Placement of module problem

Similar Questions

• Download of modules problem

  I find the add-on I want, press 'Add to firefox', then the status bar instantly comes up with 'the module download' with the status bar complete with 0 bytes, then nothing! Don't see anywhere, its certainly not appearing is not in my extensions modules! I thought it was a problem with the wonderful Java but that seems to work ok... I think so?

  Help, please!

  Hello

  The reset Firefox feature can solve a lot of problems in restaurant Firefox to its State default factory while saving your bookmarks, history, passwords, cookies and other essential information.

  Note: After Firefox reset, you will lose all extensions, toolbar customizations, and certain preferences. See article Firefox Refresh - reset modules and parameters for more information.

  To reset Firefox:

  1. Open the troubleshooting information page using one of the following methods:
     • Click the menu button

       

       click Help

       

       and select troubleshooting information. Should open a new tab containing your troubleshooting information.

     • If you are unable to access the Help menu, type Subject: support in your address bar to bring up the troubleshooting information page.
  2. At the top right of the page, you should see a button that says "Reset Firefox" which looks like this:

     

     . Click on it.

  3. Firefox will close and reset. After it's done, Firefox will display a window with information that is imported.
  4. Click Finish and reopen Firefox.

  This corrects the problem? Please report to us!

  Thank you.

• Portege Z30 Module problem - A - 13 L 3 G

  I had a problem with a new Portege Z30 - A - 13 L.

  Module 3 G / 4G do not work. As a first step, the Air software map Watcher on the first Installation of Windows 7 detects the sim card and showed a signal, but it Air card Watcher Software still not said no reception (in German: Kein receipt).

  I also put the right apn in the profile.
  I had this problem with 2 different operators sim cards.

  Cause I wanted to use Windows 8.1 anyway I installed it with the original recovery disks.
  The original Windows 8.1 don t comes with Air card Watcher, so you must do with the instruments of the Board of Directors of Windows 8. Windows 8.1, I had a same problem. It detects the SIM, but it says no network (in German: Kein Netz). I put t found the possibility of changing the apn in 8.1 of Windows until you have a mobile connection.

  Initially the Device Manager displays the Module of Sierra Wireless EM 7305 as a network card.
  Then, I uninstalled the driver of Sierra Wireless and installed the Toshiba page.

  After that the Sierra Wireless Module presents itself as a Com device in Device Manager. The cause so much of this networker of Sierra Wireless adapter isn t it, the mobile broadband connection don t even shows charms Windows 8.1 bar upward.

  After that I reinstalled again the image Windows 8.1 with the original recovery disks.
  I saw said that Sierra Wireless Driver has been installed, but the Module EM7305 of Sierra Wireless is presented with an exclamation mark in Device Manager.

  Then I uninstalled and installed the driver manually again.
  He appears again as com device in Device Manager.

  So I think that the module has been a hardware failure. What do you think?

  > After that I reinstalled again the image Windows 8.1 with the original recovery disks.
  > I saw said that Sierra Wireless Driver has been installed, but the Module EM7305 of Sierra Wireless is presented with an exclamation mark in Device Manager.

  On the page of the Toshiba UE driver, you can find and download the [Sierra Wireless Driver LTE 4 G driver | http://www.toshiba.eu/innovation/download_driver_details.jsp?service=EU&selCategory = 2 & selFamily = 4 & selSeries = 362 & selProduct = 17549 & STAS hortMod = null & language = 13 & selOS = 46 & selType = all & year = upload & monthupload = & dayupload = & useDate = null & mode = allMachines & search = & action = search & macId = & country = a he's & selectedLanguage = 13 & type = all & page = 2 & ID = 90092 & OS ID = 46 & driverLanguage = 42]
  This Wireless Broadband Mobile driver is used to transfer data at higher rates and greater capacity.
  Install it!

  Also 3G must be activated before you try to establish a 3 G connection.
  Please check if the 3G module has been activated correctly!

  Recommend checking this information page of Microsoft Mobile Broadband end-to-end
  http://Windows.Microsoft.com/en-us/Windows-8/mobile-broadband-from-start-to-finish

  You will find different troubleshooting tips.

  In the case where you have a signal but you can't connect the possible reasons could be:
  You don t have a valid data subscription.
  The name of the access point (APN), user name or password used for the connection is not valid.
  You're roaming and the selected network operator doesn't allow data services or you don t have roaming enabled for data services.

• Tecra R10 - 10W / R10 - 111 3 G module problem

  Hello

  Module 3G does not work after the update. NA? find answers online. Maybe you know what to do:

  When I start the system from scratch, I just open the software Connect from Toshiba and the laptop connects after the network authentication. Usually after a certain time the yellow triangle with exclamation point appears and from that moment the system is connected limited/locally only. When I use vista tools to set up the problem I get the message that there could be a problem and I should connect via another network (lan, WiFi, BT, a? ¦) a? not really a solution to my problem!

  To restart the internet I need to disable the Toshiba g 3507 module and stop the wireless software Connect, wait about 10 seconds and then re-enable the module and restart wireless connect software. In fact, there is no option in the turn off the TPM in the wireless not connect software. When you work with my laptop, I need to reconnect it several times per day and this very annoying. Toshiba could not help me? They told me to call the hotline!

  I did all the updates that are provided by Toshiba, but it does not change.

  Any idea?

  See you soon
  Patrick

  Maybe the SIM card is loose, have you tried reinstalling the SIM card?

  Have you also updated the BIOS?

  Did you install any other software that may be contradictory? (For example, a USB 3 G external or similar device)

  Have you tried running the recovery to reinstall Windows.

  If it still does not work, then it might be a hardware problem, in which case you will have to send the laptop to an ASP for repair. The list of ASP can be found on the Toshiba site (the site of www.toshiba-europe.com assuming you're in EU)

• 8 Dell in the Gallery place video playback problem

  I have a 8 place running on 4.3 Jellybean and whenever I try to play a video that I recorded from the gallery application that is enabled by default on the Tablet, it restarts. Just, it shows the Dell logo and goes back to the lock screen, I. I can't play any video in the Gallery, because after 2 seconds or so, it restarts again. I searched the internet if someone had similar problems, but did not find any solution.

  Download MX Player from the game store.  Then try to play a video again.  This time, only a menu should appear and ask which player you want to use.  MX player or video player.  The options are 'once' (it will give you a choice once again). Or "always."  If you choose 'always' the player you have chosen will run automatically whenever you play a video. Choose mx player (still) to set it as a default.  He may ask you to install a codec from the game store.  Go ahead and do it.  See if it works.

• Firmware for the F348XP - N77 - 23 Nexus module problems

  H,

  I hope you had great Christmas time! I am currently working on the new Nexus lab, and I have a challenge.

  I try to get 1/10 Gbit / s Ethernet Module running. Do you know where to find firmware for this module and how to set the variable initialization for her? What I get so far:

  introduce the module:

  Status of Module Type mod Ports model
  --- ----- ----------------------------------- ------------------ ----------
  1 48 1/10 Gbit / s Ethernet Module N77 - F348XP - 23 ok
  2 48 1/10 Gbit / s Ethernet Module N77 - F348XP - 23 powered-dn! This one, with that I'll have the problem
  3 0 active supervisor Module-2 N77-SUP2E *.
  4 0 supervisor Module-2 N77-SUP2E ha-standby

  When I try to turn it on by entering

  (config) # No module poweroff 2

  I'm more about newspapers:

  2015 Dec 16 00:38:23 % xxx platform-2-MOD_DETECT: Module detected 2 (serial number JAE19290A6J) Type of Module-1/10 Gbps Ethernet Module model N77-F348XP-23
  2015 Dec 16 00:38:23 % xxx platform-2-MOD_PWRUP: Module 2 under voltage (serial number JAE19290A6J)
  2015 Dec 16 00:38:23 % xxx platform - 5 - module MOD_STATUS: Module 2 - current situation is MOD_STATUS_POWERED_UP
  2015 Dec 16 00:40:02 xxx % BIOS_DAEMON-SLOT2-5-BIOS_DAEMON_LC_PRI_BOOT: System started from the main BIOS Flash
  2015 Dec 16 00:40:05 xxx % FW_APP-SLOT2-2-FIRMWARE_IMAGE_LOAD_ERROR: error extraction and loading Firmware: firmware Flash and software images are bad
  2015 Dec 16 00:40:06 xxx % MODULE-2-MOD_FAIL: initialization of the module 2 (serial number: JAE19290A6J) failed
  2015 Dec 16 00:40:06 xxx last message repeated 1 time
  2015 Dec 16 00:40:06 xxx % PLATFORM-2-MOD_PWRDN: Module 2 power off (serial number JAE19290A6J)
  2015 Dec 16 00:40:06 xxx % PLATFORM-5-module MOD_STATUS: Module 2 - current situation is MOD_STATUS_CONFIGPOWERED_DOWN
  2015 Dec 16 00:40:06 xxx % PLATFORM-5-module MOD_STATUS: Module 2 - current situation is MOD_STATUS_POWERED_DOWN

  I take the problem is with the firmware, but I can't find the path to it. It there is no defined variable initialization is module 1, or 2, but module 1 started without problem.

  XXX # display the start module 1
  No set variable initialization module
  XXX # display the start module 2
  No set variable initialization module

  I can see the bin files under
  XXX # cd bootflash://module-4/
  bootflash://module-4/20150808_221923_poap_7580_init.log bootflash://module-4/vdc_3
  bootflash://module-4/20151211_010151_poap_8037_init.log bootflash://module-4/vdc_4
  bootflash://module-4/20151211_015441_poap_7723_init.log bootflash://module-4/vdc_5
  bootflash://module-4/lost+found bootflash://module-4/vdc_6
  bootflash://module-4/N7700-S2-dk9.6.2.12.bin bootflash://module-4/vdc_7
  bootflash://module-4/N7700-S2-kickstart.6.2.12.bin bootflash://module-4/vdc_8
  bootflash://module-4/scripts bootflash://module-4/vdc_9
  bootflash://module-4/vdc_2

  but I'm not able to assign variable initialization module, I see 1 - sup and sup - 2 only

  XXX (config) # boot system bootflash://module-4/n7700-s2-dk9.6.2.12.bin?
  
  SUP-1 input sup-1 to set up the 1st sup
  SUP-2 input sup-2 to set up the 2nd sup

  I hope that you would be able to help!

  Happ new year as well! :)

  Hello

  Do you have these linecards at the same time? I see that module 1 is the same model and do not have any problems. Did you open a SR of TAC for the same thing? I saw some similar cases where these messages could be the result of a faulty hardware, but you can open a folder of TAC to continue the investigation.

  HTH,

  Wes

• BlackBerry® Smartphones put E-mail in place the 8520 problem

  I can't send emails... maybe I has not properly implemented the enamel, cause the implementation of Wizard only displays bb enterprise server as an e-mail put in place option. need help

  problem of sorting... thnx!

• Link to the Gallery module problem

  I have a photo gallery module on http://grapeleafcafeandgrill.BusinessCatalyst.com/Gallery.html links low on the right do not run properly. Can someone please help me with this?

  I am answering my own post. Please do not take into account. I was in a bootstrap carousel to solve my problem.

• CC 2014 on iMac 2011 - video Module problem

  I just installed the first Pro 2014 CC version on my iMac and now get this message.  Error "Premiere Pro could not find capable video game modules"

  Self-service on the Adobe site support is insufficient, fails to provide valuable support.

  Does anyone have the same problem with this version and, if so, the indices on fixing it, without having to buy a new Mac?  And Yes, I have 2 GB on the GPU, 32 GB of RAM.

  Hi NCMUK,

  Try this:

  • Go to the following locations and rename the folders "old_folder Name" (like old_Adobe)
    • User/user/library/Application Support and rename the Adobe folder.
    • User/Library/Preferences and rename the Adobe folder.
    • Navigate to the Documents folder then to Adobe/Premiere pro/8.0 and rename the 8.0 folder.

  Thank you
  Kevin

• Place the Image - problems "sort by".

  I'm having a problem with my image placement in all adobe programs.

  When I go to 'place' a picture in photoshop or indesign, my file directory appears and is sorted by number changed. I need sorted by name (which is usually the default). Can I change the option "sort by", but next time I want to place an image, it is updated so the last. I'm putting hundreds of images in this document and it would be must easier than my images have been sorted by name whenever I went to place an image.

  All my programs outside the Adobe type with a default name and my programs Adobe allows. I can't understand what causes this problem, and my colleagues computer seems to work very well! Please let me know if you have any suggestions!

  Thank you!

  If you use CS2 you lucky.  Look at the bottom left of the file - open dialog box.  You see a button titled [use and Adobe dialog] or [Use OS dialog]?  If so, try clicking on it.  I bet the other form of the dialog box will remember the type of file you like.

  There are RUMORS that one can cause the sort order in a XP OS dialog box change by changing it manually (by clicking on the title of the file name), and then hold down the CTRL key and the cancellation of dialog box, but I personally haven't seen this book.  It may be one of those old wive tales.

  -Christmas

• Module problems

  The main application mxml page is just a white page that on completetion, load the menu module (works well)
  
  The menu has a number of buttons, each button will load a separate module.
  
  Problem,
  
  The existing module does not get unloaded.
  
  The code I use in the click event is:
  removeModule (mLoader); createModule (mLoader, ' views/newshift.swf')
  
  Load the new module, it does not unload the menu module.
  
  What I am doing wrong?
  Y at - it no example apps out there, I can look at?
  
  Ken

  Not wory, I made the pages again and it worked as it should.

  Ken

• Tecra R10 - 10W / R10 - 111 3 G module problem see also messages from May 25

  Thanks for your fast replay.

  Yes, I have tried to reinstall the SIM card and updated everything what is possible from the homepage, Microsoft and Toshiba. No external devices (e.g. 3 G USB) installed and windows is retrieved by a full licensed Windows Vista Business (No. Toshiba OEM more) just a couple of days.

  The only thing I discovered is that the 3G module Firmware is not updated. I didn't recognize the pop-up window when before updating, but yesterday, I got the day when/after massage:

  "Generation data has not changed, probably failed update"

  I tried to update with an activated, a connected and a module 3G disabled (in that order) but no change. I always get the same message once the module is restarted during the FW update. The module was not disconneced by stopping the system or any other stop option during update FW (as read in the instructions). The old FW was working fine until I did some updates to the Toshiba homepage (always ask Tempro). Any idea?

  Control on while you try to update the firmware with the original image of Windows from Toshiba?

  Where did you got the firmware?

• Input RS232 module problem

  Hi all

  I am trying to read and save data to an account with DASYLab.

  DASYLab and the Windows Device Manager to detect the right COM port, although sometimes I can't see the port connected to the command prompt (using the 'mode' command).

  Everything seems fine, but I don't get all the data in the RS232 input channel.

  I tried to follow the module interface while asking data (using 2WOW\f), but without success!

  I appreciate your help and your suggestions.

  
  

• serial port after the installed DSC module problem

  Hello..

  I want to GSM(with labVIEW) and PLC interface, My PLC will work in serial port only.

  In my PC, I have 3 serial ports. before installing the DSC module in my system, I can configure the ports series all the... but, when I finished installation of the DSC module, 2 ports is not between these 3 serial ports. Before PRECAUTIONS, I can work with PLC and I can use other ports. After installation, I can't configure the serial ports... Hereby, I have attached the error with this...  Please help me soon...

  The Solution is, no need to install the VISA device drivers separately. Installing the DSC module only.

• EXTERNAL DELL PLACE 7 STORAGE PROBLEM

  I recently bought a dell 7 16GB place. And also I got a new sd micro for her card. Since im new to android, I think that when my internal memory is exhausted, the shaft of the BONE start mobile stuff on the sd card, but it has not tried to do it manually. I looked at a few tutorials on how to do it and all said you should have a function "move to sd card" when you go into settings > applications and select an application that you want to move to the sd card. But "move it to the sd card" was not there so I looked at a few other tutorials for 4.2.2 android JB and some said tutorials you need an app to do so I got "app 2 sd" and that does not work it gave me an error saying "the device is not a real primary external storage. ', or the main external storage is emulated "confused, I went to http://techgage.com/article/moving_your_non-movable_android_apps_to_an_sd_card/#comment-1189559025 and follow the tutorial here and it still didn't work! If someone can tell me how I can get "move to sd card" or is my tablet broken or is the fault of SD cards?

  Thank you!

  Thank you for the information. I tried half a dozen apps of type '2SDcard' as well as managers of file/apps half dozen that I downloaded from the Google game store. None of them admitted the SD card I had in my Dell place 8. And while that Dell 'Storage of parameters' showed that there was a 32 GB card where none of the apps I tried to found. And it's with my original Tablet and the "renovated" Tablet Dell sent me because they were unable to fix my original Tablet. So since it became clear that Dell would not help me with their product, I returned my Dell place 8 to Max of office for a full refund. So I guess I have to comment that: 1 Si Dell will provide a slot for SD card, why not provide the right software or hardware for use. 2. If all I had to do was install an application called "ES Explorer" why didn't not technology Dell tell me that? They are supposed to be the experts, not me. (As I don't have the Tablet I can't try your suggestion so don't know if the 13 app I have downloaded would work or not.) But I want to thank you. Your message has been more useful to me than the four different Dell Tech I spoke with.