Pavilion 15 bj000nh: very low wifi on the brand-new Pavilion 15 bj000nh

Similar Questions

• Toshiba NB520 - very low WiFi signal strength

  Hello

  My new netbook Toshiba NB502 has a signal strength wireless very low compared to the other two netbooks used in my house.
  I tried to play with the Device Manager but can't see any obvious way to improve the signal.

  Any advice?

  Hello

  Go to Win 7 power management settings and disable for the WLan to save energy.
  http://APS2.toshiba-tro.de/KB0/HTD12017W0001R01.htm

  Good luck

• HP ENVY 17 F9M14UA #ABA TS: no audio beats since the upgrade to 10. St very low volume of the same volume at 100%

  Walking to Windows 10.  Loss of my audio Beats.  The volume is very low, so even than the value 100% volume

  Hello:

  See if reinstalling the audio driver solves the problem...

  This package contains the driver that allows to the Audio IDTHigh-definition (HD) in models of laptops that arerunning an operating system supported.

  File name: sp63555.exe

• M40-285: very low contrast on the screen

  Hello;

  I have a new M40-285, and I found the screen with very little contrast. It always happens, even in the BIOS screen.

  On the lower side of the window, there is always a Flash of light, the background is never 'black', more like a gray.

  I got a M30X and the screen was crisp and Nice. That was the reason on the purchase of an M40.

  The laptop is brand new, I ask for a replacement, or something usual in this model? As I said, M30X screen was wonderful!

  Best regards.

  Hi Fran

  Satellite M40 is well-known for me because one of my friends has a. I can't really understand what exactly is going on with your laptop but try it please use the FN + F7 key combination to set the brightness of the screen up.

  If you are not satisfied, please contact your local dealer and check with him. M40 is a very nice unit with a fantastic design and I believe that there is no hardware problem, just a few bad display setting.

  Good bye

• call very low voice on the other side (Z5 MM Compact)

  Hello guys,.

  I have a question which appeared suddenly and wont go away.

  My voice is very low, on the other side, people say it's like I want to talk away from the microphone.

  There is no problem with voice recording or when using headphones. I already rebooted the phone but question keeps beeing there.

  It's as if the z5 lowers my voice through the microphone during a call, maybe it's the malfunkctioning of noise cancellation?

  So I had no time for the repair of software, but after upgrading to the new fw X.224 each mentioned last issue is resolved

• Aspire V 15 Nitro sound very low even when the value to 100%. Does anyone have a solution?

  Dear community,

  I tried clicking on the sound icon.

  By selecting "playback devices".

  Clicking Tealtek High Definition Audio, and then click Properties.

  In "Improvements" all I have is a box unchecked to "disable sound effects everything" and nothing else. so, I can't find anything to change.

  When audio is playing on the icon settings sound is 100%, but the green bar is only part of the lower part of the bar.

  The sound was working fine last week. I don't know what I may have accidentally made.

  I would like suggestions or ideas.

  Thanks D.

  Dear IronFly,

  Thanks for all your suggestions. I just found out what caused the problem. A recent update for the onboard sound of Acer apparently gave it priority over Nvidia. To give priority to Nvidia and then by restarting the computer, its a was restored in all its splendour. If all goes well, this solution can help people who have lucky on a similar problem.

• My laptop volume is very low, even with the maximum setting. It also has a very annoying echo

  I tried every setting available on this laptop, go all together if not try several changes in all settings. The volume is still low and has a very annoying reverberation and echo effect, even with these settings turned off. I got it for a week, and I was very happy with any other accept the audio. The reasons for buying this model were media processing and so far I have and become more disgusted daily with her. It is a Pavilion dv6 and it has beat audio software. If anyone has a solution, it would be much appreciated.

  Hello

  One thing that can help is the following.  Do a right-click the speaker icon in the taskbar and select "playback devices".  Left click the device once to highlight default (it is usually 'speakers and headphones') and then click the properties button.  Click the enhancements tab and put a check mark in the box "Loudness equalization.  Click on apply to save the changes and then click OK in all other windows and see if allowed at all.

  Kind regards

  DP - K

• Very slow WiFi on the 3G xoom with update 3.2

  Hi all

  Was wondering if anyone else has the same problem.

  I bought the unit a few days before and same day updated to Android 3.2 version. I use internet on my Wifi at home and have a Netgear - WGR614 router. Browsing speed is very very slow and do not open many of the sites.

  The intensity of the signal on the xoom is - (asu 3-105 DBM).

  Is this a problem with the Android 3.2 update or my wifi at home is low? I was able to reset the tab to the original version?

  any help is very appreciated.

  

• Satellite Pro 4600 - very low picture on the screen

  Guys, I really need help.

  I picked up on old satellite pro 4600 eBay and have rebuilt the thing - everything works EXCEPT the screen - I get a very small image, even on the start screen.

  So far I have - changed the cable lcd - no effect. changed the Panel itself, no effect and inverter (4 times!).

  Any suggestions? Driver problem? Setting I missed somewhere? Motherboard problem?

  Hmmm. My first thought was the faulty FL inverter.
  Are you sure you used the right and compatible FL inverter? A connect it correctly?

  What about the keys FN + F6/F7? It allows to set the brightness to a higher level?

  Then maybe you should check for this possibility.

• Signal low WiFi in the other room with Qosmio X 770

  I have a Qosmio X 770 3D
  Wifi signal problems.
  Wired router 62 Mbps when wireless near large router close to 50 Mbit/s. If I go down and he falls down to between 5 and 15 Mbps and loses the signal entirely on covers.

  When I try my laptop cheaper in the same circumstances I get 45 Mbps down constantly. Even my wife Notepad Gets the best signal strength.

  Channel selection makes no difference, except to make it worst when others use even.
  My broadband provider has replaced the router, come home and guarded point out the strengths and wrote its my laptop problems.

  The wifi card can be improved for a stronger reception. Moving to the upper range won't work as my other gear use 2.4.

  Any other suggestions please?

  > When I try my laptop cheaper in the same circumstances I get 45 Mbps down constantly. Even my wife Notepad Gets the best signal strength.

  Its no matter if the phone was cheap or expensive depend on the intensity of the signal on different topics.
  Above all it s is WLan/chip built in Notepad.

  So in your case I recommend you to check if a different use WLAN standard like 802.11 B / G or N would make a difference.
  I recommend also to check the energy saving settings map WLan.
  In the case that the laptop is used on battery, the system can drops down the WLan performance in order to save the battery.
  Also an update of the WLan driver can improve performance.

  However, as I wrote above: it s still a matter of smart WiFi

• HP3070A:printing (happy) box appears rotated at very low angle in the...

  HP3070A I bought this printer, but what print or photocopy... for example a page with the content with a border (to create a box), left, right, down, margin superior 20px in Crete a wide area of page, although the (happy) box appears rotated at very small angles so have... above for example top left distance top 17px and top distance correct top 20px (gold 21px i do not know exatly only the difference know 2-3 px left-right top border to the top of the page)... Well?

  as I say cannot correctly insert the paper in the tray, which is difficult for this printer this action, what should I do?

  This exact video for you, Ise. I hope this helps!

  http://goo.GL/B4M3R

• Set up a home network on a Vista computer. Added my XP computer on the network. I can go on the internet but the signal strength is 'very low' 98% of the time.

  I used a d-link WBR-1310 Wireless G router to set up the network on my Vista computer.  On my XP computer, I used an adapter G USB 2.0 Wireless d-link WUA-1340.  Both computers are single room apart and most of the time, the doors are open, so there is no major obstacle to interfere with the signal.  This is my first experience on the implementation of a network and I must admit I was a little unsure of myself.  I don't know if I have some incorrect settings or if the problem may be something else.  It is a WEP secure network but I don't think that's the problem.  My XP computer on the network automatically signs as soon as it starts.  I am trying to download the LLTP from Microsoft on my XP machine, but I don't know if this could be the problem.  I've been struggling with this problem for almost 4 weeks and I'm getting very frustrated.

  PLEASE, I WELCOME ANYONE WITH AN IDEA OF WHAT I HAVE DONE WRONG, TO ANSWER!

  I'm sorry, but I read your post and I do not understand what the problem is you want to solve.  Is something that does not properly?  If so, please give us the details: what you're trying to do, what happens when you do that, the text of the error messages, etc.

• Printer HP 6500 E709n - impression is very low, even after the new cartridges installed

  New cartridges installed correctly, and there is no error message. But now, the impression is almost unreadable it's so light. What is the problem?

  I understand that you are having problems print quality with low impressions.  I've included a useful document that might solve your problem.

  Let me know if it helps.

• HP Envy 15-k233ca Notebook: Wifi constantly falls on the brand new HP Envy laptop.

  I always thought that if highly HP and as such, has decided to buy a laptop HP - HP Envy 15-K233ca laptop.

  I had a few problems early and one in particular, makes for an unpleasant experience.

  The wifi connection continues falling.  It drops when the system is put into mode 'sleep', when I surf on the net and even after a reboot.

  I went through the question (and a few others) with HP tonight and after 2 hours assistance service has encountered the same problem.  I'm now having to restart the computer and solve problems to try to maintain a wireless connection.  This is my first experience with an HP laptop and I'm disappointed.  It's unfortunate, but I may have to return it.  I'll walk to Apple for a replacement.   If someone from HP can solve this problem for once and for all, it would be useful. Otherwise, I will have no choice but to return the unit.

  Note: I noticed that others are experiencing the same issue.  I asked that the HP help desk install drivers to fix the problem.  If this does not work after our session tonight, then I fear, that it may be a hardware problem.

  Hello

  Thank you for taking the time to answer.  It seems that the box was already unchecked.  Good idea look even if, as others may have this checked and may, if all goes well in this solution.  I asked a tech support in India for download drivers that may correct the problem.  It seems to have worked.

  Thank you once again.

  Madison.

• Want to 750 - xt 550 (CTO): Desktop problems Bang and Olufsen Sound of 750 - xt HP Envy with the brand-new office

  I bought a new system and it arrived yesterday, in the introduction, I have a 5.1 speakers Creative Labs system (which worked perfectly in my previous HP media center PC) I'm connected (using the catch green, black and Orange on the back of the system).  Using the Bang and Olufsen 'test' feature, I hear from "front speakers' (green connector), the Center and the subwoofer (Orange wire) no sound from the surround speakers (black wire).  The sound is HORRIBLE, roaring, low volume, just horrible.

  If I pass the black cable (surround) at the entrance to white (side speakers) I can hear the sound on the 5 speakers, it's always horrible and very, very disappointing!  I spent over 4 hours on the phone last night with HP Support who told me, in conclusion, that my system does not support sound 5.1, I will be able to use Stero (i.e., the Green connector).  My number is 3023344605, the discussion was just a mess.

  Can somone suggest please how can I get my sound working properly?

  I brought your question to the attention of a team within HP. They are likely to ask for information from you to get your information or product serial number. Please search for a private message from a contact HP identified. Also, remember not to publicly post information and series numbers.
  If you are unfamiliar with works as a private of the Forum messages, this post has instructions.