Photosmart HP 7510: I scanned a portfolio too high-resolution jpg. Any way to lower res w/o réanalysant 200 pages?

Similar Questions

• My page is printed too high. When you print the report of diagnosis of iMac, top of page letters are cut off the page

  I have a hp c310a all-in-one.  When you print cd labels, graphics look good on preview before printing, but when it comes to the printer off, the graphics are about 1/4 "too high, which leaves the low" 1/4 of my blank cd label.  I printed a report of quality Diagnostic print from my mac and it came out too high.  Cut the top of the report, it began printing until the paper is correctly positioned.  When you print the Diagnostic Report of quality printing directly from the touchsmart on my printer screen, the report will print very well.  I wonder if there is a setting miss me when I go on my printout.

  Hello

  This really sounds like a parameter of the wrong paper on the computer, type or wrong size setting can cause these issues, especiallly it seems to work perfectly when printing directly from the camera.

• 8610 HP printer all in one: how to scan with very high resolution 1000 dpi?

  I'm scanning pictures very old, very low (about 1 by 1"). On my 8610, the highest resolution I can apparently is 300 dpi. On my 6600 previous, I was able to get 1000 dpi? Is the 8610 really not able to scan at such a high resolution?

  Hello

  The printer supports up to 2 400 ppp, but only from the glass flat, while the automatic Deeder top of Document (CAD) is limited to 300 dpi.

  Open the HP Officejet Pro 8610 software and tap on scan a Document or Photo.

  Change the source of the default 'ADF' value to 'flat glass', then analysis higher resolutions will become accessible to the general public within the drop-down list resolution .

  Kind regards

  Shlomi

• Display of high resolution - too small UI elements

  Just got a Toshiba KiraBook - one of the first Windows laptops with a display high-resolution "retina-type". It runs at a resolution of 2560 x 1440.  4.4 Lightroom works fine, but some UI elements are simply too small to this resolution is comfortable - even with my reading glasses on. I know that some type of support 'retina' has been added in LR 4.3 - for MacBook, at least. Not sure if this applies also to Windows? If so, is there a setting I need to change?

  My resolution of Windows system fonts is set to 165% - but it does not appear that LR uses this system across its interface setting. Any ideas?  Thank you...

  LR 4.4, Windows 8 Pro 64-bit.

  I'm not familiar with the operation in high resolution on Windows, but "Added support for Windows at 150% and 200% of resolution" was one of the new features on the list of the LR5 beta.

• Photosmart 7510 will scan is more than several pages

  Until recently, our 7510 Photosmart would provide the ability to scan multiple pages in the scanning area.  Now the test page add does not appear in the scan area.  I do not see anything realted to turning this function on or off.  What has gone wrong?  How should I do?  Thank you.

  Hello

  Click on the HP scanning software scan a document or photo and then select scan to PDF.

  Be sure to check the option Preview.

  Make sure that the resolution is 300 DPI or below, a higher resolution will allow only a single page scanning.

  Now, click on the Scan button and check for the difference.

  Please let me know if that helps

  Shlomi

• Photosmart 7510 stop scan to PC (Windows7). Diagnostics and help have not solved.

  Printer - Photosmart 7510.

  System: I'm on Windows 7 home premium 64-bit, I have Norton 360.  Laptop is Acer Aspire.

  Problem - Photosmart 7510 - scan is no longer to the PC.

  Software won't uninstall (so I can ' t reinstall)

  Connect the printer software installation impossible (he always recognizes the printer on the network)

  Scanner not recognized.  When I click on scan HP he says 7510 series unrecognized.  If I click on manage scans devices/printers, nothing happens apart from hourglass.

  I lived all the online help and scan doctor and spent 3 days on this.  Nothing seems to fix it or repair.

  The scanner, printer and copier what worked first implemented, including scanning to pc.

  Now, everything works apart from scanning to PC.

  A few days later the scanner to the computer stopped working and could not be recognized if clicked (for example to allow the scan to PC function).  Scanner the doctor then tried to uninstall and reinstall the software.  The basic device HP software won't uninstall, whether through the HP program or control panel.  There after the reboot, even when supposedly uninstalled.  I tried to reset the defaults on the printer, turn off the power sector, removing the printer from devices and printers, fixing and cleaning the registry errors, checking all relevant WIA and CPP are restarted and automatic according to the directives of this help: http://h30434.www3.hp.com/t5/Scanning-Faxing-and-Copying/Photosmart-7510-won-t-scan/m-p/1749193/high... I followed all the HP help topics and have tried drivers updated and installation of HP.com.  My laptop was rebooted about 50 times in the last three days trying to get this resolved.

  When I click on the printer defined upward and the software it prompts you to connect the new printer.  It finds my 7510 (wireless), but says that it cannot install it.

  I can't do windows system restore, because there is no set of restore points.  I tried to disable firewall for connections and installation of the software.

  Various error messages appear:

  During the uninstallation using the control panel.

  "Scan to PC Activation App" needs closing (I can only find in the tasks of process manager I then complete the process)

  If I try to use the HP uninstall later said there is no uninstall HP.

  I have the original CD.

  Any ideas as to how my scan to PC to work again?

  Maybe this isn't the case in your situation, however, security software (firewall/anti-anti-virus/malware) can cause endless problems, depending on their configuration. Norton 360 is an extremely invasive program, part of what makes it so effective. But, get the settings to allow access install/uninstall the devices through 360 can be complicated. My advice before you try anything else, would be to disable Norton 360 (gives you regular intervals) then try Solution 3 in the Windows 7 of this troubleshooting document installation section:

  http://goo.GL/Qtbcf

• Scan slides to a hp photosmart mac 7510?

  I don't think there's a way to digitize slides to a mac at a photosmart hp 7510?

  No, not really.  To scan transparencies and negatives on the scanner needs a backlight behind the media to project the image on the scanner.  The scanner on your printer has only a white sheet behind the scanned images, so this won't work.

  There are several manufacturers that offer scans of slides or negatives for less than $200.

• Photosmart HP 7510: HP Photosmart 7510 stopped printing

  Hi all

  I bought my HP Photosmart 7510 in 2012 and, until recently, never had a problem with it.  I have a wireless connection.  My Photosmart HP 7510 stopped printing.  I checked with HP print and Scan doctor and followed the steps to determine the problem.   Check for levels of printing came out showing the colors of ink for all but the black cartridge.  I installed a new cartridge.    A new impression level check again showed no black ink level.   I followed the instructions for the cleaning of the printheads and waited as instructed.    I wnet to my printer a few days later and was able to print a few pages perfectly.  But after that, the problem started again.  Now, when I print a test page, I got only one or two colors showing but never in black ink.

  I not made any changes to my system, and there is no driver updaates.   I wait with my OS to Windows 10 udate but haven't yet.

  You can provide any assistance will be greatly appreciated.

  Thank you!

  Norfolkgirl723

  Hi norfolkgirl723,

  Welcome to the HP support forum.

  I understand that you use a HP Photosmart 7510 e-all-in-one printer with a Windows 7 and you had a black ink not printing not question you thought went away, but now it's happening again. I would like to help with that.

  If you do the function of cleaning head with the printer and printing that has no black on it, there is probably a problem with the cartridge or maybe the printhead itself. Here is a document of support for help with this question - color or black ink not print.

  Please let me know if that solves the problem, or if you need assistance.

• Can't log into my account on my HP Photosmart AIO 7510 eFax.

  Hi, I have a HP Photosmart AIO 7510, I can't connect my account Panel 7510 eFax or tablet.

  I can connect to my eFax account there's web page, www.efax.com.

  I contacted eFax, but as my account is free and the problem seems to be my 7510 & not eFax, they cannot help.

  Can anyone here please help?

  Thanks in advance.

  foxleys2,

  Check out this thread: http://h30434.www3.hp.com/t5/ePrint-Print-Apps-Mobile/Quick-Fix-For-Most-eFax-Issues-Photosmart-7510-amp-Envy-110-114/m-p/1654683

  The fix in this thread should get all this work for you!

• Photosmart HP 7510 C311A or CQ877B

  Hello

  Photosmart HP 7510 C311A or CQ877B;

  I just bought & installed on it, everything works fine.

  Except eFax.

  I recorded with ePrint.

  But when I try to register with the Panel AIO eFax, I get the error that my zip code is not correct, even though it is!

  I installed the WiFi and the blue led is always when the PRINTER running.

  I am a resident of Jersey, GB, England.

  Help, please!

  Thanks in advance

  concerning

  I don't know if this is the problem, but just a thought here. If you go into setup (printer control panel), preferences, then region/country, is it fixed for UK? If this isn't the case, I could see the postcode being a problem. As I have already said, just a thought.

• HP Photosmart d110a will not scan.

  HP Photosmart d110a will not scan.  The resettled drivers, checked, put off - tension, nothing works.  Using Windows 7.  Error message is ' try scan from computer or see the documentation.

  Hello smhbcd

  The current software and try to reinstall using the latest drivers from the website. The link below will take you to the page "Select your operating system". Do it and download the latest driver full features.

  Photosmart D110 software

• I have a Photosmart C6150 all-in-one printer and too HP software. I can remove it?

  I have a Photosmart C6150 all-in-one printer and too HP software.  I can remove it?

  I have HP customer Participation Program 7.0 (245 MB), HP Document Viewer 7.0 (3.09 MB), HP Imaging Device functions 8.0 (2.44 MB), HP Photosmart all-in-One software 9.0 (15.65 MB), HP Photosmart Essential (11.15 MB), HP Photosmart Prime Software 6.5 (245 MB), HP Photosmart, Officejet and Deskjet 7.0.A (44,35 MB), the HP software update (3.42 MB), HP solution Center 7.0 (3.09 MB). (see screen capture below)

  

  Hello

  It is to your liking, in fact BUT in the list if you want to use all functions, you must keep all except 'Participation program.

  Kind regards.

• a photosmart HP 7510 printing directly on a cd does

  A photosmart HP 7510 printing directly on a cd does

  Thanks for any help

  The all-in-one Photosmart 7510 does not support printing on CD or DVD.

• HP Photosmart more B210 - printing is too high on the paper.

  The text is too high on the paper.  I can solve this problem when you generate letters and reports, etc. by simply letting a larger margin superior, but I cannot produce sheets of labels.

  I tried to change the paper size under tray settings/Main properties/device of the "letter" to "A4" - click on apply and OK - but when I check that the setting is always "letter".  Don't know if this is causing the problem, but if the book 'Letter' measures are lower than those of the A4 paper, he could be--and I wondered why I couldn't set this parameter.

  The printer is related to the Windows XP laptop and desktop Windows Vista computers.

  I hope someone can help.

  If the changes are not stick when made directly in the driver, the driver is probably corrupted. Try to uninstall and reinstall the printer driver and software package. I'll link the latest version below. Let me know what happens.

  HP Photosmart full feature software and drivers

• Photosmart C410 series AOI - scan a Document in glass?

  Hello

  Customer has one of the highest machines, when he wants to scan a document, it can do this 2 ways, first by putting the paper in the tray and press the scan on the Panel before or, secondly, by putting the document in the document feeder and using the options of the HP Solution Center. In both cases, the analysis ends without any problem.

  If he wants to scan a document using the scanner glass - sometimes, the page is torn and could jam at the tray - and he tries one of the methods above nothing happens at all, its as if the glass is not recognized.

  If, on the other hand, it uses the HP Solution Center and selects "Scan of photograph" (as opposed to "scan Document") it diagonally, works without any problem at all.

  Can anyone throw any light on this for me? It can use the scanner at the same time, but not as he wants in the long term.

  Thank you

  KP, I recommend you to uninstall the software in the "programs and features" in your control panel. Follow this link below, select your correct model and the operating system, reinstall the software.

  http://goo.GL/OwS1T

  There may be a problem with the communication and coordination with your computer right now.

  Let me know if it helps!