PC sees not device

Similar Questions

• Windows media Microsoft Quickplay sees not dvd disc

  Title: original dvd plays not
  Windows media Microsoft Quickplay sees not dvd disc, running on windows7 home premium service pack 1

  Hello

  1. don't you make changes on the computer before the show?
  2. you receive an error message?

  Method 1:
  Run the fix it and check.
  Hardware devices do not work or are not detected in Windows
  http://support.Microsoft.com/mats/hardware_device_problems/en-us

  Method 2:
  You can try the steps in knowledge base article and check.
  Your CD or DVD drive is missing or is not recognized by Windows or other programs

  http://support.Microsoft.com/kb/982116

  Note: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry in Windows:
  http://support.Microsoft.com/kb/322756

• I have vista 32-bit, he sees not my new drive hard hitachi, in device manager it shows that it works correctly?

  Why my expoler does not see my new drive hard when it is in the device as o.k. Manager.

  Look for the drive in computer management, it may need to assign a drive letter.

  Change, add, or remove a drive letter
  http://Windows.Microsoft.com/en-us/Windows-Vista/change-add-or-remove-a-drive-letter

• Connection to New [NOT] device every time

  Whenever I go to the support forums I get the message "your ID Apple is used to connect to a new device" even if I signed this device several times before.  I have also in this message "Enter this code to check on your device to connect", but invariably this verification code is incorrect. In order to get the correct verification code, I have to go find my iPhone (and hope that it is on and not in airplane mode) and the code that allows him to enter my other camera (one of my macs or my iPad).

  It makes no sense at all!

  (1) what is the purpose of this [bad] code sent to the device, with which I am trying to log in?

  (2) I do not use my iPhone all that often, it is not always with me, and it is not always on.  Why, in both that user, apparently I keep my iPhone with me just to log in here?

  The device/computer appears here?

  Apple ID - manage

  There is a contact link.

  Apple ID support

  Apple ID support (2)

• iTunes not devices of recognition

  Since I upgraded my computer to Windows 10, iTunes does not recognize my iPhone or iPod.  I have uninstalled and reinstalled iTunes twice, a factory reset on my phone, and still nothing will work.  It does not appear as there are drivers for the devices, but I'm not a computer expert, this is just a guess.  I went through research of breakdowns described on the Web site, and that didn't work either.

  Any advice on how to proceed?

  Thank you!

  I also have this issue. Help! Need to backup my devices before I risk update iOS

• FindResources return not device

  Hello

  Me: Beginner or DAQ. 40 years of development, hw and tech experience.

  Tip: USB-6501 (DIO 24ch).

  Tools: Visual Studio 2010, .net 4.0, VB.Net

  Task: Create IO industrial application to read/set e/s digital.

  Observed: The USB-6501 newly installed device is listed in MAX, but do not appear when you use 'FindResources' from the VB code, as shown below.

  Issues related to the:

  (a) what is the minimum necessary need NO software/driver read/set IO simple via USB-6501 to a VB.Net + Visual Studio application?

  (b) is shown below sensitive approach / how should I start?

  (c) if sensitive, why the device is not as a resource?

  Thank you!

  Kay Seljeseth

  

  NOR-DAQmx

• Windows XP "Apple Mobile Device Driver not installed not" device need driver mobile HELP running XP service pack 3 using an iphone 4

  Problems with the iphone 4 who it says in itunes that "Apple Mobile Device Driver not found" and nothing happens when it is connected to the USB port on charge even not. Running Windows XP 32-bit with Service Pack 3. but think I deleted all the drivers mobile when I uninstalled my Blackberry and removed the current mobile device drivers. Apple went through just fine and everything is OK it is a problem of PC and XP. Microsoft help put me on this site because need to know how to solve this problem I hope that somewhere there are mobile device drivers that work with the iphone? Site Internet de Microsft has 5 mobile device for Windows 7 drivers, but not for XP. Need help!

  Apple went through just fine and everything is OK it is a problem of PC and XP.

  Evasive classic.  It's always the problem of the other guy.

  And the classic response of some evil-educated person "technical support":

  Microsoft help put me on this site

  If the error message says 'Mobile Apple Device not found Driver' then it's an Apple problem, pure and simple.  The device driver mobile for the iPhone comes from Apple, not Microsoft.

  Do you remember what you were doing when you "deleted all the drivers mobile when I uninstalled my Blackberry and removed the current mobile device drivers?"

  Probably not... and you have not explained what has been included in "Apple went through everything."  It is time to start over by removing everything related to Apple and then put it back correctly.

  First, however, the fact that the iPhone does not load even when connected to a USB port is a bit worrying.  Works in everything else in this USB port (for example, a USB flash drive)?

  Have you tried all the USB ports on your computer?  Take a look in the Device Manager (start > run > devmgmt.msc > OK) and see if there are any icons showing warning.  If so, double-click on the entry and information "device status".

  Take a look at the event viewer (start > run > eventvwr > OK).  There is no need to go far.  Connect your iPhone, then look at the newspapers (System and Application) for since a few minutes see if there are any errors or warnings.  If so, double-click on it to get the event properties window, and then click the "Copy" icon (just below of the)

  Have you tried to recharge the iPhone using the adapter connected to Apple's USB cable?  Does it work?

  Have you tried to connect the iPhone to another computer?  With what results?

  Assuming that the hardware (iPhone, USB cable, and USB ports on your computer) is not working properly, see the following topics.

  To perform a "clean" iTunes installation uses this technique proposed, from Support of Apple HT1926 article.

  Warning: uninstall utility for cleaning Windows mentioned in the instructions below has been removed from Microsoft download servers because sometimes it seems more removed he was supposed to (I think that this phenomenon was linked to the bureau uninstalls).  You can still get utility Windows Installer Cleanup--> http://majorgeeks.com/Windows_Installer_CleanUp_Utility_d4459.html here is a free alternative Revo Uninstaller. Before using these cleaning products, you must create a restore point from the system first (or back up the registry with C:\WINDOWS\ERUNT).  See http://windowsxp.mvps.org/registry.htm a complete disk image would be safer if you have this ability.

  Go to control panel > Add/Remove programs
  Remove these applications:
  1 Apple Software Update
  2. Apple Mobile Device Support
  3 Hello
  4 iPod for Windows (this may or may not exist, be it, it is not necessary, then we can remove it)
  5 iTunes
  6 QuickTime

  Open my computer > C: > Program Files
  Delete this files (if present)
  1 iPod
  2 iTunes
  3 QuickTime

  Empty your temp directory:
  Open my computer > C: > Documents & Settings > username > Local Settings and delete the contents of the folder called "Temp".

  If you don't see the local settings, enable hidden files:
  Tools > Folder Options > view tab
  Select Show Hidden Files & folder, and then click OK

  Once this file is empty, restart the computer

  Download & install the Windows Installer Cleanup utility: [see note above regarding cleanup utility]
  http://support.Microsoft.com/kb/290301/
  Launch the utility: start > programs > Windows Installer Clean Up
  Select one of the applications mentioned above and click on remove

  Restart the computer
  Download & reinstall iTunes from here: http://www.apple.com/itunes/download/

• New installation on windows 7 pro 64-bit sees not connected wired Officejet 6500 E710a-f

  Hello!

  New installation of Windows 7 Pro 64 bit on a gigahertz 3.40 AMD Phenom II X 4 965 with 8 GB of ram. Printer drivers worked on the same bench while he was running as Windows 7 Pro 32-bit.
  After only install FF, AVG, and Acrobat (almost a clean install), downloaded the software HP Officejet full feature and pilot 2012-10-22, Version: 116,98, 28.8 M - OJ6500_E710n - z_1315.exe and tried to install the Officejet 6500 E710a f.

  The printer has a manually set static IP and can be ping from the host. Clean Windows Firewall is disabled and stopped.

  The web interface using the IP address of the printer comes with all the features works on FF.
  Network status shows connected with IP address, hostname and Mac.

  However, when installing the network audit is no ethernet connection. Even manually enter his public static IP address or hostname does not solve the problem.

  Try the USB, the same question option. I see in Device Manager under other devices HPOfficejet 6500 and 6500 HPOfficejet - Fax with a blue questionmark.
  (In the same "other devices" there are 2 Officejet 6500 with a yellow exclamation point - probably from failed network installation).

  In the printers and devices window, the 6500 is displayed with the correct thumbnail, but with a yellow exclamation point icon. Law and by selecting the convenience store, Windows comes up with the message that no driver is installed and offers a solution.  The correction ends with the error that no drivers not found for the FAX. Re-apply the patch never finds the driver.

  Anyone who has met something similar (and a solution)?

  Thanks for any help!

  Jack

  After trying to do an install clean-install of 100% and once again, the driver software could not find the printer name or IP address.
  Back at each stage, I noticed that I was not using the correct driver! For some reason I D/L the pilot E710n which is for HP Officejet 6500 a Plus e-All-in-One.
  Whatever the difference, when installing the E710n for the model does not detect the printer, or via USB or Ethernet.
  After you download the right driver for the E710a - f HP Officejet 6500 a e-All-in-One Printer (OJ6500_E710a - f_1315.exe) installation perfectly finished in a few minutes and everything goes well...

  You would think, base or USB connectivity network should not be dependent on the specific differences sub-model. I was expecting that a bad driver interrogate the device after finding its IP address and display an error message with useful text.

• 3000wireless Linksys AE adapter sees not network

  I have a Dell Dimension 8200 under XP SP3. I'm trying to set up a wireless network. I had a Linksys technical support configure AE3000 wireless adapter and it says he works correctly in Device Manager. The blue light is on the adapter and it flashes every 9 seconds. There is no no yellow exclamation point more. However, the adapter does not connect.

  Cablevision is my ISP. They sent me a smart router Sagemcom and I think I put in place correctly. However, when I remove the ethernet cable from the computer, the wireless network cannot be found and I lose my Internet connection. When I go to control panel > network connections and Lan & Internet high speed and local 3, my Linksys adapter network connection appears as not connected.

  I called Lynksys support because I couldn't get the adapter to work with the CD and the technician was able to load the drivers on their site to operate and it took about an hour. So, at this point, the adapter turned work correctly in Device Manager, but I can't connect to the Internet.

  The Cablevision tech support guy said that he thought that the problem was that the adapter has been configured before a network was in place so he can see, somehow I have to configure the card to see my network. I don't know how to do this, so I was hoping someone could advise me.

  What is sad, is that I had to call the customer service to the wireless card and they charged me just take over my computer to install the drivers because they wouldn't install from the CD or the Linksys site. Any time that Cablevision takes my system in order to solve the problem, it's free. All I wanted was for the AE3000 to work for the first time. It took the technician an hour getting the drivers from Linksys, their installation site and she tried to sell me all kinds of services for this computer Windows XP when XP gets no support after April - 4 months from now and a service to clean malware for half the price of a new computer when I already have antivirus software and use Ccleaner.

  After all this, the wireless network still does not work. I was on the phone with my ISP that passed all saying that the adapter gets a bad signal and that everything is properly connected. In fact, it worked after the deactivation and activation of the adapter, but only for a short period and technology at Cablevision saw that I had very little connectivity on the map after the reset of the smart router, which seems to work well. My suspicion is that this Linksys device is defective. It has been and that became evident when my ISP tech since the adapter has a very low 1 bar of signal. I went out and bought a wireless Netgear, instantly installed adapter and the network works fine now.

• WUSB54GS sees not all networks.

  I just installed the software for this card under Windows XP and he does not see the network (on a Belkin G Plus MIMO Router). He sees any of all networks. I tried the manual installation, but it gives me a message "cannot associate the Access Point.

  The adapter is plugged in and the Green led lights.

  I'm not sure how to proceed with this problem. Any advice or suggestions would be appreciated!

  It was a problem of auto-affectation DHCP. Still not using the Linksys software, but fixed now.

• HP Photosmart program does not "device installation is not complete.

  I have HP Photosmart Essential on my Windows 7 computer. All of a sudden it can't load it.  It says device is not complete, and sometimes this system has no minimum requirements. I can't download the program because of the minimum requirements. Any ideas. Thank you

  You can try a number of things:

  You can also try to run the program in compatibility mode

  You can find more information on compatibility modes in the articles below:

  http://Windows.Microsoft.com/en-us/Windows7/what-is-program-compatibility

  http://Windows.Microsoft.com/en-us/Windows7/make-older-programs-run-in-this-version-of-Windows

  http://Windows.Microsoft.com/en-us/Windows7/Program-Compatibility-Assistant-frequently-asked-question

  You can try to copy the contents of the installation files if its on a drive on your hard disk in a folder and browse the folder, right-click on the configuration file, and then click Run as administrator.

  Use another program like Windows Photo Gallery.

  Download Windows Essentials 2012 (Offline Installer)

• application runs on the ripple, but not device

  Hi - This is a newbie question.  I try using ripple of stable development and then compile the application for execution on a smartphone.

  There seems to be 2 different ways to use ripple.  It is like an extension of Chrome, described on this page:

  http://supportforums.BlackBerry.com/T5/Web-and-WebWorks-development/how-to-use-ripple-instead-of-the...

  A second way he starts as an application independent, described on this page:

  https://bdsc.webapps.BlackBerry.com/HTML5/documentation/ww_getting_started/getting_started_with_ripp...

  The second mode automates much of the process of packaging app, as described here:

  https://bdsc.webapps.BlackBerry.com/HTML5/documentation/ww_getting_started/creating_an_app_1885567_1...

  These seem to be the 2 different operating modes, but I've not found any discussion about the difference.  Am I missing something?  The two modes will be running test applications - for example, Hello world and the sample application UIExamples.

  Only the second mode has settings options on the key icon which automates application packaging.  Maybe I don't have something set up properly in Chrome for it get there?

  When it runs as a standalone application, it is very slow and many attribute tags are not displayed correctly, which makes me wonder if it's supposed to work in the corresponding mode, or if something is not installed correctly.

  In standalone mode it signals that he successfully built both the Hello World application and the UIExample app, and the JavaLoader said he manages to load on my Torch 9800.  Icons appear on the torch, but applications do anything when I tap on the icons.

  Thanks a lot for any clarification on how to properly install and use ripple.

  Keith Levi

  You don't need to change your paths relative to use local: / / /..., you just use the local: / / / path if you load a page from a remote domain, and you want this remote to access local domain packed files.

  All my applications use relative paths.

  Did you sign your application before attempting to run it on the device?  By looking at the output that you have validated the bbwp it shows that you not sign the application... If the application is not signed, it will not work on a real device.

  Ripple Chrome plugin is still available, as we work through some of the other features of the Beta 1 update which will be released at the end of this month.  The plug-in in Chrome is gradually and will set up a plan to end of life.

• Charger for blackBerry Smartphones Application detects not device

  Hello, I have a Blackberry Torch 9810 and when I connect it to my Windows 7 laptop. device is detected by the computer, and I am able to access all my files, & add/remove files as I want. However, when I use Blackberry Desktop manager or BBSAK, or run the Application Loader. the three programs cannot detect the device. When you use the Application Loader, where it should say "COM1" or "USB - PIN: UNKNOWN", it's white, & you can't select anything. I'm trying to do two things. Number one: back up my data device & apps; and number two: reload the new OS on the device. -Have you already uninstalled/re-installed Blackberry Destop Manager 7.1 - have installed the USB drivers & modem-(ordinateur n'a aucun problème de détection de périphérique, & me pour accéder àles données de l'appareil) - have already uninstalled/re-installed device Blackberry-device manager is BB Torch 9810; Software is 7.1 Bundle 1997 (v7.1.0.694, platform 5.1.0.507) any suggestions would be appreciated... Thank you!!

  Hello and welcome to the community!

  My apologies for the delay... this site is not a site to paid support, but rather a community of volunteer users who also have their lives to live. Sometimes, things get through... we don't intend to be the case, but sometimes it happens. Apologies that this happened to you.

  I suggest this thread:

  • http://supportforums.BlackBerry.com/T5/desktop-software-for-PC/cleanly-quot-starting-over-quot-with-...

  It begins with a process to start properly, and there is an exchange of views. Note that this is not, by any means, guaranteed to work... but it worked to much to solve the problems they have. You could add to it the use of Revo or another tool to remove own software... There are cases where things are left behind, and if they are corrupt, they can prevent the resettlement work correctly. The goal is to completely, remove from your PC, everything that is in no way, shape, or form associated with BB (registry entries, ignored of records, etc.).

  Good luck!

• BlackBerry smartphone App appears in the category on the web, but not device?

  My app play book 4 PlayBook appears in the right category, other sports, the web site version of App World, but it does not appear in this category on App World the device.  Why?  On the device, it appears via research.

  I know for sure the correct category was put into product management and the unit was targeted for liberation.

  Obviously, it is a major problem, but I get the App World Support zero answer after a few weeks to complain perhaps thought that the community can help

  Thank you

  Do

  I can now see your app in my AppWorld in the ' sport > others ' category.

• Music app sees not added manually to the music library music

  The music app Xbox is not music I manually add to the music library on my Surface. It works as expected on my desktop Windows 8, but on the RT, it doesn't. This means that the only way to get music on the device via the Xbox/service music store, which is unacceptable.

  You can try this: go to the control panel (via desktop computer) and open indexing options. Tap advanced. Type on rebuild. According to the number of files you have, you may need to wait a while, but the window will eventually display full indexation.

  Then, open the music application and see if your song had appeared.