PIX 515e VPN 3005 concentrator cannot pass phase 1

Similar Questions

• Cisco VPN Client behind PIX 515E,-> VPN concentrator

  I'm trying to configure a client as follows:

  The user is running Cisco VPN Client 4.0. They are behind a 6.1 PIX 515E (4), and I need to connect to a VPN concentrator located outside of our network. We use PAT for address translation. As far as I know, to allow ipsec through Firewall 1 tunnel, I need to upgrade the pix to 6.3 and activate "fixup protocol esp-ike.

  Is there another way to do this? I am also curious to know how much more easy/better this will work if we were dealing with pptp.

  You don't necessarily need to fixup protocol esp-ike active. The remote Hub there encapsulation NAT - T enabled so that clients behind the NAT can run?

• PIX 515E - VPN connections

  Hello

  I have pix 515E and I configured a VPN on it. My users connect to my network from the internet via the Cisco VPN client.

  I have problem, only their LAN machine can do VPN from Cisco VPN client to my network at once.

  Users are connected to the internet via an ADSL router and the LAN switch.

  --------------------------------------------------

  PIX Config:

  6.3 (4) version PIX

  interface ethernet0 car

  Auto interface ethernet1

  ethernet0 nameif outside security0

  nameif ethernet1 inside the security100

  enable encrypted password xxxxxxxxxxxxxxx

  xxxxxxxxxxxxxxxx encrypted passwd

  hostname ABCDEFGH

  ABCD.com domain name

  clock timezone IS - 5

  clock to summer time EDT recurring

  fixup protocol dns-length maximum 512

  fixup protocol ftp 21

  fixup protocol h323 h225 1720

  fixup protocol h323 ras 1718-1719

  fixup protocol http 80

  fixup protocol rsh 514

  fixup protocol rtsp 554

  fixup protocol sip 5060

  fixup protocol sip udp 5060

  fixup protocol 2000 skinny

  fixup protocol smtp 25

  fixup protocol sqlnet 1521

  fixup protocol tftp 69

  inside_out to the list of allowed access nat0_acl ip 192.168.1.0 255.255.255.0 192.168.2.0 255.255.255.0

  list of allowed shared access ip 192.168.1.0 255.255.255.0 192.168.1.0 255.255.255.0

  pager lines 24

  Outside 1500 MTU

  Within 1500 MTU

  IP address outside xxx.xxx.xxx.xxx 255.255.255.0

  IP address inside 192.168.1.1 255.255.255.0

  alarm action IP verification of information

  alarm action attack IP audit

  IP local pool vpnpool 192.168.2.1 - 192.168.2.254

  PDM logging 100 information

  history of PDM activate

  ARP timeout 14400

  Global interface 10 (external)

  NAT (inside) 0-list of access inside_out-nat0_acl

  NAT (inside) 10 0.0.0.0 0.0.0.0 0 0

  Route outside 0.0.0.0 0.0.0.0 xxx.xxx.xxx.xxx 1

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225

  H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00

  Timeout, uauth 0:05:00 absolute

  GANYMEDE + Protocol Ganymede + AAA-server

  AAA-server GANYMEDE + 3 max-failed-attempts

  AAA-server GANYMEDE + deadtime 10

  RADIUS Protocol RADIUS AAA server

  AAA-server RADIUS 3 max-failed-attempts

  AAA-RADIUS deadtime 10 Server

  AAA-server RADIUS (inside) host ABCDE timeout 10

  AAA-server local LOCAL Protocol

  RADIUS protocol radius AAA-server

  Radius max-failed-attempts 3 AAA-server

  AAA-radius deadtime 10 Server

  RADIUS protocol AAA-server partnerauth

  AAA-server partnerauth max-failed-attempts 3

  AAA-server deadtime 10 partnerauth

  partnerauth AAA-server (host ABCDEFG myvpn1 timeout 10 Interior)

  Enable http server

  http 192.168.1.0 255.255.255.0 inside

  No snmp server location

  No snmp Server contact

  SNMP-Server Community public

  No trap to activate snmp Server

  enable floodguard

  Permitted connection ipsec sysopt

  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto-map dynamic outside_dyn_map 20 the transform-set ESP-3DES-MD5 value

  map outside_map 65535-isakmp ipsec crypto dynamic outside_dyn_map

  card crypto client outside_map of authentication partnerauth

  outside_map interface card crypto outside

  ISAKMP allows outside

  ISAKMP key * address 0.0.0.0 netmask 0.0.0.0

  ISAKMP identity address

  part of pre authentication ISAKMP policy 8

  ISAKMP strategy 8 3des encryption

  ISAKMP strategy 8 md5 hash

  8 2 ISAKMP policy group

  ISAKMP life duration strategy 8 the 86400

  part of pre authentication ISAKMP policy 10

  ISAKMP policy 10 3des encryption

  ISAKMP policy 10 sha hash

  10 2 ISAKMP policy group

  ISAKMP life duration strategy 10 86400

  vpngroup myvpn address vpnpool pool

  vpngroup myvpn ABCDE dns server

  vpngroup myvpn by default-field ABCD.com

  splitting myvpn vpngroup split tunnel

  vpngroup idle 1800 myvpn-time

  vpngroup myvpn password *.

  Telnet 192.168.1.0 255.255.255.0 inside

  Telnet timeout 5

  SSH timeout 5

  Console timeout 0

  dhcpd address 192.168.1.200 - 192.168.1.254 inside

  dhcpd dns ABCDE

  dhcpd lease 3600

  dhcpd ping_timeout 750

  field of dhcpd ABCD.com

  dhcpd outside auto_config

  dhcpd allow inside

  Terminal width 80

  --------------------------------------------------

  Thanks in advance.

  -Amit

  Try to add the "isakmp nat-traversal" command to your PIX. I suspect what happens is that Remote LAN users is translated to a single IP address as they pass through the DSL connection. I also assume that the machine doing the translation has a capacity of IPSec passthrough. Linksys routers would be a good example of this type of NAT device that allows IPSec pull-out.

  If that's the case, that a single VPN connection will be able to operate both. The above command will turn PIX detect clients that are located behind a NAT device, and then try to configure the VPN sessions in UDP packets and so to work around the limitation of NAT and IPSec passthrough device.

• Recovery password: VPN 3005 concentrator

  How 3005 Concentrator VPN admin password.

  Here is the procedure

  http://www.Cisco.com/en/us/products/HW/vpndevc/ps2284/products_password_recovery09186a008009434f.shtml

• Client VPN vs VPN 3005 concentrator using the Dial - up Internet GPRS connection

  Hello!

  I'm in trouble by using the GPRS Internet connection. I installed a VPN Client to connect to our VPN 3005 and it works fine but only using a V.90 Internet Dial-up regular connection. When I use GPRS I have access to the Internet, my VPN Client to connect successfully to the VPN3005, but I get no access to the Remote LAN (not even the ping test!). Can the overhead of 3DES cause something to do with this topic?

  Kind regards

  Russ

  I also activated the udp encapsulation mode, however I notice that the success rate for the vpn full implementation of IKE (complete Exchange of keys and connection) is only abt 50% of no. some trys. I wonder if you have such an experience... Not sure it's because of the latency in GPRS.

• Cannot access Internet on VPN 3005 concentrator

  I installed a new concentrator 3005. I am able to connect using the Cisco VPN client. Everything seems to work except the Internet. I am able to access everything in the local network, including local intranet Web pages. If I try to access Web pages on the outside, it does not. Any ideas?

  OK, so it seems there is a configuration or a problem with routing somewhere. Concentrator vpn routing table look like? Is there a default route set correctly? You can use ping to ping the default gateway?

  NAT is used? Is it possible the problem is that packages are not properly natted out to internet?

• VPN 3005 concentrator Web Administration fails

  I have a vpn concentrator 3005 I can't connect to the web administration page. When I have the access concentrator, I get an HTTP 403 forbidden error. IE, the details of the error is "this error (HTTP 403 Forbidden) means that Internet Explorer was able to connect on the site, but it doesn't have permission to view the Web page." I tried several machines and Firefox as well, but all give the same error. I have no problem with the administration via telnet, but wishes to get the web interface works again. I even tried updating the hub to 4.7.2.P (from 4.7.2.O), but it does not solve the problem either. I also noticed an error in the event log which shows demand and an error HTTP 404 not found (/). Any ideas?

  On your interfaces, for example, "Configuration | Interfaces | Ethernet 1 ", on the WebVPN tab you have the check box for"allow management HTTPS sessions "?

• How to export the list of internal users from VPN 3005 concentrator?

  I would like to be able to export the list of users for the purpose of documentation. Is this possible to do with the 3005?

  Thank you

  Raul

  It's not easy passing just to get the list of name of user, but you can get the whole config and then grab users ot there in a couple of ways.

  In XML format, which is easier to read, go to Admin - Mgmt - XML Export file and export the config file to any file name. Then under the file Mgmt section this file that will appear in a separate window. Search to find the sections of the user names and passwords.

  Text (a bit like an in the Windows .ini file), go to settings to access Admin - rights of access - and no Config File Encryption value. Save the configuration. Then go to file Mgmt and display the CONFIGURATION file, search for [user *. 1] to find all of the names of users and their values. This way is not very useful to be honest.

• Several outbound VPN connections behind PIX-515E

  I will take a PIX-515E off-site for a provision of access internet location. I have several people behind this PIX, who will have to return to the same Office VPN. One person can VPN through the PIX very well, but if someone else tries to VPN they cannot. Once the first person has disconnected for 10 minutes, then the next person can connect. I activated the NAT - T and added fixup protocol esp-ike. What can I do it wrong? Thank you.

  fixup protocol esp-ike - allows PAT to (ESP), one tunnel.

  Please remove this correction.

  If the remote site has NAT - T enabled, then you should be able to use NAT - T and more than 1 user should be able to use behind the PIX VPN client.

  See you soon

  Gilbert

• Cisco PIX 501 to Cisco 3005 concentrator via remote access

  Hello people,

  I need your help.

  We got a Cisco PIX 501 in one place and this pix is configured for pppoe connection. The pix connects to internet via the pppoe client. an official ip address ping works well.

  So what I want to do is to establish a tunnel von between this pix and a cisco 3005 concentrator.

  But I failed to establish it.

  Here are the pix config. the acl? s are only for the test and will be replaced if it works.

  6.3 (4) version PIX

  interface ethernet0 10baset

  interface ethernet1 100full

  ethernet0 nameif outside security0

  nameif ethernet1 inside the security100

  activate the password xxx

  passwd xxx

  hostname PIX - to THE

  domain araukraine.ua

  fixup protocol dns-length maximum 512

  fixup protocol ftp 21

  fixup protocol h323 h225 1720

  fixup protocol h323 ras 1718-1719

  fixup protocol http 80

  fixup protocol they 389

  fixup protocol rsh 514

  fixup protocol rtsp 554

  fixup protocol sip 5060

  fixup protocol sip udp 5060

  fixup protocol 2000 skinny

  fixup protocol smtp 25

  fixup protocol sqlnet 1521

  fixup protocol tftp 69

  names of

  outside ip access list allow a whole

  inside_access_in ip access list allow a whole

  pager lines 24

  opening of session

  Monitor logging warnings

  logging warnings put in buffered memory

  MTU outside 1456

  MTU inside 1456

  IP address outside pppoe setroute

  IP address inside 192.168.x.x 255.255.255.0

  alarm action IP verification of information

  alarm action attack IP audit

  PDM location 192.168.x.x 255.255.255.224 inside

  forest warnings of PDM 500

  history of PDM activate

  ARP timeout 14400

  Global 1 interface (outside)

  NAT (inside) 1 0.0.0.0 0.0.0.0 0 0

  outside access-group in external interface

  inside_access_in access to the interface inside group

  Timeout xlate 0:05:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225

  H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00

  Timeout, uauth 0:05:00 absolute

  GANYMEDE + Protocol Ganymede + AAA-server

  AAA-server GANYMEDE + 3 max-failed-attempts

  AAA-server GANYMEDE + deadtime 10

  RADIUS Protocol RADIUS AAA server

  AAA-server RADIUS 3 max-failed-attempts

  AAA-RADIUS deadtime 10 Server

  AAA-server local LOCAL Protocol

  the ssh LOCAL console AAA authentication

  Enable http server

  255.255.x.x 192.168.x.x http inside

  No snmp server location

  No snmp Server contact

  SNMP-Server Community public

  No trap to activate snmp Server

  enable floodguard

  255.255.x.x telnet inside 192.168.x.x

  Telnet timeout 5

  SSH 194.39.97.0 255.255.255.0 outside

  SSH timeout 5

  management-access inside

  Console timeout 0

  VPDN group pppoe_group request dialout pppoe

  VPDN group pppoe_group localname [email protected] / * /

  VPDN group ppp authentication pap pppoe_group

  VPDN username [email protected] / * / password *.

  encrypted privilege 15

  vpnclient Server 212.xx.xx.xx

  vpnclient mode network-extension-mode

  vpntest vpngroup vpnclient password *.

  vpnclient username pixtest password *.

  Terminal width 80

  the hub, I created a user pixtest, a group vpntest and I? ve created the rules of the network for example to what server, users behind the pix will be able to access.

  And that? s all.

  I couldn't send you exit pix or hub because I don't have an error or a message that the tunnel will be established.

  What can be wrong?

  Thanks for the replies

  This configuration example shows how to create an IPsec tunnel to a computer that is running the Client VPN Cisco's (4.x and later versions) to a Cisco VPN concentrator 3000 to allow the user to safely access the network inside the VPN concentrator.

  http://www.Cisco.com/en/us/products/HW/vpndevc/ps2284/products_configuration_example09186a008026f96c.shtml

• Cannot ping PIX 515e Interfaces

  I know it's a very silly question for this forum, but I have already tried many things and cannot get the answer from the PIX firewall interfaces.

  It's my (very easy) installation:

  Using a FastEthernet port on router, I have a cable connected directly to the outside I / F of the PIX-515e. (Crossover cable works, I have already tested). Router <-->PIX directly connected.

  I configured the PIX firewall to allow pings (I used different commands):

  ICMP allow any response of echo outdoors

  ICMP allow all outside

  ICMP permitted - echo outside response

  I tried to configure each of them and also combined.

  Also tried to send the PIX to its default values. Supposed to be after that the PIX should allow all pings if no "icmp" command is configured.

  I have configured the ports on both sides to 100 Full

  On both sides of the link (PIX and router) I have the links to the top. The lights are on.

  The 'show interest' on the PIX firewall shows to the top/top

  The same thing on the router...

  The two interfaces are configured in

  10.1.1.0/24 (10.1.1.1 & 10.1.1.2)

  What I am doing wrong?

  This should be very easy...

  Hello

  Majority of the time interfaces refuses explicitly to ICMP packets unless you indicate otherwise. Here is a link to a pretty good setup guide... Have a look at the link to the ping Security Appliance Interfaces section in this guide. I'm really frustrated myself during the installation/testing phase because the pings are not working and it helped. Hope this helps a little and makes your life easier =) (rate if it please and thank you)

  http://www.Cisco.com/en/us/products/ps6120/products_configuration_guide_chapter09186a00805521b6.html#wp1059645

  Thank you

  Chris

• VPN - Pix 515e for Cisco router

  I have the following Setup and I can't seem to get the next tunnel. My end is a PIX 515e race 7.2 (4). The other end is a Cisco router-not sure of the model or version of the IOS.

  PIX:

  90 extended access-list allow ip host a.a.a.a host b.b.b.b

  NAT (inside) - 0-90 access list

  correspondence address card crypto mymap 20 90
  card crypto mymap 20 peers set x.x.x.x
  map mymap 20 set transformation-strong crypto
  mymap outside crypto map interface
  ISAKMP crypto identity hostname
  crypto ISAKMP allow outside
  crypto ISAKMP policy 8
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 86400

  tunnel-group x.x.x.x type ipsec-l2l
  tunnel-group ipsec-attributes x.x.x.x
  pre-shared key 12345

  Router:

  / * Style definitions * / table. MsoNormalTable {mso-style-name : « Table Normal » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-qformat:yes ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 à 5.4pt 0 à 5.4pt ; mso-para-margin : 0 ; mso-para-marge-bottom : .0001pt ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-fareast-font-family : « Times New Roman » ; mso-fareast-theme-font : minor-fareast ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ; mso-bidi-font-family : « Times New Roman » ; mso-bidi-theme-font : minor-bidi ;} / * Définitions de style * / table. MsoNormalTable {mso-style-name : « Table Normal » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-qformat:yes ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 à 5.4pt 0 à 5.4pt ; mso-para-margin : 0 ; mso-para-marge-bottom : .0001pt ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-fareast-font-family : « Times New Roman » ; mso-fareast-theme-font : minor-fareast ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ; mso-bidi-font-family : « Times New Roman » ; mso-bidi-theme-font : minor-bidi ;}

  SDM_5 extended IP access list

  permit ip host b.b.b.b host a.a.a.a

  ISAKMP crypto key 12345 address y.y.y.y no.-xauth

  map SDM_CMAP_1 5 ipsec-isakmp crypto

  Description vpn for laboratory

  defined peer y.y.y.y

  game of transformation-ESP-3DES-SHA

  match address SDM_5

  I'm running him debugs following:

  Debug crypto ipsec enabled at level 1
  ISAKMP crypto debugging enabled at level 1

  I get the following debug output:

  August 16-04:16:10 [IKEv1]: IP = x.x.x.x, counterpart of drop table counterpart, didn't match!
  August 16-04:16:10 [IKEv1]: IP = x.x.x.x, error: cannot delete PeerTblEntry

  Isa HS her

  IKE Peer: x.x.x.x
  Type: user role: initiator
  Generate a new key: no State: MM_WAIT_MSG2

  Any ideas?

  Thank you

  Dave

  If you see the MM_WAIT_MSG2, which means that her counterpart (the other side) does not answer and this side where you can see the status MM_WAIT_MSG2 sent the first message IKE, however, did not hear of the peer.

  You can check if UDP/500 is stuck on the way between the 2 sites.

  Try running traffic on the other side and see if you also get the same status of MM_WAIT_MSG2. If you do, that confirms 100% 500/UDP is blocked on the way between the 2 sites.

• Cisco VPN Client Authentication - PIX 515E-UR

  Hi all

  I need your expert help on the following issues I have:

  1. I would like to create more than 1 client VPN on my PIX-515E groups. This is so that I can give a different part of the internal network access to different type of VPN connection. For example, I want a group to have no XAUTH, while the other group must use RADIUS XAUTH. Is it possible for me to do this? I see the PIX automatically enable RADIUS on both groups of VPN clients.

  2. the RADIUS server is a Microsoft ISA with IAS server and it is located on the PIX inside interface. The VPN endpoint is external interface of the PIX. Is there a problem with this Setup? Do I need to have the RADIUS server that is located on the external interface?

  3 can. what command I use to debug RADIUS authentication?

  Thanks in advance for your help.

  Hi vincent,.

  (1) you can use the vpngroup *-authentication server ipaddress to specify the IP address of the Radius Server on a particular group... If you do not specify this, the authentication of the user is made locally... also check for vpngroup * order of user authentication

  (2) there should be no problem with the installation of your... should work fine... If the RADIUS is outdoors, it is subject to many attacks... so have it inside...

  (3) use the "RADIUS session debug" or "debug aaa authentication..."

  I hope this helps... all the best... the rate of responses if found useful

  REDA

• PIX 515E for VPN remote site

  Hello

  7.0 (1) version pix

  ASDM version 5.0 (1)

  I have a situation where you go paas-thanks to the VPN feature goes on our PIX 515E. I tried to put this on the pix using a VPN Wizard Site to site

  who is enabled. I was unable to connect to the pix from the remote site. Witch's journal replied negotiate the pix is OK and the success

  The problem is when I try to set up the tunnel to the top of the remote site. I fall without failure.

  where can I see the vpn pix for error log?

  is there a manual for the solution of site to site VPN using the wizard

  Help, please.

  Thanks in advance

  http://www.Cisco.com/en/us/partner/products/HW/vpndevc/ps2030/products_configuration_example09186a00804acfea.shtml#ASDM

  the section 'use adsm' (step 14) gives an example on how to set up vpn lan - lan via adsm

  Newspaper to go to the section "check".

• PIX 515E and remote access VPN

  I use a PIX 515E with: ASDM Version: 5,0000 51 PIX Version: 8.0 (4) and configure it with remote access VPN.

  I would like to get an email every time that a user login (and or disconnection) to the VPN. Remote clients use the Cisco VPN Client.

  Any help is appreciated,

  Hello

  Here is a link to the email configuration when you log in to the ASA/PIX: http://www.cisco.com/c/en/us/support/docs/security/pix-500-series-security-appliances/63884-config-asa-00.html#anc7

  Then you can create a list of message to send the logs only for the connection/disconnection of the VPN user: http://www.cisco.com/c/en/us/support/docs/security/pix-500-series-security-appliances/63884-config-asa-00.html#anc18

  There is a wire that is linked here: https://supportforums.cisco.com/discussion/10798976/asa-email-logging-issue