Allow VPN users access a VLAN different
I have an ASA 5505. I have configured remote access VPN so that users can connect to the VPN and access my main VIRTUAL local network (inside). I want to set so that when a user s in VPN, they are permitted access only to the CCV vlan (Vlan 2) as seen in my configuration. Please note that there is also a VPN LAN LAN 2, which has been set up as well.
What Miss me?
!
interface Ethernet0/0
switchport access vlan 4
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
switchport access vlan 2
!
interface Ethernet0/7
switchport access vlan 2
!
interface Vlan1
nameif inside
security-level 100
IP 10.240.0.1 255.255.0.0
!
interface Vlan2
prior to interface Vlan1
nameif HVAC
security-level 100
IP address 172.16.128.1 255.255.255.0
!
interface Vlan4
nameif outside
security-level 0
IP address 12.x.x.x 255.255.255.0
!
passive FTP mode
IP 10.240.0.0 allow Access - list extended CDEO 255.255.0.0 10.0.0.0 255.0.0.0
IP 10.240.0.0 allow Access - list extended sheep 255.255.0.0 10.0.0.0 255.0.0.0
IP 10.240.0.0 allow Access - list extended sheep 255.255.0.0 172.16.129.0 255.255
. 255.0
IP 10.102.229.0 allow Access - list extended sheep 255.255.255.0 172.16.129.0 255
. 255.255.0
IP 172.16.129.0 allow Access - list extended sheep 255.255.255.0 10.102.229.0 255
. 255.255.0
access-list sheep extended ip 172.16.128.0 allow 255.255.255.0 172.16.129.0 255
. 255.255.0
IP 172.16.129.0 allow Access - list extended sheep 255.255.255.0 172.16.128.0 255
. 255.255.0
list of inbound icmp permitted access extended throughout entire echo response
list of extended inbound icmp permitted access any source-quench any
list of extended all inbound icmp permitted access all inaccessible
access list entering permit icmp any once extended beyond
coming out to the one permitted all ip extended access list
standard vpn access list allows 10.240.0.0 255.255.0.0
standard vpn access list allows 10.102.229.0 255.255.255.0
list of access allowed standard vpn 172.16.128.0 255.255.255.0
pager lines 24
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
MTU 1500 HVAC
IP local pool 172.16.129.1 - 172.16.129.5 mask 255.255.255.0 shhfvpnpool
ICMP unreachable rate-limit 1 burst-size 1
don't allow no asdm history
ARP timeout 14400
Global 1 interface (outside)
NAT (inside) 0 access-list sheep
NAT (inside) 1 0.0.0.0 0.0.0.0
Access-group out on the interface inside
Access-group interface incoming outside
Route outside 0.0.0.0 0.0.0.0 12.x.x.x 1
dynamic-access-policy-registration DfltAccessPolicy
the ssh LOCAL console AAA authentication
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp - esp-sha-hmac hand
Crypto ipsec transform-set esp - esp-md5-hmac RIGHT
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
Crypto-map dynamic dynmap 10 transform-set RIGHT
life together - the association of security crypto dynamic-map dynmap 10 28800 seconds
Crypto-map dynamic dynmap 10 kilobytes of life together - the association of safety 4608000
Crypto-map dynamic dynmap 10 the value reverse-road
CDEOVPN 35 crypto card matches the address CDEO
CDEOVPN 35 crypto map set peer 64.x.x.x
card crypto CDEOVPN 35 the transform-set hand value
map CDEOVPN 100-isakmp ipsec crypto dynamic dynmap
CDEOVPN interface card crypto outside
crypto isakmp identity address
crypto ISAKMP allow outside
crypto ISAKMP policy 20
preshared authentication
the Encryption
sha hash
Group 1
life 86400
crypto ISAKMP policy 30
preshared authentication
the Encryption
md5 hash
Group 2
life 86400
Console timeout 0
management-access inside
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
attributes of Group Policy DfltGrpPolicy
VPN-idle-timeout no
internal group shhf strategy
attributes of shhf group policy
VPN-idle-timeout 30
VPN-session-timeout 1440
VPN-filter no
Protocol-tunnel-VPN IPSec
Split-tunnel-policy tunnelspecified
Split-tunnel-network-list value vpn
tunnel-group 64.x.x.x type ipsec-l2l
64.x.x.x group tunnel ipsec-attributes
pre-shared key *.
tunnel-group shhf type remote access
tunnel-group shhf General attributes
address shhfvpnpool pool
strategy-group-by default shhf
shhf group tunnel ipsec-attributes
pre-shared key *.
tunnel-group vpnclient type remote access
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
!
global service-policy global_policy
context of prompt hostname
no remote anonymous reporting call
Cryptochecksum:1cbd55e987f9b41cd2ebcb320fa2e3b2
: end
This route to be applied on the switch, if your port eth0/7 on SAA is connected to a switch of later3.
"Route ip 172.16.129.0 255.255.255.0 172.16.128.1.
So, don't worry on this route, if you can not apply on the SAA.
So are you saying that a PC is directly connected to eth0/7 on the SAA.
What is the IP address, mask and gateway address on the PC connected on eth0/7?
The trace package seems good.
Tags: Cisco Security
Similar Questions
-
I have a professional Windows 7 operating system and have a program that was installed when the user is logged on as a local user. Is it possible to give the same user rights to run this program without having to reinstall the program when the user is connected to the domain?
Thanks for any help you can provide.
Microsoft Answers is for consumers to related issues and it would be preferable for you to post in the following TechNet forum.
http://social.technet.Microsoft.com/forums/en-us/w7itprogeneral/threads
Sincerely,
Marilyn
-
Allow a user to implement a different network
Is there a way to set permissions on a folder or a virtual machine on which you can specify what networks a specific user or a group can put in place. Say you have 3 available networks, but you want to leave only go to 2 of the three, how would you do that?
Thank you
Henry
Welcome to the communities...
You can try the below
Inventory of Goto-> Networking section, create a folder, move the Group of ports on this issue and try to set the permission on the folder
-
Remote access VPN user permission
Hi support them.
It is a way for a remote access VPN to allow some users access to "Host A, B, C" and other users to access hosts D, E, F? Basically, we want to have some users have access at home to a few servers and other users have access only to some other servers. Is this possible without a GANYMEDE or some other device? Thank you guys!
Hi John,.
Yes, you can configure split tunneling to allow a specific group of users access to specific hosts.
How this is achieved, it is that you create a connection profile different for different users, associate a policy group and the title of each group policy, you have a split tunnelling access-list defined with entries of different hosts.You must create 2 profiles of connection here and match them with 2-group policy allowing access to 2 differernt resources (they can be multiple as well)
Here is a reference document: -.
Kind regards
Dinesh MoudgilPS Please rate helpful messages.
-
no client AnyConnect vpn internet access
AnyConnect vpn client no internet no access.
Here is the configuration. Help, please.
Thank you
Jessie
ASA Version 8.2 (1)
!
hostname ciscoasa5505
!
interface Vlan1
nameif inside
security-level 100
IP 172.16.0.1 255.255.0.0
!
interface Vlan2
nameif outside
security-level 0
IP address 69.x.x.54 255.255.255.248
!
interface Vlan5
Shutdown
prior to interface Vlan1
nameif dmz
security-level 50
DHCP IP address
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
passive FTP mode
DNS lookup field inside
DNS domain-lookup outside
DNS server-group DefaultDNS
Server name 172.16.0.2
Server name 69.x.x.6
object-group Protocol TCPUDP
object-protocol udp
object-tcp protocol
object-group service TS-777-tcp - udp
port-object eq 777
object-group service Graphon tcp - udp
port-object eq 491
object-group service TS-778-tcp - udp
port-object eq 778
object-group service moodle tcp - udp
port-object eq 5801
object-group service moodle-5801 tcp - udp
port-object eq 5801
object-group service 587 smtp tcp - udp
EQ port 587 object
outside_access_in list extended access permit tcp any host 69.x.x.50 eq imap4
outside_access_in list extended access permit tcp any host 69.x.x.52 eq ftp
outside_access_in list extended access allowed object-group TCPUDP any object-group of 69.x.x.50 host smtp-587
outside_access_in list extended access permit tcp any host 69.x.x.52 eq telnet
outside_access_in list extended access permit tcp any host 69.x.x.52 eq ssh
outside_access_in list extended access allowed object-group TCPUDP any host object-group moodle-5801 69.x.x.52
outside_access_in list extended access permit tcp any host 69.x.x.52 eq smtp
outside_access_in list extended access permit tcp any host 69.x.x.52 eq https
outside_access_in list extended access permit tcp any host 69.x.x.52 eq www
outside_access_in list extended access permit tcp any host 69.x.x.50 eq ftp
outside_access_in list extended access permit tcp any host 69.x.x.50 eq smtp
outside_access_in list extended access permit tcp any host 69.x.x.50 eq pop3
outside_access_in list extended access allowed object-group TCPUDP any host 69.x.x.50 EQ field
outside_access_in list extended access permit tcp any host 69.x.x.50 eq https
outside_access_in list extended access permit tcp any host 69.x.x.50 eq www
outside_access_in list extended access allowed object-group TCPUDP any host 69.x.x.51 EQ field
outside_access_in list extended access allowed object-group TCPUDP any host TS-778 69.x.x.51 object-group
outside_access_in list extended access allowed object-group TCPUDP any host Graphon 69.x.x.51 object-group
outside_access_in list extended access permit tcp any host 69.x.x.51 eq https
outside_access_in list extended access permit tcp any host 69.x.x.51 eq www
outside_access_in list extended access allowed object-group TCPUDP any host TS-777 69.x.x.50 object-group
outside_access_in list extended access permit tcp any host 69.x.x.54 eq https
access extensive list ip 172.16.0.0 outside_cryptomap_1 allow 255.255.0.0 192.168.50.0 255.255.255.0
access extensive list ip 172.16.0.0 inside_nat0_outbound allow 255.255.0.0 192.168.0.0 255.255.255.0
inside_nat0_outbound list of allowed ip extended access all 172.16.0.32 255.255.255.224
access extensive list ip 172.16.0.0 inside_nat0_outbound allow 255.255.0.0 192.168.50.0 255.255.255.0
access extensive list ip 172.16.0.0 inside_nat0_outbound allow 255.255.0.0 192.168.1.0 255.255.255.0
inside_access_in of access allowed any ip an extended list
Standard Split-Tunnel access list permit 172.16.0.0 255.255.0.0
access-list SHEEP extended ip 172.16.0.0 allow 255.255.0.0 192.168.0.0 255.255.255.0
access-list SHEEP extended ip 172.16.0.0 allow 255.255.0.0 192.168.50.0 255.255.255.0
access-list SHEEP extended ip 172.16.0.0 allow 255.255.0.0 192.168.1.0 255.255.255.0
access-list SHEEP extended ip 172.16.0.0 allow 255.255.0.0 172.16.0.0 255.255.0.0
access extensive list ip 172.16.0.0 outside_cryptomap allow 255.255.0.0 192.168.0.0 255.255.255.0
access extensive list ip 172.16.0.0 outside_cryptomap_2 allow 255.255.0.0 192.168.1.0 255.255.255.0
pager lines 24
Enable logging
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
MTU 1500 dmz
IP local pool VPN_Users 172.16.100.10 - 172.16.100.20 mask 255.255.255.0
IP local pool anypool 172.16.0.9 - 172.16.0.19 mask 255.255.0.0
ICMP unreachable rate-limit 1 burst-size 1
don't allow no asdm history
ARP timeout 14400
Global 1 interface (outside)
NAT (inside) 0 access-list SHEEP
NAT (inside) 1 0.0.0.0 0.0.0.0
public static 69.x.x.50 (Interior, exterior) 172.16.0.2 netmask 255.255.255.255
public static 69.x.x.51 (Interior, exterior) 172.16.1.2 netmask 255.255.255.255
public static 69.x.x.52 (Interior, exterior) 172.16.1.3 netmask 255.255.255.255
inside_access_in access to the interface inside group
Access-group outside_access_in in interface outside
Route outside 0.0.0.0 0.0.0.0 69.x.x.49 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-registration DfltAccessPolicy
Enable http server
http 172.16.0.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
card crypto outside_map 1 match address outside_cryptomap
card crypto outside_map 1 set pfs
card crypto outside_map 1 set 208.x.x.162 counterpart
card crypto outside_map 1 set of transformation-ESP-3DES-SHA
card crypto outside_map 2 match address outside_cryptomap_1
card crypto outside_map 2 set pfs
card crypto outside_map 2 peers set 209.x.x.178
card crypto outside_map 2 the value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
card crypto outside_map 3 match address outside_cryptomap_2
card crypto outside_map 3 set pfs
card crypto outside_map 3 peers set 208.x.x.165
card crypto outside_map 3 game of transformation-ESP-3DES-SHA
outside_map interface card crypto outside
crypto ISAKMP allow outside
crypto ISAKMP policy 5
preshared authentication
3des encryption
sha hash
Group 2
life 86400
crypto ISAKMP policy 30
preshared authentication
3des encryption
sha hash
Group 1
life 86400
Telnet timeout 5
SSH timeout 5
Console timeout 0
dhcpd outside auto_config
!
dhcpd address 172.16.0.20 - 172.16.0.40 inside
dhcpd dns 172.16.0.2 69.x.x.6 interface inside
dhcpd allow inside
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
allow outside
SVC disk0:/anyconnect-win-2.5.2014-k9.pkg 1 image
enable SVC
tunnel-group-list activate
attributes of Group Policy DfltGrpPolicy
Server DNS 172.16.0.2 value
Protocol-tunnel-VPN IPSec l2tp ipsec svc webvpn
Group Policy inside sales
Group sales-policy attributes
value of server DNS 172.16.1.2 172.16.0.2
VPN-tunnel-Protocol svc
Split-tunnel-policy tunnelspecified
Split-tunnel-network-list value split Tunnel
WebVPN
SVC mtu 1406
internal group anyconnect strategy
attributes of the strategy group anyconnect
VPN-tunnel-Protocol svc webvpn
WebVPN
list of URLS no
SVC request to enable default webvpn
username of graciela CdnZ0hm9o72q6Ddj encrypted password
graciela username attributes
VPN-group-policy DfltGrpPolicy
tunnel-group 208.x.x.165 type ipsec-l2l
208.x.x.165 group of tunnel ipsec-attributes
pre-shared-key *.
tunnel-group AnyConnect type remote access
tunnel-group AnyConnect General attributes
address anypool pool
strategy-group-by default anyconnect
tunnel-group AnyConnect webvpn-attributes
Group-alias anyconnect enable
allow group-url https://69.x.x.54/anyconnect
tunnel-group 208.x.x.162 type ipsec-l2l
208.x.x.162 tunnel ipsec-attributes group
pre-shared-key *.
tunnel-group 209.x.x.178 type ipsec-l2l
209.x.x.178 group of tunnel ipsec-attributes
pre-shared-key *.
!
Global class-card class
match default-inspection-traffic
!
!
World-Policy policy-map
Global category
inspect the icmp
!
service-policy-international policy global
context of prompt hostname
: end
Hello
You could start by adding the following configurations
permit same-security-traffic intra-interface
This will allow traffic to the VPN users access the interface ' outside ' of the SAA and to leave to the Internet using the same interface ' outside '. Without the above command, it is not possible.
Also, you need to add a NAT configuration for VPN Client users can use the Internet connection of the ASA
To do this, you can add this command
NAT (outside) 1 172.16.0.0 255.255.0.0
This will allow the PAT for the Pool of VPN dynamics.
Hope this helps
Don't forget to mark the reply as the answer if it answered your question.
Ask more if necessary
-Jouni
-
remote users access site ipsec tunnel
How to configure the ACL and the road to allow remote users access to site ipsec as local users?
Current scenario is
1. distance users (192.168.2.0/24) ipsec <->Cisco 870 (192.168.0.0/24)
(2 cisco 870(192.168.0.0/24) ipsec tunnel <->cisco 1811 (10.0.0.0/24)
Now remote users can access the 192.168.0.0 network, no problem, but how they can access 10.0.0.0 network?
I guess I can do like this:
1. in cisco 870, site to site ip 192.168.0.0 tunnel allow 0.0.0.255 10.0.0.0 0.0.0.255
(add) permit ip 192.168.2.0 0.0.0.255 10.0.0.0 0.0.0.255
2. in the site-to-site vpn cisco 1811
(add) permit ip 10.0.0.0 0.0.0.255 192.168.2.0 0.0.0.255
3. in settings vpn split cisco870 add the 10.0.0.0/24 network
Is this fair?
Thank you.
You must configure the interesting traffic that an ACL contains the source is remote destination as local LAN and LAN.
->-> -
Create different group with VPN remote access
Hello world
The last time, I ve put in place a VPN for remote access to my network with ASA 5510
I ve access to all my internal LAn helped with my VPN
But I want to set up a vpn group in the CLI for a different group of the user who accesses the different server or a different network on my local network.
Example: computer group - access to 10.70.5.X network
Group consultant network - access to 10.70.10.X
I need to know how I can do this, and if you can give me some example script to complete this
Here is my configuration:
ASA Version 8.0 (2)
!
ASA-Vidrul host name
vidrul domain name - ao.com
activate 8Ry2YjIyt7RRXU24 encrypted password
names of
DNS-guard
!
interface Ethernet0/0
nameif outside
security-level 0
address IP X.X.X.X 255.255.255.X
!
interface Ethernet0/1
nameif inside
security-level 100
address IP X.X.X.X 255.255.255.X
!
interface Ethernet0/2
Shutdown
No nameif
no level of security
no ip address
!
interface Ethernet0/3
Shutdown
No nameif
no level of security
no ip address
!
interface Management0/0
Description Port_Device_Management
nameif management
security-level 99
address IP X.X.X.X 255.255.255.X
management only
!
2KFQnbNIdI.2KYOU encrypted passwd
passive FTP mode
DNS server-group DefaultDNS
vidrul domain name - ao.com
access-list 100 scope ip allow a whole
access-list extended 100 permit icmp any any echo
access-list extended 100 permit icmp any any echo response
vpn-vidrul_splitTunnelAcl permit 10.70.1.0 access list standard 255.255.255.0
vpn-vidrul_splitTunnelAcl permit 10.70.99.0 access list standard 255.255.255.0
inside_nat0_outbound list of allowed ip extended access all 10.70.255.0 255.255.255.0
pager lines 24
Outside 1500 MTU
Within 1500 MTU
MTU 1500 management
IP local pool clientvpngroup 10.70.255.100 - 10.70.255.200 mask 255.255.255.0
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm - 602.bin
don't allow no asdm history
ARP timeout 14400
Global 1 interface (outside)
NAT (inside) 0-list of access inside_nat0_outbound
NAT (inside) 1 10.70.0.0 255.255.0.0
Access-group 100 in the interface inside
Access-group 100 interface insideTimeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout, uauth 0:05:00 absolute
dynamic-access-policy-registration DfltAccessPolicy
Protocol RADIUS AAA-server 10.70.99.10
AAA authentication enable LOCAL console
the ssh LOCAL console AAA authentication
LOCAL AAA authorization command
Enable http server
http 192.168.1.2 255.255.255.255 management
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
Dynamic crypto map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs
SYSTEM_DEFAULT_CRYPTO_MAP game 65535 dynamic-map crypto transform-set ESP-DES-SHA ESP-DES-MD5
outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
outside_map interface card crypto outside
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
the Encryption
md5 hash
Group 2
life 86400
Crypto isakmp nat-traversal 30
Telnet 0.0.0.0 0.0.0.0 inside
Telnet timeout 5
SSH 0.0.0.0 0.0.0.0 outdoors
SSH timeout 5
Console timeout 0
outside access management
dhcpd manage 192.168.1.2 - 192.168.1.5
dhcpd enable management
!
a basic threat threat detection
Statistics-list of access threat detection
!
class-map inspection_default
match default-inspection-traffic
block-url-class of the class-map
class-map imblock
match any
class-map P2P
game port tcp eq www
!
!
type of policy-card inspect dns migrated_dns_map_1
parameters
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the migrated_dns_map_1 dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the netbios
inspect the rsh
inspect the rtsp
inspect the skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect the tftp
inspect the sip
inspect xdmcp
Policy-map IM_P2P
class imblock
class P2P
!
global service-policy global_policy
vpn-vidrul group policy internal
vpn-vidrul group policy attributes
Protocol-tunnel-VPN IPSec
Split-tunnel-policy tunnelspecified
Split-tunnel-network-list value vpn-vidrul_splitTunnelAcl
value by default-field vidrul - ao.com
test 274Y4GRAbNElaCoV of encrypted password privilege 0 username
username admin privilege 15 encrypted password bTpUzgLxalekyhxQ
attributes of user admin name
Strategy-Group-VPN-vpn-vidrul
username, password suporte zjQEaX/fm0NjEp4k encrypted privilege 15
type tunnel-group vidrul-vpn remote access
vpn-vidrul general-attributes tunnel-group
address clientvpngroup pool
Group Policy - by default-vpn-vidrul
IPSec-vpn-vidrul tunnel group attributes
pre-shared-key *.
context of prompt hostname
Cryptochecksum:d84e64c87cc5b263c84567e22400591c
: endWhat you need to configure is to imitate the configuration on the tunnel-group and group strategy and to configure access to specific network you need.
Currently, you have configured the following:
vpn-vidrul group policy internal
vpn-vidrul group policy attributes
Protocol-tunnel-VPN IPSec
Split-tunnel-policy tunnelspecified
Split-tunnel-network-list value vpn-vidrul_splitTunnelAcl
value by default-field vidrul - ao.comtype tunnel-group vidrul-vpn remote access
vpn-vidrul general-attributes tunnel-group
address clientvpngroup pool
Group Policy - by default-vpn-vidrul
IPSec-vpn-vidrul tunnel group attributes
pre-shared-key *.What you need is to create new group policy and the new tunnel-group and configure the tunnel split ACL to allow access to specific access required.
The user must then connect with the new group name and the new pre-shared key (password).
Hope that helps.
-
Matter of principle: allow internal VPN users to external networks
Hi people.
We receive requests from our internal users, asking the ability/permission to VPN in outside networks businesses of related objectives. They would use our business machines sitting on our corporate network and perhaps required VPN software installation/configuration (for example, Nortel, Microsoft PPTP, IPSec Cisco, etc.) They go out through our ASA Firewall and then connect to the remote network.
Currently, we block out IPSec and PPTP to avoid this problem, and the reason why we give is that you are connecting two networks and potentially open our internal network up to who knows what.
In the past we have remote offices install stand-alone DSL lines and ACL acceding to the external VPN, but it becomes expensive and bulky. The same for wireless EVDO cards.
With the current state of the economy, the price of gas or movement, etc., becomes more difficult to refuse these requests and the higher Up inside are getting hit by operational units.
How guys do you deal with that? What reasons did you give for allowing / preventing external access VPN? The problem is better solved with the policy or technical (or both?) You poke holes and make exceptions for specific external VPNS, and if so, what are the requirements don't surround you?
Thanks for any input!
-Neil
In the case of IPSec, I'm not sure you fill the two networks.
You allow traffic be sent through tunnel through your good firewall, and the limits imposed on passenger transport are generally determined by the thrust of policy from the other end of the VPN of parties and any software firewall on your host computer.
I think it boils down to the protection of the appropriate host on your end, and some common sense as to which the parties, you are allowed to connect too (written policy).
The Cisco VPN Client provides a built-in firewall and the ability to restrict your host to access the local LAN while the tunnel is UP.
-
AnyConnect VPN users cannot access remote subnets?
I googled this until blue in the face without result. I don't understand why Cisco this so difficult? When clients connect to the anyconnect vpn, they can access the local subnet, but cannot access the resources in remote offices. What should I do to allow my anyconnect vpn clients access to my remote sites?
Cisco 5510 8.4
Hello
What are remote sites using as Internet gateway? Their default route here leads to the ASA or have their own Internet gateway? If they use this ASA for their Internet connection while they should already have a default route that leads traffic to the VPN to the pool, even if they had no specific route for the VPN itself pool. If they use their own local Internet gateway and the default route is not directed to this ASA then you would naturally have a route on the remote site (and anything in between) indicating the remote site where to join the pool of 10.10.224.0/24 VPN network.
In addition to routing, you must have configured for each remote site and the VPN pool NAT0
Just a simple example of NAT0 configuration for 4 networks behind the ASA and simple VPN field might look like this
object-group network to REMOTE SITES
object-network 10.10.10.0 255.255.255.0
object-network 10.10.20.0 255.255.255.0
object-network 10.10.30.0 255.255.255.0
object-network 10.10.40.0 255.255.255.0
network of the VPN-POOL object
10.10.224.0 subnet 255.255.255.0
NAT static destination DISTANCE-SITES SITES source (indoor, outdoor) REMOTE static VPN-VPN-POOL
The above of course assumes that the remote site are located behind the interface 'inside' (although some networks, MPLS) and naturally also the remote site networks are made for the sake of examples.
Since you are using Full Tunnel VPN should be no problem to the user VPN transfer traffic to this ASA in question.
My first things to check would be configuring NAT0 on the ASA and routing between remote sites and this ASA (regarding to reach the VPN pool, not the ASA network IP address)
Are you sure that the configuration above is related to this? Its my understanding that AnyConnect uses only IKEv2 and the foregoing is strictly defined for IKEv1?
-Jouni
-
Allowing external IP access via VPN Client
We are looking for our remote VPN users to access an external IP address. Basically once users authenticate when they try to access 202.1.56.19, they should be out nat through the external interface of the firewall. Below is out of the package violated on "vpn ecrypt" tracer and as an extract from the config. On the client, I see that the road to 202.1.56.19 was added, but it does not work.
Please advise more information be required ing. Thank you.
access list INSIDE-OUT scope ip 10.15.160.0 allow 255.255.255.0 any
access OUTSIDE list / allowed extended Interior ip 10.15.160.0 255.255.255.0 any
Access-group OUTSIDE / inside interface OUTSIDE-IDCNONATIDC list of allowed ip extended access all 10.15.160.0 255.255.255.0
NAT (INSIDE) 0-list of access NONATIDC
NAT (INSIDE) 1 10.15.160.0 255.255.255.0
Global (OUTSIDE-IDC) 1 128.15.155.2internal CorpVPN group strategy
attributes of Group Policy CorpVPN
value of server DNS 10.15.155.17
VPN-idle-timeout no
VPN-session-timeout no
Protocol-tunnel-VPN IPSec
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list SplitTunnel
something.com value by default-fieldattributes global-tunnel-group CorpVPN
address pool CorpVPNpool
Group Policy - by default-CorpVPN
IPSec-attributes tunnel-group CorpVPN
pre-shared keyStandard access list SplitTunnel allow 192.168.168.0 255.255.255.0
SplitTunnel list standard access allowed host 202.1.56.19Packet-trace input outside-iDC tcp 10.15.160.18 22 202.1.56.19 22
Phase: 1
Type: ACCESS-LIST
Subtype:
Result: ALLOW
Config:
Implicit rule
Additional information:
MAC access listPhase: 2
Type: FLOW-SEARCH
Subtype:
Result: ALLOW
Config:
Additional information:
Not found no corresponding stream, creating a new streamPhase: 3
Type:-ROUTE SEARCH
Subtype: entry
Result: ALLOW
Config:
Additional information:
in 0.0.0.0 0.0.0.0 OUTSIDE-IDCPhase: 4
Type: ACCESS-LIST
Subtype: Journal
Result: ALLOW
Config:
Access-group OUTSIDE / inside interface OUTSIDE-IDC
access OUTSIDE list / allowed extended Interior ip 10.15.160.0 255.255.255.0 any
Additional information:Phase: 5
Type: IP-OPTIONS
Subtype:
Result: ALLOW
Config:
Additional information:Phase: 6
Type: CP-PUNT
Subtype:
Result: ALLOW
Config:
Additional information:Phase: 7
Type: VPN
Subtype: ipsec-tunnel-flow
Result: ALLOW
Config:
Additional information:Phase: 8
Type: VPN
Subtype: encrypt
Result: DECLINE
Config:
Additional information:Result:
input interface: OUTSIDE-IDC
entry status: to the top
entry-line-status: to the top
output interface: OUTSIDE-IDC
the status of the output: to the top
output-line-status: to the top
Action: drop
Drop-reason: flow (acl-drop) is denied by the configured ruleEssentially, the traffic needs to make a u-turn at ASA outside interface if I understand your configuration.
You need the following to make it work.
-permit same-security-traffic intra-interface
-Host202 of the 10.15.160.0 ip access list permit 255.255.255.0 host 202.1.56.19
-nat (OUTSIDE-IDC) 1 access-list Host202
-
Auth of remote VPN through LDAP allow all users!
Hello
I have 5505 firewall and security license. I have configure remote VPN on firewall through CLI with the commands below. Remote VPN works well, but the problem is, it allows all remote VPN users. I need to restrict remote VPN access bit user, I need to configure via CLI, I don't want to go through ASDM, can someone help me with CLI?
ASDM I can able to perfom below things I'm not able to perform through CLI
Configuration-> access to the network (Client)-> dynamic access policies
Through ASDM I'm able to set the VPN users are allow to remote VPN access, how to set up same thing through CLI
Here's my CLI:
LDAP attribute-map CISCOMAP
name of the KFG IETF Radius-class card
map-value VPN CN = VPN, DC = domain, DC = com noaccess_pri
map-value VPN CN = VPN, DC = domain, DC = com noaccess_bk
map-value VPN CN = VPN, DC = domain, DC = com splitgroup_pri
map-value VPN CN = VPN, DC = domain, DC = com splitgroup_bk
AAA-server ldapgroup protocol ldap
ldapgroup AAA-server (inside) host 10.1.10.5
LDAP-base-dn dc = domain, dc = com
LDAP-scope subtree
LDAP-naming-attribute sAMAccountName
LDAP-login-password Inf0rmati0n1
LDAP-connection-dn cn = VPN, dc = domain, dc = com
microsoft server type
LDAP-attribute-map CISCOMAP
internal noaccess_pri group policy
attributes of the strategy of group noaccess_pri
VPN - concurrent connections 0
output
internal noaccess_bk group policy
attributes of the strategy of group noaccess_bk
VPN - concurrent connections 0
output
internal splitpolicy_pri group policy
Protocol-tunnel-VPN IPSEC l2tp ipsec
tunnel-group splitgroup_pri General-attributes
ldapgroup group-LOCAL authentication server
internal splitpolicy_bk group policy
Protocol-tunnel-VPN IPSEC l2tp ipsec
tunnel-group splitgroup_bk General-attributes
ldapgroup group-LOCAL authentication server
Thank you
Abhishek
Hello
You cannot configure the DAP via CLI Protocol because the configuration is saved in a file dap.xml and is stored in flash of the SAA.
You can configure the DAP protocol using the following link:
http://www.ciscosystems.com/en/us/products/ps6120/products_white_paper09186a00809fcf38.shtml#T4
Also note that the link mentions the following:
Note:
The dap.xml file that contains the attributes of selection policies DAP, is stored in flash of the SAA. Although you can export the file dap.xml out, the edit box (if you know about the xml syntax), and re - import again, be very careful, because you might ASDM stop treatment of DAP files if you have misconfigured something. There is no CLI to handle this part of the configuration.
I hope this helps.
Kind regards
Anisha
P.S.: Please mark this message as answered if you feel that your query is resolved. Note the useful messages.
-
How to allow VPN PPTP by ASA access
Hi guys,.
I allow VPN clients to internal PPTP server located behind a firewall of ASA and running on a Windows 2 K 8 Server machine.
I found that the Setup is different on the version of the ASA. I'm under ASA Version 8.2 (5).
There are many rules in place and keep the. I found a lot of guides is bad because they push the drive to remove the existing rules rather than add new.
Can you please let me know how? (If possible via ADSM) and if I have to wait the questions when I decide to upgrade my ASA?
Thank you
Dario
You must configure static NAT translation because I believe that the PPTP traffic is incoming from the Internet.
You must allow PPTP traffic on the external interface: TCP/1723
You must enable PPTP inspection: inspect pptp
-
How can I assign the static fixed IP for remote access VPN users
Hi team,
I have a requirement to assign a fixed static IP users VPN remote access in ASA, please help how I can achice this
Thanks in advance
Mikaelusername user1 attributes
VPN-framed-ip-address 10.200.115.78 255.255.0.0
-
Client VPN cannot access the different internal subnet
Hi all
I use pix 7.0 and 4,8 vpn client
When I connect with the vpn client, I see the subnet behind the pix (10.61.1.0)
However, there is a router on that subnet that connects to two other sites (10.61.2.0 and 10.72.2.0)
I can ping from the pix to these subnets command line.
When I connect using the vpn client I only see the subnet behind the pix and not the other two subnets?
I have a command-line 10.0.0.0 255.0.0.0 10.61.1.250 (the ip address of the router) on the pix, but this doesn't seem to help?
The response from the ping is request timed out one or the other subnets.
Any suggestions on what route, I need to add or is there an ACL to be added?
Current and ACL routes is:
0.0.0.0 0.0.0. The ISP router address
10.0.0.0 255.0.0.0 10.61.1.250
Outside_access_in list extended access permit icmp any one
access extensive list ip 10.61.1.0 inside_nat0 allow 255.255.255.0 10.61.1.224 255.255.255.240
NAT (inside) 0-list of access inside_nat0
NAT (inside) 10 0.0.0.0 0.0.0.0
Access-group Outside_access_in in interface outside
All responses appreciated.
first of all and above all, the pool of the vpn client should not overlap with the asa inside the subnet, or any connected subnet.
<-->Asa <-->(10.61.1.250) Internet router <-->10.61.2.0 and 10.72.2.0
allow inside_nat0 to access extended list ip 10.61.1.0 255.255.255.0
allow inside_nat0 to access extended list ip 10.61.2.0 255.255.255.0
allow inside_nat0 to access extended list ip 10.72.2.0 255.255.255.0
Allow Outside_cryptomap_dyn_20 to access extended list ip 10.61.1.0 255.255.255.0
Allow Outside_cryptomap_dyn_20 to access extended list ip 10.61.2.0 255.255.255.0
Allow Outside_cryptomap_dyn_20 to access extended list ip 10.72.2.0 255.255.255.0
In addition, a static route must be configured on the 10.61.1.250 router:
IP route
-->-->--> -
Refuse the remote user VPN to access PC using VPN from Site users to partner Site
Hi Experts,
Installation program:
We have configured IPSEC Site - Site VPN between Cisco ASA 5510 and Sonicwall.
Tunnel is in place and working well, we are able to access the remote workstation to partner and Vis Versa.
Requirment: We want to deny remote VPN users, who are our partners access to the workstation.
Example:
Remote IP address range: 192.168.200.x/2r4
Local IP address range: 192.168.10.x/24
Deny traffic from 192.168.200.x/24 to 192.168.10.x/24
Thanks in advance
Kiran Kumar CH
Hi Kiran,
You want to deny certain IP addresses of the Remote LAN (of the L2L tunnel), to connect to your workstation?
Thus, if the remote network 192.168.200.0/24, want to deny some of these machines to connect to 192.168.10.x?
If this is the case, you can create ACL VPN (VPN filters) on the SAA to restrictive traffic through the tunnel from the IPs.
Please clarify if I have misunderstood.
Federico.
Maybe you are looking for
-
App Store will not be updated iTunes on Mac 10.11.6 12.5.1
Downloads of the app store iTunes 12.5.1 updated, but when he starts the installation it stops, update disappears from the list was updated and the update button does not work. I am running on a 15 "mid 2010 MacBook Pro 10.11.6. In collaboration wi
-
I need help to retrieve my hard drive using the recovery of Neosmart disk (it takes days)
To get a better perspective, I'll tell you the history of what has gone wrong. What happened is that the computer has a virus and it changed some coding on the computer. When this happened to that my computer wouldn't let me enter my account and the
-
Repair disk Vista not working does not and cannot correct the disk error
Hello. I have a disc error and my vista repair disc does not work and I do not know why. I tried "repair disk" in the start menu F12 and it will not work. Does anyone know an alternative solution for fixing windows disk repair? Anyone know why they w
-
Windows Media Burning question Code also Native Code C0AA0402__ C00D119F
When I enter the tab burn and enter my cd Virgin bar which displays the left space or space automatically has a red bar that runs through and read FILLED below him. BUT it will still burn an audio cd and not a data disc. Any ideas?
-
Is it possible to dynamically change the drawstyle after a field has been created? I can not find a method to do this... Field.setStyle ()? Thank you Jon