Module problems

Similar Questions

• Download of modules problem

  I find the add-on I want, press 'Add to firefox', then the status bar instantly comes up with 'the module download' with the status bar complete with 0 bytes, then nothing! Don't see anywhere, its certainly not appearing is not in my extensions modules! I thought it was a problem with the wonderful Java but that seems to work ok... I think so?

  Help, please!

  Hello

  The reset Firefox feature can solve a lot of problems in restaurant Firefox to its State default factory while saving your bookmarks, history, passwords, cookies and other essential information.

  Note: After Firefox reset, you will lose all extensions, toolbar customizations, and certain preferences. See article Firefox Refresh - reset modules and parameters for more information.

  To reset Firefox:

  1. Open the troubleshooting information page using one of the following methods:
     • Click the menu button

       

       click Help

       

       and select troubleshooting information. Should open a new tab containing your troubleshooting information.

     • If you are unable to access the Help menu, type Subject: support in your address bar to bring up the troubleshooting information page.
  2. At the top right of the page, you should see a button that says "Reset Firefox" which looks like this:

     

     . Click on it.

  3. Firefox will close and reset. After it's done, Firefox will display a window with information that is imported.
  4. Click Finish and reopen Firefox.

  This corrects the problem? Please report to us!

  Thank you.

• Portege Z30 Module problem - A - 13 L 3 G

  I had a problem with a new Portege Z30 - A - 13 L.

  Module 3 G / 4G do not work. As a first step, the Air software map Watcher on the first Installation of Windows 7 detects the sim card and showed a signal, but it Air card Watcher Software still not said no reception (in German: Kein receipt).

  I also put the right apn in the profile.
  I had this problem with 2 different operators sim cards.

  Cause I wanted to use Windows 8.1 anyway I installed it with the original recovery disks.
  The original Windows 8.1 don t comes with Air card Watcher, so you must do with the instruments of the Board of Directors of Windows 8. Windows 8.1, I had a same problem. It detects the SIM, but it says no network (in German: Kein Netz). I put t found the possibility of changing the apn in 8.1 of Windows until you have a mobile connection.

  Initially the Device Manager displays the Module of Sierra Wireless EM 7305 as a network card.
  Then, I uninstalled the driver of Sierra Wireless and installed the Toshiba page.

  After that the Sierra Wireless Module presents itself as a Com device in Device Manager. The cause so much of this networker of Sierra Wireless adapter isn t it, the mobile broadband connection don t even shows charms Windows 8.1 bar upward.

  After that I reinstalled again the image Windows 8.1 with the original recovery disks.
  I saw said that Sierra Wireless Driver has been installed, but the Module EM7305 of Sierra Wireless is presented with an exclamation mark in Device Manager.

  Then I uninstalled and installed the driver manually again.
  He appears again as com device in Device Manager.

  So I think that the module has been a hardware failure. What do you think?

  > After that I reinstalled again the image Windows 8.1 with the original recovery disks.
  > I saw said that Sierra Wireless Driver has been installed, but the Module EM7305 of Sierra Wireless is presented with an exclamation mark in Device Manager.

  On the page of the Toshiba UE driver, you can find and download the [Sierra Wireless Driver LTE 4 G driver | http://www.toshiba.eu/innovation/download_driver_details.jsp?service=EU&selCategory = 2 & selFamily = 4 & selSeries = 362 & selProduct = 17549 & STAS hortMod = null & language = 13 & selOS = 46 & selType = all & year = upload & monthupload = & dayupload = & useDate = null & mode = allMachines & search = & action = search & macId = & country = a he's & selectedLanguage = 13 & type = all & page = 2 & ID = 90092 & OS ID = 46 & driverLanguage = 42]
  This Wireless Broadband Mobile driver is used to transfer data at higher rates and greater capacity.
  Install it!

  Also 3G must be activated before you try to establish a 3 G connection.
  Please check if the 3G module has been activated correctly!

  Recommend checking this information page of Microsoft Mobile Broadband end-to-end
  http://Windows.Microsoft.com/en-us/Windows-8/mobile-broadband-from-start-to-finish

  You will find different troubleshooting tips.

  In the case where you have a signal but you can't connect the possible reasons could be:
  You don t have a valid data subscription.
  The name of the access point (APN), user name or password used for the connection is not valid.
  You're roaming and the selected network operator doesn't allow data services or you don t have roaming enabled for data services.

• Tecra R10 - 10W / R10 - 111 3 G module problem

  Hello

  Module 3G does not work after the update. NA? find answers online. Maybe you know what to do:

  When I start the system from scratch, I just open the software Connect from Toshiba and the laptop connects after the network authentication. Usually after a certain time the yellow triangle with exclamation point appears and from that moment the system is connected limited/locally only. When I use vista tools to set up the problem I get the message that there could be a problem and I should connect via another network (lan, WiFi, BT, a? ¦) a? not really a solution to my problem!

  To restart the internet I need to disable the Toshiba g 3507 module and stop the wireless software Connect, wait about 10 seconds and then re-enable the module and restart wireless connect software. In fact, there is no option in the turn off the TPM in the wireless not connect software. When you work with my laptop, I need to reconnect it several times per day and this very annoying. Toshiba could not help me? They told me to call the hotline!

  I did all the updates that are provided by Toshiba, but it does not change.

  Any idea?

  See you soon
  Patrick

  Maybe the SIM card is loose, have you tried reinstalling the SIM card?

  Have you also updated the BIOS?

  Did you install any other software that may be contradictory? (For example, a USB 3 G external or similar device)

  Have you tried running the recovery to reinstall Windows.

  If it still does not work, then it might be a hardware problem, in which case you will have to send the laptop to an ASP for repair. The list of ASP can be found on the Toshiba site (the site of www.toshiba-europe.com assuming you're in EU)

• Placement of module problem

  Why, without real reason, sometimes modules not go where you want them to go on the worksheet?  Its like there is an invisible module there and can be placed here.  I find it rather annoying that I am trying to clean up a spreadsheet...

  Thanks for any help I can get!

  John

  Hi John,.

  We also got your request for support of www.dasylab.com, and I've left a voice message and sent an email this morning.

  There is a long-standing problem where some places on activities will be marked as used, even if there is nothing in this place. Usually, we see the problem in a worksheet that has been addressed in several versions of the software, or has been edited heavily, especially moving the modules and son, over a period of time.

  If you will send me the spreadsheet with the problem, I can watch them and possibly fix them.

• Firmware for the F348XP - N77 - 23 Nexus module problems

  H,

  I hope you had great Christmas time! I am currently working on the new Nexus lab, and I have a challenge.

  I try to get 1/10 Gbit / s Ethernet Module running. Do you know where to find firmware for this module and how to set the variable initialization for her? What I get so far:

  introduce the module:

  Status of Module Type mod Ports model
  --- ----- ----------------------------------- ------------------ ----------
  1 48 1/10 Gbit / s Ethernet Module N77 - F348XP - 23 ok
  2 48 1/10 Gbit / s Ethernet Module N77 - F348XP - 23 powered-dn! This one, with that I'll have the problem
  3 0 active supervisor Module-2 N77-SUP2E *.
  4 0 supervisor Module-2 N77-SUP2E ha-standby

  When I try to turn it on by entering

  (config) # No module poweroff 2

  I'm more about newspapers:

  2015 Dec 16 00:38:23 % xxx platform-2-MOD_DETECT: Module detected 2 (serial number JAE19290A6J) Type of Module-1/10 Gbps Ethernet Module model N77-F348XP-23
  2015 Dec 16 00:38:23 % xxx platform-2-MOD_PWRUP: Module 2 under voltage (serial number JAE19290A6J)
  2015 Dec 16 00:38:23 % xxx platform - 5 - module MOD_STATUS: Module 2 - current situation is MOD_STATUS_POWERED_UP
  2015 Dec 16 00:40:02 xxx % BIOS_DAEMON-SLOT2-5-BIOS_DAEMON_LC_PRI_BOOT: System started from the main BIOS Flash
  2015 Dec 16 00:40:05 xxx % FW_APP-SLOT2-2-FIRMWARE_IMAGE_LOAD_ERROR: error extraction and loading Firmware: firmware Flash and software images are bad
  2015 Dec 16 00:40:06 xxx % MODULE-2-MOD_FAIL: initialization of the module 2 (serial number: JAE19290A6J) failed
  2015 Dec 16 00:40:06 xxx last message repeated 1 time
  2015 Dec 16 00:40:06 xxx % PLATFORM-2-MOD_PWRDN: Module 2 power off (serial number JAE19290A6J)
  2015 Dec 16 00:40:06 xxx % PLATFORM-5-module MOD_STATUS: Module 2 - current situation is MOD_STATUS_CONFIGPOWERED_DOWN
  2015 Dec 16 00:40:06 xxx % PLATFORM-5-module MOD_STATUS: Module 2 - current situation is MOD_STATUS_POWERED_DOWN

  I take the problem is with the firmware, but I can't find the path to it. It there is no defined variable initialization is module 1, or 2, but module 1 started without problem.

  XXX # display the start module 1
  No set variable initialization module
  XXX # display the start module 2
  No set variable initialization module

  I can see the bin files under
  XXX # cd bootflash://module-4/
  bootflash://module-4/20150808_221923_poap_7580_init.log bootflash://module-4/vdc_3
  bootflash://module-4/20151211_010151_poap_8037_init.log bootflash://module-4/vdc_4
  bootflash://module-4/20151211_015441_poap_7723_init.log bootflash://module-4/vdc_5
  bootflash://module-4/lost+found bootflash://module-4/vdc_6
  bootflash://module-4/N7700-S2-dk9.6.2.12.bin bootflash://module-4/vdc_7
  bootflash://module-4/N7700-S2-kickstart.6.2.12.bin bootflash://module-4/vdc_8
  bootflash://module-4/scripts bootflash://module-4/vdc_9
  bootflash://module-4/vdc_2

  but I'm not able to assign variable initialization module, I see 1 - sup and sup - 2 only

  XXX (config) # boot system bootflash://module-4/n7700-s2-dk9.6.2.12.bin?
  
  SUP-1 input sup-1 to set up the 1st sup
  SUP-2 input sup-2 to set up the 2nd sup

  I hope that you would be able to help!

  Happ new year as well! :)

  Hello

  Do you have these linecards at the same time? I see that module 1 is the same model and do not have any problems. Did you open a SR of TAC for the same thing? I saw some similar cases where these messages could be the result of a faulty hardware, but you can open a folder of TAC to continue the investigation.

  HTH,

  Wes

• Link to the Gallery module problem

  I have a photo gallery module on http://grapeleafcafeandgrill.BusinessCatalyst.com/Gallery.html links low on the right do not run properly. Can someone please help me with this?

  I am answering my own post. Please do not take into account. I was in a bootstrap carousel to solve my problem.

• CC 2014 on iMac 2011 - video Module problem

  I just installed the first Pro 2014 CC version on my iMac and now get this message.  Error "Premiere Pro could not find capable video game modules"

  Self-service on the Adobe site support is insufficient, fails to provide valuable support.

  Does anyone have the same problem with this version and, if so, the indices on fixing it, without having to buy a new Mac?  And Yes, I have 2 GB on the GPU, 32 GB of RAM.

  Hi NCMUK,

  Try this:

  • Go to the following locations and rename the folders "old_folder Name" (like old_Adobe)
    • User/user/library/Application Support and rename the Adobe folder.
    • User/Library/Preferences and rename the Adobe folder.
    • Navigate to the Documents folder then to Adobe/Premiere pro/8.0 and rename the 8.0 folder.

  Thank you
  Kevin

• Tecra R10 - 10W / R10 - 111 3 G module problem see also messages from May 25

  Thanks for your fast replay.

  Yes, I have tried to reinstall the SIM card and updated everything what is possible from the homepage, Microsoft and Toshiba. No external devices (e.g. 3 G USB) installed and windows is retrieved by a full licensed Windows Vista Business (No. Toshiba OEM more) just a couple of days.

  The only thing I discovered is that the 3G module Firmware is not updated. I didn't recognize the pop-up window when before updating, but yesterday, I got the day when/after massage:

  "Generation data has not changed, probably failed update"

  I tried to update with an activated, a connected and a module 3G disabled (in that order) but no change. I always get the same message once the module is restarted during the FW update. The module was not disconneced by stopping the system or any other stop option during update FW (as read in the instructions). The old FW was working fine until I did some updates to the Toshiba homepage (always ask Tempro). Any idea?

  Control on while you try to update the firmware with the original image of Windows from Toshiba?

  Where did you got the firmware?

• Input RS232 module problem

  Hi all

  I am trying to read and save data to an account with DASYLab.

  DASYLab and the Windows Device Manager to detect the right COM port, although sometimes I can't see the port connected to the command prompt (using the 'mode' command).

  Everything seems fine, but I don't get all the data in the RS232 input channel.

  I tried to follow the module interface while asking data (using 2WOW\f), but without success!

  I appreciate your help and your suggestions.

  
  

• serial port after the installed DSC module problem

  Hello..

  I want to GSM(with labVIEW) and PLC interface, My PLC will work in serial port only.

  In my PC, I have 3 serial ports. before installing the DSC module in my system, I can configure the ports series all the... but, when I finished installation of the DSC module, 2 ports is not between these 3 serial ports. Before PRECAUTIONS, I can work with PLC and I can use other ports. After installation, I can't configure the serial ports... Hereby, I have attached the error with this...  Please help me soon...

  The Solution is, no need to install the VISA device drivers separately. Installing the DSC module only.

• Lightroom Develop module problem

  Hey guys,.

  I recently moved the trial version of lightroom cc. After you've imported with success images, when I go in the develop module, I don't see my image I imported, instead I see a large cross on the area where the image should be displayed. Kindly help me. I use a lenovo computer s510p laptop i5 processor, 8 GB of ram. Kindly help me.

  Go in Edition > Preferences > Performance and uncheck CPU graph use.

• Develop the module problem after upgrade to LR6

  I upgraded from LR4.4 to 6, but had made a stop at 5.7 on the way. I have improved the catalog to v5.  Now in LR6, that I bought at the end of the day, photos in the develop module are corrupt. I can see them but are mainly grey with a few colourful highlights. Don't know if it's a question of catalog or how to fix. All files seem to be affected!

  Hi cruizemissile,

  Please turn off the graphics processor in the Lightroom preferences.

  Open Lightroom

  Go to Lightroom preferences in the Edit menu

  Click the performance tab

  Deselect the graphics processor

  Restart Lightroom

  Let us know if that helps.

  Kind regards

  Mohit

• Develop the Module problem

  I use LR since May 13. Initially, I used LR4, then upgraded to 5 on my iMac. A few days ago, when you use the development Module, the right side of the screen is missing. On the right are the tools and panels for setting global and local photo. Went. I tried to the control key to develop at the top of the screen. Nothing changes. Can anyone help?

  Press the TAB key?

  Frans

• Card Module problem

  I used LR4 for the first time to geotag my photos, after previously using GeoSetter. Although the process was not as smooth as Geosetter, we'll later. The problem I have now is that the city, State, secondary, etc. subject to the operation of geolocation appears in the pane metadata in italics (while the photos previously geotagged using Geosetter are not put in italics), and even would not a problem, except that when I set the display options for the library (Ctrl-J) to show the secondary location in the cells of the grid in the upper right position the secondary does not appear. The geotagged photos via Geosetter do not have this problem, the secondary appears. Sample photo geotagged via LR 4, upper right position of informationp does not show the secondary:

  

  Photo geotagged by GeoSetter, right position top of cell information page shows secondary

  

  Can I fix this, or is this a bug?

  Paige,

  The location italic/gray fields correspond to the "uncommitted" geoencoding data the other way round. As uncommitted same data are shown in the metadata filter, I would call the display missing a bug in the grid cells.

  There are a full thread on geoencoding reverse and validation of data somewhere here. You can validate the data by clicking on the title of the field and make permanent content.

  Beat