Please help the gurus of the OFA - problem solved.

Similar Questions

• Do you have the wifi problem solved TP?

  I'm a Chinese TP user, my English is not very good.

  My TP (16g, webos3.02) can connect to wifi but cannot connect to the internet. I think many users have the same problem and if anyone has resolved, please show me! Thank you

  Yes, Yes, Yes.

  And I solved it today! She caused by two questions!

  'No Internet connection' caused by the router setting band. I put the tape from 'auto' to '3', then change of the error 'Connection no Internet' to 'Unable to resolve host. " So I changed the DNS to 8.8.8.8 manually.  Now, everything is ok! I hope you understand my bad English

• I accidentally deleted the setting wireless network connection icon, please help the change adapter

  I have Toshiba satellite A 505 S6989

  I accidentally deleted "Wireless Network Connection" icon of "changing the adapter setting" (network & sharing Center) while she was to allow...

  I have driver installed several times but he forces back...
  Also checked... but under the network adapter, Device Manager is showing only realtek ethernet... no wifi

  Please tell us how to get back this icon so that I can connect via wifi...

  Please answer as soon as possible
  concerning
  Afonso

  I solved the problem a few days before, sorry for the late response...

  WiFi card was detached from this place (it was a hardware issue)

  I opened my laptop and re placed this wifi card.

  now it works fine

  Thank you

• Please help, the printer does not have 'ink system failure '.

  Hello

  Any help appreciated.  My printer is printer all-in-one Photosmart C7280.

  2 days ago my printer has not worked. It comes with several error messages after I turn it on. The first is "ink system failure: ink system has failed." Cannot copy, receive faxes or print. Refer to the printer documentation. Error: 0xc19a0025. Turn off the power, then new. »

  However when I turn off and then again via the "power" button, I get a message saying "abnormal termination. Then the same error message original returns (0xc19a0025). It is the most common error and won't go away. Then too, I get a message saying "problem Photo tray: lift the output tray, check the photo tray is pushed up to the stop, lower output tray. Despite the fact that I haven't used the photo tray in several months and it is in the correct position.

  So far I tried to turn on the printer, shut down several times by using the power button. Also, I turned off the printer in making last night (after having been closed properly) and back on this morning. I looked through the documentation of the printer, but could not find tips for troubleshooting for this kind of problem. I updated the driver from HP using software update on my mac, and the problem is still there.

  Now I get desperate, I rely on my printer/scanner/copier a lot!

  Thank you

  Nathalie

  This widget could not be displayed.

• Please help, the TrojanSpy: Win32 / Delf was only PARTIALLY removed by the Microsoft Safety Scanner

  October 6, 2012

  Hi all!

  I ran the Scanner Microsoft (MSS) mode Quick Scan and it found nothing.

  I then ran MSS in full Scan mode and it found: TrojanSpy: Win32 / Delf

  In the results of Scan of MSS window, he says:

  "The analysis is completed with success and viruses, spyware and other potentially unwanted software were detected and partially removed".

  Given that the results showed the presence of "TrojanSpy: Win32 / Delf" I have four questions, please:

  (1) how do I get this Trojan horse on my computer? I am very sure and use a good anti-virus/malware software.

  (2) given that the results showed only partially removed SMS "TrojanSpy: Win32 / Delf", that the parts are on my computer?

  (3) how dangerous is the part or parts that remain on my computer that SSM has not deleted?

  (4) how to remove somewhere has been left more that SSM has not deleted?

  Thank you in advance for any help that anyone can give me.

  Sincerely,

  Traveler4God

  Hello

  Yes, it will remove the infection.

• Please help the issue

  I am new to FW and decide. I tried to get all the info of tutorials and help I could. I'm still confused. I am producing a model of Web site page multi with FW exporting CSS and Images.

  I submitted two other crossings with 0 replies. I guess that my questions were too broad? I did some trial and error and tried testing with a simplified version of the model of the multi page site that I am producing. See simplified here:

  http://www.openrangeimaging.com/test-posts/slicetest01.PNG

  The upper area would be the header. The bottom bar will have some nav tabs. The circle must be a logo which if clicked on will take the user to the home page... Below value nav bar is two columns with the content.

  I've tried different ways of slicing cela but cannot get the file to correctly export as CSS and Images. I also can't seem to include the logo as a slice with a link without having the problem of "overlap". I have beaten myself against that for some time and have had no success. Any help or advice on where to get help or an answer at all will be most appreciated. Thank you!

  Great, my message as a whole was wiped out. Here it is again:

  My comments are in line.

  14-10 - 2010 at 02:16, markf12 wrote:

  Jim, thank you very much for your very helpful answer!

  Honestly, I try even to directly export this FW design to a CSS based formatting. I think I would spend much more quickly by exporting FW graphics and design development in DW.

  That's what I needed to know. Being new FW I'm wrong assuming that I could use the Images and CSS to export a clicklable model which could serve as a basic html/css site 15 page I design. I thought it was possible, if only I could figure out how. I expect that a pretty involved job in Dreamweaver would be necessary. Now I understand that for what I'm using the HTML code and Images of the practice is what should be used. Then I develop the site in Dreamweaver using the perhaps some images exported from the model of the FW, but no html or css. Thanks for clearing that for me! I knew I had a fundamental misunderstanding / kernel. Export of Images and CSS is only for a very simple design.

  JB - it IS possible, but you need to design the site according to certain practices. The slices overlap is something to avoid.

  . If you are new to Fireworks, you really want to keep things simple, you will learn the process. Nevertheless, a good knowledge of HTML and CSS is very important.

  Yes, I like to keep things simple, but it's a bit of a trial by fire (pun intended) on a project. I got books and other html and css tutorial type stuff. I wouldn't say my knowledge of this solid as I am new to it. I think that most it and I am determined to become proficient. The only real way to do that is to create something of real / have to start somewhere so...

  JB - get the 'essential' is not enough. If you do not have a strong background in HTML and CSS, you will probably run trouble even IF you export successfully design, because you will have to edit and modify the code once you're in DW. I would recommend your first construction sites "the old-fashioned way" first, before trying to automate the process.

  David Hogue has created a great series of videos of export CSS on the Dev Center of fireworks. I highly recommend watching. Similarly, Michel Bozgounov wrote a great article on creating a Fireworks document for export CSS:

  I had seen a number of tutorials from Dave H. I have somehow forgotten those you provided a link to. I'm watching right now. I had read the Article of Michel B. also excellent. I also read your excellent tutorials and watched your lynda.com training video. I got allot of things.

  Thanks again for your help!

  JB - you are the very welcome. Good luck.

• The OFA problem

  Hi experts,
  
  I have a requirement ofa...
  
  I'm working on the employee self-service-> profile-> add skills-> find-> skills before press the GO button by choose YES in GLOBAL down to the bottom of the list-> show all the skills.
  
  The requirement is that only of skills must be displayed
  Skills should not be displayed.
  Skills, differentiated based on Attribute1 column in the Per_competences table.
  If Attribute1 - Yes means that it is a skill
  If Attribute1 - no way it's jurisdiction.
  Only Attribute1 value - yes column should appear.
  
  Please give me valuable advise for me...
  
  Thanks in advance

  Hi Alain

  Skills/competence is a FDF column

  Thank you

  Kind regards
  Vlaminck

• ISO Windows7 upgrade of my system XP... Please help the person not tech savy!

  I have 2 computers... one is a new laptop w / software advanced... the other is a hp tower that works under xp.  I searched for a trail version or a download of windows 7 or 8 if possible, but downloads only I've found require you to burn the files to a disk that I don't have the possibility to do so.  A 60 day trial version will do, but I can't locate a!  The Tower system is my husband, and he is absent until mid-May.  I need to make it until then... any advice/suggestions?  I would feel much safer if I need xp at least until mid-May.  I'm all thumbs when it comes to nothing technical.  Please, keep this in mind w / your answers!

  Unfortunately there is no trial version. If you want Windows 7 or 8, I'm afraid, you have to buy the operating system with a key Code. We can guide you in building a USB bootable for installing, but it is actually more difficult to burn a DVD to an .iso. I would also be sure that the material will actually in charge of Windows 7. Mania it on the end of XP support, it's just that... oversold. It is not something to be ignored, but if keep you a good antivirus, you should be OK for awhile (like 6 months to a year). XP actually has been precarious for some time now even with updates if you are at no more risk that you've visited for the last year or two and nothing terrible has happened, right?

• After that the computer is idle for a few minutes, you receive an error message. "Vtdispl display driver does not work properly, please restart the computer to solve the problem."

  I rebooted and turned power off the computer several times and always get the same message. The size of the text on the screen and the icons are larger than the way in which they should appear. How can I solve this problem?

  Consult the manufacturer of your so great PC OEM, for example Dell / HP or laptop and install the latest drivers.
  If a visit generic PC your graphics card maker or manufacturer of the motherboard and install drivers lates
  Do NOT get the drivers of MSUpdate

• Please help: the virtual disk parent has changed...

  After a few days of research about this error, I decided that I had to ask for some evidence of your experts to help me recover from this error.

  Thank you!

  It is a small desktop application:

  -Dell T410 esxi Server 5

  -a virtual machine, Windows Server 2003 with 2 discs, no fixed size

  I was help this office by managing services and updates on this Server 2003.  I ran updates on Friday and restarted.  When he came I open vSphere and found the virtual machine does not.  I tried to start it and got the error.  So, it seems I may have the CID issue that needs to be corrected.

  I don't have a direct access to this server so I'm remoting with RDS on 2003 VM server and vSphere on the esxi.  Did I make the right diagnosis and is it possible for me to make the necessary corrections to distance or I need direct access to the server?  Everything I've read has files of people editing CID numbers and it seems that they directly access the esxi server.

  Shows the data store:

  hard 'server '.

  hard 'server_1.

  'server' - 000001.vmdk

  "server_1" - 000001.vmdk

  'server' - snapshot1.vmsn

  I stuck a few newspapers below...

  DISC: Scsi0:0 [OPEN ' / vmfs/volumes/4f4781a4-15d3bbb8-2681-782bcb6a6964/server/server-000001.vmdk' persistent R]
  2012-08 - 05T 20: 00:06.022Z | VMX | DISKLIB-VMFS: ' / vmfs/volumes/4f4781a4-15d3bbb8-2681-782bcb6a6964/server/server-000001-delta.vmdk ': open with success (10) size = 5620404224, hd = 213826. Type 8
  2012-08 - 05T 20: 00:06.022Z | VMX | DISKLIB-DSCPTR: open [0]: "Server-000001 - delta.vmdk ' (0xa)
  2012-08 - 05T 20: 00:06.022Z | VMX | DISKLIB-LINK: open ' / vmfs/volumes/4f4781a4-15d3bbb8-2681-782bcb6a6964/server/server-000001.vmdk' (0xa): vmfsSparse, 35526656 sectors / 16.9 GB.
  2012-08 - 05T 20: 00:06.035Z | VMX | DISKLIB-VMFS: ' / vmfs/volumes/4f4781a4-15d3bbb8-2681-782bcb6a6964/server/server-flat.vmdk ': open with success (14) size = 18189647872, hd = 181059. Type 3
  2012-08 - 05T 20: 00:06.035Z | VMX | DISKLIB-DSCPTR: open [0]: 'server - flat hard' (0xe)
  2012-08 - 05T 20: 00:06.035Z | VMX | DISKLIB-LINK: open ' / vmfs/volumes/4f4781a4-15d3bbb8-2681-782bcb6a6964/server/server.vmdk' (0xe): vmfs, 35526656 sectors / 16.9 GB.
  2012-08 - 05T 20: 00:06.035Z | VMX | DISKLIB LINK: DiskLinkIsAttachPossible: incompatibility of the content ID (parentCID f72e60c7! = f05537b3) /vmfs/volumes/4f4781a4-15d3bbb8-2681-782bcb6a6964/server/server-000001.vmdk vmfs/volumes/4f4781a4-15d3bbb8-2681-782bcb6a6964/server/server.vmdk.
  2012-08 - 05T 20: 00:06.035Z | VMX | DISKLIB-STRING: ' / vmfs/volumes/4f4781a4-15d3bbb8-2681-782bcb6a6964/server/server.vmdk ': cannot open (the virtual disk parent has changed since the child was created.) The content of the virtual disk ID parent does not match the ID of parent for children's content).
  2012-08 - 05T 20: 00:06.035Z | VMX | DISKLIB-VMFS: ' / vmfs/volumes/4f4781a4-15d3bbb8-2681-782bcb6a6964/server/server-000001-delta.vmdk ': closed.
  2012-08 - 05T 20: 00:06.035Z | VMX | DISKLIB-VMFS: ' / vmfs/volumes/4f4781a4-15d3bbb8-2681-782bcb6a6964/server/server-flat.vmdk ': closed.
  2012-08 - 05T 20: 00:06.035Z | VMX | DISKLIB-LIB: can't open ' / vmfs/volumes/4f4781a4-15d3bbb8-2681-782bcb6a6964/server/server-000001.vmdk' with the virtual disk 0xa flags parent has changed since the child was created. The content of the virtual disk ID parent does not match the ID of parent for children (18) content.
  2012-08 - 05T 20: 00:06.035Z | VMX | DRIVE: Cannot open disk ' / vmfs/volumes/4f4781a4-15d3bbb8-2681-782bcb6a6964/server/server-000001.vmdk ': the virtual disk parent has changed since the child was created. The content of the virtual disk ID parent does not match the ID of parent for children (18) content.
  2012-08 - 05T 20: 00:06.035Z | VMX | Msg_Post: error
  2012-08 - 05T 20: 00:06.035Z | VMX | [msg.disk.noBackEnd] unable to open drive ' / vmfs/volumes/4f4781a4-15d3bbb8-2681-782bcb6a6964/server/server-000001.vmdk' or one of the snapshot disks it depends on.
  2012-08 - 05T 20: 00:06.035Z | VMX | [msg.disk.configureDiskError] reason: the virtual disk parent has changed since the child was created. The content of the virtual disk ID parent does not match the ID of parent matching the child content.
  2012-08 - 05T 20: 00:06.035Z | VMX |

  Thanks again for any direction you can provide!

  / r

  John

  The parentCID of the snapshot must match the CID from its parent, as shown in the log file

  "... The content ID mismatch (parentCID f72e60c7! = f05537b3)... »

  Server.VMDK

  CID = f05537b3
  parentCID = ffffffff

  Server - 000001.vmdk

  CID = a2b9ba8b
  parentCID = f72e60c7---> f05537b3

  Make sure you change the file on the host using the vi editor or - if you want to change the file in Windows - use an editor who is aware of the line breaks Unix (do not use Notepad!)

  Once this is done, I highly recommend that you take another cliché before you on the virtual computer. This prevents existing virtual disk files to be modified, so that you can return to this State where you need. After that everything works as expected, consider deleting all snapshots.

  André

• Design pen tool does not, please help the newbies!

  Hello

  I am very new in design, I'm working the pen tool, which has worked before when I was playing around with it on an earlier design, but I just downloaded the creative suite and when I use this design if I'm drawing a shape it creates black spots which first of all make it difficult to move to the next point Since it covers the image and then when I cut out the picture and paste in his party.

  You have a fill selected as a default, so when you create a form that's being filled with color. Before, you start to draw, the value none Fill and stroke a value as 1 point.

• Please help, unidentified network, Internet access without problem...

  Hello world...

  I have a Toshiba Satellite C850 performer windows 8 64-bit, and it was working fine, suddenly the wifi doesn't connect now and said internet access, when I press on troubleshoot it says "wifi is not a valid IP configuration", and also tried to connect through a LAN cable, it does not either, but other laptops and mobile phones perfectly connects to the network It happened after I installed Skype. !!! I know it's a coincidence, but thought I should say...

  I tried to disable the two network adapters, forget network then connection, tried to remove the 'Hello' in the firewall, but I was not even have Hello... I'm going crazy with her...

  I tried to disable the firewall, anti-virus uninstall, I got avast, I tried to disable IPv6.

  tried these commands cmd

  netsh winsock reset catalog

  netsh int ip reset reset.log hit

  ipconfig/flushdns

  He said

  «"«reset the interface...»»» Ok!
  "something that I don't remember now" reset OK!
  reset failed
  Access is denied

  «' There is no user specified parameters to be re-armed»»»

  Although I chose command prompt (admin)...

  also tried

  ipconfig/release

  ipconfig/renew

  It was the result

  

  Although I was connected at this time...

  Tried another router wifi at home with my brother, with no other connected devices but this win8 one, didn't work either...

  Tried to boot into "Safe Mode with network" no longer works...

  I tried to uninstall the driver and install the last, also did not work,

  I also disabled the (avast NDSI firewall driver) and the (avast firewall driver), didn't work...

  This is the screenshot of the ipconfig/all command

  

  I tried to take the IP address and the subnet mask and default gateway and DNS servers, since a working laptop and enter manually on this laptop from win8 but did not work, but now there is no 'limited access and no yellow triangle', but still no internet connectivity...

  Here are a few screenshots:

  

  

  My network is the first...

  

  and ALL this applies for WiFi AND cable LAN, and also I tried to connect my Samsung galaxy phone and tried 3 G connect via it's also did not work, but it used to work before the problem 

  HEEEEEEEELP PLEEEEEEEEAAAAAAAAAASE...

  Hello

  Please contact Microsoft Community.

  We appreciate your efforts and the provision of information in detail about the issue. As you have already tried some troubleshooting and your computer still does not connect to the internet. I suggest you to consult the article below and check if it helps.

  How to refresh, reset or restore your PC;

  Warning: When you use system restore to restore the computer to a previous state, the programs and updates that you have installed are removed.

  http://Windows.Microsoft.com/en-us/Windows-8/restore-refresh-reset-PC

  Important: refer to the section "restore your PC to an earlier point in time."

  Note: Try to restore your system to an earlier date when everything worked correctly.

  Meet us, then we can help you further.

• Can you please help with my installation of Flash problems?

  My Adobe Flash Player (AFP) has disappeared and I can't reinstall it.  I run Win 7 and IE10.  I was fine until 3 days ago.  Support AFP page tells me I do not have the AFP, but it's on my list "uninstall programs".  I have uninstall AFP, reboot, install AFP (using save-run with no error message), restart and check the AFP support page to be told that I don't have to AFP.  I repeated this process several times without success.  I notice that Adobe Reader 11 and my Adobe Elements are located in C:\Program Files (x 86) \Adobe\ but AFP isn't here.  Help, please!  Thank you.  (PS: Shockwave Flash Object is enabled for both 32-bit and 64-bit.)

  Flash Player is a browser plugin, not an executable program and therefore is not installed under Program Files.

  If you have Shockwave Flash enabled, it means that it is installed.  Maybe you have ActiveX filtering on?  See http://forums.adobe.com/thread/867968

• Please help with XP Pro SP2 download problem!

  I just had to re - install Windows XP Professional w / SP1a. I can't manually find SP2 to Windows Update for XP is not up-to-date. The only version I find is for professionals and Windows Update tells me to check the link for one version service pack. However, I searched for hours and cannot find one. Is anyone know where download of Microsoft for SP2 are so I can move me to SP3 or can someone tell me how to force automatic updates to update manually?

  The version for the pros can be used on single computers as well.

  Download it and save it in case you need more: http://www.microsoft.com/download/en/details.aspx?id=28

  For SP3: http://www.microsoft.com/download/en/details.aspx?id=24

  Operating systems supported: Windows XP Home Edition, Windows XP Professional edition, Windows XP Service Pack 1, Windows XP Service Pack

  If you already upgraded to SP1, you can jump directly to SP3.

  Steps to take before you install Windows XP Service Pack 3
  http://support.Microsoft.com/kb/950717

• "This is an instance of ACE virtual machine. Please open it in VMware Player. ' Problem [solved]

  My previous PC broke down with isk hard issues now, I have a bright and successful new to transfer the files.

  But it won't work. The error I get reads as follows: "this is an instance of ACE virtual machine. Please open it in VMware Player. »

  Folder of you for the virtual machine contains a subfolder of ACE resources, an ace.dat and an aceMaster.dat file.

  I think that I previously used VMware Workstation 6.0 and found that the first. I've ugraded to 6.5 hoping that would do the trick. Unfortunately, I still get the same old message.

  Any help would be really appreciated.

  This is what my VMX file looks like:

  . Encoding = "windows-1252".

  config.version = '8 '.

  virtualHW.version = "7".

  scsi0. Present = 'TRUE '.

  scsi0.virtualDev = "free".

  memsize = "1024".

  scsi0:0. Present = 'TRUE '.

  scsi0:0. FileName = "Test.vmdk".

  IDE1:0. Present = 'TRUE '.

  IDE1:0. AutoDetect = "FALSE".

  IDE1:0. DeviceType = "cdrom-raw"

  floppy0.startConnected = "FALSE".

  floppy0. AutoDetect = 'TRUE '.

  ethernet0. Present = 'TRUE '.

  ethernet0. ConnectionType = "nat".

  ethernet0.virtualDev = "e1000".

  ethernet0.wakeOnPcktRcv = "FALSE".

  USB. Present = 'TRUE '.

  EHCI. Present = 'TRUE '.

  Sound.Present = 'TRUE '.

  sound.fileName = "-1".

  Sound.AutoDetect = "TRUE".

  MKS. Enable3D = 'TRUE '.

  pciBridge0.present = 'TRUE '.

  pciBridge4.present = 'TRUE '.

  pciBridge4.virtualDev = "pcieRootPort"

  pciBridge4.functions = '8 '.

  pciBridge5.present = 'TRUE '.

  pciBridge5.virtualDev = "pcieRootPort"

  pciBridge5.functions = '8 '.

  pciBridge6.present = 'TRUE '.

  pciBridge6.virtualDev = "pcieRootPort"

  pciBridge6.functions = '8 '.

  pciBridge7.present = 'TRUE '.

  pciBridge7.virtualDev = "pcieRootPort"

  pciBridge7.functions = '8 '.

  vmci0. Present = 'TRUE '.

  roamingVM.exitBehavior = 'go '.

  displayName = "Test".

  guestOS = "winvista".

  NVRAM = "Test.nvram."

  virtualHW.productCompatibility = "hosted".

  FT.secondary0.enabled = 'TRUE '.

  Tools.Upgrade.Policy = "useGlobal".

  extendedConfigFile = "Test.vmxf".

  floppy0. FileName = "a":

  ethernet0. AddressType = 'generated '.

  UUID. Location = "56 4 d 6 b 01 28 34 of 0f - b5 97 e2 6f 3 a 08 a3 c8"

  UUID. BIOS = "56 4 d 6 b 01 28 34 of 0f - b5 97 e2 6f 3 a 08 a3 c8"

  scsi0:0. Redo = «»

  vmotion.checkpointFBSize = "134217728.

  pciBridge0.pciSlotNumber = "17".

  pciBridge4.pciSlotNumber = "21".

  pciBridge5.pciSlotNumber = "22".

  pciBridge6.pciSlotNumber = "23".

  pciBridge7.pciSlotNumber = "24".

  scsi0.pciSlotNumber = "16".

  usb.pciSlotNumber = "32".

  ethernet0.pciSlotNumber = "33".

  sound.pciSlotNumber = "34".

  ehci.pciSlotNumber = "35".

  vmci0.pciSlotNumber = '36 '.

  USB:0. Present = 'TRUE '.

  USB:1.present = 'TRUE '.

  ethernet0.generatedAddress = "00: 0C: 29:3's: a3:c8.

  ethernet0.generatedAddressOffset = '0 '.

  vmci0.ID = "138060744".

  tools.remindInstall = "FALSE".

  USB:1.DeviceType = "hub".

  USB:0. DeviceType = "mouse".

  IDE1:0.startConnected = 'TRUE '.

  tools.syncTime = "FALSE".

  IDE1:0. FileName = 'E: '.

  bios.forceSetupOnce = "FALSE".

  usb.autoConnect.device0 = ' path: autoclean 1/7/1:1 ".

  ethernet0.linkStatePropagation.enable = "FALSE".

  usb.autoConnect.device1 = «»

  usb.autoConnect.device2 = «»

  checkpoint.vmState = «»

  debugStub.winOffsets.version = '1 '.

  debugStub.winOffsets.value = '0xa0, 0x9c, 0 x 18, x 0 168, 0x14c, 16, 0 x 0, 248 x 210, 0x1f8, 0 x 84, 0 x 28, 0x18, 0x20, 0 x 24, 1'

  ethernet0.VNET = "VMnet8.

  Policy.VM.mvmtid = ' 52 bd 5 b bb 4 10 d 0 c 0d - 98 f8 aa 4F a5 66 45 fd.

  policy.vm.managedVMTemplate = "FALSE".

  policy.vm.managedVM = "FALSE".

  Hello

  Remove your vmx file lines "policy.vm.mvmtid" and "policy.vm.managedvm".

  Delete the following files:

  (1) ace.dat

  (2) aceMaster.dat

  (3) host.vmpl

  (4) iDLE-jAM | SC 2, SC 3 & VCP 4

  If you have found this device or any other answer useful please consider useful or correct buttons using attribute points