Placement of WLAN Interface 5508

Similar Questions

• M40-154 satellite WLAN interface does not send a single packet

  Hello

  I own a Toshiba M40-154 with built-in Intel PRO/Wireless 2200BG Network Chipset. I am running Windows XP Professional Service Pack 2. 9.0.1.9 driver version.

  The Windows hardware Manager shows no conflict about resources memory, interruptions or anything else, just said me eth. would be nice (.. .and Yes, I changed the WLAN switch in front of the box to 'on')

  I configured both Wireless-Lan, once using the Toshiba and Windows XP itself once.

  Wireless networks are recognized, but I can't make any connection. It seems kind of strange to me, because when sniffing Interface with Ethereal, lie, not a single packet is sent by my WLAN interface. I checked all the configuration on another laptop with the same chipset and just works well.

  After the first installation of Win XP, I had a similar problem with my Marvel Yukon LAN interface. He comes to recognize connectivity (even LED a cover connectivity) but not sent or received a single package. I could only get rid of this feature by installing the device drivers located sequentially.

  When you run the diagnostic tool for Toshiba it tells me just the network test "fails". I m really get angry with this tool to completely unnecessary IMHO, because she neither doesn´t made the distinction between my work correctly Marvel Yukon LAN and WIFI, nor give me any hint, what could be the problem...

  Anyone with similar problems or able to give me a clue?

  [Edited by: admin August 10 05 19:33]

  Hello

  I'm really confused. Last week I set up the Satellite M40 and WLAN network by a friend of mine. His unit is pre-installed with recovery DVDs and everything works fine.

  Have you had problems at the beginning or just after installing WXP professional? I put t know how you installed the operating system, but I hope that you used the instructions to facilities provided by Toshiba. The order of the facilities is very important.

  If the WIFI network is visible in my opinion there must be a problem with the WLAN settings. Your WLAN is locked with a WEP key? Try to establish a connection without restriction.

  I hope that your access point is just configured and type of PPPoE. In this case the IP address must be the value automatically.

  Sorry, but on this path, it is really not easy to say what may be the problem.

  Good bye

• Recover the forgotten password already created WLAN in 5508 WLC

  Hello

  Is it possible that we can retrieve the forgotten password already created WLAN in 5508 WLC. I do not want to reset the password want to only see the existing password. Image is attached as a reference.

  Kind regards

  Muhammad Noman

  Hi Muhammad,

  I don't think that it is possible that the key is encrypted in the configuration files as well.

  See you soon,.

  Ric

• IDS 4215, good place for an interface sniff (LAN or DMZ)

  I have this sensor with two interfaces only at work, I was asked to check that

  See the IDSWORK version #.

  Application partition:

  The Cisco Systems Version 1.0000 S47 Intrusion detection sensor

  2.4.18 - 5smpbigphys-4215 OS version

  Platform: IDS-4215

  an interface that is Ethernet 0 connected to switch in the DMZ, and 1 Ethernet connected to switch 4005, logically I have to monitor DMZ not switch box 4005 (since I had only two interfaces, my case), I'm right?

  That means that ethernet 0 should be to sniff (surveillance) since it is connected to the DMZ and interface 1 for command and control, since it is connected to switch 4005, but according to cisco specifications

  http://Cisco.com/en/us/products/HW/vpndevc/PS4077/products_configuration_guide_chapter09186a008055df7d.html#wp1051279

  Table 5-2

  FastEthernet0/0: Interfaces supporting VLAN pairs Inline (port detection)

  FastEthernet0/1: Interfaces do not support Inline (command and control Port)

  Note: Cisco has mentioned FastEthernet, one I had Ethernet, makes all the difference?

  Because I did not have this configuration, he made by another, should I change this?

  It seems that your credentials are equipped with the basic ports (2 x Ethernet) with E0 C & C port, while E1 is followed by port.

  BTW, Ethernet/FastEthernet ports are in fact the same.

  To monitor your DMZ segment, then place the E1 in this segment, as E0 on inside segment where in addition to directing the Manager of its web management or CLI interface box, you probably can use basic VMS that comes free with it.

  And since you have dedicated switch to host the entire DMZ segment, you can easily monitor box (SPAN) all and send all traffic to the IDS.

  If you need to change the configuration, you may need to test at least to verify signatures is enabled/disabled and pc/mgt host is allowed to access the box and so on. But it is a good practice for audit and review the new config/setup, as it is a security zone, you need to do to monitor trust and you talk about all the possible threats, attacks or violations.

  HTH

  AK

• Problem with NAC and 5508 WLC OOB

  I have a wlc 5508 to shared resources to a 6500 switch. Shared resources to the switch on eth0 and eth1 is also the CASE. The CAM is connected to an access port.

  The SCS and CAM are on VLANS separated and the CASE has been added to the CAM without problem.

  I followed the example of document for OOB WLAN (VLANs and mapping etc.), but I don't get all current identifications. The client is associated and the WLAN interface is the quarantine VLAN but it seems that the client can connect to the network without problem (may web access a server in-house to campus)

  The customer indicated in customers wireless on the device of the cam page

  If I either CASE interfaces close client connectivity is broken.

  Once, randomly the own access connection Page appeared on the client (battery dead and waited for about an hour) but when I rebooted the CASE check it was she never came back.

  I do not set up the SSO part, must it be filled or is it a valid test without it so far?

  No idea where to start with this problem?

  Thank you

  Yes, it looks like that somewhere, your 'placing in quarantine/no authenticated' vlan is filled to the full network, I do not see another explanation.

  Try to configure the WLC for a new vlan quarantine which does not exist anywhere.

  Then you should not have any access at all to anything whatsoever. Then try to leave this vlan gradually reach the heap and constantly test. You should find the point where the vlan 'flows '.

  Nicolas

  ===

  Remember responses of the rate that you find useful

• Trying to figure out a mooring - WLAN reviews

  We have six controllers among three main campuses and two remote sites. I set up a WLAN guest at our main location on two of our controllers (we have two controllers for our main campus)

  I would like to set up my other controllers so that a user can connect to the WLAN guest and their traffic is sent to my main controllers, this way they get to the intellectual property in the VLAN of my main controllers. It seems that mobility anchors are my answer but I find it very confusing.

  For me, it looks that I create a new WLAN to my remote controls, go to the advance tab and choose mobility anchors and select my two PDCs I want my traffic to go to. But to set up a WLAN, I need to create an interface and VLAN to place the WLAN on.

  Or is my thought full backward and I had to go to my main controllers, go towards mobility anchors and choose my remotes from there. My main controllers will then configure my remotes for the SSID. I can't do a lot of testing because it is a production system that needs to change management and it is difficult to test a remote site.

  All my controllers are in the same group of mobility

  Well, since you have all the same mobility group controllers, you are almost finished.

  Create the ssid of comments on the other exatly the same as controller (s) in the main campus. The only difference will be that the interface you'll be assing the ssid on the other wlc is management. Then select on the ssid on the blue icon, anchor of mobility. This will bring you to a different screen... you will choose the ip address of the wlc two in the main campus... one at a time and choose Create mobility anchor.

  That should do it...

• 5508 WLC works only with small business unit SA 520 security

  Cisco 5508 is new Wireless LAN Controller supporting 802.11ac new Giga bit wireless. It has been connected to the port of SA 520 LAN LAN port of small business Security Appliance (trunk). VLAN by default 1 works fine, which is for the management but vlan data does not work.

  However, I can ping from WLC until SA 520 on vlan data but no ping SA 520. Also the wireless clients connected to the AP cannot connect to SA 520 on the data vlan 2702 as gateway?

  both have the latest firmwares. These devices are supported?

  Any suggestion?

  Hello

  I guess your VLAN DATA is another VIRTUAL local network that you have configured on the WLC.

  Make sure of the ff.
  1. you have configured the correct WLAN interface
  2. you have assigned the right WLAN interface on your SSID
  3. the DHCP of your users (where btw?) if in the WLC, check if it is on the correct subnet and that it is enabled

  Also considering it is a safety device, check that the ff:
  1. you have configured the necessary policies and fro the AP and WLC
  -Note that traffic CAPWAP able, to avoid any problem, just allow and fro WLC and AP for example, two policies a WLC-> AP and another AP-> WLC

  2. of course, the policies necessary to allow traffic

  PS: The compatibility is not a problem, note that your servers SMB of device as a connection of the WLC. You should have no problem integrating the two

  If it is not much, kindly rate helpful messages :)

• 6.26.84 - all network interfaces access connections are missing

  Yesterday I ran the 5.7.29 system update on my W520 running Win7 (64 bit). Install you 3 updates optional incl. Access 6.26.84 connections.

  Today, I noticed that:

  -connections to access the icon status indicates that the LAN interface is disconnected when it is connected and works well

  -Fn + F5 will no longer display the WLAN interface

  -the program of connections to access display a gray button export under location and profiles the following error under Advanced-> tools-> Diagnostics:

  Connection status: not connected
  Cause: Card not found.
  Error code: 006

  At this point, I'm looking for a solution for:

  - either get logins 6.26.84 works correctly (so that I can turn my WLAN using Fn + F5 interface)

  -or export/save my location profiles before uninstalling the access 6.26.84 connections (so that I can import it during the installation of dial-up connections to 6.26.82 once again)

  I had the same problem after you install the 6.26.84 update. WiFi worked well when a known network was available but I couldn't influence anything. All parameters were out of service. I have spent a few hours to update several drivers - but without success. Finally, I went back to the 6.26.82 version and everything worked immediately well.

  During the uninstallation of 6.26.84 there is the possibility to save all the individual settings. Unfortunately I chose "no" - so I had to start from scratch...

• Elitepad 900 Windows 8.1 WLAN problem

  I have several Elitepad 900, model number is D4T16AA.

  Recently ugpraded to Windows 8.1 Enterprise using Microsoft Enterprise Agreement media, works as a full clean install (not an upgrade on the spot). All updates to existing Windows were then applied on top.

  Now the WLAN has stopped working. The WLAN interface seems to be upward, but it says 'No networks detected' - of course, there are networks on the site: at least four of us, as well as a few edge com the roundabout.

  I installed the latest driver from the support site (SP64649 that's as far as I know - correct me if I'm wrong). No joy.

  I found this article: http://www.shcherbyna.com/?p=2113 and I downloaded and tried all the older versions of the driver mentioned here - SP60450, SP60664, SP60901, SP61232. In any case, I uninstalled the device, rebooted, installed the old driver and restarted. In all cases, the results were the same - 'no network not found. '

  Please can someone confirm what version of the driver will actually work in this machine?

  I lose a lot of time trying different things, surely it should "work", WLAN is no longer rocket science.

  Thanks in advance.

  I see that you have already tried a lot of possibilities, but I would suggest a few steps:
  (See victory unity 8.1, 32-bit)
  1: Please uninstall the wireless completely from the device driver, restart the device and update driver wireless sp64649 using link below:
  http://h20566.www2.hp.com/portal/site/hpsc/template.PAGE/public/psi/swdDetails/?sp4ts.oid=5298035&spf_p.tpst=swdMain&spf_p.prp_swdMain=wsrp-navigationalState%3Didx%253D%257CswItem%253Dob_127781_1%257CswEnvOID%253D4157%257CitemLocale%253D%257CswLang%253D%257Cmode%253D%257Caction%253DdriverDocument&javax.portlet.begCacheTok=com.vignette.cachetoken&javax.portlet.endCacheTok=com.vignette.cachetoken
  
  2: Please download the latest "BIOS settings" using link below:
  http://h20566.www2.hp.com/portal/site/hpsc/template.PAGE/public/psi/swdDetails/?sp4ts.oid=5298035&spf_p.tpst=swdMain&spf_p.prp_swdMain=wsrp-navigationalState%3Didx%253D%257CswItem%253Dob_127435_1%257CswEnvOID%253D4157%257CitemLocale%253D%257CswLang%253D%257Cmode%253D%257Caction%253DdriverDocument&javax.portlet.begCacheTok=com.vignette.cachetoken&javax.portlet.endCacheTok=com.vignette.cachetoken
  
  3: Please restore default BIOS.
  
  4: If above steps do not solve the problem, it could be a faulty itself WLAN card
  
  Although I am an employee of HP, I speak for myself and not for HP.
  
  -Say 'Thank you' by clicking on the star of congratulations in the post helped you.
  -Please indicate the position that solved your problem as "acceptable Solution".

• WRT54G v3.1 (firmware v4.21.1) is not route packets between interfaces

  I am at a loss, because it seems that I'm really close to having my small network of installation works, except my router linksys faithful does not seem to be interested in packages of brewing between the WAN and WLAN interfaces.

  Background:

  I just moved into a new House, AT & T U-verse is taking their sweet time thought of digging a trench, so I have no wired internet, but I have a phone with 4G support that I can use as a hotspot Wi - Fi (high-end and very limited functionality).

  My goal is to rebuild my local network (two servers by cable, half a dozen various wireless devices), using my WRT54G as the central routing for her component.

  Plan:

  1. install a wireless bridge that connects to the Wifi 4 G hotspot.

  2. connect ZyXel bridge to the WAN port on the WRT54G

  3. connect and other devices in LAN WRT54G and wireless interfaces.

  Results:

  1. I got a ZyXel WAP3205 to this effect, and it seems to work fine (when connected to PC, PC is to get internet access through it perfectly.)

  2 seems to work fine. the linksys router is able to obtain an IP address on DHCP 4G Wifi hotspot (the Zyxel will exercise a passthrough.) The admin/diagnosis tab let me DNS resolve/ping/traceroute arbitrary sites on the internet.

  3 is not happy. I am able to access the router admin page. I can ping the router from any of my devices to end IP addresses, but nothing goes further. I can not ping IP of 4G Wifi hotspot for example (but I do go in the WRT diagnostic tools)

  Details of config:

  -4G - Wifi hotspot is configured as a DHCP/Gateway server. His IP address is defined as 10.10.10.1, subnet 255.255.255.0, assignment of IP addresses between 10.10.10.2 - 10.10.10.254

  -WRT router is configured as a DHCP/Gateway server as well. Its local IP address is set as 192.168.1.1, subnet 255.255.255.0, IPs assignments between 192.168.1.2 - 192.168.1.51.

  -All the rest is to default settings. Mode of operation is the gateway, routing table is showing

  Destination LAN IP.  Subnet mask |  Entry door |  Hop count | Interface

  192.168.1.0. 255.255.255.0. 0.0.0.0. 0           | Wireless LAN &

  10.10.10.0 | 255.255.255.0. 0.0.0.0. 0           | WAN (Internet)

  0.0.0.0             | 0.0.0.0. 10.10.10.1. 0           | WAN (Internet)

  This seems reasonable.

  -Status/router tab displays an IP WAN address 10.10.10.172, subnet 255.255.255.0, gateway 10.10.10.1, DNS1 10.10.10.1, which looks very good as well.

  I tried to adjust various settings on the router (gateway in router mode switching, disable DHCP and manually configure IP addresses), but nothing seems to convince the router to start, you know, routing of packets autour.

  I hope I'm missing something stupid here, and I'll be grateful for any help and judgment on this.

  Thank you

  Henri

  * Edit: I should add, I use this little guy for years previous houses, and it has always worked, even if its WAN port was always plugged into a modem cable of some sort. So I don't think that the WRT54G is likely to be broken or defective.

  Sonuva...

  Apparently, the little box just need a fast walk. After a factory reset and set my wireless settings screw, it seems to work perfectly.

  Well, I think that I'm talking to myself now.

  Just for fun, here is the great link, I'll be sharing between devices 8 or 9:

  

  (which is through my whole setup, even if the speed is exactly the same thing with a direct link.)

• WLC5508 problem with dhcp and flexconnect local switching

  Hello
  I have a new WLC 5508 with firmware 8.0.133.0 (suggested one right now) and I'm trying to set up a WLAN with flexconnect and local switching, but when I try to connect a client it is not getting an IP address.

  Here's what I did:
  -put the AP mode flexconnect
  -support vlan in the AP has allowed
  -local switching license and only in wlan
  -spread the vlan from AP to the local gateway
  -put the IP helper on local and pointed the wlc management ip gateway
  -set up a scope for the vlan Server dhcp internal WLC
  -set up a working group with the vlan-wlan association flexconnect

  Here is what I checked:
  -l'AP obtains an IP address in dhcp in the vlan, and a lease for that appear in the DHCP Server internal to the WLC
  -If I put the interface vlan on a switch in DHCP it gets the ip address of the same way
  -If I set the static IP address in the wireless client it ping the local gateway and navigate normally
  -J' tried the deactivation/activation proxy DHCP in the management connected to the WLAN interface, but nothing happened
  -J' tried Central DHCP activation of treatment with no luck

  It seems a dhcpdump on the wireless client client ask for an IP address, but get no response, as if it were the DHCP request is be filtered or diverted somehow.

  All you other ideas?

  DHCP on the controller is not a real dhcp server, see it that way. The management interface is used when defining aid ip and proxy dhcp must be enabled for internal dhcp. In your configuration, dhcp only works for the AP and should not work for any cable customer. You should be able to use the IP helper pointing to your WLC management interface but also make sure that you create an interface on the WLC for the local subnet and assign the interface to a correct address, even if it is not actually using it. Then in the new dynamic interface of this local subnet, you create, make sure that the primary dhcp is the ip address of the controller management. I think it works.

  I would really use a true if possible dhcp server or even put a dhcp scope on the interface of L3 on the production site.

  -Scott

  Please evaluate the useful messages *.

• redirect Web does not work on WLC5508

  Hello, please I have configured WLC 5508 to support comments VLANs mapped to virtual and associated with guest ssid wlan interface.

  on ssid comments I enable L3 security with web policy. authentication and passtrought does'nt refirect web page for authentication.

  I can get dhcp DHCP param trought pool for the vlan correct comments.

  additional information: I see that the control sending a bad ip address redirection.

  WLC management interface is 10.7.1.10 and I saw 10.7.4.10. I remember that this last ip was intended, such as adding the ip of the dns server, but I don't see where I can change it?

  the IP dns configured on the pool is 10.7.1.10.

  Please any idea for this problem?

  Apart from the question of Surendra, I think your config looks totally bad :-)

  You say just the DNS in IP pool is the WLC management interface. Which makes no sense and will prevent webauth to work normally.

  You also say that you attach your comments interface to the virtual ip address? Why is this?

  I think it would help if you post a 'run-config show' of your WLC so we can check for errors.

  Nicolas

• Qosmio PX30T - Bluetooth mouse has stopped working

  I was able to reactivate Bluetooth on my PX30T after having changed the batteries in my Bluetooth mouse. (Sorry Toshiba, your standard mouse is uncomfortable!). Not sure if the circumstances leading to it as my son noticed the battery do not and then changed the batteries.

  I have gone into arrangements and have looked everywhere and not see compatible Bluetooth (or even a switch to do). I have no more Bluetooth icon in my taskbar. The only clue that there is in the mouse settings, but it won't let me uninstall it either.

  Other than a reset full... any ideas?

  Are you sure that it is a BT mouse?
  The manual indicates that the keyboard and wireless mouse are connected to the all-in-one computer! I recommend the user manual.

  Usually the keyboard and wireless mouse may be detected by computer automatically.
  But in case that does not work, you may need to match the WLan keyboard and mouse.

  (1) turn on the computer
  (2) press and hold the middle mouse button
  (3) slice the power that, in the back of the mouse on the market
  (4) the battery indicator starts flashing to indicate that the mouse is ready to be paired
  (5) keep the mouse near the bottom right of the computer within 10 cm place the WLan receiver
  (6) the battery indicator lights up for about 5 seconds if the pairing is successful

  the connection will be established then

• Satellite A200 - 14 d is unresponsive to the netsh command

  Command netsh wlan show settings + represents the name of the wlan interface on which MS windows network autoconfiguration is enabled.

  When I type set autoconfig enabled = no interface = "NameInterface" + nothing happens. The first command shows that autoconfig is always activated.

  What's wrong? What is the real "NameInterface" for A200 - 14 d with Vist Home Premuim?

  I really put t know why, you must define that but maybe you have to have a look on this Vista Microsoft Windows TechCenter for more information on Netsh commands for Local network

  http://TechNet.Microsoft.com/en-us/windowsvista/aa905084.aspx

• WIFI works only under Windows XP on Satellite U400

  After the installation of Windows XP on my WLAN the U400 recovery is not found. It was working correctly under Win Vista.
  There is no module listed in Device Manager - once the new hardware search gave no results. It seems that the WLAN Interface is not recognized by Win XP.

  The Communication switch at the front was 'ON' - bluetooth works properly.

  It's amazing to me usually the XP should see and recognize the device inserted as an unknown device, if a driver has not been installed.

  But you're right. It looks like the U400 should be equipped with the Realtek 802.11(b/g) 13ch-RTL8187B Wlan card

  Have you tried the driver from the Web to Realtek site?