Photosmart calibration 6510

Similar Questions

• Photosmart HP 6510 - can't find the USB port to connect to the computer. It is right in front of my face?

  Photosmart IHP 6510 - can't find the USB port to connect to the computer. It is right in front of my face? I can't find a diagram online. do not have wireless capability. With the help of MacPro with Snowleopard.Thanks.

  Hello

  The usb port is not #22. as seen in the picture. It's in the back of the printer on the side right hiand.

  

  Best regards

  ERICO

• Can print but cannot scan Photosmart HP 6510

  After being able to print and scan at my Photosmart HP 6510 my VIAO laptop Ultrabook, for some reason, I lost the ability to analyze.  Whenever I try, I get the error message "the scanner is currently in use. Wait until your previous task is completed, and then try again. "The problem is the scanner is not in use and I do not see how to delete it.  This same printer/scanner device other users can connect their computers and scan from it.

  What program you use to create the scans and what file format you saved scans - PdF, JPG, TIF?

  I suggest using assistant installation automated HP.

  Go to http://www8.hp.com/us/en/troubleshooting.html

  Work carefully through the steps to detect your printer through the option to allow web service from HP to install the necessary drivers.

• New cartridge for Photosmart HP 6510 appears defective

  I just replaced the old magenta cartridge in my Photosmart HP 6510 with a brand new printer, pack of 4, and it is now telling me that or toner appears to be missing or damaged. The new cartridge looks in good condition and is broken down and repeat the relocation or power off the printer do not help.  I tried cleaning the contacts, but everything seems very clean.

  I managed to get the printer working again with the old magenta cartridge up to who has certainly missed, but now the same error is detected, leaving me with a printer that does not even to print only black.

  I bought the original cartridge in a pack of 4 from Amazon, so have little chance to return the fauly cartridge (even though they agreed it was defective).  Looks like I'll have to do a magenta and hope that works, but in the meantime, has anyone any ideas how I can persuade the printer to work using only in black?

  Hello

  There could be two possibilities for that matter, ink cartridge you bought or print head.

  Try installing the old cartridge and check if the error.

  If Yes, then his problem with the printhead, and the printer must be replaced under the print head is fixed part this printer.

  If not, then the new cartridge is defective contact, HP Technical Support for assistance. If the new cartridge genuine HP, then iam sure Technical Support should help you get the repalced the cartridge (if you are in the United States).

  Please call the HP Technical Support for assistance.

  If you are in the United States, the toll free # is 1-800-474-6836.

  If you're not in the United States, and then connect to www.hp.com , bottom left it is an icon of the world map, click it and then select the region that you belong to, which would then provide the support options for you for this region.

• How can I print on legal paper with a Photosmart HP 6510?

  I have the opportunity to print on legal size paper.  The status bar for my Photosmart HP 6510 does not develop to take into account the length of the paper (at least not that I can find).

  I found I can load a page in the tray, close the tray and it will print.  But it might mean loading of a page of a long document at a time.

  Is it possible to extend the trial of paper?

  I could not find a bin for paper for legal communication on the accessories page: have I missed?

  Is there another solution for loading several pages at a time?

  Alternatively, I'm stuck with a single page at a time?

  Thank you.

  There is an element if you swipe up will drop the lip on the inside of the lips of the paper, on the left side tray, front of the tray and you can load the legal document.  Hope that helps.

• Photosmart HP 6510 B211a works does not properly after power failure

  Hi guys,.

  I'm new to this forum, but I hope someone can help me.

  I have a HP all in one Photosmart B211a 6510, which worked like a dream, since I had last winter. We had an unexpected outage yesterday however and once the power came back, the printer insists on the fact that there is no ink in the system. I fear the worst and believe that his brain can be somewhat blurred.

  I have two of your ink cartridges replaced last week with genuine HP ones and everything was fine. My ink level is almost low on the other two, but I have not replaced these yet because it is not necessary.

  Once the power came back, the printer informed me that the magenta ink was 'missing or damaged '. I removed the cartridge, cleaned with distilled water and dry. Once replaced, the printer has changed his mind and told me all the ink cartridges are now 'missing or damaged '. When I opened the printer again, the transport of ink is automatically did not move as usual to allow me to change or remove the cartridges.

  More the touch screen of the printer does not allow me to leave this error message or perform any other function such as cleaning the heads. I tried a soft reset and hard reset, but this proved unsuccessful.

  He's tired? Should I just throw it and head to the stores again?

  Thanks for reading this,

  Fatiha

  Hi rich,

  I replaced the cartridge magenta yesterday and my printer works successfully again! Woohoo!

  My father, an electrician, so between us we have come to the conclusion that when the power came back after the crash there was an electric pick or insufficient tension than normal and this has damaged the chip of the nearest power - the magenta cartridge ink.

  All is well again in any case.

  Thanks for your help - I appreciate it

• Photosmart HP 6510 will only print black light gray text

  Any suggestions on how to solve this problem.  Been thro all the habit change the cartridges, clean the heads (several times), align the cartridges.

  Problem started after the low ink warning and then change cartridges.

  Need to BEST print mode to get the light gray black text only printer and printing grayscale value must be set to OFF, otherwise no visible impression is reached.

  Colurs look OK on the Test print but once again no sharp black, light not gray see the upward.

  Help please!

  Hi SportBilly15,

  Welcome to the HP Support forums.   I understand that your Photosmart 6510 is not printing black ink properly.

  I've included the document setting the streaks of ink, faded prints and other common print quality problems . It takes you through several steps to correct the problem of troubleshooting.

• Photosmart HP 6510: Black print failed

  I have a HP Photosmart 6510, which will not print black - pages of text, sound as if they are printing, but the page comes out blank. Watch as the color test page, but not black.  There is no error message.  Black print cartridge is full and I have applied all recommended maintenance procedures.  I'm going to disassemble the printer (which is out of warranty) and the print head to check the visible obstructions before deciding to give up completely and use my backup of Canon.  Can anyone suggest any other remedies or advice on removal of the print head?  Thank you.

  Thanks for your suggestions.  I removed and cleaned the print head, but the problem remains unresolved.  I did more research and decided to go deeper into the printer to access tubes empty below the print head.  I couldn't find all the instructions more complex procedure on the HP site or elsewhere online, so most of the work was intuitive.  I managed to remove the 'well' below the print head complete with 4 vacuum tubes, and it was immediately obvious to me that the black ink tube was clogged.  I went to clean the whole by immersing in hot water and using a syringe to flush out the tubes.  I cleaned too much ink frozen since sponges of drain that receives the excess ink from the vacuum system (no doubt mostly print head last cleaning operations).  After drying of the parts and reassembling the printer, everything is back to the fully functional State.

  I was amazed at the amount of vitriol expressed by users of the forum to HP for what seems to have been a recurring problem with these printers.  It seems incredibly useless to throw a sound mechanical printer because of a dried ink problem, but that's what many did the cost of 2-3 hours time technician to fix the problem simply cannot be justified. It is unfortunate that HP provides no instructions for technical people like me who are willing to undertake their own maintenance out of warranty HP products.

• Photosmart HP 6510: Personalized printing HP Photosmart 6510 problem

  I have read through a couple of threads and followed the instructions to turn on 'custom' on my HP Photosmart 6510 all-in-one printing. I loaded the driver of HP Deskjet 450, which finally allows me to select a custom size of 5.5 "x 8.25". I'm trying to print on wedding invitations response cards. Wedding invitations made the same paper 5 X and can be printed without adding a new printer driver for the 6510.

  Now that I can get the printer driver (deskjet 450) to recognize the custom format 5.5 "x 8.25" but I can't print. I use a model of design by Staples and get the following errors.

  Errors - the margins of Section 1 are set beyond the printable area of the page. Do you want to continue? I pushed Yes and the printer tries to print the job abd I get the error "paper mismatch". The printer actually determined the size of the paper when I adjusted the paper tray to accommodate custom size paper.

  Troubleshooting - I tried to adjust the margins, but I have little ability to adjust in the template provided. When I adjusted the margins, I always get the error "paper mismatch".

  Any ideas on how to do more troubleshooting?

  Hello

  Please retry the procedure which should solve the problem below.

  (if the printer is connected with USB)

  Click START > device and printer > add a printer > add a local printer >

  Select "Use existing Port" then Virtual USB from the drop-down menu, click on NEXT, in the production list, select HP / Hewlett-packard and in the right pane, select Deskjet 6980 and finish the wizard

  OR

  (if the printer is networked)

  Click START > device and printer > add a printer > add a local printer > choose "Create a new Port" > type in the printer IP address click NEXT, in the manufacture of the list, select HP / Hewlett-packard and in the right pane, select Deskjet 6980 and finish the wizard

• Photosmart printer 6510

  98% of the time that I print with black ink custom setting only in draft mode to save ink.  I noticed recently that was not only my black cartridge low on ink, but also that my color ink cartridges were low.  Is it possible that when the black ink cartridge contains ink printer is designed to use the color cartridges for black ink?

  There is color ink used when printing to keep open nozzles.  Color ink is also used for graphics unless you selected "black ink only.  If you print with photo color ink media will be used exclusively, black ink is not compatible with photo paper.  Color and black inks are also used, if you never tell the printer to complete a cycle of cleaning (rarely needed).

  The here document contains information on how the ink is used, the Photosmart 6510 is an IIC printer in the terminology of this page.

• HP Photosmart e-All-in-On 6510: can't install drivers Photosmart HP 6510, no matter what I try

  WIndows 10

  HP Photosmart 6510 e - all-in - One Printer - B211a

  So I've had problems printing from my computer wireless for centuries now. It seems that it only prints when he feels like it, don't know what to do to solve this problem, and do not know what I do to break.

  After laughing with the inhabitants of problems that I get when I try to print, I tried updrading the driver because there was an update available.

  First of all, I used the HP Installation Wizard, it would be about a minute or two in the download and just freeze. After a bit, he'd say he didn't and I had the opportunity to try again.

  After a few failed attempts this, I tried to download manually (using chrome) Web site, the download appears at the bottom of my browser and the beginning, but then after a minute or two, it would again, freeze. Leaving, it comes with an interruption of network error. I have tried both installing the software driver that is full of features, and then the base a few times. None worked.

  Tried to install HP Print and Scan doctor after reading a few articles support. But even once, uploading manually or via the installer of HP you freeze at some point and not work.

  After the age of back and forth between trying to get a single download to work, I open the HP Support Assistant App on my computer. It detected my printer and I added it. He had a mark 'important' and wanted to update my driver, tried to do it is there, started the download, the bar would go up a little, then stay at the download percentage.

  After a bit more supported pages, I uninstalled my driver curent computer, he got the error "Installation error 2081883401: failed to uninstall the device with serial number". "." Press you on ignore, he completed the uninstall, and then I restarted my computer.

  The aircraft has disappeared from my programs and the list of software (so I can't uninstall it again), but he still gets detected with HP Support Assistant, HP Print and doctor Scan that already seemed to be installed via the Support Assistant (don't know if this is normal).

  No matter what I try to do to download the latest driver from HP servers, just download stop and remain unchanged, at some point, until I cancel it or an error message appears, any program, I try to download it through.

  Don't know what I can do at this point.

  Any help would be appreciated

  -Josh.

  EDIT: well, I got it working again. Don't know what I uninstalled. Had to manually detect his IP through windows settings, and now it's just call itself class driver. Don't know why, but at least it works. Still can not update drivers through HP servers however.

  Hi @InterstellrJunk,

  Please become a member of the HP's Support Forums. I understand that you have a problem with the installation of wireless printer. I'll be happy to help you.

  Here are a few documents to help.

  Occur after Windows 10 upgrade, printer problems

  Printer not found during setup of the network (Windows) driver

  Please keep me informed of the progress of things.

  If you need help, let me know and I will gladly make all that I can to help you.

  Please let me know if that solves the problem by marking this post as "accept as a Solution. To simply say thank you, click the Thumbs up below!

  Thank you.

• Photosmart HP 6510 does not copy in black

  last week, I bought a photosmart 6510. install via the cd under windows 7 64-bit, after installation I downloaded an installed all updates. This morning I tried to copy some documents, but nothing on the page to black. managed diagnosed programms, doctor of hp, cleaned cartridges to level 2. just nothing works. When I touch the button to copy in color, it copies the colors, but the black part is unreadable. so, does anyone have a solution? Thank you

  There is a document with steps to help solve the problems of location printing here.

  If the steps in the document are unable to resolve the problem, then I suggest call HP for Technical Support on this printer. If you are still in warranty, HP can replace the printer without cost to you. I'll link the information to get in touch with them below. The link takes you to a form to fill out. Once you fill it and she is treated, it will give you the printers warranty information, a file number and the phone number to call.

  HP Technical Support call case form

• Photosmart HP 6510 using Mac OS x 10.8 - create multipage documents

  I have updated and installed the driver for the 6510 and I can print and scan wireless. I can't create multipage documents. In the past, I used the software "HP photosmart studio" with a previous printer (is more connected) to create multiple pages of scanned documents.  I can't find the printer when I search new devices in the program "Studio".

  How can I create multiple pages of scanned documents?

  Thank you

  Hello

  You can create multi-page scans using the HP scanning application, you can find it under Applications\Hewlett-Packard.

  Full scans by adding the necessary pages, at the end click on save to complete the analytical work.

  If you can't find the HP Scan means that the complete software has not been installed, you can download the software below, be sure to select the Software from HP recommended during installation:

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=MP-107204-2&cc=us&DLC=en&LC=en&OS=219&product=5058336&sw_lang=

  Shlomi

• Photosmart HP 6510: HP Photosmart 6510 cannot print in black

  Like everyone, I tried all the reset standard and practices of head cleaning.

  Can anyone send me please the new reset instructions?

  Hi @gpn44,

  Welcome to the Forums of HP Support!

  I understand you have a print quality problem with printer HP Photosmart 6510. I'd be happy to help you and don't forget to come back to this thread and check "Accept as Solution", if I have successfully helped solve you the problem. If you want to say 'Thank you' to my effort to help, click on the "thumbs up" to give me a Kudos.

  Looks like you did a lot of good troubleshooting already. You followed this guide, Printers HP Photosmart 6510 - printer prints blank Page or does not print black or color ink?

  I can send you the steps to perform resets itself, however, I don't think it will do everything for the same problem.

  The cartridge is either dirty, defective or the print head is clogged. This print head is not removable, customer, but if the printer is out of warranty, you can try the steps outlined in these videos.

  This video shows you how to do a manual print head cleaning. I suggest you to watch the two videos before proceeding and use at your own discretion.

  Video: HP 5510 will not print black and color - print head removed and cleaned.

• Photosmart wireless 6510 works very well, but how now to enable web services & eprint?

  New wireless photosmart 6510 works well with my laptop (Windows 7) to home & router; How can I activate the web & eprint services NOW? During the initial installation, I was short of time and I think that the antivirus intervened and I don't have a printer email address. He said that I could do it later - how? When I use the Web Services Panel to printer it tells me that I am not connected to the server.

  Is there a pure easy way to add web services now without upsetting my wireless network settings?

  bjhulse22,

  The steps below a usually resolve the problem you are experiencing:

  1. unplug the power cord at the back of the printer.

  2. unplug the power cord at the back of your router (and the modem, if they are separated from the router).

  3. wait 20 seconds, then plug the router (and the modem, if necessary) in.

  4. wait for 30 seconds, then plug the printer back and power.

  5. press the button on the front of the printer ePrint, and it should try to connect to Web Services again.

  These steps usually fix the problem, but if it persists, you can try definition of network information static for the printer (which is sometimes useful to stabilize the ability of the printer to get outside of your network to the internet):

  1. print a Configuration Page from network network printer or wireless menu.

  (Select the wireless icon, select 'Settings', select "Display Network Configuration", select "Print Info")

  2. open a Web browser and type the IP address of product (from the network Page of Configuration) in the address line. The HP - Embedded (EWS) Web server should open.

  3. click on the tab 'Network' (in the top menu), then click on the 'Networking' link (in the left menu), then click on the link "network address (IP).

  4. click on the small round button next to the "Manual of intellectual property", then fill in the fields with the information from the Page of Network Configuration (IP address, subnet mask and default gateway).

  5. under "Setting up the DNS addresses", fill in the fields with the following text:

  -Preferred DNS: 8.8.8.8

  -Alternate DNS: 8.8.4.4

  6. click on the "Apply" button and the settings must be updated. Once the settings are updated, turn the printer off and then back on.

  7. try to reactivate Web Services.

  Let me know if you have any other questions, please!