event:MouseEvent) {}

  if(this.currentFrame == This.totalFrames) {}

  Stop();

  }

  ElseIf (this.currentFrame > = 55 & & this.currentFrame < 201) {}

  gotoAndPlay (201);

  }

  ElseIf (this.currentFrame > = 201 & & this.currentFrame < 310) {}

  gotoAndPlay (310);

  }

  ElseIf (this.currentFrame > = 310 & & this.currentFrame < 430) {}

  gotoAndPlay (430);

  }

  ElseIf (this.currentFrame > = 430 & & this.currentFrame < 530) {}

  gotoAndPlay (530);

  }

  ElseIf (this.currentFrame > = 530 & & this.currentFrame < 640) {}

  gotoAndPlay (640);

  }

  ElseIf (this.currentFrame > = 640 & & this.currentFrame < 750) {}

  gotoAndPlay (750);

  }

  ElseIf (this.currentFrame > = 750 & & this.currentFrame < 860) {}

  gotoAndPlay (860);

  }

  ElseIf (this.currentFrame > = 860 & & this.currentFrame < 970) {}

  gotoAndPlay (970);

  }

  ElseIf (this.currentFrame > = 970 & & this.currentFrame < 1080) {}

  gotoAndPlay (1080);

  }

  ElseIf (this.currentFrame > = 1080 & & this.currentFrame < 1200) {}

  gotoAndPlay (1200);

  }

  ElseIf (this.currentFrame > = 1200 & & this.currentFrame < 1310) {}

  gotoAndPlay (1310);

  }

  ElseIf (this.currentFrame > = 1310 & & this.currentFrame < 1420) {}

  gotoAndPlay (1420);

  }

  ElseIf (this.currentFrame > = 1420 & & this.currentFrame < 1530) {}

  gotoAndPlay (1530);

  }

  ElseIf (this.currentFrame > = 1530 & & this.currentFrame < 1690) {}

  gotoAndPlay (1690);

  }

  ElseIf (this.currentFrame > = 1690 & & this.currentFrame < 1780) {}

  gotoAndPlay (1780);

  }

  ElseIf (this.currentFrame > = 1780 & & this.currentFrame < 1880) {}

  gotoAndPlay (1880);

  }

  ElseIf (this.currentFrame > = 1880 & & this.currentFrame < 2010) {}

  gotoAndPlay (2010);

  }

  ElseIf (this.currentFrame > = 2010 & & this.currentFrame < 2130) {}

  gotoAndPlay (2130);

  }

  }

  function prev(event:MouseEvent) {}

  If (this.currentFrame > = 201 & & this.currentFrame < 310) {}

  gotoAndPlay (55);

  }

  ElseIf (this.currentFrame > = 310 & & this.currentFrame < 430) {}

  gotoAndPlay (201);

  }

  ElseIf (this.currentFrame > = 430 & & this.currentFrame < 530) {}

  gotoAndPlay (310);

  }

  ElseIf (this.currentFrame > = 530 & & this.currentFrame < 640) {}

  gotoAndPlay (430);

  }

  ElseIf (this.currentFrame > = 640 & & this.currentFrame < 750) {}

  gotoAndPlay (530);

  }

  ElseIf (this.currentFrame > = 750 & & this.currentFrame < 860) {}

  gotoAndPlay (640);

  }

  ElseIf (this.currentFrame > = 860 & & this.currentFrame < 970) {}

  gotoAndPlay (750);

  }

  ElseIf (this.currentFrame > = 970 & & this.currentFrame < 1080) {}

  gotoAndPlay (860);

  }

  ElseIf (this.currentFrame > = 1080 & & this.currentFrame < 1200) {}

  gotoAndPlay (970);

  }

  ElseIf (this.currentFrame > = 1200 & & this.currentFrame < 1310) {}

  gotoAndPlay (1080);

  }

  ElseIf (this.currentFrame > = 1310 & & this.currentFrame < 1420) {}

  gotoAndPlay (1200);

  }

  ElseIf (this.currentFrame > = 1420 & & this.currentFrame < 1530) {}

  gotoAndPlay (1310);

  }

  ElseIf (this.currentFrame > = 1530 & & this.currentFrame < 1690) {}

  gotoAndPlay (1420);

  }

  ElseIf (this.currentFrame > = 1690 & & this.currentFrame < 1780) {}

  gotoAndPlay (1530);

  }

  ElseIf (this.currentFrame > = 1780 & & this.currentFrame < 1880) {}

  gotoAndPlay (1690);

  }

  ElseIf (this.currentFrame > = 1880 & & this.currentFrame < 2010) {}

  gotoAndPlay (1780);

  }

  ElseIf (this.currentFrame > = 2010 & & this.currentFrame < 2130) {}

  gotoAndPlay (1880);

  }

  }

  If your sound is directly on the timeline, then change to Stream will solve your problem, but you need to change every single audio clip.

  For example if VO #1 plays frame 1 to 100, you click anywhere in this layer (where you can see the audio waveform), go to properties and flow the Sync value. If VO #2 play frame of 101 to 200, you must click somewhere in there and do the same thing. Go to the properties, press the Sync drop-down list and change the event to Stream.

  This isn't a level property 'layer '. This is a property ONLY of audio current under your cursor is in. So if you have 500 your, you need to go to each of them and the value Stream Sync event 500 times.

• Help: How can I stop the sound when I go out of the frame?

  How to stop a puppetsound when I go to another frame.

  I created a button and attached the script below to play the sound

  on mousedown

  puppetsound "the abc song".

  end

  but I want the music to stop when I'm out of the frame

  at the moment when the music is still playing when I get out of the frame.

  any help

  thanx

  You are almost correct. However, I don't think you want to reply to a #exitFrame message and stop your sound (depending on where you have the related code). Instead, use the #endSprite message (issued when the playback head leaves the span of a sprite in the score):

  on mouseDown me

  Sound (5) .play (member ("the abc song"))

  end

  on endSprite me

  Sound (5). Stop()

  end

• Simultaneous Manager timed out waiting for the output postprocessor

  Hello
  
  I am facing this error for the first time:
  
  After processing the request failed with the error message:
  Simultaneous Manager timed out waiting for the post-processor of output at the end of this request.
  
  I went through the log of the OPP and that:
  
  [05/08/09 16:00:19] [UNEXPECTED] [49106:RT4628739] java.lang.reflect.InvocationTargetException
  at sun.reflect.NativeMethodAccessorImpl.invoke0 (Native Method)
  at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39)
  at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)
  at java.lang.reflect.Method.invoke(Method.java:324)
  at oracle.apps.xdo.common.xml.XSLT10gR1.invokeProcessXSL(XSLT10gR1.java:624)
  at oracle.apps.xdo.common.xml.XSLT10gR1.transform(XSLT10gR1.java:421)
  at oracle.apps.xdo.common.xml.XSLT10gR1.transform(XSLT10gR1.java:233)
  at oracle.apps.xdo.common.xml.XSLTWrapper.transform(XSLTWrapper.java:177)
  at oracle.apps.xdo.template.fo.util.FOUtility.generateFO(FOUtility.java:1044)
  at oracle.apps.xdo.template.fo.util.FOUtility.generateFO(FOUtility.java:997)
  at oracle.apps.xdo.template.fo.util.FOUtility.generateFO(FOUtility.java:212)
  at oracle.apps.xdo.template.FOProcessor.createFO(FOProcessor.java:1657)
  at oracle.apps.xdo.template.FOProcessor.generate(FOProcessor.java:967)
  at oracle.apps.xdo.oa.schema.server.TemplateHelper.runProcessTemplate(TemplateHelper.java:5888)
  at oracle.apps.xdo.oa.schema.server.TemplateHelper.processTemplate(TemplateHelper.java:3438)
  at oracle.apps.xdo.oa.schema.server.TemplateHelper.processTemplate(TemplateHelper.java:3527)
  at oracle.apps.fnd.cp.opp.XMLPublisherProcessor.process(XMLPublisherProcessor.java:247)
  at oracle.apps.fnd.cp.opp.OPPRequestThread.run(OPPRequestThread.java:157)
  Caused by: java.lang.ThreadDeath
  at java.lang.Thread.stop(Thread.java:630)
  at oracle.apps.fnd.cp.opp.OPPRequestThreadManager.terminateThread(OPPRequestThreadManager.java:207)
  at oracle.apps.fnd.cp.opp.OPPTerminateCommand.execute(OPPTerminateCommand.java:45)
  at oracle.apps.fnd.cp.opp.OPPServiceThread.processMessage(OPPServiceThread.java:240)
  at oracle.apps.fnd.cp.opp.OPPServiceThread.waitForMessages(OPPServiceThread.java:227)
  at oracle.apps.fnd.cp.opp.OPPServiceThread.mainLoop(OPPServiceThread.java:128)
  at oracle.apps.fnd.cp.gsf.BaseServiceThread.run(BaseServiceThread.java:135)
  
  I went through the various articles and notes in the metalink:
  
  I tried increasing the values in the following profile options to their default values in 700 900
  
  Simultaneous response time: OPP
  
  Waiting period of concurrent processes: OPP
  
  but no change, can someone tell me how to decide how many seconds must be used for the profiles that is to say based on parameters, etc.
  
  Strangley than what was going on when the data is over and for this combination of setting:
  
  The total number of records in the output is approximately 5000
  
  Please guide if I missed something.
  
  Best regards
  Mahi

  You had a bad code.

  changed and he sent.

  can you check and let me know?

• How to remove the output of a SELECT on the page out of the Script

  Hello
  
  I'm running a particular piece of SQL with bind variables. The goal is to get the execution
  plan using DBMX_XPLAN. DISPLAY_CURSOR.
  
  To get the variables and bind the values of the variables in make them work, I found that I have to select
  instructions in the worksheet, and then press F5.
  
  It's working very well, but the question I have, is that this SQL data returns more 60 000 rows.
  
  I don't want to see the lines, and in addition there are limits on the number of rows can be displayed
  in SQL developer.
  
  Is there a way I can delete the results of the SQL query that appears in the output window of the Script?
  
  I tried:
  
  termout off Set
  Set autotrace traceonly
  set pagesize 0
  
  But nothing makes no difference. Surely I can stop behaving this way? Any suggestions?
  
  I use SQL Developer 3.2.09
  
  Thank you!
  
  Paul Stuart

  Hi Paul,.

  I don't believe it. Same queue the result of a query (whether inline or embedded via @.sql) does not output to the spreadsheet results pane. And internally, to explain the Plan and auto-trace, Developer SQL uses dbms_xplan.display instead of display_cursor.

  Probably your best bet is to reduce total output via Tools | Preferences | Database | Worksheet | Max lines to print in a script. That the setting does not affect the SQL sent to the database, it just limits how the SQL Developer result set that bothers to display when you run Script. Any information you get from display_cursor should be affected. Of course, the worksheet sends many other SQL to the database, that you don't see, so based on the default behavior of 'Look the last cursor' will not work. I assume that you have already taken into account for this.

  Kind regards
  Gary
  SQL development team

• Cannot use the output of javascript function in the scriptlet

  Hi I am using the listboxes in a jsp page. There are 2 drop-down lists.
  Once I click on a particular value in listbox1, the listbox2 is filled according to value in listbox1.
  
  which means I want to use the value in the list box as parameter 1 to fill the listbox2.
  
  Note: the values to listbox1 are filled with the values from the table to the oracle database.
  
  Here is the code I tried to frame.
  
  I have a listbox with the following code 1
  
  < select size = "5" cols = "30" name = "view_label" onclick = "testSelect (this.form)" > "
  
  < SCRIPT >
  function testSelect (form)
  {
  var multipleVar = form.view_label.options [form.view_label.selectedIndex] .value
  If (form.comments.value == "")
  {
  Form.comments.Value = multipleVar + "\n";
  }
  ElseIf (form.comments.value! = "")
  {
  var insertedMultipleVar = form.comments.value;
  Form.comments.Value = insertedMultipleVar + multipleVar + '\n '.
  Form.comments.Value = multipleVar
  }
  
  }
  
  < /script >
  
  
  It's listbox 2 which is based on option 1 OnClick of the listbox
  
  < select size = "5" cols = "30" name = "applications" >
  
  < %
  ResultSet rsetlovp = lovbean.getAllQueries (/ * Function testSelect output * /);
  While (rsetlovp.next ())
  {
  out.println ("< option value =" + rsetlovp.getString ("query_position") + ">" +)
  rsetlovp.getString("query_position") + ' < / option > ");
  } % >
  < / select >
  
  
  How can I switch the output of javascript function to getAllQueries() method?
  
  Please can someone help on this...?
  
  Thank you
  Ramakrishna
  
  Published by: user1064313 on July 22, 2009 05:33
  
  Published by: user1064313 on July 22, 2009 05:42

  It's really a bit difficult to answer your question without a little more information. What version of JDeveloper are you using? What is your technology environment?

  In the case of JDeveloper 11 g + +, with the Fusion technology stack, you can use a technique similar to that described here:
  http://Groundside.com/blog/GrantRonald.php?title=jdeveloper_11_business_services_cascadin&more=1&c=1&TB=1&pb=1

  JDeveloper 10.1.3 with the default Web technology stack, check here:
  http://radio.weblogs.com/0118231/stories/2004/09/23/notYetDocumentedAdfSampleApplications.html#62

  If, as looks, it is really a question about generic (no JSF) JSPs, you could actually have a little more success on a generic JSP forum - using scriptlets was not really practical copies within JDev since... Well, since JSTL became available, really. It was a number of years.

  As I said, there is really no direct way to use Javascript in a scriptlet - unless you mean something like store the output of Javascript in a hidden field and using the value in a scriptlet on the next request. But at the point where Javascript executes, a scriptlet for the current request will be already performed.

• Basic measures and the output impedance of the change with PXI-4461?

  Hello

  I am required to build an audio station with platform PXI OR test.

  It is my first experience with Renault. So I don't really know a lot...

  The PXI-4461 is a replacement of a former HP audio Analyzer. The measure is quite simple:

  1 generate fixed freq signal and measure AC RMS power

  2 measure THD (total distortion harmic) at frequency fixed

  3 measure SNR (signal to noise) at frequency fixed

  4 generate and measure DC signals

  5. change the output impedance of 50 ohms and 600 ohms.

  If I have a good feeling on which tasks 1 to 4 are feasible. I would like to ask if the task 5 (change the output impedance) problem possible?

  If this isn't a work around?

  As for tasks 1 to 4, it is possible with out doing 'a sound vibration' Toolkit?

  How helpful the Toolbox will be for the tasks listed above (humble).

  What should be my starting point learn to manage these measurement with Labview?

  Thanks in advance

  Hi Hazkel,

  Sound and Vibration toolkit will help a lot with steps 1 through 3.  This without the Toolbox would require a very high level of knowledge with LabVIEW and you will probably run again for complications.  In response to the fifth step, I tried to adapt the output impedance and am not able to do so programmtically.  However, you can still do this in hardware by adding a shunt resistor and potentially switch between if necessary impedances.  We have an article that deals with impedance matching and a circuit configuration to set the impedance if you are interested:

  Impedance and impedance matching

  http://www.NI.com/white-paper/3475/en/

  I recommend starting with examples that we have already built in LabVIEW to familiarize yourself with the concepts.  You will find them by clicking on help-> find examples-> search, then search for your application. Please let me know if you have any other questions.

  Thank you

• How to control the output voltage?

  Good time after some time can get the output voltage, but this value is alwayscontinuous. How to control the voltage output through a Boolean? In

  in order to get this tension when I want to.

  Greetings.
  Hugo Santos

  Hi Hugo,.

  If you use a LabVIEW project, you must set the time of sampling in the properties of the node (see SamplingInterval.png). But this time to refresh the data should be high enough. If you take into account this update of time trying to control your way out.

  Kind regards

• PXI-4110 deactivation and activation of the output

  I'm programmming power CC PXI-4110. I want to activate and deactivate the outputs. I use niDCPower_Disable() to disable the outputs. and the use of niDCPower_Initiate() to activate the outputs. Problem is after I have activate the outputs with niDCPower_Disable() and with niDCPower_Initiate() that I lose all my settings as the output voltage. What I so niDCPower_ConfigureVoltageLevel() and niDCPower_ConfigureCurrentLimit() call before calling niDCPower_Initiate() then outputs are put to the required voltage.

  I want to do is turn on and off just like pushing a button on a Panel.

  For example, I call niDCPower_Disable() to open the relay switch.

  It seems to me like there is a function niDCPower_Enable() which would close this switching relay and not reset all my voltage and current limit settings.

  Any help on the best way to proceed would be appreciated.

  Figured it out using:

  status = niDCPower_ConfigureOutputEnabled (vi_4110_0, channel0Name, VI_FALSE);

  to turn off and then I start with

  status = niDCPower_Initiate (vi_4110_0);

  In this way, my diet is ready to go, but my relay is open.

  When I'm ready to close the relay I follow these steps:
  status = niDCPower_ConfigureOutputEnabled (vi_4110_0, channel0Name, VI_TRUE);

  Then later I want to open the relay call again I have only this:

  status = niDCPower_ConfigureOutputEnabled (vi_4110_0, channel0Name, VI_FALSE);

  Problem solved.

• Change the output state if the connection is lost

  Hello

  I use a multifunction USB data acquisition system - 6341 XSeries to control an experience involving a heated hose.  I use MATLAB to read a number of analog sensors, and output digital to activate the relay to control certain devices of heating and a pressure relief valve.  My problem is if I lose power, someone throws a cable or my computer crashes Mid-test, I want the relay to turn off (IE, return all the digital outputs 0), for reasons of security.

  I figured out how to make the default value to the output power up to 0, but I did not find anything describing how to do the same thing if a connection with the computer is lost.  Is there a property inside the acquisition of data that I can program to do something like that?

  Thank you

  Jimmy

  The 6341 timer has a built-in digital i/o which is mentioned in the X series user manual in Chapter 6 (pdf link).

  You reset the watchdog timer of your software loop - if the timer expires the material past to a predefined State.

  I have no idea how it is configured in MATLAB, but in the C API functions used are DAQmxCreateWatchdogTimerTask to create the task and DAQmxControlWatchdogTask to reset the timer.

  Best regards

• Adjust the output value

  I am an absolute beginner to Labview, and I have so many problems that I don't know if I'll be able to finish it, even if it seems that it should be so simple.

  Here is the complete program, that I need to create, and then I'll ask my question and I hope I can get help on what is possible on this forum.

  I need to have an oscilloscope and a generator of signals communicate. I need to start a frequency and the power of the signal generator. The oscilloscope read this power as a tension (I've got this part so far). Then I need to compare this voltage to an assigned value and if they are different, adjust power accordingly on the signal generator until the voltage is equal to (with a tolerance) and the value of the rated voltage. Once this is done, I need to read the power of the signal generator and then move to the next frequency.

  The hardest part for me so far and the question for this forum is: how to compare a value of output with a value assigned and so different, adjust the output value until they become equal, remembering that I'm adjusting a power on the signal generator to get equal tension on an oscilloscope?

  I hope this question makes sense. So I'm back to this program and I don't have anyone in my group who can help me, so I'm desperate. Thanks in advance.

  davedude,

  The short answer is to use the range of comparison functions. To make a comparison with a tolerance, you can use the cooker and force function.  Always keep the Help window open context while you program - it explain the inputs and outputs and describe the basic function of the node that the cursor. One of the outputs is a Boolean value called in range? That wire to the terminal of selector of a box structure. In the case of 'out of Range', carry out the adjustment.

  The entire program should be in a while loop if all continues to repeat until done or until a button is pressed.

  A good approach for this kind of problem is to use a state machine, which can be implemented as a while loop that contains a structure of housing.  There are examples that come with LabVIEW.

  Lynn

• Is it possible to limit the output of a multi-turn encoder to match a single round?

  I use a Heidenhain encoder with an EIB Heidenhain 741. The 741 takes EnDat signals and converts them. I use a program called LabView of Heidenhain poll Positions. The encoder outputs are incremental and absolute. The outputs take into account after a revolution and I would go back to 0. The program uses a table 1 d with quad 64-bit for the absolute value and an array of 1 d of 16-bit value for the incremental values. I'm trying to convert them into degrees. I have done this except when it reaches 360 that the count is not 0. Is there a way to count position back to 0 when the number of bits is done?  Or y at - it a way to make the degrees back to 0? The degrees was taken out by taking the (Position/((2^26)/360)) which is Position/186413.51.

  This is my first large LabView project I hope this is enough information.

  Use the function Quotient & rest on the digital palette.  Divide by 360.  The output remains will always be in the range 0-359.

  Lynn

• I have a DAQ Assistant configured to read several channels at the same time. When I have a graphical indicator of wire to the output, I see all my signals mixed together. How I divided them into separate signals?

  I have a DAQ Assistant configured to read 2 channels at the same time. When I have a graphical indicator of wire to the output, I see 2 signals mixed together. How I divided them into separate signals?

  When I wire any type of indicator, it is show that a release of a single channel.

  I want 2 indicators showing 2 different signals as expected from 2 channels configured. How to do this?

  I tried to use split signal but it end by showing that 1 out of 1 signal two indicators.

  Thanks in advance.

  Yes you are right. I tried, but I don't have the result.

  I just find the path. When we launch the split signal, we should expand it (split signal icon) by top, not the bottom. It took me a while to understand this.

  Thank you

• Read the output values after each step runs in the User Interface of LabVIEW

  Hi all

  Development environment: TestStand 2010 SP1 and LabVIEW 2010 SP1

  Problem: is there a way to run the following steps programmatically and get values out of each of them?

  I have already extended a bit a complete interface IO for TestStand load any sequence, choose among the measures and execute step by step (something as an alternative to the steps run selected). What I'm trying to do is to add some actions between each step and do in the UI (I can't change the sequence!), so I start the NewExecution with some previously configured InteractiveArgsParam and option breakAtFirstStep set to true. Eventually I do just something like step over when debugging the sequence and it works well, but I didn't do well a way yet to read the output values of the place...

  So, if I wait before the end of the run I can read my results by treating the ResultObject, but it works only after the completion of the test sequence. Because I wanted to stop after each step, read the values, do some actions and continue to the next step, I've tried to register a running Trace event reminder View Manager. I see that after each step is executed, this event is fired, but when I try to read that a ResultObject returned in the event data it is not filled with values (ResultList seems to be empty?). Is this a correct behavior or maybe I'm reading the wrong way? (It's the same VI regarding the reading of the ResultObjects after the sequence ends and there it works very well for tables, containers and other types of data).

  As I mentioned I can't change Test sequences, I can not add a UImessages.

  What are my options? If the trace event returns output all the values from each steps or is it just used to check the status? Or maybe there's a completely different approach to this issue?

  Thanks in advance for your suggestions,

  Best regards.

  When you manipulate the UIMessage trace (you need this before the return of the event or you will present the race conditions), download myuimessage. Thread. Then call Thread.GetSequenceContext (0, & Iplease).

  And then on the context of the sequence, either go to PreviousStep.Result if it exists, or watch Locals.ResultList.

  Trace events occur between the steps executed step the more recently is the previous step, but it is also a trace event to the beginning before any measure have run at this time, there will be a previous step.

  Hope this helps,

  -Doug

• How can I change the configuration for the output channels analog on a PXI-6704?

  I can't seem to understand how to access the configuration of the channels to the outputs analog (channel 33 and 35) for PXI-6704.

  This piece of test equipment is out of tolerance and must be calibrated.

  I have followed the procedure of calibration http://www.ni.com/pdf/manuals/374081b.pdf, but am getting hung up on step 8, where it is said to repeat steps 4-7 when changing the _cal_ao_current_offset. I can't figure out how to open this channel because it is not listed as a physical channel for step 5.

  I'm using Labview 7.1

  Thank you

  Hello! What you need to do is to add 'Internal channels' to your list of channels, so you can choose the _cal_ao_current_offset or _cal_ao_voltage_offset.  This is done through the drop-down list channel right click and select "I/o name of screening...". ».  There will be a check box that says 'Internal channels' and will provide you with all available internal channels to enter your vi Create Channel.  I have attached some photos illustrating how to do. See you soon!