Pavilion dv7 1245 dx boot problem

Similar Questions

• HP Pavilion dv7-1245 ca battery internal error 601. How can I change the battery

  Hello

  My laptop is a Pavilion dv7-1245.

  It shuts down its own, and after a few minutes, she lights up and displays this error message when starting:

  HP battery alert-

  ... your internal battery needs to be replaced...

  Internal battery (601)

  Sometimes, I need to start my car.

  I bought it two years ago. I just program the hard drive a week ago, causing the original one crashed badly.

  Could you please tell me what specific battery should I buy?

  I read in another post for the Pavilion dv6 you just need to keep it pluged to replace intyernal battery like in a flaslight. Is it OK for my model?

  I would also like to know if the problem to cut down on its own, it is linked with the battery warning or if it is another question.

  Please notify. I use my laptop to work ar House, and I can't afford to buy a new one now.

  Thanks in advance

  Soledad

  Montreal, Canada

  Hello

  You just need to replace the internal battery.

  Here is the maintenance and Service of Guide for your specific model.

  On page 54-55 you will find instructions how to remove the battery and how to install the battery.

  Here you can buy a new one.

• HP Pavilion dv7 second HDD installation problem

  Hello

  I recently bought an internal WD7500BPVX 750 GB SATA HDD compatible with my HP Pavilion dv7 - 2030eV to be used as a second hard drive, since I already have a 250 GB HARD drive on the laptop. I also bought a SATA cable which I think is compatible and a caddy for the disc. When I connected the SATA cable and pressed the Start button the laptop powered upwards for about a second and then stop.  I disconnected the SATA cable and left only 250GB driver connected. When I turned on again your laptop booted normally. Once I tried to connect the new HARD drive again the same thing happened. Any ideas what might be happening? I checked two times for parts compatibility before you buy, but I can't rule out it as a cause.

  Thank you all in advance for your help.

  Hobistas wrote:
  

  Hello

  I recently bought an internal WD7500BPVX 750 GB SATA HDD compatible with my HP Pavilion dv7 - 2030eV to be used as a second hard drive, since I already have a 250 GB HARD drive on the laptop. I also bought a SATA cable which I think is compatible and a caddy for the disc. When I connected the SATA cable and pressed the Start button the laptop powered upwards for about a second and then stop.  I disconnected the SATA cable and left only 250GB driver connected. When I turned on again your laptop booted normally. Once I tried to connect the new HARD drive again the same thing happened. Any ideas what might be happening? I checked two times for parts compatibility before you buy, but I can't rule out it as a cause.

  Thank you all in advance for your help.

  Hello

  This series does not start with two different hard disks. If you want a second hard drive, you need the same 250 GB drive as the original to make it work.

• Pavilion dv7-4285dx: cannot BOOT/POST/VGA external and internal LCD is dead (cracked)

  I cracked the screen of my HP Pavilion dv7-4285dx so bad that I can't read anything on the subject. I'm trying to start to an external monitor to the VGA port, but never to get a signal.

  I tried the key switch monitor, but that does nothing. I tried to unplug the LCD internal of the motherboard - not different. I tried a CMOS reset by removing the laptop battery, remove the CMOS battery, cut the power and hold the power button / stop for > 1 minute, then by restarting with external LCD just attached, but STILL no video on the VGA port.

  The video card is OK, because it starts with Windows and then I have the video on the external monitor.

  Although it is good that I can use the monitor to post once Windows starts, I need to have the video when the BIOS starts to change.

  Does anyone have another suggestion how I can get the BIOS to detect and display external VGA at boot time?

  Hello Todd_in_LA,

  Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the Forums of HP, I would like to draw your attention to the Guide of the Forums HP first time here? Learn how to publish and more.

  I read your post about how you try to start on an external monitor, and I would be happy to guide you to a resolution!

  Based on the information provided in your post, I recommend you contact our technical support at the 1-800-474-6836. If you do not live in the United States / Canada region please click the link below to get help from your region number.

  http://www.HP.com/cgi-bin/hpsupport/index.pl

  I hope this helps!

  Concerning

• Pavilion dv7-6140eo: device Bluetooth problem

  Hello.

  I can't start bluetooth on my Pavilion dv7-6140eo with W7 (32 bit)

  Device Manager do not appear, only the unknown device.

  I was trying to upgrade the driver of all HP possible, but always the same.

  Can you help me with that?

  Fr.

  Andy

  Hi, Philippe:

  What wireless network card model is has your model?

  Who determines what bluetooth driver you are installing.

  This is probably the driver that you need for the unknown device:

  This will install HP 3D DriveGuard, which offers protection for internal laptop disk drive if the computer accidentally falls or suddenly hits another object. This package is available on mobile phones supported with supported operating systems.

  File name: sp53462.exe

• Pavilion dv7: replace the boot drive primary hdd2

  My flag has two hard drives. I cloned the startup disk (1) on the secondary drive (2). Now, I want to move the disc 2 in the main drive as boot drive Bay. What is necessary to achieve this. Is there the bios settings to change or identify the settings on the readers who need to change?

  N ° all what you need to do is physically swap posts. The method varies a bit between generations dv7 different but basically you remove cover license plate and Exchange readers, for one another. If you give us the exact model, we can probably find illustrated instructions and maybe even a video.

  Only in the Bay of primary is bootable, which serves as a fail-safe.

• My HP pavilion DV7 1245 x with Vista has stopped recognizing the CD.

  When I put a DVD/CD player and click on the disc or the player open, it is said, please insert the disc in the drive.  When I put a CD inside whirs for a little while but when I put a DVD in nothing happens at all.  When I ran FixIt it says fair-media is not readable, but I tried all kinds of DVD and none of them work. Can someone help me establish the popular terminology? I already deleted and reinstalled the driver several times and run Fix It twice. Thank you!

  Hello

  Check the diagnosis with the help of HP, their documentation online, and ask in their forums
  on known problems.

  Support HP & drivers
  http://welcome.HP.com/country/us/en/support.html

  Contact HP
  http://welcome.HP.com/country/us/en/contact_us.html

  HP forums
  http://h30434.www3.HP.com/PSG/

  ====================================================================

  You have disk problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD burning and)
  Playback of CD and DVD). So it is not unusual for parts from 1 or 2 to not work so that others do
  correctly.

  A CD/DVD cleaner might help.

  Brand of the CD or DVD drive can also be the problem. Low quality (cheap brands) are always problematic.

  CD/DVDs have a tolerance + - and your can read/write on the edge outside these discs
  tolerances. They may be delivered, but it is generally more economical to replace the disk.

  Several good info here:
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  Notes on the troubleshooting and repair of readers of compact disks and CD-ROM Drives
  http://www.repairfaq.org/repair/F_cdfaq7.html#CDFAQ_014

  ===========================================

  This troubleshooting could not help if there is alignment and/or wear issues however it
  a shot.

  Step 1: Please do all the same underneath if you did some before as is often total
  a process that solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
  Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
  RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
  below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a coward
  cable or slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  Try this fix manually if the Fixit 314060 does not work
  http://www.pchell.com/hardware/cd_drive_error_code_39.shtml

  Your CD or DVD drive is missing or is not recognized by Windows or other programs-
  a Mr Fixit
  http://support.Microsoft.com/kb/982116

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
  for Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error in Windows
  Vista installation after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  ===============================

  Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
  Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
  do it right.

  Did you follow the Troubleshooting Guide for the reader who still does not work? There are
  the entries in registry that the troubleshooter does not solve and those who "might" be the cause.

  Check with your Maker system and a device for the two possible firmware updates and
  the correct registry entries for your car.

  Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
  as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
  the parameters.

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  -----------------------------------------------------------------------

  You can probably find more info here and maybe even the exact registry for your CD/DVD settings
  drive from someone with the same model.

  Forums - a lot of expert real help
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
  nothing change) - find the DevManView device and then make a right click on it free in RegEdit.

  DevManView - free - an alternative to the standard Windows Device Manager, which displays all the
  devices and their properties in flat table, instead of the tree viewer
  http://www.NirSoft.NET/utils/device_manager_view.html

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">

• Skype on Pavilion DV7 Vista and Win7 problem

  I have problems with Skype 5.1 - when I try to open it a message appears 'Skype has stopped working, check online for a solution and close the program, etc.'. Nothing is displayed when clicked. I tried searching for virus & update drivers without success. My DV7 was initially running Vista so I decided to do a new install of Windows 7. To my surprise, the problem with Skype persisted, so I can only assume it is hardware partner. I've updated the Bios without success.

  I found a partial solution - start Skype in Win 98 / ME compatibility mode. Skype opens but the video & audio quality is poor. I have Skype installed on 2 desktops with Vista & Win 7 & it works perfectly, so the fault must lie with my HP laptop. Any help would be appreciated.

  Update: if I disable video IDT Audio Device Codec drivers Skype works well (in Win98 / ME compatibility mode) without sound. This suggests that the audio drivers are the cause of the problem - there are several posts on this topic. I tried to install an older driver (6.10.6225.0 instead of 6,10 6276.0) but the program crashes still after a few minutes on a call for the use of the CPU to 85-90%. My machine is the DV7-2030ea with a processor AMD Turion 2.2 GHz, 3 GB RAM, ATI Mobility Radeon HD 4500/5100 graphics & AMD HD Audio. Someone else had this problem?

  Tried Skype 5.2 - reluctant to install & video out does not work. Decided to return to 3.6 (360216). Only works under Win 98 / Me compatibility, but No problem with the gel etc even mode after 30 minutes. Anyone with problems above with DV7-2030ea or similar machine spec, I would say:

  (1) use Skype 3.6 instead of a newer version.

  (2) run in Win98 / Me compatibility mode.

  (3) if the problem persists, replace IDT HD Audio Codec drivers with those of Microsoft.

• Pavilion dv7 1270 ca display problem

  I went through Vista and changed the size of the program display.

  It's so great now I am unable to change it again as it apply

  the button is out of view and inaccessible.  Please, can someone help me

  get this problem resolved

  Hello

  See this link.

• Pavilion dv7 - 4263cl: hard drive problems

  Long story short, OS could not start windows with a missing BOOTMGR message, recovery disc, not work, ordered new HP recovery disks.  To cover, I ordered a new hard drive to replace it, with the same characteristics but a 1 Toshiba to.

  OK, installed the hard drive and used recovery disks at HP, but when you restart always get BOOTMGR missing error message.  Make a new recovery disk for windows 7 64 bit internet and serious on a bootable CD.  It starts, but found recovery does not list an OS system on hard drive.   Did the hard restart more once, install hardrive checked again, the cables and connections.  Took another installation of the HP recovery discs and also led a bootable disc that was to fix the problems with installing a new HHD and activation of the HHD working properly. Working always nothing. Get the same message.  Cast recovery manager got into the prompt orders and done a repair of the bootrec nothing / new. Checked the directory and found at the bottom of the list that it lists zero OS System.  So, how can I get my hard drive formatted to accept the installation of the OS? Any ideas to try, I have read and tried all the messages, I could very well on this forum.   Thank you...

  Thanks for the reply, yes my hard drive failed and I installed a new one, but after using the purchased HP recovery disc though HP, showed that a black bootmgr error saying screen was missing.

  Found on the HP disks partitioned hard drive, with windows on X:\ but was again start-up C:\ which was just a recovery image.   X drive was not complete, he lacked all the drivers and could not activate or change and C disc drive letter. I didn't know how to do this in the command prompt.

  Fixed my problem with a windows 7 installation no disc not the recovery disks that came from HP, if all goes well, they will work to reinstall all drivers to the laptop, but we'll see.  Used (computer repair) on the installation disk and it repaired the bootmgr.  Thanks anyway...

• HP Pavilion dv7/entertainment - Ethernet connection problem

  The computer was always well connected to wireless networks, but I moved to a new place and can't get my computer to connect to the internet. I ordered a former gateway wireless via amazon but sent back because I thought that the antenna did not work. However, now I am trying to set up internet via an ethernet cable and cannot.

  I tried two different cords ethernet without a bit of luck. Google research, I determined that there should be LED lights next to the port (?) Ethernet on the computer, but there is not all the lights on with a rope. I have tried countless attempts of troubleshooting and many "patches" of others, but nothing has worked. I even uninstalled and reinstalled the driver software of all the network/internet conncections via the HP Web site. I can't get the internet to work!

  I am currently connected to the personal hotspot that produced my phone, but I can't sustain that without exceeding data limits cell.

  Any help would be greatly appreciated!

  Hi, thanks for your answer!
  After all a lot of trouble, I have established that BOTH the router I purhased and the Ethernet cord I was good did not work properly! (The antenna on the router is malfunctioning and was working as the Ethernet cable when at a specific angle, which is why it seemed to work at first, but not after other attempts). I have since been able to get a new router and an Ethernet cord and am happily connected to Internet.

  Thanks again!

• HP Pavilion DV7 1451NR - drivers installation problem

  I installed the drivers and I installed AMD M780G first, followed by all the others.   I was told is AMD M780G chipset, so it was the first that I installed.  I installed all the drivers listed for this computer after that who did not appear on this Web site.  Its still does not I added the photo here to view the error I face.   Any thoughts?

  Thank you!!!

  

  Hello:

  Try the graphics driver directly from AMD and see if it works.

  http://support.AMD.com/en-us/download/desktop/legacy?product=legacy2&OS=Windows%20Vista%20-%2064

  The ethernet controller needs this driver...

  This package contains the Realtek Family PCI - E Fast Ethernet NIC Driver for laptop models supported and operating systems.

  File name: sp45181.exe

  One of the unknown devices probably has this driver...

  http://h20565.www2.HP.com/hpsc/SWD/public/detail?sp4ts.Oid=3688870&swItemId=ob_81492_2&swEnvOid=2103

• HP Pavilion Dv7: No boot device error * HELP *.

  I have an old Pavilion dv7 laptop that does not start because he apparently didn't quite "bootable devices." I looked this error online and once I opened it upward, I discovered that whoever worked on the last laptop didn't turn screws from the hard drive hard drives seem to be correctly connected but my question is, is this the problem?

  Any help would be appreciated!

  Full of error: (Black screen)

  Realtek PKU Express Gigabit Ethernet controller series v2.26 (090219)

  PXE - E61: Media test failure, check cable of

  PXE - MOF: Exit PXE ROM.

  No boot device - insert boot disk and press any key

  ~ Carbender

  Carbender wrote:
  

  I have an old Pavilion dv7 laptop that does not start because he apparently didn't quite "bootable devices." I looked this error online and once I opened it upward, I discovered that whoever worked on the last laptop didn't turn screws from the hard drive hard drives seem to be correctly connected but my question is, is this the problem?

  Any help would be appreciated!

  Full of error: (Black screen)

  Realtek PKU Express Gigabit Ethernet controller series v2.26 (090219)

  PXE - E61: Media test failure, check cable of

  PXE - MOF: Exit PXE ROM.

  No boot device - insert boot disk and press any key

  ~ Carbender

  First, take out the HARD drive and put the screws to the right to maintain and replace the HARD drive and reboot again. It could be that the missing screws causing the HARD drive vibrates too and make the heads and causing the HARD drive having problems.

• HP Pavilion dv7 Notebook PC - Windows Boot Manager does not allow me to restart the laptop

  HP Pavilion dv7 Notebook PC
  XH121UA #ABA
  Office home and Student 2007

  I turned on my laptop and got the following message is displayed:
  Windows Boot Manager
  Windows could not start. A recent hardware or software change might be the cause. To solve the problem:
  1. Insert your Windows installation disc and restart your computer.
  2. choose your language settings, and then click "next".
  3. click on "Repair your computer."
  If you do not have the disk, contact your system administrator or computer manufacturer for assistance.
  File: \Boot\BCD
  Status: 0xc000014c
  Info: An error occurred trying to read the boot configuration data.

  I had no problem before now with the computer. Yet once, this message has occurred during a turn on my laptop. I tried to restart the laptop, but it is not allowing me to restart. The laptop back to this message.

  I appreciate any help with this issue. I thank very you much for your time and knowledge.

  Hello

  If you do not, use another PC to create a rescue CD Windows 7.  Download the ISO relevant among the links below.

  Windows 7 32 bit

  Windows 7 64 bit

  You must use an app like ImgBurn to burn the ISO to a CD - a guide on the use of ImgBurn to write an ISO on a disc is here.  One time created, or if you already have this, typing away at the esc key when you launch Notepad to open the Start Menu.  Insert the rescue CD.  Select boot options (usually f9), use the arrow keys to select the CD/DVD drive and press ENTER.  You can also get a prompt to "Press any key to" continuous - it if requested.

  When loading, select repair your computer and choose the command prompt.  When this charge, enter the following commands and press on enter after everyone – including spaces as shown.

  Bootrec.exe

  bcdedit/export C:\BCD_Backup

  c:

  Boot CD

  BCD attrib s h - r

  Ren c:\boot\bcd BCD.old

  Bootrec /RebuildBcd

  Bootrec /fixmbr

  Bootrec /fixboot

  Remove the rescue CD and try to restart the laptop.

  Kind regards

  DP - K

• HP Pavilion DV7-4190us screen after login problems

  My system has a dual boot with Ubuntu 12.04 and Windows 7 Ultimate edition. When I connect to Windows, I get this screen

  This does not happen when I boot in safe mode or when I boot on Ubuntu. I tried to disable all startup, running Memtest and chkdsk, but nothing seems to work. For now, I installed the latest driver AMD Mobility in the hope of it settle things. Does anyone else have suggestions for me?

  Al Merci ot.

  Closing. True isolated problem.
  http://h30434.www3.HP.com/T5/notebook-hardware/HP-Pavilion-dv7-4190US-AC-power-grounding-my-motherboard/m-p/1759437#M78612