RV180W ping hostname between VLAN & different subnets

Similar Questions

• Mac OS 10.8 VM cannot reach subnet VLANS / different from the host with Fusion 5

  I have a server of Mac Mini significantly improved, high-top of the range, operating behind a firewall, Zyxel USG.  As the host, the Mac Mini runs a server OS X 10.8 virtualized with VMware Fusion 5 (mainly as an e-mail server).  To avoid opening the ports directly to the host-MacMini and LAN1 to better customize security and settings area, I want to put the virtual machine on VLAN1.

  However, no package VLAN is pass to the virtual machine.  I tried two configurations:

  Home > VLAN1 in Network preferences > VMware Fusion set to network via VLAN1 bridge > comments "Ethernet" connects effectively to the VLAN1

  Home > (LAN1) Ethernet in Network preferences > set VMware Fusion to bridge network through LAN1 > comments > add VLAN1 to guest network preferences

  In both situations, * zero packets * make out of the VM/comments on VLAN1.

  My suspicion is that VMware Fusion 5 does not support packages VLAN marked.

  Advice/suggestions for how to get the virtual machine to join VLAN1 or really, just a different subnet?  Are there drivers tagging VLAN for VMware Fusion 5?

  The FIXED - partially, at least.

  It had to do with the package being truncated by VMware.  After I have configured VLAN1 on the host, and then in the hardware parameters, chose 'Jumbo Packet Size'.  Then I jumpered the VM via connection host VLAN1.  ALTO!  This works.

  However, trying to connect to the virtual machine as a direct customer of VLAN1 is always unsuccessful. The virtual machine which truncates the packets when it sends them between the host and the guest (and vice versa).  However, if tagging VLAN is the host to level (as I have it configured), then the virtual machine can communicate successfully on the VIRTUAL LAN.

• vMotion between hosts on different subnets

  Before you start, I'm a network engineer, not a server guru, please bare with me

  Is it possible to vMotion a virtual machine to a host on an IP network to another host, on a different IP network?

  Example:

  Data Center 1 - 10.1.1.1/24 with VM in the 10.1.2.0/24 ESX Server

  Same city, different site, binding fiber 10 GB between facilities 2ms latency

  Data Center 2 - 10.2.1.1/24 in the 10.2.2.0/24 with VM ESX Server

  Scenario:

  vMotion a computer virtual network 10.1.2.0/24 to the 10.2.2.0/24 network where virtual machine, on arrival on the ESX 2 data center server, now uses a IP address of 10.2.2.0/24.

  Any guidance towards a white paper or a guide would be greatly appreciated.

  Thank you all for your time.

  -Chris

  Network engineer

  Press Ganey Associates

  vMotion is possible between hosts on different subnets, but unless your discussions presented to the virtual machines are on the same subnet, you will eventually drop the virtual machine on a VLAN different and IP addressing will fail.

  There are ways around this, you could script the change of IP address / present several IP addresses of the virtual machine / or reservations DHCP to use, but you will need to ensure DNS etc. records are updated.

  If you have some kind of load balancer, you could in theory balance workloads on 2 IPs hosted on the same VM, to solve the network ip address issues, although in the end, you'll want a VLAN tended to port VM coverage groups.

  Good luck

• vMotion - another subnet, VLAN different

  I'm under ESXi 4.1. I have two hosts. Currently, the management network of my hosts are on the 192.168.5.x subnet and this subnet exists in its own VIRTUAL LAN. My vMotion Setup is also included in this subnet and VLAN. What I want to do is move my vMotion for a different subnet configuration and VLAN.

  How would I go to do this? Every time I change the IP address of the vSwitch vMotion, I lose connectivity him given that I should change the gateway by default as well. When I update the default gateway, the default gateway of the management gateway is updated as well. I have to have management and vMotion on the same subnet network?

  As long as the vmkernel ports used for vmotion are on the same subenet there is no need to configure a gateway on that subnet as the traffic will never leave the subnet-

• ASA 5505: VPN access to different subnets

  Hi All-

  I'm trying to understand how to configure our ASA so that remote users can have VPN access to two different subnets (Office LAN and LAN phone).  Currently I have 3 VLAN configuration - VLAN 1 (inside), VLAN 2 (outside), VLAN 13 (phone LAN).  Essentially, remote users must be able to access their PC (192.168.1.0/24) and also have access to the office phone system (192.168.254.0/24).  Is it still possible?  Here are the configurations on our ASA,

  Thanks in advance:

  ASA Version 8.2 (5)

  !

  names of

  name 10.0.1.0 Net-10

  name 20.0.1.0 Net-20

  name phone 192.168.254.0

  name 192.168.254.250 PBX

  !

  interface Ethernet0/0

  switchport access vlan 2

  !

  interface Ethernet0/1

  !

  interface Ethernet0/2

  !

  interface Ethernet0/3

  !

  interface Ethernet0/4

  !

  interface Ethernet0/5

  switchport access vlan 3

  !

  interface Ethernet0/6

  !

  interface Ethernet0/7

  switchport access vlan 13

  !

  interface Vlan1

  nameif inside

  security-level 100

  192.168.1.98 IP address 255.255.255.0

  !

  interface Vlan2

  nameif outside

  security-level 0

  address IP X.X.139.79 255.255.255.224

  !

  interface Vlan3

  No nameif

  security-level 50

  192.168.5.1 IP address 255.255.255.0

  !

  interface Vlan13

  nameif phones

  security-level 100

  192.168.254.200 IP address 255.255.255.0

  !

  passive FTP mode

  object-group service RDP - tcp

  EQ port 3389 object

  object-group service DM_INLINE_SERVICE_1

  the purpose of the ip service

  EQ-ssh tcp service object

  vpn_nat_inside of access list extensive ip Net-10 255.255.255.224 allow 192.168.1.0 255.255.255.0

  access-list extended vpn_nat_inside allowed ip Net-10 255.255.255.224 phones 255.255.255.0

  inside_nat0_outbound list extended access permits all ip Net-10 255.255.255.224

  inside_access_in of access allowed any ip an extended list

  Split_Tunnel_List list standard access allowed Net-10 255.255.255.224

  phones_nat0_outbound list extended access permits all ip Net-10 255.255.255.224

  outside_access_in list extended access allowed object-group DM_INLINE_SERVICE_1 Mac host everything

  pager lines 24

  Enable logging

  timestamp of the record

  record monitor errors

  record of the mistakes of history

  asdm of logging of information

  Within 1500 MTU

  Outside 1500 MTU

  MTU 1500 phones

  mask IP local pool SSLClientPool-10 10.0.1.1 - 10.0.1.20 255.255.255.128

  no failover

  ICMP unreachable rate-limit 1 burst-size 1

  don't allow no asdm history

  ARP timeout 14400

  Global interface (10 Interior)

  Global 1 interface (outside)

  global interface (phones) 20

  NAT (inside) 0-list of access inside_nat0_outbound

  NAT (inside) 1 0.0.0.0 0.0.0.0

  NAT (10 vpn_nat_inside list of outdoor outdoor access)

  NAT (phones) 0-list of access phones_nat0_outbound

  NAT (phones) 1 0.0.0.0 0.0.0.0

  inside_access_in access to the interface inside group

  Access-group outside_access_in in interface outside

  Route outside 0.0.0.0 0.0.0.0 X.X.139.65 1

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  timeout tcp-proxy-reassembly 0:01:00

  Floating conn timeout 0:00:00

  dynamic-access-policy-registration DfltAccessPolicy

  AAA authentication enable LOCAL console

  the ssh LOCAL console AAA authentication

  LOCAL AAA authorization command

  Enable http server

  http 192.168.1.0 255.255.255.0 inside

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown cold start

  Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

  Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac

  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

  life crypto ipsec security association seconds 28800

  Crypto ipsec kilobytes of life - safety 4608000 association

  Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

  outside_map interface card crypto outside

  Crypto ca trustpoint ASDM_TrustPoint0

  registration auto

  name of the object CN = not - asa .null

  pasvpnkey key pair

  Configure CRL

  crypto ISAKMP allow outside

  crypto ISAKMP policy 10

  preshared authentication

  3des encryption

  sha hash

  Group 2

  lifetime 28800

  VPN-sessiondb max-session-limit 10

  Telnet timeout 5

  SSH 192.168.1.100 255.255.255.255 inside

  SSH 192.168.1.0 255.255.255.0 inside

  SSH Mac 255.255.255.255 outside

  SSH timeout 60

  Console timeout 0

  dhcpd auto_config inside

  !

  dhcpd address 192.168.1.222 - 192.168.1.223 inside

  dhcpd dns 64.238.96.12 66.180.96.12 interface inside

  !

  a basic threat threat detection

  host of statistical threat detection

  Statistics-list of access threat detection

  a statistical threat detection tcp-interception rate-interval 30 burst-400-rate average rate 200

  SSL-trust outside ASDM_TrustPoint0 point

  WebVPN

  allow outside

  AnyConnect essentials

  SVC disk0:/anyconnect-win-2.5.2014-k9.pkg 1 image

  SVC disk0:/anyconnect-macosx-i386-2.5.2014-k9.pkg 2 image

  enable SVC

  tunnel-group-list activate

  internal SSLClientPolicy group strategy

  attributes of Group Policy SSLClientPolicy

  WINS server no

  value of 64.238.96.12 DNS server 66.180.96.12

  VPN-access-hour no

  VPN - connections 3

  VPN-idle-timeout no

  VPN-session-timeout no

  IPv6-vpn-filter no

  VPN-tunnel-Protocol svc

  group-lock value NO-SSL-VPN

  by default no

  VLAN no

  NAC settings no

  WebVPN

  SVC mtu 1200

  SVC keepalive 60

  client of dpd-interval SVC no

  dpd-interval SVC bridge no

  SVC compression no

  attributes of Group Policy DfltGrpPolicy

  value of 64.238.96.12 DNS server 66.180.96.12

  Protocol-tunnel-VPN IPSec svc webvpn

  attributes global-tunnel-group DefaultRAGroup

  address-pool SSLClientPool-10

  IPSec-attributes tunnel-group DefaultRAGroup

  pre-shared key *.

  NO-SSL-VPN Tunnel-group type remote access

  General-attributes of the NO-SSL-VPN Tunnel-group

  address-pool SSLClientPool-10

  Group Policy - by default-SSLClientPolicy

  NO-SSL-VPN Tunnel - webvpn-attributes group

  enable PAS_VPN group-alias

  allow group-url https://X.X.139.79/PAS_VPN

  !

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  maximum message length automatic of customer

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the preset_dns_map dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  inspect the rsh

  inspect the rtsp

  inspect esmtp

  inspect sqlnet

  inspect the skinny

  inspect sunrpc

  inspect xdmcp

  inspect the sip

  inspect the netbios

  inspect the tftp

  Review the ip options

  !

  global service-policy global_policy

  privilege level 3 mode exec cmd command perfmon

  privilege level 3 mode exec cmd ping command

  mode privileged exec command cmd level 3

  logging of the privilege level 3 mode exec cmd commands

  privilege level 3 exec command failover mode cmd

  privilege level 3 mode exec command packet cmd - draw

  privilege show import at the level 5 exec mode command

  privilege level 5 see fashion exec running-config command

  order of privilege show level 3 exec mode reload

  privilege level 3 exec mode control fashion show

  privilege see the level 3 exec firewall command mode

  privilege see the level 3 exec mode command ASP.

  processor mode privileged exec command to see the level 3

  privilege command shell see the level 3 exec mode

  privilege show level 3 exec command clock mode

  privilege exec mode level 3 dns-hosts command show

  privilege see the level 3 exec command access-list mode

  logging of orders privilege see the level 3 exec mode

  privilege, level 3 see the exec command mode vlan

  privilege show level 3 exec command ip mode

  privilege, level 3 see fashion exec command ipv6

  privilege, level 3 see the exec command failover mode

  privilege, level 3 see fashion exec command asdm

  exec mode privilege see the level 3 command arp

  command routing privilege see the level 3 exec mode

  privilege, level 3 see fashion exec command ospf

  privilege, level 3 see the exec command in aaa-server mode

  AAA mode privileged exec command to see the level 3

  privilege, level 3 see fashion exec command eigrp

  privilege see the level 3 exec mode command crypto

  privilege, level 3 see fashion exec command vpn-sessiondb

  privilege level 3 exec mode command ssh show

  privilege, level 3 see fashion exec command dhcpd

  privilege, level 3 see the vpnclient command exec mode

  privilege, level 3 see fashion exec command vpn

  privilege level see the 3 blocks from exec mode command

  privilege, level 3 see fashion exec command wccp

  privilege see the level 3 exec command mode dynamic filters

  privilege, level 3 see the exec command in webvpn mode

  privilege control module see the level 3 exec mode

  privilege, level 3 see fashion exec command uauth

  privilege see the level 3 exec command compression mode

  level 3 for the show privilege mode configure the command interface

  level 3 for the show privilege mode set clock command

  level 3 for the show privilege mode configure the access-list command

  level 3 for the show privilege mode set up the registration of the order

  level 3 for the show privilege mode configure ip command

  level 3 for the show privilege mode configure command failover

  level 5 mode see the privilege set up command asdm

  level 3 for the show privilege mode configure arp command

  level 3 for the show privilege mode configure the command routing

  level 3 for the show privilege mode configure aaa-order server

  level mode 3 privilege see the command configure aaa

  level 3 for the show privilege mode configure command crypto

  level 3 for the show privilege mode configure ssh command

  level 3 for the show privilege mode configure command dhcpd

  level 5 mode see the privilege set privilege to command

  privilege level clear 3 mode exec command dns host

  logging of the privilege clear level 3 exec mode commands

  clear level 3 arp command mode privileged exec

  AAA-server of privilege clear level 3 exec mode command

  privilege clear level 3 exec mode command crypto

  privilege clear level 3 exec command mode dynamic filters

  level 3 for the privilege cmd mode configure command failover

  clear level 3 privilege mode set the logging of command

  privilege mode clear level 3 Configure arp command

  clear level 3 privilege mode configure command crypto

  clear level 3 privilege mode configure aaa-order server

  context of prompt hostname

  no remote anonymous reporting call

  Hello

  Loss of connectivity to the LAN is not really supposed all remove this command UNLESS your network is using another device as their gateway to the Internet. In this case configuration dynamic PAT or political dynamics PAT (as you) would make sense because the LAN hosts would see your VPN connection from the same directly connected network users and would be know to traffic before the ASA rather than their default gateway.

  So is this just for VPN usage and NOT the gateway on the LAN?

  If it is just the VPN device I'd adding this

  global interface (phones) 10

  He would do the same translation for 'phones' as he does on 'inside' (of course with different PAT IP)

  -Jouni

• How VLANs ' IP subnet ing works with based port of VLAN (series N2000 and N3000)

  Hi all

  I have a small pile of x N3024 2 acting as my heart L3 with a lag of 2 x 10 g down to a stack of x N2048 5 acting as L2 switch for my PC workstations.

  Workstations are that all on the port assigned VLAN 10 (switchport access vlan 10). I have a bunch of developers who want to access without restrictions more or less to assign random IP addresses for their VM (Virtualbox and VMware) Workstation.  As you can imagine, I would like some control over this situation.  the powerconnect guide I described features of subnet IP VLAN but does not seem to enter in how it works and interacts with the port actually function vlan assignments.

  What I currently have is the VLAN 10 assigned to a segment that support the subnet 172.100.x.x which dates back to our base of L3 for routing to other segments. What I want to do is to configure the VLAN based on IP and then load the dev is to config their VM with another IP range, say 10.10.x.x.

  Theory here is, I set the L3 core with say 20 VLAN and an IP to register in L3 path between subnets and then configure the battery switch L2 workstation with IP - based VLAN to recognize 10.10.x.x and separate on VLAN 20.

  However, I think the simplified here question is if I have a nail up to 10 ports VLAN, will the than basic work IP subnet VLANS as I want only it? Or, I need to create a subnet IP VIRTUAL local area network for the two IP ranges? I have to remove the assignenment VLAN per port and are based entirely on the treatment of subnet IP VLAN?

  If there is a better RTFM on this topic you can tell me I would appreciate it

  Thank you!

  I ended up calling specialists... great Dell technical support here.

  In fact, the IP based VLAN works very close to what I want to achieve. Missing from the user guide is that the port needs to be in the mode. Ports using switch port mode and bound to a VLAN just didn't work... probably because the vlan IP based did not differ from the port binding. Dell support has suggested to use the trunk mode, but my answer is finished using the general mode; any traffic not referenced, PVID located my usual LAN vlan ID and acceptance of port traffic of new vlan based on IP. In this way, I'm able to have a physical host DHCP on the corporate LAN and a virtual machine on that host to bind to a different subnet which is then isolated in the new NAV based on IP.

• WLAN clients in different subnet

  Hi all

  I was using the setting of the current with WLC2106 and 2 rounds.  So far, the management and the ap-Manager interface where on the same subnet (192.168.0.x).  I was using a static IP address for wireless clients, also on the 192.168.0.x.  If far so good and everything was up and running.  Now, I wanted wireless clients to get an IP address from the DHCP server in the 192.168.0.x subnet.  Leased IP addresses will be on another network - 192.168.7.x.  I tried to change the ap - manager for and IP address on the reseau.7.x and set DHCP server on both interfaces.  However, I can't customers aren't being associated with it, and when I try and give a static IP address on the reseau.7.x, I can't ping anything customers.  The routing is not the problem as I have confirmed that it works well.

  Should I change the management interface (as the WIFI network is associated with this interface, and I can't choose the ap - manager)?  Or do I have to use a dynamic interface?

  Thank you

  Tiziana

  Hello Tiziana,

  In order to remove the clients on a different subnet / VLAN other than on your AP-Manager interfaces and management, you will need to deploy a new dynamic interface on the WLC.  Also make sure that the trunk on the vlan again at the WLC.  Here is an excellent guide that explains how to accomplish this.

  VLANs on the example of Configuration of wireless LAN controllers
  http://www.Cisco.com/en/us/Tech/tk722/tk809/technologies_configuration_example09186a00805e7a24.shtml

  I hope this helps.

  See you soon,.

  Drew

• IPSec tunnels between duplicate LAN subnets

  Hi all

  Please help to connect three sites with our Central site has all the resources for users, including internet access.

  The three sites will be the ASA 5505 like their WAN device.

  We need to know is - it possible, allowing to configure an IPsec Tunnel between the three ASA with duplicate LAN subnets.

  Central site two networks 192.168.1.x 24, 192.168.100.x 24

  Distance a 24 192.168.1.x subnet

  Two remote a subnet 192.168.100.x 24

  If it is possible we also do hair distance one ping, above two remote to the Central Site to access internet, what sites need are on the Central Site, including e-mail, network, other resource also records.

  We have no other way to make this network, as all security is on our Central Site, website filtering, Application filtering, filtering of network traffic all.

  We understand that we can change two remote sites to a different subnet from the Central Site, but we have so many host devices, it will take weeks or months, so to change the MS AD domain for all users, servers too.

  We really need your expertise to do this in a laboratory and then in production.

  Thank you

  Hello Stephen,

  You can check the following links for the subnets overlap talk to each other:-

  1 LAN-to-LAN IPsec VPN with overlapping networks

  http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a0080b37d0b.shtml

  2 IPsec between two IOS routers with overlapping of private networks

  http://www.Cisco.com/en/us/products/ps5855/products_configuration_example09186a0080a0ece4.shtml

  Important point is local network must connect to the remote network via the translated addresses.

  for example, you won't be ablt to use real IP of the communication.

  For haripinning or turning U:

  http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a00805734ae.shtml

  Hope that helps.

  Kind regards

  Dinesh Moudgil

• Different subnets HA DRS VM

  Hello

  I've seen many threads on this subjects.but, I'm new to the world of Vm and I have never done this kind of configuration in our environment. So, I need help fromyou guys!...

  I implemented a cluster using the DRS and HA for 2 different subnets environment... I configured using one and I have no problem... But, now I'll need to build esx 6... 3 for a subnet. .other 3 for another subnet.

  I read, whateever being used ip address, we just need a physical connection between them, I mean, Vlan and for work HA we have put in place an advanced on hearbeat setting change the default network... is this correct?

  Anyway, my question would be if the guests located on ESX on first subnet can work in an another ESX on different subnet?

  I mean, if we had some comments moved by DRS or HA to another host with different subnet, it'll work?

  Please, I always research it upward on the communities vmware, but if someone could help me? It would be nice...

  Thanks in advance.

  I read, whateever being used ip address, we just need a physical connection between them, I mean, Vlan and for work HA we have put in place an advanced on hearbeat setting change the default network... is this correct?

  I think you are talking about http://kb.vmware.com/kb/1019200

  Anyway, my question would be if the guests located on ESX on first subnet can work in an another ESX on different subnet?

  I mean, if we had some comments moved by DRS or HA to another host with different subnet, it'll work?

  The management and the network of the virtual machine are different. You can do the cluster to function with the hosts in different subnets, however, for networks in the virtual machine, you will need to provide the same VLAN / networks on physical switch ports, if the virtual machine will not be able to access the network on the other host.

  André

• Two guests with a different subnet on the same bridge vmnet0

  Hi all, I have a server in a data center.  The data center has awarded me two different

  Beaches of IP addresses with two separate subnets.  The first beach with the subnet to 255.255.255.248

  compatible with my 3 people systems hosts that use bridged networking on vmnet0.

  4th OS uses 255.255.255.0 and bridge over vmnet0, however

  I can not get on the net, can't even ping the gateway.

  Then the bridge vmnet0 manage two different subnets?

  Thank you

  Matt

  Yes, network bridge can have several subnets.  Bridged using, your virtual machine works like any other physical machine on the network.  So just as if two physical machines on the same physical LAN had different submet, they would not be able to communicate directly with each other, so also with your virtual machine having a different subnet.  With two subnets, you should probably two gateways.  If you cannot change the 4th VM subnet to match others, you would need a router between the two subnets.  (Again, same as if they were physical machines.)

• Replication of different subnet

  I need to configure the replication of an existing EQ group which has all of its interfaces on a subnet that is not routed; a newly staged group who will live in a different subnet.  Initially, the two groups will be co-located for staging, but the new group will be moved to a remote site, but retains the private address that it is affected.

  What is the best practice to configure replication?  I just need to allow the routing on the iSCSI networks?

  Yes, you need get the subnet that is connected to a router that will reach the remote site.   You set up default GW for iscsi is what is used for replication.  Replication between groups EQL is made via the port 3260 in an iSCSI session.

  Kind regards

• Communication of VLAN different using UME.

  Hi all

  I am a beginner engineer, so I have a bit of knowledge.

  I tried to configure it by myself, but something bothers me...

  I want you guys to help me!

  In fact, I configured BPMH using the switches (CISCO & DELL) 4.

  Please provide the attachment on the photo and the configuration of file (.txt) (I draw and scanned..)

  As you can see the picture, you will know what I want to configure.

  The point I want follows content.

  (855) 935-7526 *. I want to communicate with switches together.

  -online but, Dell 7024P communicates any other switches... I think awarding IP is 30 (192,168.10.91) vlan... others have

  VLAN 10 (192.168.10.x)

  In fact, he was very big problem.

  2. only Dell 7024P does not communicate with the Internet.

  Then, I set up static routing set of switches (ip route 0.0.0.0 0.0.0.0 192.168.10.94)

  But only 7024 P does not...

  To connect to the other, what can I do in 7024 P Dell switch.

  Thank you, Daniel C.

  See the CISCO3560, executed, stp.txt

  See the CISCO3750, executed, stp.txt

  See the DELL7024P, executed, stp.txt

  See the DELL8024F, executed, stp.txt

  

  The first thing that comes out of me, is that on the P 7024 30 VLAN IP address is in the same subnet as the IP addresses of 10 VLAN on the other switches. This creates a scenario on the Cisco and 8024 switches, where you cannot assign an IP address 192.168.10.x 30 VLAN. Because VLAN 30 does not have an IP address, it cannot be routed. The resulting transmission 7024 30 VLAN Tag traffic on port gi1/0/12 article. The CISCO_3750G receives traffic labeled for 30 VLAN, but then cannot do something with it.

  There are two approaches to solve this. You can assign a different subnet to the VLAN 30. Then on each switch assign an IP address to VLAN 30. Configure the switch for VIRTUAL LAN routing on your CISCO_3750G.

  http://bit.LY/1nECOCq

  Another option would be to not use 30 VLAN. Instead use 10 VLANS on the 7024 and VLAN 10 IP address assignment the 192.168.10.91.

  Once you have the IP gene outside model, then I do it with fine adjustment covering tree instances.  Here is a white paper with some useful practices and examples of UME use.

  http://Dell.to/1MrDPx4

  See you soon

• WLC and AP on different subnets

  I want to add a new access point to my existing controller. Currently I have about 15 AP is connected to one vlan separate mgt for the AP, vlan 10. It's shared resources for the controller and the other VLAN user as Private, Public, etc. WVoIP. I already started to implement EIGRP network instead of having a large layer 2 vlan would be network. In one of the more recent places I'm routing, I have a new AP to connect. I'm trying to make sure that this design will work before I implement. So I have a 3560 connected to my core 4506 with a 3 layer connection. EIGRP works as well. I intend to have the 3560 intervlan routing with vlan voice, data and wireless. The problem I see is how can I get the AP to speak with the controller as they are on different subnets, more a metro E 'WAN '? Any suggestion would be great.

  As long that the ROUND was started locally first, this TOUR will be the ip address of the WLC. If you want to fix the ROUND on a different subnet from L3, then configure ip helper-address the ip address of each wlc management. then configure the ip forward-Protocol udp world 12222 & ip forward-Protocol udp 12223 on the router of L3. This with the help of intellectual property, will allow the s TURN to join the WLC on the other end.

• With the help of several NIC in Win 7 - different subnet

  Can someone tell me the best way or the right way to configure two 2 Gigabit NIC in Windows 7 Ultimate?

  Map NETWORK 1 is currently used to access the INET and my FreeNAS server via a 192.168.0.x subnet. I would like to set up a 2nd NETWORK card to maintain a "static route" between this box (Win 7) and box of FreeNAS (OPT 1 is configured as a secondary NIC on the side of FreeNAS already).

  The static route will use the subnet 192.168.x.x with FreeNAS is 192.168.1.100 on the secondary card. The Win 7 box, I'm going to say... 192.168.1.3 for the static route NIC w / the same thing for GW and DNS.

  Is it possible that way, as mentioned above, or what I need to dig a little deeper. The static route will allow me to exploit the full potential (at least I hope) between 2 machines with regard to flow by a X-Over cable. This way I can put both sides higher than regular LAN depending on the parameters.

  I don't need to work, but rather a bit more than the flow of 20 MB/s when xfering large files recording studio. Yes... I know that FTP is not the best for xfering... I'm looking into SSH w/patch, SMB/CIFS or NFS

  Tim

  Your plan should work fine.  Specify a subnet mask of 255.255.255.0 on both network adapters to 192.168.0.x and 192.168.1.x different subnets.

  You do not need to specify GW and DNS on the secondary NETWORK, and you don't need to create a static route.

  To access the box of FreeNAS on secondary NETWORK map, use his IP (192.168.1.100), and not its NetBIOS name.
  Owner, Boulder computer Maven
  Most Microsoft Valuable Professional

• Problem with DHCP broadcast between VLAN

  Hello

  I trying to solve the lab that I set up, I have a problem with broadcast between VLANS with my DHCP. I looked around the vmware community to find my answer, but I did not who is right why I post here!

  So here's my situation :

  • ESX with 2 race of VM:
    • An R2 of 2012 Windows running a DHCP server with a configured scope
      • This virtual machine is assigned to the vmnic4 with the port VLAN 100 group
    • A Windows 7, which I use as a customer
      • This virtual machine is assigned to the vmnic4 with the port VLAN 110 group
  • Switch Cisco with a simple configuration:

  interface FastEthernet0/1

  Description LINK FOR ESX

  switchport mode trunk

  switchport nonegotiate

  interface FastEthernet0/24

  Description OF LINK ROUTER

  switchport mode trunk

  • Configuration of the Cisco "router on the stick:

  interface FastEthernet0/0.100

  encapsulation dot1q 100

  10.1.1.254 IP address 255.255.255.0

  interface FastEthernet0/0,110

  encapsulation dot1q 110

  IP 10.1.2.254 255.255.255.0

  IP helper 10.1.1.0

  
  

  The resolution of the problems that I did:

  • Affecting the client static IP and that both virtual machine can ping each other
  • Moving from the client to the same VLAN as DHCP server, and the DHCP server is to give the client an IP address.
  • Sniffing the packet:
    • I can see the client DHCPDiscover
    • I can see the router with the command "debug ip dhcp server packet" package passed on the 10.1.1.0.
    • I am not able to see the packets from the router to DHCP perspective

  That's why I guess miss me something ESX configuration.

  Thanks in advance for reading this post!

  
  

  PS: I've linked a vswitch configuration screenshot
  

  I think that you have configured an incorrect address of IP support, take a look at the following line:

  IP helper 10.1.1.0

  
  

  Your DCHP server is really 10.1.1.0? I think not, since 10.1.1.0 corresponds to the ID of the network 10.1.1.0/24 network.