PIX 515 and software version 6.3 (4)

We have a PIX 515 (not 515E). Currently, we are running software version 6.2 (2). I was wondering if we can improve the software to version 6.3 (3) or 6.3 (4), or do we need to replace the hardware with PIX 515E?

Also what should I do on my current PDM version 2.0 (2) if it is possible to upgrade the PIX to a 6.3 version?

Thank you.

You can run on the Pix515 6.34. It takes at least 16 MB of flash and 32 MB of RAM.

If you use PDM, you will need to be updated also.

Josh

Tags: Cisco Security

Similar Questions

  • PIX 515 limited software technical spec

    I couldn't find a complete tech

    specifications of the restricted part of the software on the PIX-515-R-DMZ-BUN, which is this chassis seem to bear no x interfaces, y amount of RAM and Z no users inside. X = 3, Y = 32 meg, which is Z and are there restrictions more and more of this?

    Rgds

    Martyn Beck

    The only chassis PIX that has limitations of the user is the 501 PIX which comes with a 10, 50 or unlimited user license. The 515 has not any restrictions on the number of internal users that this number is rather arbitrary. Instead, we use the throughput and simultaneous connections that are roughly 190 MB of throughput and 130 000 simultaneous connections. Also the license restricted on the 515 does not failover of any kind.

    Here is a link to 515E data sheets:

    http://www.Cisco.com/en/us/products/HW/vpndevc/ps2030/products_data_sheet09186a0080091b15.html

    I hope this helps.

    Scott

  • PIX 515 and VAC + card

    Hello

    I just installed a map VAC + in our pix 515.

    I can check if the card is installed and working properly.

    "sh worm" gives no information if the card is installed.

    Greatings Marc

    Do a 'show' version and 'see the crypto engine check.

    See Q & A map VAC:

    http://www.Cisco.com/en/us/customer/products/HW/vpndevc/ps2030/products_qanda_item09186a0080148723.shtml

    sincerely

    Patrick

  • MM, pix 515 and mac filtering

    I have an application called MeetingMaker, located at the back of my pix 515 that is used off site by 5 users. Since accessing this program on the internet, and users can have dynamic addresses, it is possible to filter by mac address somehow to allow access through the firewall to the app? Thank you.

    MAC addresses not browse the limits of layer 3. In others, your MAC address of clients cannot be seen or known once the traffic passes through the default router for that subnet. So the answer to your question is 'no '.

    You can use AAA to handle this. How your clients connect to the server? (port/application)? If its HTTP/S, the Pix can check this name of user and password before allowing access. If it is a part on request/port, you can still use authentication by requiring them to connect to the web server out there first. This will cause the Pix to authenticate by using the challenge of browser, and the Pix can be configured to allow connections to the hosts authentiated.

  • Cisco Pix 515 with ios version 7.01 do not install ASDM

    Hi all

    I have a pic 515 (not the 515E). And I tried to go to 7.21 only when I do that the Pix is unable to settle the version running a lower version 7.01.

    The pix has 64 MB of Ram and 16 MB Flash. (requirements minimum cisco gives.)

    But when I want to install ASDM version 5.01 the pix said there is not enough space.

    Access t... ftp://10.10.199.101/asdm-501.bin!

    % Error copy tftp://10.10.199.101/asdm-501.bin (lack of space on the device)

    What is the solution of the EEG of the ASDM on the pix. upgrade memory or flash memory upgrade?

    Version 6 works with PDM, I tested only I want to use the version 7.

    make a mem sho and sho flash order, under the mem sho, you should see how much you have, also, I run the 7.21 and asdm 5.1, here's my result. You can do a simple deletion? Back upward first if you are leary... but when installing 7.x, I thought he did it for you...

    SEE THE MEM:

    Free memory: 36448176 bytes (54%)

    Memory used: 30660688 bytes (46%)

    ------------- ----------------

    Total memory: 67108864 bytes (100%)

    SEE THE FLASH:

    Directory of flash: /.

    1810 downgrade.cfg

    5386296.bin

    5958324 pdm (may vary)

    > mike elliott

  • How to open a port and limit the range of addresses that use it on PIX 515?

    I have a Pix 515 v6.3 and a new piece of software that I'm getting soon need aura 5080 open port for incoming & outgoing HTTP traffic. The server will be in my DMZ to 10.0.0.1

    I would like to restrict inbound access to this port so that it can be used in 4 specific IP adderess foreign xxx.xxx.xxx.24 through xxx.xxx.xxx.27 and also, if possible, limit the outbound destination using this port to a single specific foreign IP address xxx.xxx.xxx.30.

    Could you please tell me the best way to do it.

    Thank you in advance for a relative novice to PIX.

    PIX (config) # access list acl-outside permit tcp host xxx.xxx.xxx.24 host MyWWWPublicIP eq 5080

    PIX (config) # access list acl-outside permit tcp host xxx.xxx.xxx.25 host MyWWWPublicIP eq 5080

    PIX (config) # access list acl-outside permit tcp host MyWWWPublicIP eq xxx.xxx.xxx.26 host 5080

    PIX (config) # access list acl-outside permit tcp host MyWWWPublicIP eq xxx.xxx.xxx.27 host 5080

    PIX (config) # access - group acl-outside in interface outside

    PIX (config) # access list acl - dmx permit tcp host 10.0.0.1 xxx.xxx.xxx.30 eq 5080

    PIX (config) # access - group acl - dmz dmz interface

    static (inside, outside) MyWWWPublicIP 10.0.0.1 netmask 255.255.255.255 0 0

    See also:

    PIX 500 series firewall

    http://www.Cisco.com/pcgi-bin/support/browse/psp_view.pl?p=hardware:PIX & s = Software_Configuration

    Configuration of the PIX Firewall with access to the Mail Server on the DMZ network

    http://www.Cisco.com/en/us/products/HW/vpndevc/ps2030/products_configuration_example09186a008015efa9.shtml

    sincerely

    Patrick

  • This version of Cisco Adaptive Security Appliance Software Version 9.6 (1) 5 is affected by Cisco Adaptive Security Appliance SNMP Remote Code execution vulnerability and Cisco Adaptive Security Appliance CLI Remote Code execution vulnerability of

    This version of Cisco Adaptive Security Appliance Software Version 9.6 (1) 5 is affected by Cisco Adaptive Security Appliance SNMP Remote Code execution vulnerability and Cisco Adaptive Security Appliance CLI Remote Code execution vulnerability of

    Hi vrian_colaba,

    You can take a look at cisco's Advisory here:

    https://Tools.Cisco.com/Security/Center/content/CiscoSecurityAdvisory/CI...

    Fixed versions

    Cisco ASA Major Release  First version fixed
    7.2 Affected; migrate to 9.1.7(9) or later
    8.0 Affected; migrate to 9.1.7(9) or later
    8.1 Affected; migrate to 9.1.7(9) or later
    8.2 Affected; migrate to 9.1.7(9) or later
    8.3 Affected; migrate to 9.1.7(9) or later
    8.4 Affected; migrate to 9.1.7(9) or later
    8.5 Affected; migrate to 9.1.7(9) or later
    8.6 Affected; migrate to 9.1.7(9) or later
    8.7 Affected; migrate to 9.1.7(9) or later
    9.0 9.0.4 (40)
    9.1 9.1.7(9)
    9.2 9.2.4 (14)
    9.3 9.3.3 (10)
    9.4 9.4.3(8) ETA 26/08/2016
    9.5 9.5 (3) ETA 30/08/2016
    9.6 (DFT) 9.6.1 (11) / 6.0.1(2) FTD
    9.6 (ASA) 9.6.2

    5 9.6 (1) is not part of the fixed versions, this means that is assigned for the SNMP Remote Code execution vulnerability.

    Cisco Adaptive Security Appliance CLI Remote Code vulnerability to run you can also take a look at cisco's Advisory here:

    https://Tools.Cisco.com/Security/Center/content/CiscoSecurityAdvisory/CI...

    Fixed versions

    The following table shows the first software versions that include fixes for this vulnerability (9.6 is not affected)

    Cisco ASA Major Release First version fixed
    7.2 Affected, migrate to 8.4 (3) or later
    8.0 Affected, migrate to 8.4 (3) or later
    8.1 Affected, migrate to 8.4 (3) or later
    8.2 Affected, migrate to 8.4 (3) or later
    8.3 Affected, migrate to 8.4 (3) or later
    8.4 8.4 (3)
    8.5 Affected, migrate to 9.0 (1) or later version
    8.6 Affected, migrate to 9.0 (1) or later version
    8.7 Affected, migrate to 9.0 (1) or later version
    9.0 9.0 (1)
    9.1 Not affected
    9.2 Not affected
    9.3 Not affected
    9.4 Not affected
    9.5 Not affected
    9.6 Not affected

    Hope this info helps!

    Note If you help!

    -JP-

  • What is the difference between the "Software Version" and "Version of the platform?

    I posted in this forum, because there is a maximum activity in this forum. Sorry, if this is not a good place to post this kind of question.

    What is the difference between the "Software Version" and "Version of the platform" of any blackberry device?

    My camera's curve 8900 and I can see in the menu About his version of software is 4.6.1.231 and the version of the platform is 4.2.0.108. What are these 2 versions for?

    Probably the best posted in the software section of the device, but is not serious.

    Version of the software/App - indicates the version of your applications (address book, browser, calendar, etc.).
    Version of the platform - indicates your version of system software (Java based software, radio code, etc.).

  • can you have a version of CS and several version of the software installed for example Lightroom CC both?

    can you have a version of CS and several version of the software installed for example Lightroom CC both?

    Yes, you can have multiple versions installed.

    Please see this link:

    Download previous versions of Adobe Creative applications-

    Download previous versions of Cloud Creative applications

    You can have both CC and CS6 installed through creative cloud. You can also leave the old purchased software installed.

  • PDM with PIX 515 does not work

    I just upgraded our PIX 515 of 6.1 to 6.2. I also added support FOR and loaded the version 2.1 of the PDM. I am trying to browse the MDP, but I can't. What Miss me?

    Hello

    have you added the following lines to your config file and have you used HTTPS to access the pix (http is not taken in charge, only https)?

    Enable http server

    http A.B.C.D 255.255.255.255 inside

    A.B.C.D is the ip address of the host from which you are trying to reach the pix with the pdm.

    If you're still having problems after the addition of these two lines, you might have a look at this page:

    http://www.Cisco.com/warp/customer/110/pdm_http404.shtml

    Kind regards

    Tom

  • PIX - 515 does not identify Tokenring Interfacecard

    Hello

    I installed a PIX-1 TR interface in the PIX 515. Start ok, 'answer' no configuration. SH LVE and sho int etc. presents only the build Ethernet0 and Eth1 but no interface tokenring.

    HS release looks like as follows.

    Thanks Ruedi

    pixfirewall # sh ver

    Cisco PIX Firewall Version 6.2 (2)

    Cisco PIX Device Manager Version 2.0 (2)

    Updated Saturday, June 7 02 17:49 by Manu

    pixfirewall until 10 mins dry 14

    Material: PIX - 515, 32 MB RAM, Pentium 200 MHz processor

    I28F640J5 @ 0 x 300 Flash, 16 MB

    BIOS Flash AT29C257 @ 0xfffd8000, 32 KB

    0: ethernet0: the address is 0003.6bf6.a8a9, irq 11

    1: ethernet1: the address is 0003.6bf6.a8aa, irq 10

    Features licensed:

    Failover: disabled

    VPN - A: enabled

    VPN-3DES: disabled

    Maximum Interfaces: 3

    Cut - through Proxy: enabled

    Guardians: enabled

    URL filtering: enabled

    Internal hosts: unlimited

    Throughput: unlimited

    Peer IKE: unlimited

    Serial number: 405341167 (0x182903ef)

    Activation key running: xxxxxxxxx

    Modified configuration of enable_15 to 13:11:47.490 UTC Tuesday, December 23, 2003

    pixfirewall #.

    Hello

    Token-Ring is no longer supported, I think since version 6.0.

  • PIX 515 DMZ problem

    Hello

    We have some difficulty in moving traffic in and out of a Cisco PIx 515 firewall. We use it with two demilitarized. The first DMZ has a mail in her Server (before end mail server) that communicates with a different mail server (back end mail server) inside, it is called DMZ1. The second DMZ (DMZ2) has some users who are expected to pass through the firewall to the outside and use the internet and must have access to the e-mail DMZ1 server. Inside users must be able to use the Internet and can access DMZ1. Here's the important part of our Setup.

    What we were doing, we can correctly access from inside, inside users to access internet permit to join the DMZ1 e-mail server and the mail in DMZ1 server the inside. Our problem is that we are unable to browse the internet on the DMZ1 Messaging server if we put DMZ1 as gateway ip address on that server and the address ip of the DNS of the ISP is propely located on the same machine. Also, we could not do DMZ2 users browse the internet, although we allowed the www Protocol in the fromOut access list. One last question, can we do the DMZ2 a DHCP server on the interface on the PIX and do distribute ip addresses to users on that subnet only? Thanks for any help in advance.

    6.3 (3) version PIX

    interface ethernet0 car

    Auto interface ethernet1

    Auto interface ethernet2

    Auto ethernet3 interface

    !

    ethernet0 nameif outside security0

    nameif ethernet1 inside the security100

    nameif ethernet2 dmz1 security50

    nameif ethernet3 dmz2 security40

    !

    fixup protocol dns-length maximum 512

    fixup protocol ftp 21

    fixup protocol h323 h225 1720

    fixup protocol h323 ras 1718-1719

    fixup protocol http 80

    fixup protocol rsh 514

    fixup protocol rtsp 554

    fixup protocol sip 5060

    fixup protocol sip udp 5060

    fixup protocol 2000 skinny

    fixup protocol smtp 25

    fixup protocol sqlnet 1521

    fixup protocol tftp 69

    !

    names of

    !

    IP outside X.Y.Z.163 255.255.255.248

    IP address inside 192.168.0.9 255.255.255.0

    dmz1 192.168.10.1 IP address 255.255.255.0

    IP address dmz2 192.168.20.1 255.255.255.0

    !

    fromOut list of access permit icmp any host X.Y.Z.162 source-quench

    fromOut list of access permit icmp any host X.Y.Z.162 echo-reply

    fromOut list of access permit icmp any unreachable host X.Y.Z.162

    fromOut list of access permit icmp any host X.Y.Z.162 time limit

    fromOut list access permit tcp any host X.Y.Z.162 EQ field

    fromOut list access permit tcp any host X.Y.Z.162 eq telnet

    fromOut list access permit tcp any host X.Y.Z.162 eq smtp

    fromOut list access permit tcp any host X.Y.Z.162 eq www

    !

    fromDMZ1 list of access permit tcp host 192.168.10.2 192.168.0.0 255.255.255.0

    fromDMZ1 list of allowed access host ip 192.168.10.2 192.168.0.0 255.255.255.0

    !

    fromDMZ2 list of access allowed tcp 192.168.20.0 255.255.255.0 192.168.10.0 255.255.255.0

    !

    pager lines 24

    !

    Outside 1500 MTU

    Within 1500 MTU

    dmz1 MTU 1500

    dmz2 MTU 1500

    !

    Global (outside) 1 X.Y.Z.164 netmask 255.255.255.248

    Global (outside) 2 X.Y.Z.165 netmask 255.255.255.248

    NAT (inside) 1 192.168.0.0 255.255.255.0 0 0

    NAT (dmz1) 1 192.168.10.2 255.255.255.255 0 0

    NAT (dmz2) 2 192.168.20.0 255.255.255.0 0 0

    static (inside, dmz1) 192.168.0.0 192.168.0.0 netmask 255.255.255.0 0 0

    static (dmz2, dmz1) 192.168.0.0 192.168.0.0 netmask 255.255.255.0 0 0

    static (dmz1, external) X.Y.Z.162 192.168.10.2 netmask 255.255.255.255 0 0

    !

    Access-group fromOut in interface outside

    Access-group fromDMZ1 in interface dmz1

    Access-group fromDMZ2 in the dmz2 interface

    Route outside 0.0.0.0 0.0.0.0 X.Y.Z.161 1

    Hi jamil,.

    There is a sentence on the URL I sent you, you can now activate dhcp option within the interface. Just check this...

    REDA

  • termination of VPN client 4.0 on pix 515

    I am trying to connect the cisco 4.0 vpn client to a worm of pix 515 6.1 and receive as a result of errors that I guess are the related hashing algorithm but am not sure. Only DES is not enabled 3DES. Config output Cisco post interprets but apparently no error in config.

    Journal of VPN client:

    Cisco Systems VPN Client Version 4.0 (Rel)

    Copyright (C) 1998-2003 Cisco Systems, Inc. All rights reserved.

    Customer type: Windows, Windows NT

    Running: 5.0.2195

    1 10:58:34.890 25/09/03 Sev = Info/4 CM / 0 x 63100002

    Start the login process

    2 10:58:34.906 25/09/03 Sev = Info/4 CVPND/0xE3400001

    Microsoft's IPSec Policy Agent service stopped successfully

    3 10:58:34.906 25/09/03 Sev = Info/4 CM / 0 x 63100004

    Establish a connection using Ethernet

    4 10:58:34.906 25/09/03 Sev = Info/4 CM / 0 x 63100024

    Attempt to connect with the server "x.x.x.226".

    5 10:58:35.953 25/09/03 Sev = Info/6 IKE/0x6300003B

    Attempts to establish a connection with x.x.x.226.

    6 10:58:36.000 25/09/03 Sev = Info/4 IKE / 0 x 63000013

    SEND to > ISAKMP OAK AG (SA, KE, NO, ID, VID (Xauth), VID (dpd), VID (Nat - T), VID (Frag), VID (Unity)) at x.x.x.226

    7 10:58:36.000 25/09/03 Sev = Info/4 IPSEC / 0 x 63700008

    IPSec driver started successfully

    8 10:58:36.000 25/09/03 Sev = Info/4 IPSEC / 0 x 63700014

    Remove all keys

    9 10:58:41.093 25/09/03 Sev = Info/4 IKE / 0 x 63000021

    Retransmit the last package!

    10 10:58:41.093 25/09/03 Sev = Info/4 IKE / 0 x 63000013

    SEND to > ISAKMP OAK AG (Retransmission) to x.x.x.226

    11 10:58:46.093 25/09/03 Sev = Info/4 IKE / 0 x 63000021

    Retransmit the last package!

    12 10:58:46.093 25/09/03 Sev = Info/4 IKE / 0 x 63000013

    SEND to > ISAKMP OAK AG (Retransmission) to x.x.x.226

    13 10:58:51.093 25/09/03 Sev = Info/4 IKE / 0 x 63000021

    Retransmit the last package!

    14 10:58:51.093 25/09/03 Sev = Info/4 IKE / 0 x 63000013

    SEND to > ISAKMP OAK AG (Retransmission) to x.x.x.226

    15 10:58:56.093 25/09/03 Sev = Info/4 IKE / 0 x 63000017

    Marking of IKE SA delete (I_Cookie = 20FC277498A5D2DC R_Cookie = 0000000000000000) reason = DEL_REASON_PEER_NOT_RESPONDING

    16 10:58:56.593 25/09/03 Sev = Info/4 IKE/0x6300004A

    IKE negotiation to throw HIS (I_Cookie = 20FC277498A5D2DC R_Cookie = 0000000000000000) reason = DEL_REASON_PEER_NOT_RESPONDING

    17 10:58:56.593 25/09/03 Sev = Info/4 CM / 0 x 63100014

    Could not establish the Phase 1 SA with the server 'x.x.x.226' due to the 'DEL_REASON_PEER_NOT_RESPONDING '.

    18 10:58:56.593 25/09/03 Sev = Info/5 CM / 0 x 63100025

    Initializing CVPNDrv

    19 10:58:56.593 25/09/03 Sev = Info/4 IKE / 0 x 63000001

    Signal received IKE to complete the VPN connection

    20 10:58:56.625 25/09/03 Sev = critique/1 CVPND/0xE3400001

    Service Microsoft's IPSec Policy Agent started successfully

    21 10:58:57.093 25/09/03 Sev = Info/4 IPSEC / 0 x 63700014

    Remove all keys

    22 10:58:57.093 25/09/03 Sev = Info/4 IPSEC / 0 x 63700014

    Remove all keys

    23 10:58:57.093 25/09/03 Sev = Info/4 IPSEC / 0 x 63700014

    Remove all keys

    24 10:58:57.093 25/09/03 Sev = Info/4 IPSEC/0x6370000A

    IPSec driver successfully stopped

    Journal of Pix:

    crypto_isakmp_process_block: CBC x.x.x.194, dest x.x.x.226

    Peer VPN: ISAKMP: approved new addition: ip:x.x.x.194 Total VPN peer: 1

    Peer VPN: ISAKMP: ip:x.x.x.194 Ref cnt is incremented to peers: 1 Total VPN EEP

    RS: 1

    Exchange OAK_AG

    ISAKMP (0): treatment ITS payload. Message ID = 0

    ISAKMP (0): audit ISAKMP transform 1 against the policy of priority 1

    ISAKMP: encryption... What? 7?

    ISAKMP: hash SHA

    ISAKMP: default group 2

    ISAKMP: preshared extended auth

    ISAKMP: type of life in seconds

    ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b

    ISAKMP: attribute 3584

    ISAKMP (0): atts are not acceptable. Next payload is 3

    ISAKMP (0): audit ISAKMP transform against the policy of priority 1 2

    ISAKMP: encryption... What? 7?

    ISAKMP: MD5 hash

    ISAKMP: default group 2

    ISAKMP: preshared extended auth

    ISAKMP: type of life in seconds

    ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b

    ISAKMP: attribute 3584

    ISAKMP (0): atts are not acceptable. Next payload is 3

    ISAKMP (0): audit ISAKMP transform 3 against the policy of priority 1

    ISAKMP: encryption... What? 7?

    ISAKMP: hash SHA

    ISAKMP: default group 2

    ISAKMP: preshared auth

    ISAKMP: type of life in seconds

    ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b

    ISAKMP: attribute 3584

    ISAKMP (0): atts are not acceptable. Next payload is 3

    ISAKMP (0): audit ISAKMP transform 4 against the policy of priority 1

    ISAKMP: encryption... What? 7?

    ISAKMP: MD5 hash

    ISAKMP: default group 2

    ISAKMP: preshared auth

    ISAKMP: type of life in seconds

    ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b

    ISAKMP: attribute 3584

    ISAKMP (0): atts are not acceptable. Next payload is 3

    ISAKMP (0): audit ISAKMP transform 5 against the policy of priority 1

    ISAKMP: encryption... What? 7?

    ISAKMP: hash SHA

    ISAKMP: default group 2

    ISAKMP: preshared extended auth

    ISAKMP: type of life in seconds

    ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b

    ISAKMP: attribute 3584

    ISAKMP (0): atts are not acceptable. Next payload is 3

    ISAKMP (0): audit ISAKMP transform 6 against the policy of priority 1

    ISAKMP: encryption... What? 7?

    ISAKMP: MD5 hash

    ISAKMP: default group 2

    ISAKMP: preshared extended auth

    ISAKMP: type of life in seconds

    ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b

    ISAKMP: attribute 3584

    ISAKMP (0): atts are not acceptable. Next payload is 3

    ISAKMP (0): audit ISAKMP transform 7 against the policy of priority 1

    ISAKMP: encryption... What? 7?

    ISAKMP: hash SHA

    ISAKMP: default group 2

    ISAKMP: preshared auth

    ISAKMP: type of life in seconds

    ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b

    ISAKMP: attribute 3584

    ISAKMP (0): atts are not acceptable. Next payload is 3

    ISAKMP (0): audit ISAKMP transform 8 against the policy of priority 1

    ISAKMP: encryption... What? 7?

    ISAKMP: MD5 hash

    ISAKMP: default group 2

    ISAKMP: preshared auth

    ISAKMP: type of life in seconds

    ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b

    ISAKMP: attribute 3584

    ISAKMP (0): atts are not acceptable. Next payload is 3

    ISAKMP (0): audit ISAKMP transform 9 against the policy of priority 1

    ISAKMP: 3DES-CBC encryption

    ISAKMP: hash SHA

    ISAKMP: default group 2

    ISAKMP: preshared extended auth

    ISAKMP: type of life in seconds

    ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4

    crypto_isakmp_process_block: CBC x.x.x.194, dest x.x.x.226

    Peer VPN: ISAKMP: ip:x.x.x.194 Ref cnt is incremented to peers: 2 Total VPN EEP

    RS: 1

    Peer VPN: ISAKMP: ip:x.x.x.194 Ref cnt decremented to peers: 1 Total VPN EEP

    RS: 1

    crypto_isakmp_process_block: CBC x.x.x.194, dest x.x.x.226

    Peer VPN: ISAKMP: ip:x.x.x.194 Ref cnt is incremented to peers: 2 Total VPN EEP

    RS: 1

    Peer VPN: ISAKMP: ip:x.x.x.194 Ref cnt decremented to peers: 1 Total VPN EEP

    RS: 1

    ISAKMP (0): retransmission of phase 1...

    ISAKMP (0): retransmission of phase 1...

    ISAKMP (0): delete SA: src x.x.x.194 dst x.x.x.226

    ISADB: Reaper checking HIS 0x80db91c8, id_conn = 0 DELETE IT!

    Peer VPN: ISAKMP: ip:x.x.x.194 Ref cnt decremented to peers: 0 Total of VPN EEP

    RS: 1

    Peer VPN: ISAKMP: deleted peer: ip:x.x.x.194 VPN peer Total: 0

    ISAKMP: Remove the peer node for x.x.x.194

    Thanks for any help

    Hello

    Pix isakmp policy should have DES, MD5, and group 2 for the 4.x to connect Cisco VPN client, these are proposals that the client sends to the server...

    http://www.Cisco.com/univercd/CC/TD/doc/product/VPN/client/rel4_0/admin_gd/vcach6.htm#1157757

    This link will show you IKE proposals be configured on the PIX (VPN server)

    Arthur

  • PIX 515 adding a second DMZ

    Hello

    This is the specification of our PIX:

    Cisco PIX Firewall Version 6.2 (2)

    Cisco PIX Device Manager Version 2.0 (2)

    Updated Saturday, June 7 02 17:49 by Manu

    Firewall of the hours - days.

    Material: PIX - 515, 32 MB RAM, Pentium 200 MHz processor

    I28F640J5 @ 0 x 300 Flash, 16 MB

    BIOS Flash AT29C257 @ 0xfffd8000, 32 KB

    0: ethernet0: the address is 0003.6bf6.74a2, irq 11

    1: ethernet1: the address is 0003.6bf6.74a3, irq 10

    2: ethernet2: the address is 00a0.c944.395b, irq 9

    Features licensed:

    Failover: disabled

    VPN - A: enabled

    VPN-3DES: enabled

    Maximum Interfaces: 3

    Cut - through Proxy: enabled

    Guardians: enabled

    URL filtering: enabled

    Internal hosts: unlimited

    Throughput: unlimited

    Peer IKE: unlimited

    Is it possible to add a second DMZ simply by adding another network card to the system? If this is not the case, what I have to do to get a second DMZ?

    Kind regards

    Alan

    You have already 3 interfaces, and your license only allows 3 (that you run limited license). Read the line of your worm above show: maximum Interfaces: 3

    You must update your Unrestricted license, then you can have up to 6 interfaces.

    It will be useful.

    Steve

  • PIX 515 6.1 (1) crashes every night

    We have a PIX 515 E Firewall (failover) with a simple configuration to allow web traffic only from inside. PIX with three interfaces ethernet and the DMZ is rarely used for specific needs. A www server is hosted with authentication through aaa for incoming users inside.

    For the last week, PIX crashes end each evening. No traffic doesn't cross the pix and we cannot ping all devices of pix as well. There are a lot of "no buffers" counts seen in all the PIX interfaces. The CPU usage is about 21%.

    Can anyone help to determine if this could be a hardware problem?

    Best regards, Murali

    Hi Murali,

    I'm not aware of any problem with the hardware, but there could be a software bug. I suggest that you open a case with cisco tac.

    or you can upgrade to 6.1.4 which has fix for most of the bugs.

    Thank you

    Syed

Maybe you are looking for

  • After loading Windows - crashes BSOD on Portege A200

    Portege A200 Windows XP; Before windows has finished loading a blue screen appears and the machine stops. Prior to that, the machine was intermittenlty off without apparent reason. The last thing I did before this happened has been updated to IE 7. R

  • DeskJet 3050: Lack of ink in the ink cartridges

    After having so many problems when trying to print 4 x 6 photos, I found that I ran more ink, which seemed to be too early. After this happened to me twice, I bought a new cartridge and open before using it. I was at a loss to explain to myself as to

  • Recovery of Windows 7 Ultimate

    Hello! On March 24, I decided to upgrade to Windows 10, via Internet, but after that, it was difficult to find my files and so I canceled and to restore the computer to Windows 7 Ultimate. But something strange happens since then. When I opened my la

  • Import addresses MAC of SSCM at ISE to boot PXE via API

    During PXE starts the process in a network with ISE (2.1) and 802. 1 x activated, a new customer has access to the network through MAB in ISE. Instead of register all MAC addresses manually (or via .csv file) at ISE, we look for a way to import addre

  • Smartphones BBM blackBerry problem please help me.

    I am updating my bbm to 7 then when I click on "combining bbm with your blackberry id" appears it stuck there., I waited for hours but nothing happens, before when I use it, but when I updated it stuck there. What should I do so that I can use my bbm