Phone connected to the SPA3102 rings not until reset

Similar Questions

• My Sprint HTC Android mobile phone connects with the supplied USB cable, but the computer says 'No HTC Device Connected'

  My Sprint HTC Android mobile phone connects with the USB cable, but the computer says 'No. HTC Device Connected' so I can't sync...

  Hello

  1. do you have HTC Manager installed on the computer?

  2. have you tried it with different USB ports?

  You need the HTC Sync HTC phone Manager software.

  Method 1: Try again with different USB ports and see if that helps.

   

  Method 2: If HTC Sync is installed, if you get the message "no device connected" in HTC Sync, ensure that your phone USB setting is changed to "Charge Only" to "HTC Sync".

  If the methods above do not help, you can contact HTC for additional help.

  Here is the link: http://www.htc.com/us/support/

• Computer connects to the network, but not to the Internet, connect to the only local

  Hello world

  OK, so I have a HP computer with the installed version of Windows Vista Home Premium 32-bit. I've had it for almost 2 years now and have had no problems connecting to Internet... until now.

  I can connect to networks... both wireless and cable, but I can not get Internet. I used the IP, subnet mask, gateway and server settings DNS to another computer that works with this specific local network just to see what happens... my computer has failed.
  Until recently, I could connect to this WiFi connection in a coffee shop, but the last time I tried it didn't work. I've connected to the network but not the Internet. He told me that the DNS server did not. I'm starting to think that something is wrong with my computer.

  I saw that the solution for some people running the Norton removal tool, however I had uninstalled Norton almost as soon as I got my computer 2 years ago and ran McAfee instead. I don't think that Norton should have an impact on me more.

  Is there a solution to this problem... or I'll just have to try everything that is out there?

  Thanks for your help!

  Hi MomPlaysBass,

  Finally, my problem has been resolved - it wasn't my computer after all. The modem may only be connected to a computer. If you want to connect to another computer, you can connect the computer to the modem and then put it back. My computer worked fine after that. Whenever we want to switch between computers, even if I have to reset the modem.

  I don't think you have the same problem, but just in case, you can try to reset your modem - it's a button on the back or a small hole that you can reach with a pen... Hold the stylus for about 5 sec or maybe a bit more and then let go. That should reset your modem and might help you with your problem. Your computer should also have created a restore point... If all else fails maybe you can try to get back to the final point where your computer worked.

• A connection to the host could not be established

  I am running windows xp on an ubuntu host and it was working fine until I tried to start my desktop shortcut xp today.  I get the error message "a connection to the host could not be established."  I don't think I changed anything since the last time it worked correctly.

  Also, I can't access web page.  Firefox "unable to establish a connection."

  Someone has an idea?

  Hello

  See vmware running services. No doubt vmware - pass does not work.

  Try to start /etc/init.d/vmware-mgmt

  J.

  If you have found this device or any other answer useful please consider the use of buttons useful or Correct to award points.

• I'm trying to update the software to 9.3 on my IPad 2.  I get the message that it is impossible to check the update since I'm no longer connected to the Internet.  Not true.  I am connected.  Any suggestions?

  I'm trying to update my IPad 2 iOS 9.3 software.  It keeps telling me that it cannot be verified because I am is no longer connected to the Internet.  Not true.  I am connected.  Any suggestions?

  Many users have encountered problems to update their devices, their activation or signing into their account after updating iOS 9.3. Apple is aware of the problem and working on a fix.

  Take a look at these articles for additional information on the issue or adapt:

  If you are unable to activate your iPhone, iPad or iPod touch after installing iOS 9.3 - Apple Support

  If you are unable to activate your iPad 2 (GSM model) update to iOS 9.3If you cannot activate your iPad 2 (GSM model) updated to iOS 9.3

  Apple stop updates iOS 9.3 for older iDevices due to activation server locking problems more

• Test the connection to the database failed: connection to the server could not

  I have one of my servers HPOV NNMi 9.23 restarted this morning and NNMi is loading is no longer.  I see the following errors in the newspapers said:

  /var/opt/OV/log/NNM/public/nmsdbmgr.log

  06/04/2015-09:28:05 connection to the database test failed: connection to the server could not: connection refused
  The server running on host "127.0.0.1" and accept
  TCP/IP connections on port 5432?

  /var/opt/OV/log/NNM/public/postgres.log

  2015-04-06 09:25:55.312 EDT: 8580:0LOG: could not translate the hostname "localhost", "5432" service at the address: name or service not known not

  2015-04-06 09:25:55.312 EDT: 8580:0WARNING: could not create listen to "localhost".

  2015-04-06 09:25:55.312 EDT: 8580:0FATAL: could not create TCP/IP sockets

  I have checked/etc/hosts and found the following entry:

  #; Local
  #;
  127.0.0.1 localhost

  The command line, I can ping localhost without problem.  Not sure why NNMi begins not at this point.

  Turns out be the permissions on the file/etc/hosts.

• Account of Hotmail, when I connect to the page will not download?

  Once I connect to the page will not download?

  Hello

  Please provide all the information we need to help us help you.

  How to ask a question
  http://support.Microsoft.com/kb/555375

  -------------------------------

  Answers is a peer group supported and unfortunately has no real influence on Hotmail.

  HotMail has its own Forums, so you can ask your questions there.

  Windows Live Solution Center - HotMail - HotMail Forums Solutions
  http://windowslivehelp.com/

  Hotmail - Forums
  http://windowslivehelp.com/forums.aspx?ProductID=1

  Hotmail - Solutions
  http://windowslivehelp.com/solutions.aspx?ProductID=1

  How to contact Windows Live Hotmail Support
  http://email.about.com/od/hotmailtips/Qt/et_hotmail_supp.htm

  Windows Live Hotmail Top issues and Support information
  http://support.Microsoft.com/kb/316659/en-us

  Compromised account - access unauthorized account - how to recover your account
  http://windowslivehelp.com/solution.aspx?SolutionID=6ea0c7b3-1473-4176-b03f-145b951dcb41

  Hotmail hacked? Take these steps
  http://blogs.msdn.com/b/securitytipstalk/archive/2010/07/07/Hotmail-hacked-take-these-steps.aspx

  I hope this helps.

• My works wireless, but my connection to the LAN does not work?

  I have a Toshiba L305-S5917 laptop and my connection to the LAN does not at all, when I plug my CAT 5 cable into the slot not strikes is the lights. IM able to use my wireless works fine. All this happened when my laptop crashed due to a virus. I reloaded all windows from XP to Windows 7 and also bought Numbus disk driver and recovery for my model laptop and still no connection to the LAN... pls help.

  Hello

  Sorry I'm not quite clear about the situation.

  You posted on the Vista Forum; you have loaded Win XP and you running Windows 7?

  If the computer is currently running on Windows 7, newspaper to the support site for Toshiba laptop, download Windows 7 drivers for the wireless network card and install them.

  In general.

  Check the Device Manager for the entry of valid card of the wire.

  http://www.ezlan.NET/Win7/net_dm.jpg

  If there is no valid entry, remove any entry from fake and re - install the drivers for the wireless card.

  ----------------------------------

  Try installing the latest drivers from the card manufacturer support page.

  Download the drivers and extract them to a folder of your choice.

  In Device Manager, right-click on the adapter.

  Click Update drivers and choose her browse my computer for drivers.

  Choose let me a list of choices, click on disk and point to the folder with the drivers.
  -------------------------------------

  Check network connections to make sure that you have a Local Area Connection icon/entry, and that the properties of the icon (right-click on the icon) are correctly configured with the TCP/IPv4 protocol in the properties of network connections.

  http://www.ezlan.NET/Win7/net_connection_tcp.jpg

  Connect you to the menu of the router from a work computer and make sure DHCP is on, and it is configured to assign IPs which can cover the number of computers that are connected (a bit more will be even better).

  Turn off the computer and the router, reset the router and the computer.

  Right-click on the wireless network connection card, select status, details and see if she got an IP address and the rest of the settings.

  On the State of intellectual property.

  TCP/IP and its variables usually look like this.

  Right-click on the wireless network connection card, select status, details and see if she got an IP address and the rest of the settings.

  Typical TCP/IP status looks like this.

  http://www.ezlan.NET/Win7/status-NIC.jpg

  Description is the data of the card making.
  
  Physical address is the MAC of the card number.

  The xx must be a number between 0 and 255 (all xx even number).

  YY should be between 0 and 255

  ZZ should be between 0 and 255 (zz all the same number.)

  The date of the lease must be valid at the present time.
  
  * Note 1. IP that starts with 169.xxx.xxx.xxx isn't valid functional IP.

  * Note 2 There could be an IPv6 entries too. However, they are not functional for Internet or LAN traffic. They are necessary for Win 7 homegroup special configuration.

  ------------------------

  Also, make sure that the software firewall on each computer allows free local traffic. If you use 3rd party Firewall on, Vista/XP Firewall Native should be disabled, and the active firewall has adjusted to your network numbers IP on what is sometimes called the Zone of confidence (see part 3 firewall instructions

  General example, http://www.ezlan.net/faq.html#trusted

  Please note that some 3rd party software firewall continue to block aspects of the Local traffic even it they are off (off) . If possible, configure the firewall correctly or completely uninstall to allow a clean flow of local network traffic. If the 3rd party software is uninstalled, or disables, make sure Windows native firewall is active .

  Jack - Microsoft MVP, Windows networking. WWW.EZLAN.NET

• WRTG54S to connect to the network, but not internet

  I have a WRTG54S and Mediacom 12mbps. My router worked fine on my old laptop (a Dell Vista), he was sitting in a box for about 6 months and now that I have a new (Sony running 7) I can connect to my network, but not internet. I have updated the firmware of 7.6 to 7.8 without change. I have tried no security, wep and wap without change. Also, I cloned the MAC, once again no change. Windows cannot detect all problems, and when I try to activate the router to connect to the internet it always says connection failed. I can connect directly connected to the modem but not when connected to the router or wireless. Any ideas? Thank you

  Problem solved. I had to go to a Motorola SurfBoard 4100 to a 5100. Thanks anyway

• Connection to the local network not appearing is not in the area of notification on the Windows 7 computer.

  Connection to the local network not appearing is not in the area of notification on the Windows 7 computer.

  Right-click on the taskbar and select Properties, and then click Customize.  Look for the connection and modify to display the icon and notifications.

• What is the proper way to create a user who can connect through the Console, but not through the VMWare Client?

  I did the following steps:

  1. create a user

  2. assign the Group root (remove all the other group of the user)

  What's my not just?

  Thank you!

  It is the way to do it.   Either you must be part of the root group to be given to the role admin (or a bespoke) at the level of the host to access the DCUI.

  If you create a user is added to the root group, but is assigned all permissions (either singularly or through a group) on the host then, then the user will be able to connect to the DCUI but not the client vSphere (or any other method of the API).

• connection to the server is not available error when downloading the journel

  Dear experts,
  
  When downloading the journels to R12 using ADI we face below error
  "connection to the server is not available, please contact your technical support representative.
  
  our environment is apps: 12.0.6 and database 10.1.0.5, linux redhat 5
  
  Please suggest on this issue, there is no error in appl_top/bne/12.0.0/log (infact nothing in this directory)
  
  
  Concerning
  Francis K.
  
  Published by: 918055 on July 3, 2012 06:54

  918055 wrote:
  Hello Hussain,

  Problem has been solved, raised the issue because of the Excel settings, we enabled the option "enabled all macros" and then it worked fine.
  Thanks for your advice on this matter

  Kind regards
  Francis K.

  Thanks for the update and for sharing the solution!

  Hussein

• See connection to the server does not see any source

  Hello

  I have a very big problem, my opinion-connection to the server does not see any computer desk-source. I had seen some sources but not all a few hours ago. At this point, I did not see the sources I so did many trys to see this source. Overall I don't have luck, and now I see no source.

  The problems started with a VM Windows Server 2003 EE SP2, I need training to be deployed with a view. I have not seen this virtual machine, either I chosse linked clones or not.

  The journal of the events of this virtual machine show, auto login TP Server service not started right.

  I hope to have some ideas that will help me to solve this problem.

  Greetings

  You can use a server OS in a pool of Terminal Server services.  If you want to set up a desktop computer, you will need to use a desktop supported OS.   You can find operating systems supported in the Administrator's guide, http://www.vmware.com/pdf/view31_manual.pdf.

  If you have found this device or any other useful post please consider the use of buttons useful/correct to award points

• ORA-02019: description of the connection to the remote database not found

  Hi all
  
  10.2.0.4 on solaris 10.
  
  I can tnsping and connect to a tnsentry in tnsnames.ora from the server, but when I use the same in dblink, get the error below:
  ORA-02019: description of the connection to the remote database not found. Here's the scenario. any idea?
  

  medt01:medtora:/medt/oracle/product/102/network/admin$ tnsping medcon
  
  TNS Ping Utility for Solaris: Version 10.2.0.4.0 - Production on 09-NOV-2011 23:49:23
  
  Copyright (c) 1997,  2007, Oracle.  All rights reserved.
  
  Used parameter files:
  /medt/oracle/product/102/network/admin/sqlnet.ora
  
  
  Used TNSNAMES adapter to resolve the alias
  Attempting to contact (DESCRIPTION = (ADDRESS_LIST = (ADDRESS = (PROTOCOL = TCP)(HOST = 192.168.0.102)(PORT = 1523))) (CONNECT_DATA = (SERVICE_NAME = medcon)))
  OK (20 msec)
  medt01:medtora:/medt/oracle/product/102/network/admin$ sqlplus medts_ed/medfcv@medcon
  
  SQL*Plus: Release 10.2.0.4.0 - Production on Wed Nov 9 23:49:31 2011
  
  Copyright (c) 1982, 2007, Oracle.  All Rights Reserved.
  
  
  Connected to:
  Oracle Database 10g Enterprise Edition Release 10.2.0.4.0 - 64bit Production
  With the Partitioning, OLAP, Data Mining and Real Application Testing options
  
  SQL> Disconnected from Oracle Database 10g Enterprise Edition Release 10.2.0.4.0 - 64bit Production
  With the Partitioning, OLAP, Data Mining and Real Application Testing options
  medt01:medtora:/medt/oracle/product/102/network/admin$ sqlplus medts_ed/medfcv@medcon
  
  SQL*Plus: Release 10.2.0.4.0 - Production on Wed Nov 9 23:59:54 2011
  
  Copyright (c) 1982, 2007, Oracle.  All Rights Reserved.
  
  
  Connected to:
  Oracle Database 10g Enterprise Edition Release 10.2.0.4.0 - 64bit Production
  With the Partitioning, OLAP, Data Mining and Real Application Testing options
  
  SQL> exit
  Disconnected from Oracle Database 10g Enterprise Edition Release 10.2.0.4.0 - 64bit Production
  With the Partitioning, OLAP, Data Mining and Real Application Testing options
  medt01:medtora:/medt/oracle/product/102/network/admin$ tnsping medcon
  
  TNS Ping Utility for Solaris: Version 10.2.0.4.0 - Production on 10-NOV-2011 00:00:02
  
  Copyright (c) 1997,  2007, Oracle.  All rights reserved.
  
  Used parameter files:
  /medt/oracle/product/102/network/admin/sqlnet.ora
  
  
  Used TNSNAMES adapter to resolve the alias
  Attempting to contact (DESCRIPTION = (ADDRESS_LIST = (ADDRESS = (PROTOCOL = TCP)(HOST = 192.168.0.102)(PORT = 1523))) (CONNECT_DATA = (SERVICE_NAME = medcon)))
  OK (0 msec)
  medt01:medtora:/medt/oracle/product/102/network/admin$ sqlplus medts_ed/medfcv@medcon
  
  SQL*Plus: Release 10.2.0.4.0 - Production on Thu Nov 10 00:00:07 2011
  
  Copyright (c) 1982, 2007, Oracle.  All Rights Reserved.
  
  
  Connected to:
  Oracle Database 10g Enterprise Edition Release 10.2.0.4.0 - 64bit Production
  With the Partitioning, OLAP, Data Mining and Real Application Testing options
  
  SQL> exit
  Disconnected from Oracle Database 10g Enterprise Edition Release 10.2.0.4.0 - 64bit Production
  With the Partitioning, OLAP, Data Mining and Real Application Testing options
  medt01:medtora:/medt/oracle/product/102/network/admin$ sqlplus medc_pl/medxcdsw3
  
  SQL*Plus: Release 10.2.0.4.0 - Production on Thu Nov 10 00:00:17 2011
  
  Copyright (c) 1982, 2007, Oracle.  All Rights Reserved.
  
  
  Connected to:
  Oracle Database 10g Enterprise Edition Release 10.2.0.4.0 - 64bit Production
  With the Partitioning, Real Application Clusters, OLAP, Data Mining
  and Real Application Testing options
  
  SQL> create database link med2con connect to medts_ed identified by medfcv using  'medcon' ;
  
  Database link created.
  
  SQL> select * from medc@med2con;
  select * from medc@med2con
                              *
  ERROR at line 1:
  ORA-02019: connection description for remote database not found

  Try this,

  SQL > create database link med2con connect to medts_ed identified by using medfcv ' (DESCRIPTION = (ADDRESS_LIST = (ADDRESS = (PROTOCOL = TCP) (HOST = 192.168.0.102)(PORT = 1523))) (CONNECT_DATA = (SERVICE_NAME = medcon)))';

  SQL > select * from medc@med2con;

• connected to the database target (not started)

  Hi Experts;
  
  I work with Oracle 10 G DB, and I try to run a backup using RMAN. The DB is not using the archive.
  
  When I invoke the RMAN, to start the procces when I type connect target, I got this message: connected to the database target (not started). Previous to call RMAN I executed the command export ORACLE_SID = SIDDB.
  
  After this, I restarted the DB, but I continue to have the same problem.
  
  Any suggestions of what to do or change, to solve this problem?
  
  Concerning
  
  Al

  Hi user,

  Check the alert.log to all critical errors, if there are and try to start the database to mount using sqlplus and then run your guest RMAN backup script.

  Please share the steps that you performed earlier.