Pavilion dv7 VM23UA #ABA: different Pavilion dv7 configuration of manual

Similar Questions

• Pavilion p100dx: need to HARD disk for my pavilion p100dx configuration

  Hello team,

  Recently my hard drive of the laptop broke and now I need to replace my hard drive P100DX Pavilion.

  To do this, I want to know the configuration of HARD disk as

  1. 2.5 or 3.5
  2. What is SATA or SATA-no?
  3. SATA is compatible for it?
  4. What is the size of the HARD drive that needs to be? -height, length and width.
  5. Seagate HARD drive would be compatible.
  6. pointers for the HARD drive to buy.

  Thanks in advance.

  Hello

  It's a laptop HP Pavilion 15-p100dx ?

  http://support.HP.com/au-en/document/c04463224

  If Yes, then

  1. it uses standard 2.5 "HDD.

  2. it is a SATA HDD,

  3 SATA III (or 3) and SATA II (or 2) is compatible.

  4. all standard HDD laptops would use the same width and length, thickness (hright) can be varry slightly, but your laptop supports 7 mm or 9.5 mm. Better use 9.5 mm because you don't need a frame fill to increase his height.

  5. Yes, HP doesn't produce HARD drives for laptops, it uses Seagate, Toshiba and a few other brands.

  6. you can buy in any computer store BestBuy or Amazon, Newegg...

  Kind regards.

• 783c, Pavilion, original configuration

  Hi all, would like to thank everyone in advance for their help.

  I am so frustrated with this endevor I could pull my hair.

  In short, I'm looking for a link so that I could download the original software/applications that accompanies this machne. I am also interested in finding a machine owner's manual. I would like to find the specs for this machine so I could for max the ram out and rebuild its original compliment/software.

  what I've done.

  I searched on round and round and round and round and round (where the frustration) HP support sites and nothing found on this machine. I'm serious, according to HP this machine does not exist (you want to see a picture of him?).

  product automatic detection tool identifies the machine but can't find any information on this subject.

  When I do a manual search for the model number is not listed.

  HW BOM 101

  BOM SW NA80

  System number P9924A

  S/N {removed privacy}

  HP Pavilion 783c model

  I managed to get windows xp home sp 3 above (works pretty well).

  as near as I can tell it has still all original hardware components.

  P4 2.53GHz

  512 MB of ram

  Thanks again for your help,

  Chris

  Here is a link to product support portal for your desktop PC.  Here are the specifications. Unfortunately the RAM maximum supported on this PC is 1 GB. The motherboard and interfaces are about five generations behind current standards of today's PC. It won't be easy to find parts to upgrade for the PC.

  The original software must be on a disk that came with the PC, age of ten years.

  There is a picture of the PC on the support portal.

• Pavilion 15-P001TX: RAM manually installed in the laptop

  Hello.

  I have a laptop HP Pavilion 15 - P001TX, which has 4 GB of RAM, integrated into it. Recently I realized that for the purposes of my work, the 4 GB of RAM provided is not enough for me, so I want to buy another 4 GB of RAM and install it into my laptop, my 8GB memory total. In this regard, I have a few questions:

  1. can I install the RAM manually by opening the Panel of the laptop inside of myself? There are several slots of RAM for my laptop?

  2. doing so Will void my warranty?

  3. If my warranty will get Sub, can I buy a new RAM and ask the people of HP's service center to install it for me?

  4 RAM which company will be more suitable for the model of my laptop?

  Thanks in advance.

  Kind regards

  Rishi.

  Here is the Service Manual:

  Manual

  See pages 106-117 for the installation of the memory. It requires the removal of the motherboard and puts at risk the warranty.

  On page 3, it shows that the Intel models have only a slot of memory. I think it's probably true for the lower end of Intel models and yours is an i5 so I think that yours has 2 slots memory I can't find documentation so you be sure had better assume she's a. So to have 8 concerts would require the purchase of a module of 8 GB.

  HP part number:

  Module of memory of 8 GB 670034-005

  http://www.Amazon.com/HP-693374-001-1600MHz-PC3L-12800-memory/DP/B00G2F3I4W/ref=pd_sim_sbs_147_6?ie=UTF8&refRID=0F6ED1G94P46SD4A2NPS

  Where do you live (single country) as this can impact your HP support options. I heard, in some countries, the Service Center will install memory that you buy from them if the laptop is still under warranty.

  If it's 'the Answer' please click on 'Accept as Solution' to help others find it.

• Pavilion N5415: Source for manual

  Is there an archive for manuals for old HP laptop computers?  First question: How do I turn it on?

  You can always find them on the internet

  http://www.manualslib.com/manual/359121/HP-Pavilion-N5125.HTML?page=10#manual

  Not your exact model, but the layout on the N5000s is essentially the same. Switch power is above the upper-left corner of the keyboard and a switch to cursor... slide laterally to get the computer to turn on. Once, I've owned a N5425 then I vaguely remember it.

  If it's 'the Answer' please click on 'Accept as Solution' to help others find it.

• Pavilion dv7 E: abbreviated DST has no hard drive 1

  Product number: LW039EA #ABD

  My PC starts, but after a few minutes becomes extremely slow. The memory test was OK, but abbreviated failed DST pointing Hard Disk 1 if an error occurs. Failure ID: 9LNGGF-5K77S6-MFH14J-60QV03

  I have 2 HDD, each with 750Go and it seems that disk 1 is a failure.

  (1) how can I remove the disc 1, which seems to be the MAIN (System) drive and continue to use only disc 2? or

  (2) if I need to buy new HARD drive to replace the failed disk 1, please advise that you buy and please provide detailed replacement procedure, to keep my data and OS.

  Initially, my PC was purchased with Windows 7, but I recently ugraded to Windows 10.

  Thanks in advance!

  See page 56 of the manual here:

  Dv7-6000 series manual

  Since you have 2 hard drives, you have a built-in spare part but you will have to swap positions that only the hard drive in the Bay of primary is bootable and can be the operating system disk. If you have data on the secondary drive, you must store it somewhere if you want to keep it. Because you can always boot from the primary drive, I would say that your data is safe on this subject, but you want to stop using it as soon as possible. You try to use the wrong disc you will have problems. If your laptop computer has been upgraded for Windows 10 and it shows "activated" in the information system, you can reinstall Windows 10 as a clean install and it will show as "responsive" when you connect to the internet. You can use the media Windows 10 tool to do a full installation disc Windows 10.

  http://www.thewindowsclub.com/Windows-10-media-creation-tool-create-installation-media-upgrade

  You can also see this as a sign that it is time for one SSD drive. Tomorrow being Cyber Monday you will find the best opportunities out there on the semiconductor readers right now.

  http://www.Newegg.com/product/product.aspx?item=N82E16820228135

  This is just one example; a concert of 240 for $55. If it were my laptop I installed an SSD in the Bay of primary and run Windows from it. Normally, I would advise that you can clone the old drive to a new drive, but with errors on the old disk, it would not be a good idea to try to clone. Let us know if you have any other questions.

  If it's 'the Answer' please click on 'Accept as Solution' to help others find it.

• Do help me to find the XP drivers for HP pavilion dv 6408nr laptop!

  Hello! I have a problem with my laptop! Using Windows Vista on it makes it work slowly, extremelly slowly! I tried different ways to configure, but it does not work properly! That's why I decided to replace Vista on XP, but I encountered a serious problem: there is no audio, video and other drivers for my laptop from the HP site! (((I don't found drivers via net either! That's why I ask your help to try to set up this problem! Maybe someone has a greeting! I'll be highly appreciated to someone who can resolve this collision! My laptop run under AMD processor!

  All the drivers you need (and more) are on DV6000Z cto page HERE

  First Nvidia Chipset installation and reboot before other drivers. For audio, MS UAA with another reboot before Conexant.Others you need can be done in any order.

• Pavilion G7 DVD replacement

  I need to replace the DVD drive, but can't get off the service Panel. This is different than that of the manual online.  I only have a screw instead of two, and it won't lift like the one shown in the manual.

  I did a search, but the solutions I found still doesn't let me down the back.

  Hello

  Please find the link given below might help manual & video.

  Video

  Manual

• 32L4333DG TV - need help with configuring WLAN

  I bought a flat 32L4333DG of Toshiba, but cannot configure the wireless connection.
  Help me please.

  Message was edited: assignment has been translated

  What's the problem? Have you read the instructions in the manual how to connect WiFi TV?

  There are 3 different methods to configure the WLan configuration:

  _1) easy Setup (WPS) _
  + If the AP is WPS compatible, this method can be used. +
  + WPS is a standard of the industry, designed to facilitate the wireless LAN connection and security settings. WPS automatically configures all the wireless settings. +
  + NOTE: WEP encryption is perhaps not able to configure through easy implementation. +

  _2) assisted Setup (installation using notification s AP information) _
  + Name network, authentication and encryption are decided according to the information provided by the AP. You can manually set the security key. +
  + The security key must conform to these conditions: +.
  + TKIP/AES: ASCII 8-63 or 64 Hex characters +.
  + WEP: codes ASCII 13 5 or 10 or 26 Hex characters +.
  + There's a key ID to set for the WEP encryption. +

  _3 _) manual configuration (manual entry of all parameters)
  + Some types of encryption are only compatible with specific authentication types. +
  + When authentication is an open system, only WEP or none is compatible. +
  + When authentication is shared key, WEP is compatible. +
  + When authentication is WPA - PSK or WPA2-PSK, TKIP or AES is compatible. +

  + When the inconsistent authentication/encryption pairings are detected, a warning message will be displayed and no connection attempt will be until the conflict is resolved. +

  + There's a key ID to set for the WEP encryption. +

• The proSafe (JGS524E + GS116E) Switches: Configuration Management Web GUI in VLAN specific

  Hello

  I use a JGS524E and a GS116E. The two are connected via a 802. 1 q uplink with all defined VLANS in him.

  A 802. 1 q other interfaces goes to a pfsense firewall, which serves as a router and dhcp server for each VLAN that I use.

  How can I configure the switches plug are in one VLAN specific and get his IP address of the dhcp server in this VLAN?

  At present, it seems to be random access: it is not predictable that range from intellectual property, it takes its IP configuration via dhcp...

  How management function works internally?

  Thank you

  Markus

  Hello

  Thank you. I tried it out, but the behavior seems to be a little different:

  I configured a static IP address for the switch (10.1.0.13 / 24). I have access to the switch web gui via the ip address of the host of a host directly connected (connected via a trunk port, where I put 1 VLAN on the trunk), but it is all the same, what VLAN that I use:

  When it is connected to the VLAN 1 I have access, but also through 10 VLANS, VLAN 20 and so forth (assumed, I configure my computer appropriate staticly in the IP network, for example 10.1.0.20 / 24). So it seems not be limited only to the VLAN 1. You have access to each vlan, only the IP configuration must be in the same network.

  I'm not sure, how it behaves when cascading the two switches, I have not tried.

  If this information can be useful for other users with the same question about this switching product line.

  For me, this behavior is not very well implemented from my point of view. For security reasons, you must limit access to the administration, for example by allowing access from a specific hardware port or a vlan. With the effective implementation, centralized management for a cascade topology is not easy to set up, perhaps because the behavior is not very clear and not documented in the manuals.

  Mentioned on the edge: there is no available TLS/SSL encryption when accessing the web gui (not https). So the password is transmitted in clear text... not a very good idea, I think.

  Thanks a lot for your help.

  Best regards

  markusd112

• System API for Configuration management configuration

  Hi all

  I've been playing around with the API system configuration for now a bit and I see it as a great way for companies to use as part of a management of global configuration utility. For example, if a customer wishes to put in place a new rack test with the same alias configuration, hardware and software OR installed then the API system configuration helps with most of this. I have already created a simple utility that can be used to query the currently installed hardware (of a local or remote system) and then programmatically rename aliases based on a file loaded configuration or manual entry. Similarly, the import/export of MAX features can also be used. My application of this would be mainly non - RT and for most of the PXI products, but a good design could work for both.

  So, my question to the community is actually on the side where I did not use the API of the System Configuration, but that makes a request of the software installed on a system. The software querying functionality of the Configuration API of the system is really only targets of RT and not the controllers based on Windows-oriented. I would like to be able to export a list of the software/drivers installed on an older system and then compare it with what is installed on a new system to make it easier for customers to determine if they have everything you need. I know that the export of MAX or the report has a list of installed software, but is this analysis of the best way to get the software installed (it's a beast of a file)? Someone at - it a better method?

  Kind regards

  Not sure if the VI attached will work across different Windows operating system because it uses a powershell command and I don't know how well the used command will work in all 32/64-bit applications... But so far this small VI I came with is the software I want to interrogate. I hope that it is useful for others and, as always, suggestions for improvement are welcome!

• Configuration of VLAN 6248 - link IP subnet to the VLAN

  We have 200 node network with no VLAN (small private company that developed quickly)

  All nodes / devices / etc. of PCs spread evenly over 6 Dell 5448 switches with no regard for the Department, location or usage.

  (1) L3 is 6248 - we've added 6248 route VLANs (everything is on VLAN 1 still - i.e. without marking)

  (2) L2 several VLANS by switch - the best of cases, 2 VLANS by 5448

  (3) trunk / general uplink L2 s 5448 using LAG (44, 45 ports) - should be labelled all traffic, but since it will be a conversion / migration on an e-commerce network 24 x 7, we thought that we would have to do uplink between 5548 s and 6248 General and changes to the trunk later

  (4) for the conversion, all uplinks of trunk/general will have several VLANs marked as vlan1 untagged traffic

  (5) we know fixed us every VLAN gateway IP to the IP address of 6248 maintenance the VLAN, but can't decide how to proceed with no one-to-one correspondence of VLAN LAG uplink

  Questions on 6248

  Q1: we would use "bind the IP subnet to the VLAN ' the 6248 to configure routing between VLANS or do we define the belonging to a VLAN by LAG?

  Q2: would we be able to ping the IP of the bridge VLAN configured in the 6248 a down host link / node / PC marked for the same VLAN?

  Any suggestions would be most appreciated.

  On the 6248 allowing to the VLAN routing you must just ensure each VLAN has an IP address assigned to it:

  Console (config) #interface vlan 5

  Console (config - vlan) #ip address 192.105.1.1 255.255.255.0

  Then enable routing on the switch:

  Console (config) #ip Routing

  That's all that needs to be configured on the 6248 for VLAN routing to work. One thing to take steps, is that on the 6248 the management VLAN is not routable. By default, the management VLAN is VLAN 1. Two options are to move the management VLAN a VLAN different:

  Console # configure

  Console (config) #ip address vlan 99

  Or not use VLAN 1 at all. Place traffic on other VLANs.

  The answer to your second question is Yes. With the VLAN routing enabled a customer to any what VLAN should be able to ping the gateway of the 6248.

  When it comes to generals and trunk mode. General mode is like a combination of access and trunk, you can send several VLANS not identified. General mode is most commonly used on the 6200 switches when connecting with the new switches, trunk sometimes doesn't connect when it is connected to a most recent switch. I suggest using the general mode on the 6248 and if it works, leave it in general mode.

  Here is a list of various white papers which all have some good info to have.

  http://en.community.Dell.com/TechCenter/networking/w/wiki/2580.networking-whitepapers.aspx

  6248 user's Guide

  FTP://FTP.Dell.com/manuals/all-products/esuprt_ser_stor_net/esuprt_powerconnect/PowerConnect-6248_User%27s%20Guide2_en-us.PDF

  6248 cli guide

  FTP://FTP.Dell.com/manuals/all-products/esuprt_ser_stor_net/esuprt_powerconnect/PowerConnect-6248_Reference%20Guide_en-us.PDF

  5548 user's Guide

  FTP://FTP.Dell.com/manuals/all-products/esuprt_ser_stor_net/esuprt_powerconnect/PowerConnect-5524p_User%27s%20Guide_en-us.PDF

  5548 cli guide

  FTP://FTP.Dell.com/manuals/all-products/esuprt_ser_stor_net/esuprt_powerconnect/PowerConnect-5524_Reference%20Guide_en-us.PDF

  Having to update firmware of the switch can help with interoperability.

  6248

  http://www.Dell.com/support/home/us/en/04/product-support/product/PowerConnect-6248/drivers

  5548

  http://www.Dell.com/support/home/us/en/04/product-support/product/PowerConnect-5548/drivers

  See you soon

• ASA with different failover module IPS

  Hi all

  Is it possible to configure the failover of the ASA with different IPS module configuration because we have: ASA 5585-X with firepower PHC-10 and ASA 5585-X with IPS SSP-10

  Thank you

  N °

  Inventories of material (basic unit, memory and optional modules) must be the same in a pair of failover ASA.

• Configuration Cisco 1905.

  I have a facility where the client uses 1905 router to access the Internet. They have a local network with 192.168.1.0/24 segment and a segment of WAN of 150.129.126.168/29 provided by the ISP.

  Currently, they use a D-Link router for internet access and his works fine. But when we use the Cisco router with config below, users are unable to access the internet.

  Cisco config:

  gi0/0---192.168.1.1/24 (LAN) interface

  interface gi0/1---150.129.126.170/29 (WAN)

  IP route - 0.0.0.0 0.0.0.0 150.129.126.169

  Pool DHCP - 192.168.1.180 to 192.168.1.199

  Now, since we use Pvt Ip in the network segment local and Public WAN, I feel that we must run NAT for users to access the internet. But not quite sure how to do it.

  Any suggestions and help in this regard would be highly appreciated :).

  Hi chinmoy.boruah1,

  You can use the following commands:

  R1 (config) #ip - 7 standard access list

  R1 (config-std-nacl) #permit 192.168.1.0 0.0.0.255

  R1 (config) #ip nat inside source list 7 g0/1 interface overload

  R1 (config) #interface gi0/0

  R1(Config-if) #ip nat inside

  R1 (config) #interface gi0/1

  R1(Config-if) nat outside #ip

  If you need more information about the different ways to configure nat this will help you to:

  http://www.Cisco.com/c/en/us/TD/docs/iOS-XML/iOS/ipaddr_nat/configuratio...

  Hope this info helps!

  Note If you help!

  -JP-

• PS shows two different colors under the same

  I have the 61BEBF and the 28BEBF in color Adobe and I try to import them to PS and they look on the screen of the same color. It is not a monitor problem, because Adobe color, I can see the difference between the two colors. What can I do?

  You must realize that the hexadecimal notation is meaningless without reference to a specific color space.

  Hex is not different from RGB - the same number will produce a different color in different color spaces. And conversely, the same color will be different hexadecimal numbers in different color spaces.

  Hex was invented before the modern color management and the concept of the color spaces. The only color space, you had back has your monitor, which is of course different from the configuration to the configuration. Then hex has been designed as a convenient method to designate the monitor values. There was never any pretext of accurate color fidelity.

  Today, we have something much better and hex is really outdated and obsolete.

  I suspect that the reason why it has survived for so long, that is that it sounds very "computerish" and geek, and so people incorrectly assume that it has a special meaning. This isn't.

  Get used to working with the RGB values in the color spaces defined and specific. For the web, this would normally be sRGB.