PE830 + problems DRAC 4/p

Similar Questions

• DRAC 4 - problem with password reset

  Hello

  My company bought used/refurbished Dell R200 server with DRAC 4/p card. Now, I'm trying configure/reset password for DRAC 4 (v1.75 A01 fw) to the server. Server running Win 2008 x 64 std.

  As a first step, that the seller forgot to put with ribbon cable card, so I had to do it myself after I got it... Back to story :) at the start, I have configured DRAC (Ctrl + D; set IP DNS & - I do not see 'reset password' option), I also configured BMC to tunnel IP too (I think that's not important).

  Then, after I got windows running nicely (WU, net. FW + soft base; I did while waiting for flat cable). Once I got the cable, I have configured the DRAC at boot time, and then I went to interface http and received the error of connection (for root and calvin). In the meantime, I had to grasp because victory could not find drivers for dell DRAC: (.)

  So I installed OMSA ManagedNode x 64 (v7.4.0.2) tools RDCA (Setup did not find my card too...). Now the server startup time tripled :/ (don't know what did OMSA / or make at startup...), but nice after starting web server interface OMSA works, I can see the status of the HDD, the sensors, the tensions - almost what I need, but nothing on the DRAC (BMC only).

  Started administrator cmd and typed:

  C:\Windows\System32>racadm racresetcfg
  ERROR: Cannot perform the requested operation

  And:
  C:\Windows\System32>racadm getsysinfo
  ERROR: Cannot perform the requested operation

  So now, I think that something is not ok, but what? DRAC is broken (said kindly) or soft cannot talk to the card...

  Can anyone provide some tips?

  Hello

  I did an extra test (before leaving the workstation) and OMSA CentOS Live image downloaded and tried running the racadm - same result then the card should be broken.

  Seller has decided to replace the card because "a very likely card is broken." So now I wait for the new card.

  If I remember, I'll post summary :)

  -Summary-

  I got more than 2 cards of seller. None of them worked, firmware update found card, updated at the latest but racadm wouldn't work: (.)

  I'm packing cards back to give their feedback to the seller, but I decided to check once more... If I put each a card server and I tried the OMSA Live CentOS run racadm getsysinfo [/ i].
  I don't know if I would be really happy but one of the DRACs replied :), so without hesitation, I run "racadm racresetcfg" and I had no errors (happy), so I waited a moment for card to reset, and then rerun the getsysinfo but there not as before, but now I can log in the web and I changed my password.

  I suspect editing card, but the PREV raid card works very well, there could be something offshore with this putting on drac PCI slot. Seller also admitted that he had specially the elevators in order to install the drac4 card.

  I consider this as solved :)

  PS. Sorry for my bad English.

• DRAC problem

  DRAC does not respond within Dell open manage how to restart the agent can someone help me

  1. open putty

  2. connect to the Drac (admin user)

  3. tap $ racadm racreset

  4. the drac will reset

  5. it will connect to Dell management

• iDRAC on Dell R610 problem

  Hello

  I just got a new Dell R610 and I tried to configure the iDRAC on her card. I have it configured on interfaces of multiple T300 Dell and the ILO on the different models of HP servers successfully. But for some reason, I'm going to have serious problems with it.

  I think he got an iDRAC Express card as there is no extra ethernet port on the server, just the standard 4 integrated NETWORK interface the iDRAC BIOS are version 1.70 I understand is the last.

  In the screen configuration (Ctrl + E) iDRAC, iDRAC and IPMI over LAN are enabled. Selection of NIC is set to shared so for active LOM, it reports 'No. Active LOM'. VLANs are disabled, iDRAC Express stand them? -Once it works I would like to enable it if possible.

  Only NIC1 (eth0) is connected to the switch. I tried configuring it with DHCP, but he never does an address even if the operating system gets a.

  To remove the switch / VLAN even tried to connect NIC1 directly on an other server tcpdump and running with iDRAC configured with a static IP (the default value of 192.168.0.120). Did not get a thing of it. I could see the arp requests going out but not responses to iDRAC.

  So, how do you get the iDRAC to work?

  Thank you.

  Today technician Dell replaced our motherboard and this fixed a problem with the DRAC.

  New motherboard uses older versions of BIOS and DRAC BIOS main:

  principal: was 3.0.0, now for 2.0.11
  DRAC: was 1.70.21, now 1.41.13

  DRAC works now, and, Yes, she has the web interface.

  PS unfortunately, but this will not be fixed another issue we have with H200 controller or it's linux driver mpt2sas: https://bugs.launchpad.net/linux/+bug/777441 (ClxAdmin, if you use Linux on that server, what distribution of linux/version you are using?)

• PowerEdge T610 Server; problema a tutte wears USB [CF]

  Salvo.

  Without apparent reason, all the door del USB Server hanno di funzionare then, despite it operating system (ESXi) riconosca I ordered UHCI and EHCI.

  1. Al boot it sistema no ad alcuna tastiera connessa, international one nice keyboard by poi boot failure place.
  2. non e possibile access al BIOS;
  3. He DRAC no notes some problema specifico.
  4. all the door sound place alimentate con misurando it Tester e di output 5v;
  5. tutte altre funzioni della macchina pleased no compromesse.

  Senza USB sono compromesse all the functional interaction with the macchina di, nonché altri servizi correlati (gestione energia, archiviazione ecc.).

  Should be possible at least al BIOS in some modo, o estrarre maggiori information access. Resto in attesa di una procedure.

  SERIAL NUMBER: GTFX05J

  Grazie.

  --

  Luca Lenardi
  0434 550882
  ATRA Srl

  By staff? Some suggestions?

• OME v2.0 - ws - man to DRAC, General questions

  Hello

  I'm currently testing a number of things within my organization for OME. We have installed v2.0. I managed to use SNMP to enter a few servers for MOE, displaying information on material etc. However I cant seem to get DRAC using ws - man. Are there recommended references to use?

  On the DRAC and servers, if the hostname of a server is specified within the drac will create 2 entries separate devices? (one for the server, one for the drac) or it will merge the two?

  Thank you

  Hi and thanks for the post.

  If you have 12G or 13 G Dell servers, it is probably easier to simply discover the IP address of the iDRAC via WSMan (disable SNMP from the wiz of disc).

  If you _do_ discover the _and_ IP address band iDRAC (via WSMan) via SNMP + OMSA, it should merge the data in an entry.  But for the sake of simplicity, it is sometimes easier to do how I mentioned above.

  Just be sure to hit all the checkboxes on the page of the wizard for the discovery of WSMan.  If you still have problems, you can try the WSMan test on the Dell troubleshooting tool.

  Kind regards

  Rob

  delltechcenter.com/OME

• DRAC 5 installation media: "Selection of CD/DVD-ROM not valid."

  I connect to a Drac 5 with firmware version 1.33 using 32 bit Firefox 2.0.0.20 as downloaded from Mozilla.org running on CentOS 5.2.

  It seems to me installing the Console and media attach the plug-ins OK, but I get a problem when I try to join a DVD-ROM. I select the ISO from Centos 5.2 image, but when I press the Connect button I get a pop-up indicating that "the page at https://192.168.108.102 says: ' then 'selection of CD/DVD-ROM not valid.'.

  If I try the same thing using IE 7 under Windows, it will connect, but since I don't have Windows in the data center is too slow and no use for me to try to connect a DVD over the WAN.

  I searched Google and found nothing documenting this error so I am a bit stuck as to what it means and what to do about it.

  I tried to run firefox as root also in case the plugin was trying to cordon the ISO file.

  I also eliminated any firewall blocking the ports.

  This problem is related to Internet Explorer 8.
  The error can be resolved by adding the IP address as a trusted site in Internet Explorer 8.

• 2970 DELL cannot ping IP DRAC [MS]

  I try to use the DRAC but able to ping the IP of the DRAC.

  I have configured as done in this video:

  www.YouTube.com/watch

  What I try to study the problem?

  Thank you

  Buongiorno,

  He firmware Bolivia e exclusively by the idrac, by running, dopo averlo copiato knew local folder, verifichi che he gives abbia I frequently precinct (esegua is chmod 777 nomefile.bin).

  Per quanto someday become general e possibile utilizzare he nostro dvd iso image Q1 Server Update Utility DVD ISO v7.2.1:

  downloads.dell.com/.../SUU_721_x32_Q12013_A01.iso

  Speaking saluti

  Manual

• Cannot find download DRAC firmware

  We have a DRAC 5 in a PowerEdge 1950 running Windows Server 2012R2. I can not get a console window that works with the DRAC 5 on my laptop Windows 8.1 with IE, Chrome or Firefox. The window is blank in Chrome and Firefox and toolbar does not work when I click on the buttons in IE, so impossible to send a ctrl-alt-delete. I thought that the DRAC firmware needs updating. It's on v1.0 (Build 06.05.12). When I go to downloads for my PE1950, it does not show any firmware downloads DRAC. The DRAC was purchased subsequently, not with the system. I searched on Google, trying to find the firmware from Dell DRAC5 downloads but can't find that apply to a PE1950 or can I get to work with her. When I try to run, I am told that they do not work with my system. I thought that the update of the firmware might get the console works best. My previous experience with consoles does not not on DRAC was that Dell had updated me the firmware. So please tell me where I can find the firmware since I'm not find it with search.

  The forum does not like FTP sites, and it has not changed the HTTP FTP.

  They are here:

  http://downloads.Dell.com/published/pages/PowerEdge-1950.html

  

  First choose the Package update for Microsoft Windows (a WN32 in the namem, labeled external on the FTP site). If you have problems, use the version of hard disk.

• Problem updating iDRAC and LC on Poweredge R710

  Hello

  I am facing problems updating one of our Poweredge R710 (all others worked like a charm). Using OME I could install almost all day, but iDRAC (Firmware 1.10--> 1.95) updates and controller of lifecycle (application 0--> 1.6.0.73) will not be successfully completed.

  OME to ESM_Firmware_CMDN0_WN32_1.95_A00 error message. EXE: "performance operation exceeded a specified time-out period. The update has not completed; You must restart your system and try again. "(even after several server restarts the message is always the same).

  Error message in OME for lifecycle - Controller_Application_GFFFC_WN32_1.6.0.73_A00. EXE: "update failed: failed to secure copy - the secure copy function has failed.

  When starting the server "Update Services system requirements" is shown in the upper right of the bootscreen. I've tried ressetting iDRAC (Ctrl + E at the start), turn off the server for 30 minutes (cable unplugged, replugged, waited 5 minutes, powered by the server) update system Build & Update Utility thorugh with SUU 7.3.1 and finally using the CentOS OM 7.3 Live DVD. None of this has worked successfully and I have no more ideas. Maybe someone has a?

  Here are the necessary links. Fires within the OS.

  DRAC - http://www.dell.com/support/drivers/us/en/19/DriverDetails/Product/poweredge-r710?driverId=63KCR&osCode=WS8R2&fileId=3287900761&languageCode=en&categoryId=ES#

  Then run this, it is a set of lifecycle controller repair. http://www.Dell.com/support/drivers/us/en/19/DriverDetails/product/PowerEdge-R710?driverId=8F07J&osCode=WS8R2&FILEID=2731110409&LanguageCode=en&CategoryID=SV

  Then update the LC with this - http://www.dell.com/support/drivers/us/en/19/DriverDetails/Product/poweredge-r710?driverId=F0D50&osCode=WS8R2&fileId=2984894513&languageCode=en&categoryId=SV#

• Unusual problem with PE2950III with 2 x Xeon 5450, 64 GB RAM, PERC 6i

  I have a PE 2950III located in a data center that has a particular problem.  Know that it runs in a configuration "unsupported", then bets are open regarding the "typical" questions  It runs Windows Server Datacenter with Hyper-V 2013 and some children VMs.  The only role on the host is the Hyper-V role and virtual machines are all Windows Server 2016.  There are storage set up on the server, and all 6 discs are configured RAID 0, which should be the same as with all discs as the discs.  Storage spaces work fine.  The strange thing is that the server seems to restart spontaneously, and * only on the weekends.* when I use the DRAC to access the server, the PERC6i shows a virtual disk is missing.  This isn't really a problem since the redundancy of drives are supported by storage.  It is a storage repository, so performance is not at the top of the list for the server.  When they restart of the server, he says that PERC 6i is missing virtual disk 0, which is the boot/OS disc, so the server will not start.  It does not show installed foreign disks to be.

  Once the server power pedaled, PERC 6i said that a foreign disk was detected and press 'F' to add it to the configuration.  The 'F' is activated, it starts normally, the departure of VMs, and all goes well.  Anyone happen to know what could cause the server only on Saturday or Sunday, when he is in charge less on it.  It is attached to the PERC BIOS screen.  Until the server is power rolled, it does not show the foreign drives present.

  The part not supported - all disks are not certified Dell, and three drives 3 TB disks, which PERC 6i reads like 2 TB.  It seems to work very well in this configuration and does not complain on the disks not Dell used on the server.  I would like to know what event may occur to cause a crash and restart the server, the driver PERC for the 6i report a predictive failure disk 0:0:0, which I replace.

  I have now, I venture in unexplored territory and not territory in charge.  I'm just hoping it will limp along until 1 January 2017 server seems to be close gracefully based in the event log, as all services are trying to stop before the closing happen, but after it stops, the RAID controller stop re-boot process, not recognize disk 0:0:0.  The event log is not unsupported drives are installed, but not during startup.  I know it is relevant that I get off of this configuration does not support as soon as POSSIBLE, and who has been most understood.  Fortunately, this server is for backups of backups and not to LOB or important servers.

  The firmware is updated.  Would it be possible that 3 TB drives cause a questions (I personally don't see how they thought) or is it a disc while they were patrolling operation that happens over the weekend him crashes?

  If anything could throw any ideas on the ring I would certainly appreciate it.  Thank you!

  Hello.

  e320_cdi

  Storage spaces work fine.  The strange thing is that the server seems to restart spontaneously, and * only on the weekends.*

  Do you have jobs sever or applications planned for the weekend?

  e320_cdi

  The part not supported - all disks are not certified Dell, and three drives 3 TB disks, which PERC 6i reads like 2 TB.  It seems to work very well in this configuration and does not complain on the disks not Dell used on the server.  I would like to know what event may occur to cause a crash and restart the server, the driver PERC for the 6i report a predictive failure disk 0:0:0, which I replace.

  PERC 6i supports up to 2 TB of capacity HD HD any capacity you use. HDs uncertified by readers using can lead to unpredictable problems that you have observed. I suggest using Dell certified readers.

• Unable to Scan to the computer after downloading macOS Sierra. Is this a software problem?

  How can I scan from HP Envy 4500 to computer after downloading macOS Sierra?

  Hello wdemetris,

  Thanks for asking for scanning helps here in the Apple Support communities. I understand how it is important to have access to your scanner and am happy to offer help for this.

  As a precaution, we always recommend that you have backups to make sure that all your data is safe. You can perform a backup using Time Machine and an external hard drive. Use this article to help make a backup of your Mac: use Time Machine to back up or restore your Mac.

  Then, in accordance with article help: printer and scanner for Sierra, El Capitan, Yosemite, and the Mavericks macOS software, the HP Envy 4500 e-all-in-one is supported for printing and scanning. The drivers must be installed, but if not, if it please go to the App Store and check the updates tab to see if there are updates for HP. If there is, please install.

  If you have only general questions about how to get your updated scanner in place or how to scan pictures, please check out these two articles: macOS Sierra: implement a scanner & macOS Sierra: scan images or documents. If everything is configured correctly and you still have problems scanning, please visit this help article: macOS Sierra: scanning troubleshooting.

  Thanks again and have a great rest of your day.

• My iPhone 6 installed 10.0.2 stops when it gets to 40% of autonomy.  In addition, it seems to pass power WAY to fast with the new software.  Does anyone else have this problem?

  My iPhone 6 installed 10.0.2 stops when it gets to 40% of autonomy.  In addition, it seems to pass power WAY to fast with the new software.  Does anyone else have this problem?

  Hello brooksm549,
  Thank you for using communities of Apple Support.

  I got your message which, since updating your iPhone 6 to iOS 10.0.2 your iPhone stops when it is 40% and the power to empty very quickly. I understand your concern with the iPhone turn off and drains the battery. I recommend you to review the use of the battery to see what app contributes more to the battery drain. The following article will provide you with steps on how to check the use of the battery:

  On the use of the battery on your iPhone, iPad and iPod touch

  When you know about the soft uses more battery, you can change your settings in order to optimize the battery life:

  Maximize the life of the battery and battery life

  Best regards.

• MacBook Pro display problem

  Hello members of the community.

  As of recently, I have noticed some glitches when feeding on my MacBook or awakened from his sleep.

  The colors are distorted, usually with pink, green, or yellow blobs. Blobs cannot entirely replace the colors, they appear to be contained in a element would normally be. For example. the menu bar will be partially pink and white, but pink does not leave the menu bar in this area, and the Office has green lines on it.

  I tried to take a screenshot, but the problem resolves in about 20 seconds, but it's a recurring problem.

  It happens when I wake up, connection or not. I had also certain powers serious and problems of performance, such that my MagSafe LED would not illuminate when plugged on rare occasions, fan could turn unnecessarily, graphics performance were SUPER slow, and the health of my battery was running out quickly. I actually ran a report on the system at 2 different times and my quality of full load is depleting of 1.2% per charge cycle, which is very worrying. I went from 6281 mAh mAh 6138 maximum capacity after two cycles of load. I'm tracking closely it because at this rate, my battery will survive only at load cycles about 150 instead of the 1000 expected, gives me the idea that this could very well be a bad battery. The computer is also warm to the touch while you sleep, not connected to the power supply. I NAP active but even taking into account should not be hotter my iPhone did the same thing.

  I have reset the SMC, and it solved a couple of problems. The charger works fine now and my performance improved considerably (which made me feel better, either it is a high-performance laptop, a 11-inch MacBook Air should not he surpass), and battery life has improved. I feel even if it uses a lot of power in his sleep. Maybe I need to turn off the NAP and see if that makes a difference. The graphic bug still persists however, and I don't have enough time to see if the max battery is depleting again.

  In regards to the bug, is there something that can be done? Basically, I want to assure you that I took all appropriate measures or if someone else has this problem to see if it can be software related instead of my computer.

  I have the entry level MacBook Pro with the retina, last generation.

  Any constructive contribution welcome!

  See you soon.

  -adreaux

  Hello bernardn753,

  After reviewing your post, it seems that you are having problems with the screen showing strange things on it. Looks like you already have a troubleshooting. I recommend you read this article, as reset NVRAM would be to reset your screen resolution settings that should help.

  How to reset the NVRAM on your Mac.

  Thank you for using communities of Apple Support. Good day.

• with IOS 10.0.2 - 5s iphone Bluetooth problems

  Since upgrading ISO 10.0.2 my M50 from PLT Plantronics (helmet unique headset) do not reliably connects with my iPhone 5 more. I have to go to the settings, activate bluetooth turned off/turned on, touch the device on the bluetooth page, etc. Once it connects successfully, it will reconnect (if I turn off the headset and turn it back on) for a short period. The next day he does not connect itself but I play with bluetooth on the iPhone again.

  It has always worked perfectly before the 10th of IOS.

  And, as I noticed others mentioning, the volume is much lower with IOS 10. The maximum volume is much lower. I can barely hear it now, more normal background noise, while driving.

  I did:

  Forget this device for the PLT M50 and paired again (several times)

  I did a Reset Network Settings

  I don't know what else to do - but it's a 10.0.2 IOS issue.

  Hello AppleUser2k,

  Please ask questions about your problems of connection between your iPhone and your Plantronics headset since you upgraded to iOS 10. I understand how important it is to have your Bluetooth devices connect with your iPhone with reliability. Here's what I recommend.

  The first thing we want to make sure is that all your data is safe. You can perform a backup in iCloud or iTunes using this article: backing up your iPhone, iPad, and iPod touch.

  Once your data is safe, try the troubleshooting steps in this article to help: get help to connect a Bluetooth accessory with your iPhone, iPad or iPod touch device should also check with the manufacturer that the device has all the drivers and firmware to work with the new version of iOS.

  If you have checked everything and that you have installed the latest firmware or driver and always are problems, please be aware of your surroundings when you encounter these problems. If you can isolate the time or location, you see the problems, you can isolate the cause. You can even see this help article to ensure that you are not affected by outside interference: the potential sources of Wi-Fi and Bluetooth.

  Thanks again and have a great rest of your day.