MM, pix 515 and mac filtering

Similar Questions

• iPad Air2, Wi - Fi and MAC filtering

  Two other iPads in the House and my iPad Air2 keep disconnecting my wireless router when I turn MAC filtering AND broadcast THAT SSID is disabled. I can't even manually connect to the router, but when I turn one of these functions, or both, the device will automatically reconnect.  I have a router Linksys WRT of Dual-band 1900AC. I have not had this problem with my previous NetGear router. Does anyone know of a solution?

  Before ask you, yes the MAC addresses of my devices are entered into the router. Also, I realize that MAC filtering is not a security measure. It is not my purpose for its use.

  Thank you!

  Can you give us more details?

  What happens when you try to manually connect?

  I'm afraid to say "cannot connect manually" isn't much for us to go. You have "ask to join networks" enabled?

  Have you tried to install the app from Linksys? I know this is to configure the router, but maybe it will help you to establish a compatible connection.

• E4200: comments of networking and MAC filtering

  Hello

  I have my e4200 with active network guest and also MAC filtering installation. Somehow, I've been epxecting MAC filtering to do not apply to the network without comment thread, but it seems to be the case.

  Can someone confirm please if this is the case and if there is a work around?

  beautifulbeatrice wrote:

  It depends on which option you select. There is an option to prevent certain MAC address to connect to the network and an option to allow certain MAC addresses to connect. It depends on what you choose. Please see the link below for more information.

  Furthermore, network comments shouldn't be assigned to Wireless Mac Filter restrictions.

  Setting up wireless MAC filtering to prevent users to connect to the network wirelessly on your L...

  Setting up wireless MAC filtering to permit users to connect to the network on your Linksys Wireless...

  ^ ^ ^ Too bad the guest network is affected by the MAC filter.

• PIX 515 and software version 6.3 (4)

  We have a PIX 515 (not 515E). Currently, we are running software version 6.2 (2). I was wondering if we can improve the software to version 6.3 (3) or 6.3 (4), or do we need to replace the hardware with PIX 515E?

  Also what should I do on my current PDM version 2.0 (2) if it is possible to upgrade the PIX to a 6.3 version?

  Thank you.

  You can run on the Pix515 6.34. It takes at least 16 MB of flash and 32 MB of RAM.

  If you use PDM, you will need to be updated also.

  Josh

• PIX 515 and VAC + card

  Hello

  I just installed a map VAC + in our pix 515.

  I can check if the card is installed and working properly.

  "sh worm" gives no information if the card is installed.

  Greatings Marc

  Do a 'show' version and 'see the crypto engine check.

  See Q & A map VAC:

  http://www.Cisco.com/en/us/customer/products/HW/vpndevc/ps2030/products_qanda_item09186a0080148723.shtml

  sincerely

  Patrick

• Disable broadcast SSID and MAC address turn on filtering on WAG320N

  When disabling SSID broadcast and enabling MAC address filtering on WAG320N, my other laptop wireless disconnected.  And when you try to connect, it connects again.

  You can not hide from intruders.

  The router always sends the tag. The router is immediately detected.

  The SSID is always transferred not encrypted. He is always sent over the association. It is easy to force a re-Association. If there is a single device without wire connected to the access point it takes about a second to learn the SSID.

  Disable the SSID requires your wireless devices to search actively for the network. This means that your laptop will always try to connect to your SSID, as long as it is not connected to another network. As sending requires much more power then listen passively it drains your battery.

  And, in fact, if you are in an internet café anyone can learn your SSID in time where you go on the wireless at the moment where you associate with the network of internet café.

  In addition, it causes many problems with different wireless, as instability or similar cards.

  MAC filtering is still more useless that the MAC address is always part of any wireless transmission and it's always clear. It is extremely easy to pick up the allowed MAC addresses, and it is extremely easy to change the MAC address of a wireless card.

  New: use the real security and forget this nickname of security features.

  What you try to do is a waste of time. Of your time. It will slow down any intruder.

  See also

  http://homecommunity.Cisco.com/T5/wireless-routers/iPad-Wi-Fi-MAC-address-quot-not-a-MAC-address-quo...
  http://homecommunity.Cisco.com/T5/wireless-routers/is-my-router-effectively-secured/m-p/333945#M1752...

• How to open a port and limit the range of addresses that use it on PIX 515?

  I have a Pix 515 v6.3 and a new piece of software that I'm getting soon need aura 5080 open port for incoming & outgoing HTTP traffic. The server will be in my DMZ to 10.0.0.1

  I would like to restrict inbound access to this port so that it can be used in 4 specific IP adderess foreign xxx.xxx.xxx.24 through xxx.xxx.xxx.27 and also, if possible, limit the outbound destination using this port to a single specific foreign IP address xxx.xxx.xxx.30.

  Could you please tell me the best way to do it.

  Thank you in advance for a relative novice to PIX.

  PIX (config) # access list acl-outside permit tcp host xxx.xxx.xxx.24 host MyWWWPublicIP eq 5080

  PIX (config) # access list acl-outside permit tcp host xxx.xxx.xxx.25 host MyWWWPublicIP eq 5080

  PIX (config) # access list acl-outside permit tcp host MyWWWPublicIP eq xxx.xxx.xxx.26 host 5080

  PIX (config) # access list acl-outside permit tcp host MyWWWPublicIP eq xxx.xxx.xxx.27 host 5080

  PIX (config) # access - group acl-outside in interface outside

  PIX (config) # access list acl - dmx permit tcp host 10.0.0.1 xxx.xxx.xxx.30 eq 5080

  PIX (config) # access - group acl - dmz dmz interface

  static (inside, outside) MyWWWPublicIP 10.0.0.1 netmask 255.255.255.255 0 0

  See also:

  PIX 500 series firewall

  http://www.Cisco.com/pcgi-bin/support/browse/psp_view.pl?p=hardware:PIX & s = Software_Configuration

  Configuration of the PIX Firewall with access to the Mail Server on the DMZ network

  http://www.Cisco.com/en/us/products/HW/vpndevc/ps2030/products_configuration_example09186a008015efa9.shtml

  sincerely

  Patrick

• PIX - 515 does not identify Tokenring Interfacecard

  Hello

  I installed a PIX-1 TR interface in the PIX 515. Start ok, 'answer' no configuration. SH LVE and sho int etc. presents only the build Ethernet0 and Eth1 but no interface tokenring.

  HS release looks like as follows.

  Thanks Ruedi

  pixfirewall # sh ver

  Cisco PIX Firewall Version 6.2 (2)

  Cisco PIX Device Manager Version 2.0 (2)

  Updated Saturday, June 7 02 17:49 by Manu

  pixfirewall until 10 mins dry 14

  Material: PIX - 515, 32 MB RAM, Pentium 200 MHz processor

  I28F640J5 @ 0 x 300 Flash, 16 MB

  BIOS Flash AT29C257 @ 0xfffd8000, 32 KB

  0: ethernet0: the address is 0003.6bf6.a8a9, irq 11

  1: ethernet1: the address is 0003.6bf6.a8aa, irq 10

  Features licensed:

  Failover: disabled

  VPN - A: enabled

  VPN-3DES: disabled

  Maximum Interfaces: 3

  Cut - through Proxy: enabled

  Guardians: enabled

  URL filtering: enabled

  Internal hosts: unlimited

  Throughput: unlimited

  Peer IKE: unlimited

  Serial number: 405341167 (0x182903ef)

  Activation key running: xxxxxxxxx

  Modified configuration of enable_15 to 13:11:47.490 UTC Tuesday, December 23, 2003

  pixfirewall #.

  Hello

  Token-Ring is no longer supported, I think since version 6.0.

• PIX 515 adding a second DMZ

  Hello

  This is the specification of our PIX:

  Cisco PIX Firewall Version 6.2 (2)

  Cisco PIX Device Manager Version 2.0 (2)

  Updated Saturday, June 7 02 17:49 by Manu

  Firewall of the hours - days.

  Material: PIX - 515, 32 MB RAM, Pentium 200 MHz processor

  I28F640J5 @ 0 x 300 Flash, 16 MB

  BIOS Flash AT29C257 @ 0xfffd8000, 32 KB

  0: ethernet0: the address is 0003.6bf6.74a2, irq 11

  1: ethernet1: the address is 0003.6bf6.74a3, irq 10

  2: ethernet2: the address is 00a0.c944.395b, irq 9

  Features licensed:

  Failover: disabled

  VPN - A: enabled

  VPN-3DES: enabled

  Maximum Interfaces: 3

  Cut - through Proxy: enabled

  Guardians: enabled

  URL filtering: enabled

  Internal hosts: unlimited

  Throughput: unlimited

  Peer IKE: unlimited

  Is it possible to add a second DMZ simply by adding another network card to the system? If this is not the case, what I have to do to get a second DMZ?

  Kind regards

  Alan

  You have already 3 interfaces, and your license only allows 3 (that you run limited license). Read the line of your worm above show: maximum Interfaces: 3

  You must update your Unrestricted license, then you can have up to 6 interfaces.

  It will be useful.

  Steve

• PIX 515 no traffic on the new IP address don't block

  We have received a new range of ips 213.x.x.x/28 from our ISP. They are routed through our existing entry door 92.x.x.146.

  The problem:
  We can not all traffic to the pix on the new 213.x.x.x/28 range.
  -If we try to ping 213.x.x.61, we get the lifetime exceeded.
  -ISP Gets the same thing of their router.
  -ISP tries ssh and gets no route to host.

  The ISP has ticked then double the Routing and the MAC address of our external interface. They are correct.

  The strange thing is that we cannot see THE log messages about the new range of incoming connection attempts. The Pix is running at the level of the journal 7.

  Does anyone have an idea what could be the problem? or suggestions for debugging the issue?

  Excerpt from config:
  7.0 (7) independent running Pix 515
  outside 92.x.x.146 255.255.255.240
  inside 192.168.101.1 255.255.255.0
  Global 1 interface (outside)
  NAT (inside) 1 0.0.0.0 0.0.0.0
  Route outside 0.0.0.0 0.0.0.0 92.x.x.145 1
  Access-group acl_out in interface outside
  acl_out list extended access permit tcp any host 213.x.x.x eq www
  acl_out list extended access permit tcp any host 213.x.x.x eq ssh
  static (inside, outside) 213.x.x.61 192.168.101.99 netmask 255.255.255.255
  ICMP allow any inaccessible State

  192.168.101.99 is a test with http and ssh linux server

  Any help much appreciated.

  PM

  dsc_tech_1 wrote:
  I have spoken to the ISP and confirmed the MAC address of the outside interface Ethernet0
  
      ISP says
  
      ...we are sending this correctly to your pix, you should see any traffic destined for a 213.x.x.0/28 address hit your interface at 92.x.x.146/32
  
  Yes 217.x.x.81 and 217.x.x.82 are routers owned by our ISP.
  Is there anything else I can ask the ISP in terms of testing/debugging? I've run out of ideas.
  

  If the routers are owned by your ISP, then the fault lies with them. They have a routing loop in their network and that's why packages are not your firewall. You have them shown the traceroute?

  They must focus on the routeurs.81 et.82 to establish why the packets are looped between these 2 routers. Until they fix this packet will never get your firewall.

  Jon

• PIX 501 and THE, 3DES, AES

  For a version newly produced PIX 501,

  (1) are DES, 3DES and AES activation keys all pre-installed?

  (2) how I can find on which of them is pre-installed on my PIX 501?

  (3) when I create a server VPN (on the PIX 501), I see that all three OF THEM, 3DES and AES are available in the drop-down list of the PDM configuration screen. Does that mean my PIX 501 have all three of them (FROM THE, 3DES and AES)? -If the answer is no, assume that only is preinstalled on PIX 501, then why/how can appear in the drop-down list the 3DES and AES?

  Thank you for helping.

  Scott

  Should be integrated already. depends on the way the news is your PIX 501.

  To be sure to log in to the console and type:

  See the version

  See the example output version:

  See the pixfirewall version (config) #.

  Cisco PIX Firewall Version 6.2 (3)

  Cisco PIX Device Manager Version 2.0 (1)

  Updated Thursday April 17 02 21:18 by Manu

  pixdoc515 up to 9 days 3 hours

  Material: PIX - 515, 64 MB RAM, Pentium 200 MHz processor

  I28F640J5 @ 0 x 300 Flash, 16 MB

  BIOS Flash AT29C257 @ 0xfffd8000, 32 KB

  0: ethernet0: the address is 0050.54ff.3772, irq 10

  1: ethernet1: the address is 0050.54ff.3773, irq 7

  2: ethernet2: the address is 00d0.b792.409d, irq 11

  Features licensed:

  Failover: enabled

  VPN - A: enabled

  VPN-3DES: enabled

  Maximum Interfaces: 6

  Cut - through Proxy: enabled

  Guardians: enabled

  URL filtering: enabled

  Internal hosts: unlimited

  Throughput: unlimited

  Peer IKE: unlimited

  Serial number: 480221353 (0x1c9f98a9)

  Activation key running: 0x36df4255 0x246dc5fc 0x39d2ec4d 0x09f6288f

  Modified configuration of enable_15 to 12:15:28.311 UTC Wednesday, may 1, 2002

  pixfirewall (config) #.

  Here, you should see if THE or 3DES, AES encryption is active or not. If you have just SOME so you can use the following link and get for free a new activation key that allows 3DES and AES.

  https://Tools.Cisco.com/swift/licensing/JSP/formGenerator/Pix3DesMsgDisplay.jsp

  sincerely

  Patrick

• D link Dir 803: ADDRESS MAC FILTERING

  Hello
  Am really sorry for questions not related to HP, I really apologize but I know it's the best solution Center. Use the router D - link Dir 803 many people have my password and the theft of my internet so now I want to control by MAC address filtering as well as a few people I want to give them access I will configure their MAC address on my laptop, I think that later even if I give my password without your MAC address on my system you will not have access. I humbly ask for the solution of the master in technology.
  NOTE: MAC ADDRESS FILTERING ON D-LINK DIR 803 (FREE WI - FI.
  Thanks and greetings
  Richperry

  Hello

  You must connect to your router to set up. Please use the following manual #74 page:

  http://www.dlinkmea.com/partner/media/product_item_downloadables/3400-dir-803_A1_Manual_v1.00%28DI%29.PDF

  Note: The MAC filtering isn't a good choice, you can use WPA™ and WPA2™ to improve safety.

  Kind regards.

• Address MAC WUMC710 problems when using MAC filtering

  I recently bought the point WUMC710-HQ AC wireless to connect to my router EA6500.  Generally, the WUMC710 seems to work.  I was able to connect to the router wirelessly on the 5 GHz band and flow EA6500 a NetFlix video with no problems.

  However, there is a major problem that comes makes no logical sense for me:

  When I turn on the wireless MAC address filtering of the EA6500, the WUMC710 does not connect to the EA6500router.

  Yet, I 8 eight other wireless devices on my network which connect very well to the EA6500 when the MAC address filtering is enabled.  Thus, the question seems to outright to WUMC710.

  The address printed on the product shipment to the ends of the box with numbers XX:1 d.

  This address matches the address printed at the bottom of the WUMC710 MAC. (normal)

  My EA6500 router recognizes this MAC address as the correct MAC associated with the WUMC710 (when MAC filtering is enabled).  But as soon as the MAC filtering is turned on, the WUMC710 does not recover to the router. (I checked the MAC address, that I walked into the filter at least a dozen times, and she entered correct - but all my other wireless devices connect OK).

  This is a point that seems strange on the MAC address associated to the WUMC710:

  When I am able to connect to the WUMC710, State--> tab Device illustrated the right address MAC I use to filter.  But when I check the status--> network wireless tab, it displays the MAC address wireless like: XX:1E.

  So, now, I try to get into this 'new' MAC address in the MAC of the router EA6500 filter just to see if it will work with this MAC address "without papers" of the wireless device.  At first, it seems to work.  The WUMC710 of blue light will come on indicating that a wireless connection has been established with the router.  BUT nowhere in the web interface of EA6500 says that the WUMC710 has a DHCP connection with the router.  And, if I connect my laptop directly to one of the WUMC710 Ethernet ports, there is no connection to the Internet via the router (as long as the MAC filtering is enabled).

  I did Factory Reset a few times now and no difference.

  Firmware is the factory default - it is there no update of the firmware available, yet.

  I spent several hours trying to understand what is happening with this device and go round and round in circles in trying different things.  I can only conclude WUMC710-AC is defective, or requires a firmware fix - but none are available.

  Am I missing something here?  Or Cisco does suggest a fix for the firmware for the WUMC710-AC?

  (I don't really like to run my network wireless MAC address filtering active wireless.)

  Kind regards

  Jeff

  Cisco-Linksys 2 support with me today confirmed what I thought it was a possible firmware bug, is actually undocumented features of the WUMC710, by design.  And they agreed that they will update the documentation for WUMC710 to take account of these features and system requirements.

  Just like a reference to new users of the WUMC710 AC wireless bridge, I will summarize here the requirements for WUMC710 wireless bridge to work properly with the router, Cisco-Linksys AC6500 Wireless, when MAC filtering is enabled.  If all goes well, this information will save some other people the many hours I spent to dig through the documentation and the FAQ to try to understand what it takes to connect successfully devices behind the bridge of WUMC710 to the AC6500 router - when the MAC address filtering is enabled:

  The following MAC address must be entered in the AC6500 router table filtering of MAC addresses to connect devices behind the bridge WUMC710 wireless to the Internet:

  1. The MAC address of the bridge wireless WUMC710 wireless.
  2. The address MAC LAN of the WUMC710 bridge.
  3. Addresses MAC LAN of each LAN device connected to the LAN Ports of the WUMC710 bridge.

  That in a few words.

  With this information, devices behind the WUMC710 of Internet connection (with the active MAC filtering) is a breeze.

• MAC filtering with guest network

  Hello, I have E4200v2 of Cisco, and after someone hacked password of my router, I was forced to activate a white list of MAC filtering. Problem is that I also like to activate a network of comments so my small business clients could still connect to the wifi, without acceding to out to home PC (and drink our bandwidth).

  Is this possible? Thank you.

  1. make sure that disable WPS.

  2 change the router password on the Administration page to guarantee something.

  3 make sure to disable remote management.

  4. set WPA2 Personal with a new strong password.

  5 disable the feedback network.

  That will protect your network. Piracy is not possible unless someone passes the WPA2 password or have access to the router and ethernet ports.

  The MAC filter won't help you. MAC addresses are transferred, are easily picked up and not cloned.

  If you want to activate the guest network you must accept the fact that other computers connect to your guest network and try to access the internet from there. They manage unless they know the password, but still, they can connect to the guest network because it is not protected. Only access from the network invited to the internet is protected.

  He must also accept the fact that you can "drink your bandwidth. If you do not like who don't offer guest access.

• WAP54g does not recognize the IP address of my laptop with active Mac filtering

  I have reset my factory default WAP54g v3.05 to allow access to the older computer to my network.

  Now, I reinstalled for better security using my new laptop: no SSID broadcast and WPA2-Personal encryption. However, when I activate the Mac filtering and allow my laptop more recent, the WAP54g does not recognize.

  Disable Mac filtering and my laptop is back on the network.

  Any suggestions to solve this problem would be appreciated.

  Make sure that the MAC address of the wireless network adapter in the MAC address filtering tab. To get the MAC address of the wireless network card. Click on start-> Go to run-> type-> CMD-> Hit Enter type ipconfig/all

  This will give a show you the MAC address for adapter ethernet and a wireless adapter. You must select one for the wireless network adapter.