Ping requests not to go out

Similar Questions

• SCAN VIP - it is suitable for the ping requests before installing grid infrastructure?

  When the SCAN VIPs are configured in DNS, before the installation of the network infrastructure, should it be answering the ping requests or not?

  Hello
  The short answer is no.
  See more detailed information here:
  {message: id = 9914135}

  Handle: user8860934
  Messages total: 65
  Total Questions: 33 (31 pending)

  Please close your thread when you get your answer, it is considered a good practice here.

  Best regards
  Levi Pereira

• List of Agilent E4980A E420 sweeping request not completed

  Hello

  I am Agilent E4980A RLC control with labview 8.6 GPIB to measure the ability for several frequencies. I was able to run the frequncies LIST SWEEPING up to 65 points with no problems. Buy if I want to measure more frequency points (say 70 points) then I got the error of request not completed-420. My LCR Meter works fine if I trigger it manually with 201 points of measurement (maxinum limit points of the LCR meter). I used the driver NI E4980a. Does anyone have the same problem? Thank you.

  Soon

  I have change the calendar from 10 seconds to 30 seconds and it works now. Thanks to you all. I really appreciated your assistance.

• Unable to ping a website in command line with an error message: 'ping is not recognized as an internal or external command.'

  Original title: ping does not work

  In the cmd box when I try to ping from a site, I get a message saying 'ping is not recognized as an internal or external command.'

  I entered the command as follows: Office > ping www.yahoo.com

  Dan Calic, salvation

   

   

  Thanks for posting your question in the Microsoft Community.

  I understand that you are unable to ping a website in command line with an error message: 'ping is not recognized as an internal or external command.' Correct me if I'm wrong.

  I imagine the inconvenience that you are experiencing. I will certainly help the question of fixing.

  To help you suggest several steps to solve the problem, I would appreciate if you could answer the following questions:

  1 are you facing problems when accessing Internet?

  2. have you made any recent hardware or exchange of software on your computer before the show?

  Please follow the steps and check the question below:

  a. click Start, and then type the three letters cmd in the search box and then right-click on command prompt and click run as administrator.

  b. type these commands and press enter after each:

  dir %SystemRoot%\System32\ping.exe

  path %path%;%SystemRoot%\System32

  Ping www.yahoo.com

  c. a report.

  Your response is very important for us to ensure a proper resolution. Please get back to us with the information above to help you accordingly.

• Import error! 6 of Lightroom. "Some import operations could not be carried out.

  Will not import card or desktop files.

  I am trying to import my usual CR2 files from my canon camera. Usually, I copy and secret to DNG files. All of a sudden NOTHING will matter. It is not the card or photos. I get an error window and the code of "certain import operations could not be carried out.

  I restarted, updated to the latest version (6.4) and it persists.

  Help!

  Hi Rachel,

  It seems that it is a matter of permission on the folder where you try to import images.

  Also try to change the Destination folder or give read and write access to the folder where you tried to import the images.

  Kind regards

  Tanuj

• I just bought Photoshop 11.  The serial number is not valid for out me of the trial.

  I just bought Photoshop 11.  The serial number is not valid for out me of the trial.

  You must contact Adobe Support by chat or phone when you have the serial number and activation problems.

  Here are some links to help get in touch:

  http://www.Adobe.com/support/chat/ivrchat.html

  http://www.Adobe.com/support/download-install/supportinfo/

• PXI-8186 is not to ping requests

  I apologize in advance because I'm rather new to LabVIEW and PXI hardware.

  I have a NI PXI-8186 controller who all of a sudden can be reached via the network.

  The PC is connected to the controller via a hub.  I was able to ping another device also on the hub as well so that the NETWORK PC card is OK.  Since then, more troubleshooting, I have the PC connected directly to the PXI via a crossover ethernet cable but still was also unable to ping.  Therefore, (obviously) I can't reach the controller in MAX as well.

  When the PXI starts, I see the following

  --------------------------------------------------------------------------------------------------------------------

  PhoenixBIOS 4.0 Release 6.0.6

  Copyright 1985-2003 Phoenix Technologies Ltd.

  All rights reserved

  Copyright 2004 National Instruments Corp.

  Controller OR PXI-8186

  BIOS Version 1.20

  CPU = Mobile Intel (R) Pentium (R) CPU 2.20 GHz 4 M

  254 M system RAM passed

  Past of 512K Cache SRAM

  Press to enter in SETUP

  --------------------------------------------------------------------------------------------------------------------

  To me, it seems that the controller is not fully started.  After a reboot, it remains in the State as shown above.

  I tried to enter the Setup program, but is not able to join the installer and I have the following message but it is never:

  --------------------------------------------------------------------------------------------------------------------

  Enter the CONFIGURATION...

  --------------------------------------------------------------------------------------------------------------------

  Other information:

  + The "PWR OK" LED on the PXI is green fixed.

  + The 'DRIVE' on the PXI system LED is off.  This does not blink even during a reboot.

  + Ethernet "10/100" LED on the PXI Green is fixed.

  + Ethernet "Act/link" LED on the PXI constantly flashes orange.

  What other things can resolve with my minimal experience with this hardware/software?  Is it possible to start in SafeMode PXI or which is available if I can get to the SETUP menu?  Do you recommend a reformat of the hard drive?  If so, how can I do this and how can I get the application about PXI?

  I think that the hard disk on the controller does not have.  I know for sure on Monday as I pick up a backup controller.

• ping request was not

  I observed a strange problem, I have a small work group based windows xp one of our xp machines has no ping response, for example when I ping from machine B to A ping is successful when I ping B to a ping and failure, then I checked the firewall on and off throughout ip address correct without viruses and spy goods found pls help me also I m impossible to browse a machine B machine

  Hello

  ·        Were you able to make a connection between two computers before?

  ·        What is the exact error message that you encounter when you try to access the computer?

  Method 1:

  I suggest you check in SafeMode with network you are able to access computers. Follow the steps mentioned below.

  a. restart the computer and keep tapping F8 until you reach the start menu.

  b. Select safe mode with networking from the list and press ENTER.

  c. check to see if the problem persists.

  Method 2:

  I suggest to disable the security software installed on the system and check if the problem is resolved.

  Note: Once done the test, I suggest you to restart the system security software and check if the problem is resolved.

  Thanks and regards.

  Thahaseena M
  Microsoft Answers Support Engineer.
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Nested with 2 management cards workstation + ESXi5.5 = not to ping requests

  Hello community,

  I recently stumbled upon a bug (?) strange:

  I needed to install several 1331820 ESXi5.5 in my computer and noticed that the management interfaces are not to ping/accessible queries if more than one NETWORK adapter is used for the management network. As soon as I remove/disconnect ping NIC begins work and the server is accessible.

  Have not tested multiple ESX versions yet but Workstation 10/09/11 suffers from this.

  Yet several descriptions of this question, but not solutions. A suggested workaround has been upgrading manual driver interface NETWORK of E1000 vmxnet3 but nothing is in my case.

  Someone has any idea how to solve this problem?

  The cause was found to be using linked clones.

  I reinstalled all my guests individually and separately, do not use any cloning and they work like a charm.

• My FF image search returns error "your - Jr b Lacrosse ontario - search could not be carried out with the requested search options. Reset search tools search results»

  Before moving to the new 4 FF, if I did an image search, I had all sorts of images on the screen. Now when I do an image search, I get an error about the reset code of my research tools. I googled this and can't find that one another that there must be a JavaScript error that I disabled it in accordance with the instructions - (I think).
  I really need my image search tool.

  Clear the cache and cookies from sites that cause problems.

  • "Clear the Cache": Tools > Options > advanced > network > storage (Cache) offline: 'clear now '.
  • 'Delete Cookies' sites causing problems: Tools > Options > privacy > Cookies: "show the Cookies".

  Start Firefox in Firefox to solve the issues in Safe Mode to check if one of the extensions of the origin of the problem (switch to the DEFAULT theme: Firefox (Tools) > Add-ons > appearance/themes).

  • Makes no changes on the start safe mode window.
  • https://support.Mozilla.com/kb/safe+mode
  • Troubleshoot extensions, themes, and issues of hardware acceleration to resolve common problems of Firefox

• Can Ping but not connect via Remote Desktop - how to change the settings of the outside LAN adapter

  I have a Windows Server 2012 machine connected to a Windows 7 Pro machine via a switch.

  Internet is shared on the Windows Server and the port sharing network has a static ip address. Similarly, the port connected to the Windows 7 Pro has a static ip address. I was able to desktop Windows 7 remotely from the server without any problem until very recently.

  Recently, I had to change some properties of the LAN on the machines and I was changing the gateway by default for the Windows 7 Pro, when I was hunting from my remote desktop session and I was not able to reconnect since. I don't know if I accidentally blew the subnet or the default gateway, but I know for sure that I do not touch the part of the parameters ip address.

  In addition, I can't ping the server computer but I am not able to connect via RDP. Please suggest any possible causes and solutions for this case. Both computers are remote and I can connect via the internet to the server computer.

  As my title suggests, I'm trying to find out if there is a way to reset the settings of the adapter LAN from Windows 7 to my server and proceed from that.

  Please let me know if you need more information.

  Thank you.

  RAM.

  Hi Ram,

  Please contact Microsoft Community.

  Problems with Windows Server 2012 are supported in the TechNet Forums. I suggest you send the request in Windows Server 2012 general Forums TechNet.
  http://social.technet.Microsoft.com/forums/WindowsServer/en-us/home?Forum=winserver8gen

  Hope this information helps.

• HP OfficeJet 6500 (not wireless) times out on the network after various periods of inactivity

  Hello

  As the subject says, I have a HP 6500 from JO that will expire after a random period of inactivity on the network.  It will not respond to print jobs, pings, http for its Web page requests, or scan nmap.  Stop/restart the printer temporarily resolves the issue until it times out again.  I think it is not related to drivers, because there is no need of drivers installed on a machine on the network.  Anyone has any idea on what this could be?  Has anyone experience this problem?  I have no history of problems of auto-negotiation on my network (I am dealing with devices at work who do not play nice with auto-negotiation, and the only option for them was to put it to manual), but just in case, I changed the setting manually set to 100 Mbps Full.  Having just done this, I do not have yet to see if this changes what anyone, but I want to see if someone else has all possible solutions.

  Thank you.

  It seems that the static IP address has been resolved - it has not yet expired since I put it.  It seems that he fixed - lease DHCP renewal seems to give this printer problems.

• Service request not getting associated with the Contact

  Hello
  
  We have an interface between the Web site of our company and Siebel On demand application, visitors can come to our Web site and submit a request by filling out a form with their contact information and their request. In turn, this creates a folder 'Contact' and a 'Request for Service' in the Application folder,
  
  'Contact', we used WSDL and v2.0 "Request for Service" WSDL as the webservice interface, we find that the Contacts and requests for services are created as that individual records, service demand does not get associated with the contact record is created?
  
  We are capture the following information under the heading "Contact".
  First name:
  First name:
  E-mail:
  Phone:
  Address:
  
  and the following information under the 'Service request'
  Product information:
  Object:
  Description:
  Type:
  Status:
  
  Should the specify us anything else under the Service request in the interface that will associate the Contact and "demand for services.
  
  Is it because in version 2.0, each object exist as separate nodes that we are facing this problem?
  This will be solved by using v1.0, is there a limitation any using v1.0, please specify
  
  You can call me if you need additional information
  
  Thanks and greetings
  Satish Kumar
  + 1-857-869-0239

  Hello

  When you create the Service request, make sure that you set the field "ContactId" so that the created contact is associated with the SR created.

  -John CRMIT

• How can I change the sound alarm on Apple Watch for night stand mode?  Light ping is not quite disturbing to wake me up.  Are there different sounds?

  The sound of the alarm on the Apple Watch is not quite disturbing to wake mode bedside table.  Are there different sounds/tones that I choose? Where can I do this? Or y at - it app for Apple Watch Nightstand that will provide different alarm signals?

  Hello

  It is not currently possible to customize ringtones for alarm on Apple Watch.

  If you want Apple to consider adding this option, you can fill out and submit the form here:

  https://www.Apple.com/feedback/watch.html

• After asking a website, I should keep the cursor moving on the working surface of firefox to get the next page if I am not it times out, I ask her

  After requesting a web page (site), I have to keep the cursor moving on the surface of work Firefox while the page is loading, if I do not have the demand for time and I ask her again. Why is there a setting or something. This was not always the case that in the last year, I would say.

  Hello khbaumsr, several other affected users have reported that it was a problem caused by malicious software on their pc.
  Please run a full scan of your system with the free version of malwarebytes and adwcleaner (these two security tools are free).

  Fix Firefox problems caused by malicious software