P2V on servers by omitting of VLAN different

Similar Questions

• Two servers in the same vlan, DMZ can be firewall with each other?

  I have a Windows server vm on a DMZ, and I need to add another soon.  We need to separate these two servers so that neither can see the other, but they must be on the same vlan.  I'm looking for in vShield, but do not have this installer again.  VShield will be able to separate them, or someone has a better suggestion?

  Hello

  Ah, your physical switch uses VLAN private for your guests. If you use a distributed virtual switch, you can configure one by VM PVLAN allowing entrants but no communication between the nodes.

  If you are using VMsafe you can achieve the same thing using the policy that denies the communication to the VM in VM virtual machines via subnet blocks but allows access from your firewall.

  VMsafe and vShield Zones are two distinctly different firewall technologies. vShield Zones is a firewall device VMsafe-net is located just before the vNIC on penetration or just after on the output of the vNIC. Each of the different problems, but for this use case, VMsafe can be the best way to go.

  If you do not have an Enterprise Plus license then you cannot use the virtual distributed switches so PVLANs may not work for you.

  Best regards
  Edward L. Haletky VMware communities user moderator, VMware vExpert 2009, 2010

  Now available: url = http://www.astroarch.com/wiki/index.php/VMware_Virtual_Infrastructure_Security'VMware vSphere (TM) and Virtual Infrastructure Security' [/ URL]

  Also available url = http://www.astroarch.com/wiki/index.php/VMWare_ESX_Server_in_the_Enterprise"VMWare ESX Server in the enterprise" [url]

  Blogs: url = http://www.virtualizationpractice.comvirtualization practice [/ URL] | URL = http://www.astroarch.com/blog Blue Gears [url] | URL = http://itknowledgeexchange.techtarget.com/virtualization-pro/ TechTarget [url] | URL = http://www.networkworld.com/community/haletky Global network [url]

  Podcast: url = http://www.astroarch.com/wiki/index.php/Virtualization_Security_Round_Table_Podcastvirtualization security Table round Podcast [url] | Twitter: url = http://www.twitter.com/TexiwillTexiwll [/ URL]

• Communication of VLAN different using UME.

  Hi all

  I am a beginner engineer, so I have a bit of knowledge.

  I tried to configure it by myself, but something bothers me...

  I want you guys to help me!

  In fact, I configured BPMH using the switches (CISCO & DELL) 4.

  Please provide the attachment on the photo and the configuration of file (.txt) (I draw and scanned..)

  As you can see the picture, you will know what I want to configure.

  The point I want follows content.

  (855) 935-7526 *. I want to communicate with switches together.

  -online but, Dell 7024P communicates any other switches... I think awarding IP is 30 (192,168.10.91) vlan... others have

  VLAN 10 (192.168.10.x)

  In fact, he was very big problem.

  2. only Dell 7024P does not communicate with the Internet.

  Then, I set up static routing set of switches (ip route 0.0.0.0 0.0.0.0 192.168.10.94)

  But only 7024 P does not...

  To connect to the other, what can I do in 7024 P Dell switch.

  Thank you, Daniel C.

  See the CISCO3560, executed, stp.txt

  See the CISCO3750, executed, stp.txt

  See the DELL7024P, executed, stp.txt

  See the DELL8024F, executed, stp.txt

  

  The first thing that comes out of me, is that on the P 7024 30 VLAN IP address is in the same subnet as the IP addresses of 10 VLAN on the other switches. This creates a scenario on the Cisco and 8024 switches, where you cannot assign an IP address 192.168.10.x 30 VLAN. Because VLAN 30 does not have an IP address, it cannot be routed. The resulting transmission 7024 30 VLAN Tag traffic on port gi1/0/12 article. The CISCO_3750G receives traffic labeled for 30 VLAN, but then cannot do something with it.

  There are two approaches to solve this. You can assign a different subnet to the VLAN 30. Then on each switch assign an IP address to VLAN 30. Configure the switch for VIRTUAL LAN routing on your CISCO_3750G.

  http://bit.LY/1nECOCq

  Another option would be to not use 30 VLAN. Instead use 10 VLANS on the 7024 and VLAN 10 IP address assignment the 192.168.10.91.

  Once you have the IP gene outside model, then I do it with fine adjustment covering tree instances.  Here is a white paper with some useful practices and examples of UME use.

  http://Dell.to/1MrDPx4

  See you soon

• Force 10 GbE 10/40 MXL: one port can be marked and not identified to any VLAN different at the same time?

  Dear all,

  I have to configure a 10/40 GbE switch MXL. In my scenario, each port 0/1-12 has access to 3 different networks.

  1. Management (VLAN: 10)

  2 storage (VLAN: 11)

  3. Admin (not identified)

  I can assign ports to access many VLANs. (labeled tengigabitethernet 0/1 - 12). But what happens if I have to pass the traffic which is not marked as well?

  Kind regards

  A trunk connection has a vlan native who is used for untagged traffic. Take a look at this document, he detailed step by step for a network connection.

  http://bit.LY/1EaIQW8

  See you soon

• RV180W ping hostname between VLAN & different subnets

  Hello

  I had a RV180w with 1.0.3.10 closes. According to the name of position, I'm not able to resolve host names between different VLANS which affected to different subnets, for example, allows said I have the following hosts:

  CASA:

  192.168.241.100/25 (wired - VLAN 1)

  Router: 192.168.241.1

  DNS: 192.168.241.1

  XBMC: 192.168.242.100/25 (Wi - FI - VLAN 2)

  Router: 192.168.242.1

  DNS: 192.168.242.1

  If I try to ping from two sources to one of the two destinations, the only one I get is a message 'impossible '.

  Authorized additional information routing between vlans & proxy DNS and if I try to look at the hostname under the 'nslookup' command, I could not resolve the host name, but if I do a "ping - a 192.168.241.100 ' it is said ' response from CASA (192.168.241.100) blah blah blah."

  So what I'm missing here?

  Hi Bruno, you can usually solve different subnet host name because the host does not know the subnet that treats it as a security measure.

  Disable the firewall feature on your computers and which must fix, otherwise you will probably have to change the lmhost files.

  -Tom
  Please mark replied messages useful

• New virtual machine on a VLAN different from existing virtual machines

  Hello

  I am trying to replace one of our physical servers with a virtual machine which must be on its own VIRTUAL local network.  This virtual machine will get channelled through our network to a router belonged to the client who resides with us.  I created a new group of VM ports for the new virtual machine on the standard vSwitch as the rest of our virtual machines are on with id VLAN by default of 0.  I was unable to create an id VLAN for the port group.  I have the virtual machine is set to the tag on all ports of the physical switch that the host is connected to the VLAN.  With this configuration I still can't even ping to the IP address of the physical switch for this vlan.  I feel that I'm missing something simple, but I'm pretty new to networks on vSphere.  If any information let me know.

  Hello

  Have you tried directly to type the VLAN ID in the drop-down list box. This is how to specify the VLAN ID for the virtual machines in a group of ports in the case of Virtual Switch Tagging (VST). By design, you can select a predefined VLAN ID or directly start typing the code.

  Best regards

  Iliana

• Mac OS 10.8 VM cannot reach subnet VLANS / different from the host with Fusion 5

  I have a server of Mac Mini significantly improved, high-top of the range, operating behind a firewall, Zyxel USG.  As the host, the Mac Mini runs a server OS X 10.8 virtualized with VMware Fusion 5 (mainly as an e-mail server).  To avoid opening the ports directly to the host-MacMini and LAN1 to better customize security and settings area, I want to put the virtual machine on VLAN1.

  However, no package VLAN is pass to the virtual machine.  I tried two configurations:

  Home > VLAN1 in Network preferences > VMware Fusion set to network via VLAN1 bridge > comments "Ethernet" connects effectively to the VLAN1

  Home > (LAN1) Ethernet in Network preferences > set VMware Fusion to bridge network through LAN1 > comments > add VLAN1 to guest network preferences

  In both situations, * zero packets * make out of the VM/comments on VLAN1.

  My suspicion is that VMware Fusion 5 does not support packages VLAN marked.

  Advice/suggestions for how to get the virtual machine to join VLAN1 or really, just a different subnet?  Are there drivers tagging VLAN for VMware Fusion 5?

  The FIXED - partially, at least.

  It had to do with the package being truncated by VMware.  After I have configured VLAN1 on the host, and then in the hardware parameters, chose 'Jumbo Packet Size'.  Then I jumpered the VM via connection host VLAN1.  ALTO!  This works.

  However, trying to connect to the virtual machine as a direct customer of VLAN1 is always unsuccessful. The virtual machine which truncates the packets when it sends them between the host and the guest (and vice versa).  However, if tagging VLAN is the host to level (as I have it configured), then the virtual machine can communicate successfully on the VIRTUAL LAN.

• vMotion - another subnet, VLAN different

  I'm under ESXi 4.1. I have two hosts. Currently, the management network of my hosts are on the 192.168.5.x subnet and this subnet exists in its own VIRTUAL LAN. My vMotion Setup is also included in this subnet and VLAN. What I want to do is move my vMotion for a different subnet configuration and VLAN.

  How would I go to do this? Every time I change the IP address of the vSwitch vMotion, I lose connectivity him given that I should change the gateway by default as well. When I update the default gateway, the default gateway of the management gateway is updated as well. I have to have management and vMotion on the same subnet network?

  As long as the vmkernel ports used for vmotion are on the same subenet there is no need to configure a gateway on that subnet as the traffic will never leave the subnet-

• How can I get date uniform and exit time to get-stat on servers located in areas with different regional settings?

  Hello together,

  I use a HSP on different vCenters script all over the world to sample performance data. Unfortunetaly vCenter servers concerninbg time Windows locale and date are different. For this reason that I ve had different and output date at the time of the csv. Here is an example to read a virtual computer processor performance.

  Get-Stat - feature $vm.name - Stat "cpu.usage.average" - IntervalMins 5 - (Get-Date).adddays(-1)-.addminutes(-5)-MaxSamples Start to finish (Get-Date) 288. Select-Object timestamp, value, unit | Export-Csv

  vCenter Server located in the United States with the American Time (12-hour AM/PM) and the settings of Date (day/month/year):

  'Timestamp', 'Value', 'unit '.

  "2010-06-27 12:00 PM","2.75","%.

  "

  "

  vCenter Server located in Europe with countries European regionalen (24 hours) and Date settings (day.month.year):

  Timestamp, value, unit

  "21.06.2010 20:00:00", "3.06", %

  "

  "

  For the import of these data to our central database, the formats must be uniform.

  Someone at - it an idea to get the uniform format?

  Thanks in advance

  Concerning

  Oliver

  Why don't you use the solution in Use-Culture - Culture culture - Script {scriptblock} ?

  You do all the writing to your database in 1 selected (for example en-US culture).

  This way all your date and and digital formats have the same layout.

  ____________

  Blog: LucD notes

  Twitter: lucd22

• List of Ports TCP UDP VMware Converter 4.0.1 P2V DMZ servers?

  Can someone list all TCP/UDP ports required to run VMware converter through a firewall? This is so that we can P2V Windows DMZ servers specific to both ESX in our DMZ servers.

  How about you use this instead?

  VMware vCenter converter required ports

  http://KB.VMware.com/kb/1010056/

  Kind regards

  EvilOne

  VMware vExpert 2009

  NOTE: If your question or problem has been resolved, please mark this thread as answered and awarded points accordingly.

• WAP321 - captive portal in 2 VLAN different

  Hello

  I have a Wap321 installed in my network.  IP: 192.168.0.36 - VLAN 1

  If I'm in the local network, I don't have any problem to use the wireless.

  I just added a guest VLAN for people who need to connect Internet, without access to the network. So I install a second SSID and label with vlan 50. I can access the Internet.  But if I want to active the captive portal, I can't access it because the address is in the VLAN 1 (or 192.168.0.36).

  How can I configure my Wap321 having the captive portal in the VLAN 50, and not in the VLAN 1?

  Thank you

  Alex

  Hi Alexander,.

  For interVlan on ISA5510 setting, yes the same security settings is the first step to enable this function runs. This article will help you configure InterVlan routing.

  https://supportforums.Cisco.com/thread/2035882

• WLC SETUP VLAN DIFFERENT & SSID

  Hello world

  I have a scenario in which WLC 2504 is connected to access 4507R + E.and Core switch switches are connected to the switch of base as well. In these access toggle AIR-CAP702I-A-K9 access points.

  My question is this:

  I want to use vlan 104 for office with SSID OFFICE-EMPLOYEES

  I want to use vlan 103 for guest with SSID Office-guests

  Here's what I have set the main switch

  (config) #interface xx

  (config) #description xxx

  trunk mode (config) #switchport

  (config) #switchport trunk allowed vlan 103 104

  Here's what I have configured on the access switches

  (config) #interface xx

  access mode (config) #swithcport

  (config) #swithcport access vlan 104

  If I setup port trunk on access switches and access points allowing 103 & 104 both vlan are not joining controller.

  Right now, IP management is of vlan 104 and all access points and clients receive an ip of the vlan 104.

  What I will do in this scenario. I want to use separate traffic office employee and comments.

  It would be great if someone can help me.

  Hello

  I guess the AP management vlan is 104!

  Please check the latter:

  Config of switch Core for WLC:

  interface GigabitEthernet XX
  Description * Cisco WLC *.
  switchport trunk encapsulation dot1q
  switchport trunk allowed vlan 103 104
  switchport mode trunk
  no downtime
  !

  Access to AP light switch:

  interface GigabitEthernet1/0/22
  Description * AP *.
  switchport access vlan 104
  switchport mode access
  no downtime

  Switch to access switch uplink port and vice versa, must be configured as a trunk port.

  Concerning

  Remember messages useful rates

• Allow VPN users access a VLAN different

  I have an ASA 5505.  I have configured remote access VPN so that users can connect to the VPN and access my main VIRTUAL local network (inside).  I want to set so that when a user s in VPN, they are permitted access only to the CCV vlan (Vlan 2) as seen in my configuration.  Please note that there is also a VPN LAN LAN 2, which has been set up as well.

  What Miss me?

  !
  interface Ethernet0/0
  switchport access vlan 4
  !
  interface Ethernet0/1
  !
  interface Ethernet0/2
  !
  interface Ethernet0/3
  !
  interface Ethernet0/4
  !
  interface Ethernet0/5
  !
  interface Ethernet0/6
  switchport access vlan 2
  !
  interface Ethernet0/7
  switchport access vlan 2
  !
  interface Vlan1
  nameif inside
  security-level 100
  IP 10.240.0.1 255.255.0.0
  !
  interface Vlan2
  prior to interface Vlan1
  nameif HVAC
  security-level 100
  IP address 172.16.128.1 255.255.255.0
  !
  interface Vlan4
  nameif outside
  security-level 0
  IP address 12.x.x.x 255.255.255.0
  !
  passive FTP mode
  IP 10.240.0.0 allow Access - list extended CDEO 255.255.0.0 10.0.0.0 255.0.0.0
  IP 10.240.0.0 allow Access - list extended sheep 255.255.0.0 10.0.0.0 255.0.0.0
  IP 10.240.0.0 allow Access - list extended sheep 255.255.0.0 172.16.129.0 255.255
  . 255.0
  IP 10.102.229.0 allow Access - list extended sheep 255.255.255.0 172.16.129.0 255
  . 255.255.0
  IP 172.16.129.0 allow Access - list extended sheep 255.255.255.0 10.102.229.0 255
  . 255.255.0
  access-list sheep extended ip 172.16.128.0 allow 255.255.255.0 172.16.129.0 255
  . 255.255.0
  IP 172.16.129.0 allow Access - list extended sheep 255.255.255.0 172.16.128.0 255
  . 255.255.0
  list of inbound icmp permitted access extended throughout entire echo response
  list of extended inbound icmp permitted access any source-quench any
  list of extended all inbound icmp permitted access all inaccessible
  access list entering permit icmp any once extended beyond
  coming out to the one permitted all ip extended access list
  standard vpn access list allows 10.240.0.0 255.255.0.0
  standard vpn access list allows 10.102.229.0 255.255.255.0
  list of access allowed standard vpn 172.16.128.0 255.255.255.0
  pager lines 24
  asdm of logging of information
  Within 1500 MTU
  Outside 1500 MTU
  MTU 1500 HVAC
  IP local pool 172.16.129.1 - 172.16.129.5 mask 255.255.255.0 shhfvpnpool
  ICMP unreachable rate-limit 1 burst-size 1
  don't allow no asdm history
  ARP timeout 14400
  Global 1 interface (outside)
  NAT (inside) 0 access-list sheep
  NAT (inside) 1 0.0.0.0 0.0.0.0
  Access-group out on the interface inside
  Access-group interface incoming outside
  Route outside 0.0.0.0 0.0.0.0 12.x.x.x 1
  dynamic-access-policy-registration DfltAccessPolicy
  the ssh LOCAL console AAA authentication
  No snmp server location
  No snmp Server contact
  Server enable SNMP traps snmp authentication linkup, linkdown cold start
  Crypto ipsec transform-set esp - esp-sha-hmac hand
  Crypto ipsec transform-set esp - esp-md5-hmac RIGHT
  life crypto ipsec security association seconds 28800
  Crypto ipsec kilobytes of life - safety 4608000 association
  Crypto-map dynamic dynmap 10 transform-set RIGHT
  life together - the association of security crypto dynamic-map dynmap 10 28800 seconds
  Crypto-map dynamic dynmap 10 kilobytes of life together - the association of safety 4608000
  Crypto-map dynamic dynmap 10 the value reverse-road
  CDEOVPN 35 crypto card matches the address CDEO
  CDEOVPN 35 crypto map set peer 64.x.x.x
  card crypto CDEOVPN 35 the transform-set hand value
  map CDEOVPN 100-isakmp ipsec crypto dynamic dynmap
  CDEOVPN interface card crypto outside
  crypto isakmp identity address
  crypto ISAKMP allow outside
  crypto ISAKMP policy 20
  preshared authentication
  the Encryption
  sha hash
  Group 1
  life 86400
  crypto ISAKMP policy 30
  preshared authentication
  the Encryption
  md5 hash
  Group 2
  life 86400

  Console timeout 0
  management-access inside

  a basic threat threat detection
  Statistics-list of access threat detection
  no statistical threat detection tcp-interception
  attributes of Group Policy DfltGrpPolicy
  VPN-idle-timeout no
  internal group shhf strategy
  attributes of shhf group policy
  VPN-idle-timeout 30
  VPN-session-timeout 1440
  VPN-filter no
  Protocol-tunnel-VPN IPSec
  Split-tunnel-policy tunnelspecified
  Split-tunnel-network-list value vpn

  tunnel-group 64.x.x.x type ipsec-l2l
  64.x.x.x group tunnel ipsec-attributes
  pre-shared key *.
  tunnel-group shhf type remote access
  tunnel-group shhf General attributes
  address shhfvpnpool pool
  strategy-group-by default shhf
  shhf group tunnel ipsec-attributes
  pre-shared key *.
  tunnel-group vpnclient type remote access
  !
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  maximum message length automatic of customer
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  inspect the rsh
  inspect the rtsp
  inspect esmtp
  inspect sqlnet
  inspect the skinny
  inspect sunrpc
  inspect xdmcp
  inspect the sip
  inspect the netbios
  inspect the tftp
  Review the ip options
  !
  global service-policy global_policy
  context of prompt hostname
  no remote anonymous reporting call
  Cryptochecksum:1cbd55e987f9b41cd2ebcb320fa2e3b2
  : end

  This route to be applied on the switch, if your port eth0/7 on SAA is connected to a switch of later3.

  "Route ip 172.16.129.0 255.255.255.0 172.16.128.1.

  So, don't worry on this route, if you can not apply on the SAA.

  So are you saying that a PC is directly connected to eth0/7 on the SAA.

  What is the IP address, mask and gateway address on the PC connected on eth0/7?

  The trace package seems good.

• App 5.1 server does not not on different VLANS

  Helloooo

  I just installed a new server and I use the server application. Everything seemed to work fine until I moved my iMac to a VLAN different. Profiles and update settings do not push to the iMac and sit at a stadium in waiting. Also to register the new iMacs on the server I get to the login server window and it crashes it and does not authenticate. Screen opens by saying that I can open a second window and registration. When I try to register, I get an unknown error and that it fails. It seems timeless. I tried to change a lot of settings prescribed by other users, but nothing helped. Someone at - it advice on what could be the problem.

  See you soon

  Sean

  Hello

  I took the easy on this way and bring a USB ethernet to my mac so that I have two physical interfaces. An in each VLAN.

  There are other ways to do this, and this is a good article:

  https://blog.Pivotal.IO/Labs/Labs/using-deploystudio-across-Subnets-a-Path-Not-t Aken

  Kind regards

  Erik

• Wake on LAN (WOL) through different VLAN on SG-300-10

  Hello

  I try to get WOL working through different VLAN on a Switch SG-300-10 in layer 3 Mode.  To achieve this, I set up a UDP relay (GUI menu Configuration IP) for UDP Port 7 to 255.255.255.255 (this should inundate all interfaces with the package), however, does not work WOL in different VLANS.  When I am connected directly to the VLAN corresponding, WOL works fine in the same subnet.  Am I missing something here?

  All comments appreciated!

  Thank you very much!

  Hi Romeo,.

  A few minutes to try it on my SG300 - 10 p mode layer 3.

  My NAS unit is capable WOL and I thought I would use it in my test environment...

  Ran a basic test to check my sender of packet Magic from my PC "awakened" my NAS unit.

  As you would expect, on the same subnet, the magic packet WOL caused my NAS unit to power, no problem.

  But this isn't really the test, just a test database to check that my sender of the packet magic WOL and NAS was working well.

  The screenshot below shows WOL software I used on my PC.  Why use this software, no reason except that it was available for free. Also, I'm sure other WOL software out there for different platforms that work just as well or with more features.

  

  First of all, I see according to your question, you used relays UDP destination port 7, well it is the default setting on the UDP relay on my switch.

  I wonder why you used or stayed with destination UDP port 7, because the Magic packet mailers may use different destination UDP ports?

  I had to use wireshark to see the real destination UDP port that uses my sender of the magic packet WOL.

  

  Notice of capturing wireshark above, that my magic packet software uses the UDP port destination 9, NOT the default value that you can see on the switch. Ignore what wireshark labels this port.

  OK, I then created a VLAN that I named "VLAN2' with a = 2 VID on my SG300 - 10 p (SRW2008P-K9-NA)

  I added a 192.168.2.1/24 IP interface to VLAN2, which is a different network from the default VLAN.

  I then added three ports this VLAN newly created as a member untagged VLAN2.

  The default VLAN (VID = 1) an IP network 192.168.10.0/24.

  My NAS (WOL capable) unit has an IP address of 192.168.10.61.

  I plugged my PCt to the vlan 2 and statically assigned 192.168.2.2/24.  It is the PC that has the magic package software.

  I added a route static to my router WAN, just so that I could access the router my PC attached to the VLAN2 WAN.

  I tried the magic packet WOL software and will not turn on my NAS.  He expected that the magic packet broadcast would never jump over a limit of LAN in one VLAN different...

  Now, I tried to install a UDP relay so that the Magic Packet WOL "would be" the VLAN2 network interface VLAN1.

  So I configure and add to my SG300 UDP relay entry - 10 p.   See the screen capture below.

  I have to admit, I'm used to using UDP relay normally take a netbios broadcast and unicast to a server Ms.

  But check the screenshot below, I put the switch to send the UDP relay to the broadcast address of VLAN1 network... The magic packet Wakeup sent from my PC into 2 VLANS must have passed over the limit VLAN that my NAS unit woke.

  

  In order to check the destination port UDP to your WOL software using wireshark, and then create an appropriate UDP relay.

  Experiment and play with that, once you get your device WOL properly powereing successfully.

  Best regards, Dave

  If I answered your question, please rate the relevance of this response