Photoshop elements 8.0 does not start after a windows update 10

Similar Questions

• computer does not start after the Windows XP logo window

  Windows xp home edition
  service pack 2
  Dell inspiron 1501

  1. computer does not start after the Windows XP logo window
  2 works well in safe mode, even connect to the external monitor
  3. I reinstalled xp many times, problem stil exist.

  All the answers?

  Hi dhanushm,

  1. What happens after the Windows logo screen?
  2. You receive an error message?
  3. You have security software installed on the computer?
  4. Have you performed an installation clean Windows XP and even after that this problem exists?

  Method 1

  As the computer starts up fine in safe mode there is a possibility that some third-party programs installed on the computer is the origin of the problem.

  I suggest that you configure the computer in a clean boot state and check if it helps.

  To help resolve the error and other messages, you can start Windows XP by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

  See section to learn more about how to clean boot.

  How to configure Windows XP to start in a "clean boot" State

  http://support.Microsoft.com/kb/310353

  Reset the computer to start as usual

  When you are finished troubleshooting, follow these steps to reset the computer to start as usual:

  1. Click Start , and then click run.
  2. Type msconfig , and then click OK.
     The System Configuration utility dialog box appears.
  3. Click the general tab, click Normal Startup - load all device drivers and services , and then click OK.
  4. When you are prompted, click restart to restart the computer.

  Method 2

  If fails it above step can refer to the article below and try the steps mentioned, check if it helps.

  After the Windows Logo appears or after you log in to Windows, a Windows XP computer cannot display the wallpaper, a black screen or a blue screen

  http://support.Microsoft.com/kb/318027

• Lightroom cc 2015 does not start after the recent update on Mac Pro Yosemite

  After you download the last updated September 27, lightroom does not start on my mac.

  Used to work without problems so far.

  Tried to disconnect the last clouds and again without success.

  Thanks, that worked.

  Now, I have to do the update again hope that will work as well...

  Do you have any idea what caused the problem?

  Concerning

  Christian

  MIT thank wurde

  Hans Christian Behrendt

  2015-09-30 18:07 GMT + 02:00 rpandita [email protected]>:

  Lightroom cc 2015 does not start after that a recent update on Mac Pro Yosemite creates

  by rpandita https://forums.adobe.com/people/rpandita> in * Photoshop

  Lightroom *-see complete discussion

  https://forums.Adobe.com/message/8015642#8015642>

• HP DV7-7259nr does not start after the BIOS update

  Hello

  I have a problem with my HP DV7-7259nr laptop, WIN8 running: it does not start after tune recommended to update BIOS and drivers.

  It downloaded all the drivers and started installing at one time, he asked for a reboot, click OK and the BIOS update has begun to load. The process ended successfully and after the reboot that my laptop wouldn't start; everything is black and the cooler is runing.

  I tried:

  -battery disconnected and power - button Power - plugged power again-> NOTHING

  -Windows key + B + Power button--> nothing

  Please help as this is the laptop I use daily in my work.

  Thank you

  If you install the electro mechanical original hard drive in it starts?

  If it has been delivered with a SSD?

  The specifications indicate that an electromechanical drive was part of the specification.

  

  This is where lies the UEFI environment. It is actually on the hard drive.

• Photoshop Element editor 12 does not start

  A few days ago I installed Photoshop elements 12. It worked fine, but today I decided to re - roll my system to the version before the installation of PES. After you have reinstalled PSE12 I could not launch editor - Organizer works very well.

  The editor does not start if I try to opent it directly from file .exe, organizer or home screen. In task Photoshop elements editor program manager is displayed for a few seconds, later PDapp.exe appears and nothing happens.

  I tried to reinstall the program by removing all records (also the "AppData" folder) but it did not help.

  No idea how to fix?

  I decided to restore the system because of a few short weird hang-ups (1-3 sec.). They began after last windows installation updated.

  I use Win 7. I tried normal normal uninstall.

  Finally, I deleted some folders in CommonFiles/Adobe connected with PSE12 and with the license and then Manager after reinstallation of PSE, I need to connect to my Adobe account and everything works fine now.

• Tecra 8000 does not start after the BIOS update

  From one day to the other does not start my Tecra 8000 (400 MHz/256 MB BIOS 9.30 for years). After start-up, the disc starts to turn, but the screen including the backlight remains completely black, without red logo TOSHIBA BIOS is not accessible.

  I got a new mainboard on stock, so I replaced it, and it worked. Unfortunately now my WLAN card now did not work properly. I tried several settings of the BIOS with no results, so I decided to do an update of the BIOS from 7.50 to 9: 30. After the upgrade, I get the message "ROM WRITE successful, utility completed. LEADER BIOS: Tecra8000 v 9,30 ". Because what either kept silent, I pressed the power button to restart and heard a long and many short beeps (endless). I could interrupt what pressing the powerbutton for 5s.

  After turning on again I have the same problem as described in the first line :-( I can't get into the BIOS, but I can again update (with pressed F12). Once again these beeps.

  What to do with these beeps after average BIOS update? I replaced the MoBo connector LED with pension. Processor, memory, keyboard and HD has remained the same. So, before I start disassembling the machine, please notify, your help is very appreciated.

  Hello Joachim

  I'm not a technician and don t know what the beeps but I am afraid that the BIOS chip is damaged. Because of this, the unit is completely dead. Sorry, but I really don t believe you can do anything. Maybe the new motherboard again :(

• A series of satellite does not start after the BIOS update

  After update bios with the downloaded utility my laptop does not start.
  Do you have this case covered by the warranty?

  I'm not sure if this would be covered by the warranty. You must contact the ASP in your country for details, but I assume that it s not covered.

  PS: Did you try this work around:
  -remove the battery, disconnect the adapter
  -wait ~ 40 min
  -connect the two devices again and try to turn on the laptop

• HP compaq 6510 b does not start after the BIOS update

  Hello

  When I turn on my laptop HP compaq 6510 b it DISPLAYS this message: your bios has not finished updating 6510b.after flashing the bios of the laptop does not start .it displays the same message (your bios did not complete the 6510 b update) and turns off. I cannot access the bios by pressing F10.the bios version was F16 and flash by F20 .will help thank you very much.

  I'll have to return a verdict of laptop motherboard bricked due to a failure of the BIOS upgrade. Sorry, but it happens.

  This means that this would require the replacement of the BIOS chip to make it work again.

• Satellite L50-A-160 does not start after the Bios Update

  Hi, first of all, this is first post.

  I have 2 satellite L50-A-160 with bios 1.1

  Problem: seems to go to sleep after a few minutes, even working on them (even with both)

  So, I found an updated version 1.9, downloaded and running on one of the laptops. the biosupdate tool found matching the BIOS and a race.
  In the middle of flashing, he fell asleep. turned on and not start. What can I do? Recovery options? I guess the same thing will happen with the other too...

  What is the problem with these computers?

  Besides; very poor battery, always shows 0% available and not charging...
  Does anyone have a solution?

  Best regards
  -always in the hope.
  GT

  Have you tried to change in Power Options?

  See screenshot and try to change the ones I marked (it can refresh the settings, just change the values) and see if this solves the problem.

  

  and for the other laptop with no boot, a laptop sleep by updating the bios will surely mess it.

  what I don't understand is why your sleep laptop BIOS update, as far as I know the sleep settings is active then on windows (since this is controlled by windows)
  He does not sleep while in the BIOS you leave 1 year, sleep settings active only after loading windows.

  have you tried to check the time of processor for your laptop? Maybe its overheating causing auto-off

• Satellite A100 - BIOS and Windows does not start after the BIOS update

  Hello, I extend my Satellite A100 laptop BIOS.

  After update, I can't start my laptop and the BIOS will not start.

  You see the Toshiba logo?

  Was there a power failure when you updated the BIOS?

  Try to remove the battery and the adapter and leave for a few hours. You can also try reinstalling the RAM.

  If this does not help, you will need to send it to a Service Center for repair.

• HP Pavilion dv9260nr does not start after the bios update

  After the HP Health Check, it was recommended that I have updated to the current bios.  After you have downloaded and installed, the computer would not start.  Instead, it emits a long beep and 2 short beeps and the screen is blank.  How can I recover a bios update failed?  Is there a way to return the computer to the bios Setup?

  I thought I would post here to help others as I just spent 5 hours to fix this problem. I have personally experienced this on two different computers, both are model DV9260NR. I woke up in the long and short two beep power. The first time it happened, I tried to fix the BIOS by using the recovery disk, but it didn't work. I tried this using a USB floppy like any other player. The floppy drive should get accessible, then machine would be on a second beep then stop, but it would remain under tension. The first time around I gave up and eventually return it to HP as it was under warranty. This time above the current problem computer is more under warranty so I decided to test out of old college. After trying several discs crisis different Phoenix, I finally found one that worked.

  I downloaded crisdisk.zip here:

  http://www.mediafire.com/?3ccb9m0kv0m

  Followed by the latest bios from HP for the DV9260NR

  FTP://ftp.HP.com/pub/SoftPaq/sp42001-42500/sp42187.exe

  I used 7 - zip to extract the files in sp42187.exe and crisdisk.zip

  go to the folder where you extracted sp42187.exe and rename it to 30BBF2D. WPH into the BIOS. WPH

  Copy BIOS.wph to the folder where your snippet CRISDISK.zip

  I have created my disk in Vista, so don't worry about going "Real DOS".

  YOU MUST USE CRISDISK TO CREATE THE DISC!  SIMPLY COPY THE RIGHT FILES ON A FLOPPY DISK DID NOT WORK!

  Open a command prompt, I used command.com not cmd.exe

  CD to the folder CRISDISK.

  At the prompt enter: "CRISDISK. "BAT HAS:

  Finally, put in a blank disk and follow the instructions.

  Once the disk created, slap this puppy in a floppy USB drive and plug it into the computer.  I didn't need to use as or Windows + B, B FN hotkeys to trigger the BIOS recovery. The system entered in the BIOS for me recovery mode and tried to access the USB floppy.  I noticed that not all USB ports will work.  I plugged my USB stick, floppy to the next to the power supply.  If all goes well just turn on the computer with connected USB floppy drive and the disc in the drive. As before the system beeps once per second during playback of the disc.  The disk activity, arrested again, but this time that the system kept beep immediately after discontinuation of access to the drive.  These beeps point you out that the BIOS is flashed, it's just leave turn. When it was made the machine itself set off.  If yours is not, so I doubt that the BIOS recovery will succeed. I then unplugged the USB floppy drive, turned on again and to my surprise I was greeted by the HP and the BIOS logo!  I hope this helps people difficulty of their DV9260NR.  I met four dv9260nr machines and two of them does not update the BIOS using WinPhlash and the finished machine trashed, not good statistically.  I hope that others with the same model will be able to get their machinery running. I'd be curious to know if it works for others.  Post here if you are or do not succeed using this procedure. Good luck!

• 6 Lightroom does not start after the last update of victory 10

  Hello

  After installing the latest updates of victory 10 yesterday my 6 Lightroom won't start no more. I tried to reinstall, fact the renaming of files SLCache and SLStore, past all antivirus and firewall off the coast. No results on the start screen, I always get a pop up saying that LR does not work properly because of the problem and that patients be informed as soon as there is a solution. It stops...

  Can someone help with this problem?

  Hi jensk

  Name the module fehlerhaften: ig7icd64.dll

  Update your graphics card driver.

  ig7icd64.dll crashes due to a deprecated module / driver for your graphics card

  Concerning

  Assani

• Sir my network smart vaio does NOT start after installing windows 7 ultimate 64 bit

  Sir accidentally my real Home Basic 64-bit is formatted when installing Ubuntu 13.04 in a separate disk.

  I have no backup to restore the window as recovery is also formatted.

  I installed windows 7 ultimate 64 bit and all drivers related to it is on th website:-http://www.sony.co.in/support/product/sve15115en/download

  including the original software and driver patches.

  but after that my network manager smart vaio does not work its present only in the menu start when I clicked it nothing happens.it nevers opens.

  Please help me

  do a system restore disc. contact https://www.sony.co.in/section/contactus

• Portege Z930-118 does not start after the BIOS update

  My PORTEGE Z930-118 failover and wont start after I upgrade in the middle of the upgrade I remove power, then press stop down after I see the power and wireless but the screen stays black?

  Any help please

  In this case the EPROM has to be reflashed once more using crisis disk BIOS.
  Usually this must be done by authorized maker Toshiba. But of course this will be possible only if the EPROM module has not been too bad.

  What to say: try procedure (link above) posted by Bob. In which case it will not work, ASP is your next contact point.

  Good luck

• Helix died on me, does not start after the BIOS update

  I just did an update of the BIOS the other day. No idea what version it is. When I started it it said "error detection on the HARD drive...". ». I have since reset the BIOS by default options, and now it starts with a splash BACK-like screen that shows the disk ATA HDD0. But selecting and pressing on enter flashes just the screen and nothing happens.

  When I attach a USB with Linux, it appears in options on the BACK-like boot screen, but the selection does not to start.

  The laptop is now completely uselss and I lose the days of time and this is a major problem. What should do?

  Hello. Assuming that you have not clean installed a new operating system, and you have the

  Win8 original installation on your propeller.

  Enter the BIOS Setup by pressing F1 when the Lenovo logo appears.

  Go to Security - Secure Boot and set it to off if you want to start any OS other than Win8.

  If you are happy with just the Windows 8 running on it, then I recommend Secure Boot for the value IT.

  Go to start - Boot - and on top must be Windows Boot Manager.

  With Secure Boot set on, Boot to the UEFI/Legacy is grayed out and set to UEFI.

  With Secure Boot set to off, and you want to boot other operating systems, like Linux, it must be set to both.

  Check these settings and see if your computer boots.