Ping using a specific interface

Similar Questions

• How to configure VPN remote access to use a specific Interface and the road

  I add a second external connection to an existing system on a 5510 ASA ASA V8.2 with 6.4 AMPS

  I added the new WAN using another interface (newwan).

  The intention is to bring more internet traffic on the new road/interface (newwan), but keep our existing VPN using the old interface (outside).

  I used the ASDM GUI to make changes and most of it works.

  That is to say. The default route goes via (newwan)

  Coming out of a VPN using a site to character the way previous (out) as they now have static routes to achieve this.

  The only problem is that remote incomming VPN access Anyconnect do not work.

  I put the default static route to use the new interface (newwan) and the default tunnel road be (outside), but that's the point is will not...

  I can either ping external IP address from an external location.

  It seems that the external interface doesn't send traffic to the - external interface (or at least that's where I think the problem lies). How can I force responses to remote VPN entering IPS unknown traffic to go back on the external interface?

  The only change I have to do to make it work again on the external interface is to make the default static route to use external interface. Calling all internet traffic to the (external connection) original

  Pointers appreciated.

  William

  William,

  As it is right now that you will not use the same interface you have road to terminate remote access unless you know their IP addresses by default.

  In one of the designs that I saw that we did something like that.

  (ISP cloud) - edge router - ASA.

  The edge router, you can make PAT within the interface for incoming traffic on port udp/500 and UDP/4500 (you may need to add exceptions to your L2L static) of the router. It's dirty, I would not say, it is recommended, but apparently it worked.

  On routers, this kind of situation is easily solved using VRF-lite with crypto.

  M.

• How is it that I can ping between ESXi vmkernel interfaces with the sizes of package exceeding the value set in my passage upstream and one located in my vmkernel port group itself?

  
  I have a 10 GB dell powerconnect 8024f the switch and the firmware is OLD, but the port config shows maximum frame size = 9000 to all cable ports

  2 guests ESXi 5.5 wired, build 1331820, put each host computer network is managed by a single port dual qlogic 8150 ANC

  When I connect to my windows VM to check my new 10 GB connectivity (it is configured for jumbo mtu = 9000 frames) and ping-l 8190 against ESXi vmkernel interface that was MTU of 1500, I get an answer without any packet loss... How can it be if the port is configured for only 1500 MTU?  I thought that the two vmkernel port group and vswitch properties must have 9000 mtu defined, it appears that the vswitch properties override the port group properties.

  But I know I must be missing something, a few important concepts, somewhere, because when I connect to ESXi via ssh I can ping devices with values greater than 8190 and not just windows virtual machines that reside on the same host where the ping uses the internal bus, but I am referring to the connections of the host of other ESXi on the switch management.

  In summary - how the VMkernel does ping and response to pings of bigger sizes greater than the value of the switch upstream?   and why do ping with large packets get answers when the vmkernel port group is always set at 1500, is this a bug or is this feature obsolete?   I remember specifically in ESXi5 that I had to configure the vmkernel port group and the vswitch for this property to work.

  Unless you specify "Don ' t fragment" (-f for Windows) you will be able to use any size package successfully.

  For ESXi, take a look at Troubleshooting ESXi Jumbo Frames.

  André

• COM/ActiveX by default or non-specific interface

  Let's say I have a non-Visual activex control that implements 2 interfaces: IStuffInterface and IStuffInterface2.

  IStuffInterface2 derives from IStuffInterface and adds a little more functions.

  IStuffInterface2
  + - Property2a
  + - Property2b
  + - Method2a
  + - IStuffInterface
  +- + Property1a
  +- + Property1b
  +- + Property1c

  In applications VC ++ I can usually try an IStuffInterface2 query and use it. If this is NOT available, I can do plan-B and try to mark for older, IStuffInterface and IStuffInterface2 to disable the related application functions. Even simpler, if the VC application ++ doesn't require something IStuffInterface2 I know that there will be held will be of all versions of the control.

  How do you do this in LabVIEW? So far, of what I learned about LV if you put a control or an activex on a panel refnum is somehow BINDED to a specific type library and the interface. He seems to want to say that if I create a LV application with the version of the most up-to-date activex control, the LV application does not work on a system with an earlier version (even if technically the old control can fill in the application control contract). Even if I don't do the application of LV uses only the methods and properties of the original IStuffInterface it seems unable to use the old interface if a more recent version, there is one on the system.

  How to make sure that an existing LabVIEW application will run with what version of the control is present on the system?

  What LabVIEW unconditionally with default COM interface?

  You can choose a particular interface programmatically? Then how configure you the pre-wired VI as the type information are unknown?

  Thank you
  R.

  Rastikan,

  Tell me if I'm wrong, but I believe that what you're looking for is cast... you can find a lot of information about it searching around the forums and knowledge bases, but these will probably help:

• URG: How can I force APEX to use the specific schema: spaces of work APEX_040100 or entitled to another schema?

  Hi all

  Here's the scenario:

  1. My computer crashed. were to return to complete export (expdp 11.2.x to impdp 12 c). successfully done.
  2. Configured ADR blah blah... can access the admin of the apex.
  3. Problem is: administration interface does not SEE my workspaces apex Apex (only the workspace IN-HOUSE).
  4. After investigation it seems that APEX (after the upgrade) is somehow configured / run with: schema APEX_040200 and not

  APEX_040100 (as I have improved Apex in the old database versions).

  
  

  5. If I'm running the following:

  ALTER session set current_schema = APEX_040100;

  Select short_name, display_name

  of wwv_flow_companies

  where source_identifier is not null;

  
  

  I SEE all my beloved workspaces.

  6 my questions:

  a. How can I force APEX to use the specific schema: APEX_040100 instead of APEX_040200?

  b. or are there other alternatives to assign these workspaces in the current environment?

  
  

  Concerning

  Etay G
  

  Hello Brad,

  Thank you for your response. Appreciated.

  • You are right. Indeed, this should be the correct answer:
    • I forgot to mentioned I tried this (before the procedure below):
    • (https://docs.oracle.com/cd/E59726_01/install.50/e39144/trouble.htm#BABCBEAD)
  • Yet, as I had a little corrupted environment Apex after import (impdp), COMPREHENSIVE database this method of revocation (above) has failed several times to me.
  • What solved my problem was is mentioned here: https://community.oracle.com/thread/2565074?start=0&tstart=0
  • Here's what I have (solves the problem):
  • Deleted APEX_040200 Apex 4.2 installation().
  • Text left in DB is the only APEX_040100
  • Then, the version 5.0.3 and it worked!
  
  More importantly, after the installation of APEX, all workspaces, users, etc. are automatically correctly resided in APEX.
  • I think that if you have only 1 version of apex corrupted in DB. It should work as well. Remove again, schema using the above script (check version) with caution (after backup, etc.).

  Kind regards

  Etay G

• How to load several files DBF table 1 target using only 1 interface?

  Hello, I am a beginner in ODI and I have a problem.
  
  I have several DBF / Foxpro files that is stored in a directory like this:
  2010_10/account.dbf
  2010_11/account.dbf
  
  All DBF files have the same structure, but stored in a different folder (the folder name is < year > _ < month >)
  
  I managed to create an interface to load a DBF unique for the target table and the source table is hardcoded in the interface. Ideally, the interface will take place once a month.
  
  How can I use the same interface to load other DBF files?
  
  I know, if the data source is a text file, you can link the resource name to a variable, and the variable can be set to a file name. But I can't do since I use a JDBC driver to connect to the DBF file.
  
  Any help will be appreciated

  Hello

  I have no idea on the DBF files, yet...

  What is create a variable to build the 'months' and then pass this variable to OdiFileCopy, move this file to a specific directory. Then run your interface to load this file into your database. Once the work is successful, you can delete the file using OdiFileDelete (optional)

  Thank you
  Fati

• ESA how to pin a specific traffic on a specific interface for mail flow?

  We have an ESA Ironport virtualized and normally he was running an interface on our DMZ, 192.168.1.200.

  On this DMZ, the firewall allows only the 10.1.1.10 to 192.168.1.200 internal mail server mail flow to and from, more obviously other traffic as DNS and web for filter updates.

  However, I would like to integrate with AD, so for this reason I had to connect to another interface on our LAN in vmware, and in config to Ironport ESA I implemented this interface on the local network of 10.1.1.200.  I have all services off the power on this interface, in order to access the web INTERFACE for spam or configuration still goes to the original interface of 192.168.1.200.

  Now, I've been able to communicate to the announcement and make an LDAP query, which is excellent, but now the incoming emails are hitting our exchange of the new 10.1.1.200 instead of the original 192.168.1.200 interface.

  When exchange sends an e-mail to, it still sends to 192.168.1.200, and Ironport addresses correctly.  But what Ironport receives by email is now send to Exchange on the new internal IP address.

  Question is can pin it so that Ironport works the 192.168.1.200 (management), the interface for all SNMP traffic?  The ONLY reason I added an internal data interface 1 is to query AD.

  Is it safe or not?

  Thank you!

  Hey Keith,.

  The details provided, I pray that ESA uses the right interface to send emails to your exchanges (192.168.1.200) instead of 10.1.1.200.

  (Assuming that the 2 interfaces, one for generally more traffic, another for only AD queries.)

  I advise you to change the following.

  GUI > System Admin > LDAP > change the LDAP interface for usage (for queries) to your new 10.1.1.200 (if you haven't already done so).

  Then, CLI > deliveryconfig

  Change the interface used for deliveries of mail to the 192.168.1.200 interface (chosen by name).

  I think that should correct the behavior.

  Kind regards

  Matthew

• Aironet 1240AG - cannot use the web interface

  I'm trying to set up a new Aironet 1240AG. After that she won an IP from the DHCP in my LAN, I can always connect using the web interface. I use an Internet Explorer 6.0 on Win 2000. It keeps telling me cannot find the server. Please I need help

  Hi Olivier,.

  First off you're welcome :) This method really works without the need for a WLC, be patient. Check the address static IP put you on your TFTP (* range 10.0.0.2 to 10.0.0.30)

  Rename the access point image file in the folder of the server TFTP c1200-k9w7 - tar.default for a series of 1200 access point

  Looks like a problem TFTP (no firewall on your PC?)

  Take a look at the details in the following threads that each has to do with TFTP. There are some great tips to troubleshoot TFTP some of my NetPros favorite ScottMac, Cisco's Stephen and Jack Young. The likely culprit may be you need to uncheck "Hide extensions for known file types" on your server TFTP;

  http://forum.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Wireless%20-%20Mobility&topic=WLAN%20Radio%20Standards&CommCmd=MB%3Fcmd%3Dpass_through%26location%3Doutline%40%5E1%40%40.1ddc042b/8#selected_message

  http://Forum.Cisco.com/eForum/servlet/NetProf?page=NetProf&Forum=Wireless%20-%20Mobility&topic=General&CommCmd=MB%3Fcmd%3Dpass_through%26location%3Doutline%40%5E1%40%40.1ddc03c4/2#selected_message

  http://Forum.Cisco.com/eForum/servlet/NetProf?page=NetProf&Forum=Wireless%20-%20Mobility&topic=General&CommCmd=MB%3Fcmd%3Dpass_through%26location%3Doutline%40%5E1%40%40.1ddbf271

  I hope this helps! Good luck!

  Rob

  Remember messages useful rate...

• Make a request to use a specific adapter for the internet. Question

  Hello, I was wondering is there a way to make specific application to use a specific Internet adapter?

  I had three devices. Two wireless devices and an Ethernet.

  Well to put it in terms I want to choose which programs use adapter. For example, I want my browser to use wireless, my Messenger to use the other device on the Ethernet device and wireless, Skype.

  Is there an app to allow me to do this. Maybe some application tunneling or something. Maybe I can manually config windows to do this. If not, I can use Loopback Microsoft Map to loop and their tunnel. But there might be something that can already do what im asking the subject.

  I'm sorry, but there is no way to assign a program to a network card (or vice versa). Boulder computer Maven
  Most Microsoft Valuable Professional

• Cisco ezvpn ASAs cannot ping each other inside interfaces

  I have a set ezvpn in place with a 5506 (position B) client-side and a 5520 (location A) server-side. I have successfully connected vpn, and traffic flows. My problem is that I can't SSH in the location b. investigate this more than I can not ping is within the interface of the ASA opposing, or the machines inside each ASA ASA.

  I found the following links that describes a scenario similar to mine, but nothing on one of them helped me.
  http://www.experts-exchange.com/questions/28388142/cannot-ping-ASA-5505-inside-interface-across-VPN.html
  https://www.fir3net.com/firewalls/Cisco/Cisco-ASA-proxy-ARP-gotcha.html
  https://supportforums.Cisco.com/discussion/11755586/Cisco-ASA-VPN-established-cant-ping

  I joined sanitized versions of these two configs. Any help is appreciated.

  Hi Adam

  The site of B I'm not able to see "management of access to inside. Please try to set up the same. He could solve the problem.

  Also on the instruction of the ASA takes place nat can you please try to add keywords 'search non-proxy-arp route'.

  something like:

  nat (inside,outside) source static (Location A)_Networks (Location A)_Networks destination static (location B)-remote_network (location B)-remote_network no-proxy-arp route-lookup

  as I have noted problems with inside access to interface via the VPN when those keywords are not applied. If I remember correctly 8.6.x ASA version had a bug regarding the same. Cordially Véronique

• Windows to use a specific application to open a file with a MCD.

  Original title: "open with" application "Choose default program" Cancel

  I accidentally changed the icon and the program using the "open with" application "choose default program" to the word instead of VectorWorks. The central database file can still be opened by the program. However, I can't find the program or its icon on the 'recommended' or 'Other' menu programs even if the program is located in my folder "Program Files". How to cancel the global setting or that the program "open with" to recognize the program?

  Hi John,

  Thank you for writing to Microsoft Communities. From your problem description, I understand that you want Windows to use a specific application to open a file with a MCD. Please correct me if I misunderstood.

  John, I understand how it could be frustrating when things do not work as expected. Please, I beg you, don't worry I'll try my best to resolve the issue.

  Please follow the steps mentioned in the article to set the default application.

  Change the programs that Windows uses by default

  http://Windows.Microsoft.com/en-us/Windows7/change-which-programs-Windows-uses-by-default

  Please complete all of the recommended steps and if after following the steps to issue still persists, please come back to us and we will be happy to provide you with additional options available that you can use to get this problem is solved.

  If you are unable to perform the steps mentioned above, I recommend you to contact our live support by clicking on the link http://support.microsoft.com/common/international.aspx?RDPATH=dm;en-us;selectassist&target=assistance

• Anyone who has a problem with the system crashes when importing using the new interface to import

  Anyone who has a problem with the system crashes when importing using the new interface to import

  Can specify you what Adobe program you use so that we do that your post is in the right forum?

• In Camera Raw 8.4.1 I can open the DNG for 3 years, but it's using the old interface and features not the current - how can I change this. Rebuilt the cache.

  Creative cloud running on a HP with 18 GB of Ram - I'm working on a project using DNG 3 years old and when I open in my current Camera Raw, it uses the old interface with 'contrast' down and "valorisation" below 'exposure' - How do Camera Raw to open with the current interface?

  Thanks for any help.

  Craig

  If you are referring to the version of process , you who set the ACR camera Calibration tab.

  

  Also remember that all images with previous settings will show the process used when they were stopped.  Which can also be changed in this tab.

• check box use the temporary Interface as a derived Table

  Hello
  in some guides and oracle websits, they want to check the box use the temporary Interface as a derived Table (Sub-Select).
  but the topology and datastor KM or target, I can't click on it...
  is - anyone know why? what setting I need to change?
  
  reason
  I want to create a temporary interface to use as a source.
  MySQL-> temp. interface-> join oracle of temp table. interface.
  
  Thank you..
  Michael

  Hi michael,.

  When you create a temporary interface, an interface in which the target data store does not exist, you can then use this temporary interface as a source in a different interface. Once you add the temp as a source interface on the mapping tab, select the temporary interface. You should see the check box in the Properties window of the Source to 'Use the temporary Interface as a Derived Table (Sub-Select)'. To use the code integrated into the interface of temp, check this box. The code will then be added as a subselect for this interface.

  See this post for more details: http://www.rittmanmead.com/2011/06/odi-11g-new-mapping-and-interface-features-part-1/

  Enjoy!
  Michael R.

• Is it possible to add a hard drive to a VM running via a script or a program without using the user interface

  I'll try to ask this question clearly, but I ask that read you it carefully, because I can't do a great job of setting out clearly what I'm looking for.

  I know how to create a virtual disk in a batch file or a script.  I know how to have a running virtual machine to detect a newly added hard drive and format it in Linux, BACK, and NetWare. I do not have scripted this part, but I did it manually by adding records via the UI and then by doing the steps manually to make the operating system to detect and format the newly added drive. In each case, these steps are scriptable with the exception of the addition of the drive in the user interface.

  The only way I know to add a new hard disk to a virtual computer running is through the user interface. I don't know in a way that can contain script (for example vmrun or an API call) to make.

  I guess that maybe I can have the virtual machine to go into sleep mode and then add the HDD in the vmx file while the machine is in standby mode, then put the computer to sleep mode, although I have not tested this.

  My question is, ' can a virtual drive be added to a virtual machine running without using the user interface and without put the machine to sleep, or in other words in a script any?

  Have you tried VI SDK?