Pinout for PXI-2535

Similar Questions

• Where can I find the pinout for remote 8-pin Hirose connector?

  Where can I find the pinout for remote 8-pin Hirose connector?

  Pinout and wiring info is in Maintenance manuals (the same for all system cameras, series F, XDCAM, etc.),-ask at your local Sony Office if you want the info.

  The distance of 8 pins is for connection of remote control Sony RM-B150/170/750 panels.

  For the cameras on the system, the same protocol is used between CPR panels, MSU, CPU and camera heads.

  It is thus extremely difficult to hack numbered system!

  The B170 RM is the perfect Panel to work with the PMW-F5/55. It will give control of paint to paint base white & black R/B, Master Pedestal and Iris with the correct lens (Cabrio etc.). It can also control remote Rec stop start.

  Best regards, Clive. Sony ANZ.

• programming for PXI-6071e with SCXI1125

  Dear all,

  I connected the SCXI-1001 chassis with card Conditioning SCXI-1125 and SCXI-1327 block with PXI-6071E PXI-8176 with SH1006868 cable controller card. I chose the SCB-100 for PXI-6071 accessories, as there is no option to select SH1006868. I connected the Thermocouple on the SCXI-1327 block terminals.

  I am new to LabView, can someone guide me how to program. If anyone have example program, it will be useful to start learning

  Thanking you

  Concerning

  -Vishnu

  I don't think that you can select your accessory cables. Only the blocks for DAQ cards will be available on your list. Instead of the SCB-100, you can select the terminal box 1327? For starters, labview has a number of application examples. Go to the Help menu and select 'Search examples' then search for thermocouple. There should be examples on how to acquire tension of a thermocouple, graphic of your data readings, etc..

• Many DAQ cards synchronize hardware for PXI

  I recently went through the process of getting several PCI DAQ cards in a computer and synchronize them together using a RTSI cable.  I just bought two similar cards in PXI.  I had to add a RTSI cable DAQmx devices manually in the measurement and automation software, and connect the cable with the PCI cards.  I want to just make sure that I don't have to do the same with the PXI cards because there is no necessary RTSI cable for PXI.

  Thanks for any help,

  Mike

  The PXI chassis has backplane triggering and clock lines so that you don't need the RTSI cable.

• Current minimum for pxi-2529

  Hi all! I have the PXI-2529 matrix, and I intend to use it this way: I have a set of magnetoresistifs sensors connected via matrix switches to DVMs (see photo). I need a few times (such as 1 - 100 times a day) to change these connections. Here's the question: one of the parameters of the matrix is common minimum and it is 10uA. I want to understand what is the reason for this setting? (is this leak or something else), and what is that means that the matrix will not work if DVM internal resistance will be large enough, and current jet matrix mixers will be less than 10uA?

  

  Hi store,.

  To answer your questions, yes the minimum current is very similar to current humidification, this is the current that is needed to systematically knock the junk of the relay to check that it continues to work properly.  Using switches OR defines the minimum current as "the current minimum" which can flow reliably through the switch  So, while you will probably be able to measure a signal, even if you're not fulfills the minimum requirement, we cannot guarantee behavior of your switch if you operate out of specifications.  If you're running the specification current minumum for long periods of time, the resistance of the relay contacts will increase over time, and your relay will eventually become unusable.  Essentially, by non-compliant to the specification, you will shorten the life of your relay.

  As for your question, "is to say that after a few years of this matrix using the conductive oxide become big enough and I'll lose the connection?"  The answer is Yes.

  I hope it's a bit more clear, let me know if you still have questions about that though.  Have a good!

• Remote access for PXI with DAQmx

  I have a PXI chassis with a real-time embedded (PXI-8186) controller and some modules DAQ (PXI-6259) x 2. I've been programming this via LabWindows with a kind of client-server of RT - UI thing by using network variables and others. For some applications, it would be enough and more convenient to be able to interact with the PXI hardware directly from a connected PC network DAQ.

  The controller running a VISA server, it seems that I could connect to a remote machine with a kind of viOpen ("visa://pxi.somewhere.com//PXI0::15:INSTR"); ") and then contact a particular data acquisition card. But I can't find any information on the programming of the 6259 in any way other than DAQmx or similar.

  First question then: is the interface PXI - 6259 VISA described anywhere?

  More practical would be to continue to use DAQmx, through something like DAQmxCreateDOChan (taskHandle,"pxi.somewhere.com//Dev1/port0/line0:4",...)

  I found references to what we call 'Remote access appliance', for example:

  http://digital.NI.com/public.nsf/allkb/5CC9792C6CD4A34C862565BC0072D5DF

  that seems to put in place something equivalent, but I don't find it to watch it in MAX:

  Start-> all programs-> National Instruments-> NI - DAQ-> the remote device access server

  and I've seen suggestions that maybe it isn't that for traditional DAQ or only pre 7.0, or in any other way was no longer applicable.

  Second question: "Remote device access" are always and how to I install/activate it on my PXI controller?

  Someone at - it clues as to the foregoing, or any other way to get the same kind of features?

  Thank you

  Mike Schacht

  LANL

  Hello Mike,.

  Remote device access was a feature in NOR-DAQ traditional long just now.  This feature was not worn on OR-DAQmx because the framework it was built on does not really correspond with the need of modern times for network security.

  Unfortunately, there is no functionality you describe by saying to DAQmx.  Currently, this type of control is limited to deploying applications to the target of RT.  While the VISA is used for some parts of the DAQmx interaction, these function calls are not documented.  Someone else on the forums may be able to help if they tried to implement something like this in the past.

  Good luck!

• How to synchronize a DSA Board (4496) with several S-series (6143) tips for PXI?

  I need to set up a data system that will require the measure to phase for accelerometers-locking and dynamic deformation signals.  How to synchronize my PXI-4496 Council with my PXI - 6143 s?

  I forgot that some DSA properties does not directly on the devices of the series S I have been able to find an article in the knowledge base that has addressed your specific issue.

  Synchronization Dynamic Signal Acquisition (DSA) with NOR-DAQmx products, this includes an example program synchronization a DSA device and MIO device to sample at the same pace.

• Does anyone have a pinout for the UMI OR AKD Drive Cable?

  I make a motion controller with an NI 7350 card with evasion NI UMI-7774.  I connect to the UMI-7774 to a drive Kollmorgan AKD with UMI OR AKD drive cable.  This cable has a terminal of 20 pin block which I believe includes the home and limit switch signals, but I don't have a pinout of the UMI to AKD drive cable to verify this.  Anyone know where I can get this pinout?

  Thank you

  Chris

  Hi Chris,

  Can be found on page 8 of the manual of getting started with the NI 7340/7350 and AKD Servo Drives Motors controllers the pinout of the connector terminal screws 20 pins of the UMI to AKD drive cable. Please do not hesitate to let us know if you have any other questions or is not what you are looking for.

  Thank you

• Example DDK for PXI-6225

  Hello, I am trying to get the DDK AI working for a PXI-6225 card examples and still receive an output value of 10.599597. I HAVE 0 (68 pins) short-circuited for AI 8 (34 pin) that should lead to a value of 0.0 VDC. I also tried to connect a battery of 9V to terminals and stilll get the 10.599597 value. I know that the Council works because I see all the correct values in the measurement and Automation Explorer. I have already programmed a PXI-6511 and PXI - 6513 PXI - 6704 Council using the DDK examples so I'm quite familiar with the DDK sample Setup, but I can not get this example to work, no matter what I do. Help, please!

  Hi computer guy.

  What example DDK are you using?  Make sure you remove the call to adcReset() because it is only applicable to 625 x materials.  Additionally, make sure that convert it output polarity (selected by aiPersonalize()) and the gain setting and match of research (see ai.h and scale.h) scale factor values you are going for.

  I've also posted a few specific tips 6225 in this thread.

  I hope this helps.

• Star trigger for pxi REPOST 1031 DC - obsolete

  Hello colleagues LV coders.

  I've looked everywhere and can't find the answer to the following question: How can I access a trigger in Star in a PXI 1031 DC chassis?  I know this must be through SLOT2.

  I currently have a micro controller PXI - 8102 SLOT1, an arbitrary generator (AWG) pxi-5422 the SLOT2 and a PXI-7954r FPGA with a digitizer 5761 nor in SLOT4.  I know that activitate the outbreak in Star, a "Timing and synchronization' card must be in the SLOT2.  Is it possible that I can use either the microntroller in SLOT1 or the Working Group in the SLOT2 for access to the relaxation of Star?  I think that the microcontroller will probably be able to reach, but what about the Working Group?

  Follow-up on issues is as follows: suppose that I am able to implement this Star trigger correctly, once the working group receives the signal to send its chirp 10usec by having the Star trigger go HIGH, is there a way of simultaneously to adjust the line of PFI0 HIGH in the Working Group and a time that the 10usec is completely sent to set the PFI0 on the BASS line in the generator of signals for usec then 90? This could be repeated indefinitely and the PFI0 line is used to control a switch via a cable.  In addition, this PFI0 of the GTS line will always be equal to "output mode".

  Thanks in advance a ton.  If I found the answer elsewhere, I'll make sure to update here.

  -Daniel

  Repost tothis forum.

• External clock for PXI-6143

  Hello

  I'm trying to configure the PXI-6143 to use an external clock exported from a generator of arbitrary signals (PXI-5412). I followed the code example (Fgen DAQmx Synchronization.vi) and use one of the RTSI trigger for the export of the clock line, but could not make it work. When I run the attached code, it returned an error not saying not enough samples were taken by the task to HAVE it, but samples are returned correctly if I left PXI-6143 use its internal clock. Could someone point out what's not in this code, please?

  Thank you!!

  I think that I finally understand what has gone wrong...

  I did not indicate the event marker by the niFgen property node. Once I put in, the code works.

  Thanks for the one who never stopped!

• Can I connect a link more MXI for PXI-1033 card in order to work with it

  Ladies and gentlemen,

  Tell me please that I can plug a card of MXI link more in the PXI-1033 chassis in order to work with it.

  In other words, I don't use the built-in controller for MXI and want to work with the NI PXI-8366 MXI-Express and PXI-1033.

  Thank you.

  The answer to your question is no. The question that must be taken into consideration is the type of housing, we have access to on the PXI-1033. To use a PXI MXI card for control purposes in a PXI system, we need to use the card in a slot of system controller (denoted by a triangle around the number of slots on the chassis). With the 1033 however, we have no access to slots control. Because of the connection of controller MXI incorporated, we only have access to a calendar/trigger and devices slots.

  Is there a particular reason you don't want to use on the 1033 MXI connection, or you just want to avoid having to change the connection to another computer?  Single MXI cards which would depend on the space available on the PXI-1033 would be something along the lines of the 8367 and 8367, who are used to the Garland of a separate chassis.

• How to read the analog inputs of one Board of R for (PXI-7851R) series

  You can guide me please with the steps for reading of the analog inputs of a series a. card I use as the target fpga PXI-7851R.

  Have you looked at the examples provided with LabVIEW? There are examples showing how to read the analog inputs.

• Changes in the driver vi using the Simulation Interface Toolkit (SIT) for PXI get do not appear.

  Hello

  I use Simulation Interface Toolkit to target a controller built in Simulink on a PXI target. I used the SIT connection manager to generate the driver screws I had to make some changes in the screw driver specifically Read.vi IO. I made the changes and the entire application runs without error. But the changes are not getting in the functioning of the application, essentially when I load the thing on PXI and run it, it contains exactly as it was before behaiving I made these changes. Some how the changes I make to the Read.vi of e/s are not begin day somewhere in the top vi driver.

  Could someone help me with this please.

  Eliane.

  Hi Justin_P,

  Thank you very much for the reply. Solved the problem. What you're saying, that's certainly true, but I do not use the project.

  The problem was that whenever it makes a change one driver that saw VI top-level driver must be opened and saved again. This opening and registration links the pilot with new changed correctly VI and then everything works fine.

  Thanks again.

  Eliane.

• Video output for PXI embedded real-time?

  I plan to buy a controller PXI real-time Embedded for security monitoring.

  Is it possible to use the video output of a controller PXI running RTOS to display a LabVIEW RT application messages? According to the literature, it seems that the use of the video output is more possible for Controllers PXI running Windows XP.

  Is there a specific application with LabVIEW RT?

  Thanx.

  H.L.

  Well, it works using the IMAQ RT video Out VI: images are displayed properly via the video output of the RTOS PXI controller running.

  Thanx.