Podcast Connect Error: Read timed out

Similar Questions

• Get VPN client to connect, but request timed out when ping

  Hi, I use the router Cisco 837 as my VPN server. I am connected using Cisco VPN Client Version 5. But when I ping the ip of the router, I have request timed out. Here is my configuration:

  Building configuration... Current configuration : 3704 bytes ! version 12.4 no service pad service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname michael ! boot-start-marker boot-end-marker ! memory-size iomem 5 no logging console enable secret 5 $1$pZLW$9RZ8afI8QdGRq0ssaEJVu0 ! aaa new-model ! ! aaa authentication login default local aaa authentication login sdm_vpn_xauth_ml_1 local aaa authorization exec default local aaa authorization network sdm_vpn_group_ml_1 local ! aaa session-id common ! resource policy ! ip subnet-zero no ip dhcp use vrf connected ip dhcp excluded-address 192.168.1.1 ! ip dhcp pool michael    network 192.168.1.0 255.255.255.0    default-router 192.168.1.1    dns-server 202.134.0.155 ! ip dhcp pool excluded-address    host 192.168.1.4 255.255.255.0    hardware-address 01c8.d719.957a.b9 ! ! ip cef ip name-server 202.134.0.155 ip name-server 203.130.193.74 vpdn enable ! ! ! ! username michael privilege 15 secret 5 $1$ZJQu$KDigCvYWKkzuzdYHBEY7f. username danny privilege 10 secret 5 $1$BDs.$Ez0u9wY7ywiBzVd1ECX0N/ ! ! ! crypto isakmp policy 1 encr 3des authentication pre-share group 2 crypto isakmp xauth timeout 15 ! crypto isakmp client configuration group michaelvpn key vpnpassword pool SDM_POOL_1 acl 199 netmask 255.255.255.0 ! ! crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac ! crypto dynamic-map SDM_DYNMAP_1 1 set transform-set ESP-3DES-SHA ! ! crypto map SDM_CMAP_1 client authentication list sdm_vpn_xauth_ml_1 crypto map SDM_CMAP_1 isakmp authorization list sdm_vpn_group_ml_1 crypto map SDM_CMAP_1 client configuration address respond crypto map SDM_CMAP_1 65535 ipsec-isakmp dynamic SDM_DYNMAP_1 ! ! ! interface Ethernet0 description $FW_INSIDE$ ip address 192.168.1.1 255.255.255.0 ip nat inside ip virtual-reassembly ip tcp adjust-mss 1452 hold-queue 100 out ! interface Ethernet2 no ip address shutdown hold-queue 100 out ! interface ATM0 no ip address no atm ilmi-keepalive dsl operating-mode auto pvc 0/35   pppoe-client dial-pool-number 1 ! ! interface FastEthernet1 duplex auto speed auto ! interface FastEthernet2 duplex auto speed auto ! interface FastEthernet3 duplex auto speed auto ! interface FastEthernet4 duplex auto speed auto ! interface Virtual-PPP1 no ip address ! interface Dialer1 description $FW_OUTSIDE$ mtu 1492 ip address negotiated ip nat outside ip virtual-reassembly encapsulation ppp dialer pool 1 ppp chap hostname ispusername ppp chap password 0 isppassword ppp pap sent-username ispusername password 0 isppassword crypto map SDM_CMAP_1 ! ip local pool SDM_POOL_1 192.168.2.1 192.168.2.5 ip classless ip route 0.0.0.0 0.0.0.0 Dialer1 ip http server no ip http secure-server ! ip nat inside source static udp 192.168.1.0 1723 interface Dialer1 1723 ip nat inside source static tcp 192.168.1.4 21 interface Dialer1 21 ip nat inside source route-map SDM_RMAP_1 interface Dialer1 overload ! access-list 1 remark SDM_ACL Category=16 access-list 1 permit 192.0.0.0 0.255.255.255 access-list 102 remark SDM_ACL Category=2 access-list 102 deny   ip 192.168.1.0 0.0.0.255 192.168.2.0 0.0.0.255 access-list 102 permit ip 192.168.1.0 0.0.0.255 any access-list 199 permit ip 192.168.1.0 0.0.0.255 192.168.2.0 0.0.0.255 route-map SDM_RMAP_1 permit 1 match ip address 102 ! ! control-plane ! banner motd ^C Authorized Access Only UNAUTHORIZED ACCESS TO THIS DEVICE IS PROHIBITED You must have explicit permission to access this device. All activities performed on this device are logged. Any violations of access policy will result in disciplinary action. ^C ! line con 0 no modem enable line aux 0 line vty 0 4 ! scheduler max-task-time 5000 end
  
  Thank you, anny help will be appreciated.
  			 
  Hi Michael,
  I have been through the newspapers, they are not conclusive and only detrmine that Phase 1 is coming. However according to this error message % SYS-2-BADSHARE: Bad refcount in pak_enqueue, ptr = 81B50AD8, count = 0 we are hiiting a bug on ios. The id of the bug is CSCsl24693 and the solution is to switch to 12.4 (11) XJ.
  Can you re-execute him debugs and send me the detailed results.
  Kind regards
  Aman
  		   

• Series connection error (read & write)

  Hello everyone

  I would like to use rs232 to connect my GPS module, in fact I need to send the GPS configuration and receive data using the same port, so what I'm starting to do is to use the example for the labview (because I'm not so good at using labview) and the error message (in the attachment) I couldn't find a solution for this? Any body can help me please

  concerning

  Have you done a search for this error code? Simply install NI-VISA and the error will disappear.

• "Timed out, failed to connect to BrowserLab" error

  Hello

  I've seen some posts with this error but no real solution. I use the version of Dreamweaver CS6 5842 on Windows 7 x 64. I can connect to BrowserLab and URL of the sample preview very well.

  When I use the BrowserLab in DW Panel, however, and select Preview, my default browser (Chrome) launches, connects, and then I face the blank screen of default BrowserLab. Meanwhile, the group is sitting there saying «Launch BrowserLab»... "and seems to ignore that he threw it with success. The Panel in DW gives finally upward, showing the error "failed to connect to BrowserLab, Timed out," and a nasty red dot.

  I am in a large enterprise environment and cannot circumvent the authenticated proxy system - because of problems in the past with some software more alumni who is not proxy aware. Could be the cause of this error? All other programs (including Adobe Application Manager) that I use are able to request credentials and access the Internet successfully.

  Is that what I can do to use BrowserLab with Dreamweaver?
  

  Sorry to see Adobe give you the runaround "restart".

  I had exactly the same issue as yours, even if I was connected to the service. Then realized I was on windows, using Chrome which has its own shell separate from those installed in system flash.

  What worked for me was connecting BrowserCam via IE.

• GPS Timed Out error when querying location

  Hi all

  I worked with GPS and maps on BlackBerry OS 5.0 and it has been frustrating to say the least.  I have everything working, however I get an error 'GPS timed' out whenever I try to question my location.  I get this error on a real device, and not on the Simulator.  This happens for a MapField both the native BlackBerry map.

  Essentially, what I'm doing is looking for the current coordinates via GPS, translating these coordinates in an address through reverseGeocoding (a separate thread) and then using that zip code to find and locate a web service.  The web service to function properly, it is the GPS which is the problem.

  I'd appreciate it if someone could take a look at my code and see if something comes out.  Here's my LocationHandler (implementation of LocationListener):

  import javax.microedition.location.Criteria;
  import javax.microedition.location.Location;
  import javax.microedition.location.LocationException;
  import javax.microedition.location.LocationListener;
  import javax.microedition.location.LocationProvider;
  import javax.microedition.location.QualifiedCoordinates;
  import com.usps.mobile.blackberry.Constants;
  import com.usps.mobile.blackberry.Inform;
  import com.usps.mobile.blackberry.interfaces.ScreenLocation;
  
  public class LocationHandler extends Thread implements LocationListener {
      private ScreenLocation screen;
      private boolean periodicUpdates;
  
      public LocationHandler(ScreenLocation screen, boolean update) {
          this.screen = screen;
          this.periodicUpdates = update;
      }
  
      public void locationUpdated(LocationProvider provider, Location location) {
          QualifiedCoordinates qualifiedCoordinates = location
                  .getQualifiedCoordinates();
  
          int longitude = (int) (qualifiedCoordinates.getLongitude() * 1000000);
          int latitude = (int) (qualifiedCoordinates.getLatitude() * 1000000);
          new myReverseGeocode(longitude, latitude, screen);
      }
  
      public void providerStateChanged(LocationProvider provider, int newState) {
          // So far, nothing for this
      }
  
      /**
       * The thread
       */
      public void run() {
          Criteria criteria = new Criteria();
          criteria.setVerticalAccuracy(Constants.DEFAULT_VERTICAL_ACCURACY);
          criteria.setHorizontalAccuracy(Constants.DEFAULT_HORIZONTAL_ACCURACY);
          criteria.setCostAllowed(true);
          criteria
                  .setPreferredPowerConsumption(Constants.DEFAULT_GPS_POWER_CONSUMPTION);
  
          try {
              LocationProvider provider = LocationProvider.getInstance(criteria);
              Location location = provider.getLocation(-1);
  
              locationUpdated(provider, location);
              if (periodicUpdates) {
                  // Update every 1 minute
                  provider.setLocationListener(this, 60, -1, 10);
              }
          } catch (final LocationException e) {
  
              Inform.inform(e.getMessage());
  
              screen.setLocation(Constants.DEFAULT_LONGITUDE,
                      Constants.DEFAULT_LATITUDE);
          } catch (final InterruptedException e) {
  
              Inform.inform(e.getMessage());
  
              screen.setLocation(Constants.DEFAULT_LONGITUDE,
                      Constants.DEFAULT_LATITUDE);
          }
      }
  
  }
  

  Method setLocation in my main screen:

  public void setLocation(int longitude, int latitude, AddressInfo addrInfo) {
          synchronized (UiApplication.getEventLock()) {
              mapField.moveTo(latitude, longitude);
  
              mapField.setZoom(Math.max(mapField.getZoom() - 1, mapField
                      .getMinZoom()));
  
              doWebService(addrInfo.getField(AddressInfo.POSTAL_CODE));
          }
      }
  

  As I said, reverseGeocode() is on its own thread, and it's back a correct information.

  Thank you!

  On verizon.

  You will not be able to be assisted without access PDE.   The criteria that you have shown, is not mapped to stand alone.

  Autonomous may take some time to get and quite well must have a clear view of the sky for correct performance.

• vSphere high availability 'Élection' fails at 99% 'operation timed out' to 1 of the 2 hosts

  Hello

  We had a system with 1 host ESXi 5.1 with local disks.

  Now, we install redundancy by adding a 5.5 U2 ESXi host and a device of vCenter 5.5.

  After having installed and any addition to vcenter, we went the ESXi 5.1 to 5.5 U2 ESXi. The SAN works correctly (vMotion works on the own NETWORK card).

  Now, if I try to activate the high availability, both servers will install the HA Agent and start "Election".

  All the warehouses of data (4) on the SAN are chosen for the HA heartbeat, response of isolation is "keep it turned on" by default.

  A server will always be this process done, and the other will keep "elect" until it reaches 100% and errors on the operation "election timed out.

  I've seen this problem on both servers, so I think that the 'master' elected does not have the problem, only the "slave".

  I have checked these items and executed, but not worked:

  VMware KB: Reconfiguration HA (FDM) on a cluster fails with the error: operation timed out

  -The services were running

  VMware KB: Configuration HA in VMware vCenter Server 5.x does not work, error: Operation Timed out

  -All the MTU has been set at 1500

  VMware KB: VMware High Availability Configuration fails with the error: unable to complete the configuration of the ag of HA...

  -the default gateway is not the same on the two hosts, but I fixed that. There is no itinerary changes. HA the setting is "leave power." After correction and deactivation/reactivation HA, the problem is always the same.

  VMware KB: Check and reinstall the correct version of the VMware vCenter Server agents

  -J' ran "Reinstall ESX host management agents and HA on ESXi" agent of HA, and I checked that it was uninstalled and reinstalled during the reactivation of HA.

  CP /opt/vmware/uninstallers/VMware-fdm-uninstall.sh/tmp
  chmod + x /tmp/VMware-fdm-uninstall.sh
  /tmp/vmware-FDM-uninstall.sh

  I did this for two guests. This fix makes the problem of the election and I was still able to run a HA test successfully, but when after this test, I turned off the 2nd Server (in order to test the PA in the other direction), HA has no failover to 1 and everything remained low. After pressing 'reconfigure HA', the problem of the election appeared again on 1 hosts.

  Here are a few extractions of newspapers:

  -L' availability vSphere HA of that host State became election info 29/11/2014 22:03 192.27.224.138

  -vSphere HA agent is healthy info 29/11/2014 22:02:56 192.27.224.138

  -L' availability vSphere HA of that host State became Master info 29/11/2014 22:02:56 192.27.224.138

  -L' availability vSphere HA of that host State became election info 29/11/2014 22:01:26 192.27.224.138

  -vSphere HA agent is healthy info 29/11/2014 22:01:22 192.27.224.138

  -L' availability vSphere HA of that host State became Master info 29/11/2014 22:01:22 192.27.224.138

  -L' availability vSphere HA of that host State became election info 29/11/2014 22:03:02 192.27.224.139

  -Message "host vSphere HA State" on 192.27.224.139 changes from green to red info 29/11/2014 22:02:58 192.27.224.139

  officer of HA - vSphere for this host has an error: vSphere HA agent may not be properly installed or configured WARNING 29/11/2014 22:02:58 192.27.224.139

  -L' availability vSphere HA of that host State became info error of initialization of 29/11/2014 22:02:58 192.27.224.139

  -L' availability vSphere HA of that host State became election info 29/11/2014 22:00:52 192.27.224.139

  -DSMD3400DG2VD2 data store is selected for the storage heartbeat controlled by the HA agent vSphere on this info host 29/11/2014 22:00:49 192.27.224.139

  -DSMD3400DG2VD1 data store is selected for the storage heartbeat controlled by the HA agent vSphere on this info host 29/11/2014 22:00:49 192.27.224.139

  -Firewall configuration has changed. 'Enable' to rule the fdm value successful.  29/11/2014 info 22:00:45 192.27.224.139

  -L' availability vSphere HA of that host State became not initialized info 29/11/2014 22:00:40 reconfigures vSphere HA 192.27.224.139 root host

  -vSphere HA agent on this host is disabled info 29/11/2014 22:00:40 reconfigures vSphere HA 192.27.224.139 root

  -Reconfigure HA vSphere host 192.27.224.139 operation has timed out.     root of HOSTSERVER01 29/11/2014 22:00:31 29/11/2014 22:00:31 29/11/2014 22:02:51

  -Configuration of vSphere HA 192.27.224.139 operation has timed out.     System HOSTSERVER01 29/11/2014 21:56:42 29/11/2014 21:56:42 29/11/2014 21:58:55

  Can someone give me please with help here?

  Or the extra things that I can check or provide?

  I'm currenty running options.

  Best regards

  Joris

  P.S. I had problems with cold Migration during the implementation of the SAN. After setting up all (vMotion, ESX upgrade), these problems have disappeared.

  When you search for this error, I came to this article: KB VMware: VMware vCenter Server displays the error message: unable to connect to the host

  And this cause could make sense, since the server vCenter changed and IP addressing has been changed during the implementation.

  However, in the file vpxa.cfg, the < hostip > and < serverip > is correct (verified by using https://< hostip > / home).

  Tried this again today, no problem at all.
  

  P.P.S. I have set up several of these systems from scratch in the past without problem (if it is an 'upgrade').

  OK, so the problem is solved.

  I contacted Dell Pro Support (OEM offering the license) and they checked the logs (fdm.log) and found that the default IP gateway could not be reached.

  The default gateway is the ip address by default host isolation, used by HA.

  Because it is an isolated production system, the front door provided proved only for future purposes.

  Now, I've changed the default gateway address of management on the switch plugged into both hosts, namely the ping requests.

  This solved any problem.

• 'Operation timed out', while protecting a virtual machine

  When you try to configure protection on a virtual machine in 4.1 SRM and every time I do it fails with the error 'Operation timed out' and I see the following error message in the log of Site Recovery Manager:

  2010-09-21 14:07:29.502 04584 verbose "PropertyProvider" ASSIGN RecordOp: info.error, com.vmware.vcDr.ReplicationGroup.AddVmTask - 153

  2010-09-21 14:07:29.502 04584 'com.vmware.vcDr.ReplicationGroup.AddVmTask - Task' verbose Error value {(vim.fault.Timedout)

  dynamicType = & lt; unset & gt;

  faultCause = (vmodl. NULL in MethodFault),

  MSG = ""

  }

  2010-09-21 14:07:29.502 04584 verbose "PropertyProvider" ASSIGN RecordOp: info.completeTime, com.vmware.vcDr.ReplicationGroup.AddVmTask - 153

  2010-09-21 14:07:29.502 04584 info 'com.vmware.vcDr.ReplicationGroup.AddVmTask - Task' State of the error value

  2010-09-21 14:07:29.502 04584 verbose "PropertyProvider" ASSIGN RecordOp: info.state, com.vmware.vcDr.ReplicationGroup.AddVmTask - 153

  2010-09-21 14:07:29.502 04584 verbose "PropertyProvider" RecordOp REMOVE: addVmsTaskList, group-4425'

  Someone at - it no indication on what this alarm tells me and how to fix?

  Thank you.

  V.

  I saw this problem after repairing the installation of SRM. Restart both servers SRM has solved the problem.

  In your case, this is the new installation or did you 'fix' recently?

• Local Connection Timed out after error ~ 12000sec

  Hello

  I send a soap request to a service wcf web.

  I am able to get the required xml response when I open in the Internet Explorer browser but when I open it in the simulator it says Local connection timed out after ~ 12000sec and also when I deploy it to the device, it gives the answer as [object.document]. Please let me know if I'm missing something. Is the code used to call the Web service

  function {} Getresults()

  var XMLHTTP;

  If (! xmlhttp & typeof XMLHttpRequest! = 'undefined') {}

  try {xmlhttp = new XMLHttpRequest();                }

  catch (e) {xmlhttp = false;}                }           }

  return xmlhttp;       }

  var xmlHttp = new Getresults();

  var xmlHttp = new ActiveXObject ("Microsoft.XMLHTTP");

  function getDynamicData() {}

  var url = "http://serverip/Service.Wcf/Service.svc";

  XMLHTTP.open("get",URL,true) ("GET", url, true);

  xmlHttp.onreadystatechange = callbackFunction;

  xmlHttp.setRequestHeader ("SOAPAction ','http://tempuri.org/IService/GetVolume_PerYear'");            xmlHttp.setRequestHeader ("Content-Type', ' text/xml; charset = utf - 8');

  var soapRequest = '' +

  http://www.w3.org/2001/XMLSchema-instance' ' + ' container ="http://www.w3.org/2001/XMLSchema" "' + ' xmlns:soap = 'http://schemas.xmlsoap.org/soap/envelope/' > ' + '"

  ' ' +

  "'http://tempuri.org/ ' > ' +.

  '' +

  '' +

  '';

  xmlHttp.send (soapRequest);       }

  function callbackFunction() {}

  Alert (XMLHTTP. ReadyState);

  If (xmlHttp.readyState! = 4)

  return;

  Alert (XMLHTTP.responseXML);  }

  everything looks very well, try changing this XMLHTTP.open("get",URL,true) ('GET', url, true);   by XMLHTTP.open("get",URL,true) ('POST', url, true);

  subdomains also try to change this access urihttp://serverip/Service.Wcf"="true"> by

• "We could not complete your iTunes Store request. The network connection timed out. »

  Every hour or two iTunes for Mac displays a modal dialog box with the error 'we could not complete your iTunes Store request. The network connection timed out. "This interrupts any activity like playing airplay or order with the Remote App on iOS.

  I can identify no problems of networks. If I go to the iTunes Store deliberately I have no problem. I have no download waiting on the iTunes store. I try not to buy anything from the iTunes Store. I have no reason to connect to the iTunes Store.

  There is no update unapplied for iTunes. There is no update unapplied for Mac OS X. There is no update unapplied for my router. There is no network connection problem to any site I found.

  I can't find all the messages that allow me to debug this problem. The support page to If you can not connect to the iTunes Store - Apple supported provides no useful information.

  What this error message should tell me? What problem I actually feel?

  I noticed that sometimes.  I just quit iTunes and restart.  The problem reoccur not (until it is once again).  But for me, it's months between occurrences.

• When using windows scan & fax tool I get: _ 'network processing timed out. Check the scanner settings & network"error

  I am running Vista ultimate on 64-bit computer with a Linksys WRT310n router in LAN mode. I also have a Canon MF4370dn printer that prints screen & documents ok. I can see the printer on the network.

  I'm mainly interested in the function of scan here.
  With the mf scanner set to scan mode of network (according to Canon), I opened the Windows scan & fax tool, I select the WIA Canon scangear printer/scanner/fax to network & I get a panel where you select dpi/jpeg/bmp etc. When I select the function preview or scan I get an error message that says "network timed out treatment. Check the settings of the scanner & network.

  I read a lot of sour comments on the analysis of the network of this machine. It's a shame, because it is a machine of great, fast & compact mono laser. I have disabled the firewall of the router, still no go. I also tried the rout USB with software to reinstall with network for others, printing & for my machine but italways deferred to the network on mine with the same error message.

  I also read where it analyzes only at 300 dpi... so with all these pros & cons I decided to get a good, dedicated, scan that will probably better results of the scanner anyway.

  Thank you for all the good sites & info you have provided.

  Newbie.

• Game get unresponsive, a communication error has occurred: Operation Timed out

  A communication error has occurred: "Operation timed out".

  The Web server may be down, too busy or other problems preventing him from answering. You can try again at a later date.

  For assistance, contact your network support team. That's what I get when I try to access a game I play. Worked fine when I stopped last night, but all day was like that, everything is fine.

  Hello

  ·          Game in which you try to read?

  ·          You play this game online?

  I would say also, please contact game support to check their end technical issues.

• "Connection timed out" blackBerry smartphones at the opening of MSN

  As the name of the topic, says when I try to open my Windows Live Messenger on the Curve 8900, the white screen with the blue Blackberry logo appears and the charge takes 2 minutes or more. At the end of the load, an error message comes up saying that 'connection timed out '.

  I live in Vancouver and I am with Rogers, I use the $25 unlimited email/IM, text plan. Is this something with the settings on my phone or something with my ISP? Anyone who has a solution?

  Thank you!

  Hi I found what was wrong. I called Rogers and was told that the Windows Live Messenger icon preloaded in the phone is just a shortcut and the program is not already installed. Which means that I have to download the actual program. But since I do not have a web navigation plan (only for e-mail and instant messaging, and text), I couldn't connect to the internet to download the Messenger. I have finished downloading on a WiFi network, now it works fine.

• Save not finished. message is 'Timed Out' error 0 x 81000101

  Upward does not end on the external drive. Received message is 'Back Up Timed Out'. What this means and how do I enable backup complete a copy of the C drive information in its entirety. Error message is 0 x 81000101

  Hello

  Thanks for posting in the Forum the Microsoft community.

  According to your description, I understand that you are unable to perform a backup, and you receive error message like 0 x 81000101.

  To better understand the question, please answer the following questions:

  1 are you connected to a domain network?

  2. do you use the Windows backup feature to backup?

  3. What is the size of the data you are trying to add or backup?

  4. have you made changes on the computer before this problem?

  5. have you installed third-party backup utility?

  6. what kind of backup do you run?

  Come back with more information to help you better.

  Follow the mentioned methods:

  Method 1: Check if these two services are running:

  A. Volume Shadow Copy service

  B. backup Windows

  Also to ensure that their dependency services are running. You can check this information from services.msc. Follow the steps below to check the services.

  (a) go to start and type services.msc in the search box.

  (b) search for both services.

  (c) make a right click on the service, one at a time.

  (d) select Properties.

  (e) go to start type.

  (f) select Auto

   

  Method 2:

   

  Run the disk check to find and fix errors on the disc.

  (a) click Start, type cmd, right-click cmd, and then click Run as administrator.

  (b) at the prompt, type chkdsk /f /r and press to enter.

  (c) try to save and check the result.

  For more information on 'Check a drive for errors' please visit this link:

  http://Windows.Microsoft.com/en-us/Windows7/check-a-drive-for-errors

  Note: For security, try to manually back up data before a disk check. Running chkdsk on the drive if bad sectors are found on the disk hard when chkdsk attempts to repair this area if all available on which data may be lost

  Method 3:

   

  Step 1:

   

  You can also temporarily disable the security software and check if the problem persists. Be sure to enable this security software on the computer after checking.

  http://Windows.Microsoft.com/en-us/Windows7/turn-Windows-Firewall-on-or-off

  http://Windows.Microsoft.com/en-us/Windows7/disable-antivirus-software

  If disabling the security software solves the problem, then contact the manufacturer of the specific security software to fix the problem.

  Important note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks.

   

   

  Step 2:

   

  Also try to set up your computer in a clean boot state, and check to see if the same problem happens.

  By setting your boot system minimum state helps determine if third-party applications or startup items are causing the problem.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or Windows 7:
  http://support.Microsoft.com/kb/929135

  Note: After the boot minimum troubleshooting step, followstep 7 in the link provided to return the computer to a Normal startup mode.

  For more information on the "backup of your files' visit this link:

  http://Windows.Microsoft.com/en-us/Windows7/back-up-your-files

  Hope the above information is helpful. If you have any question back to us, we are happy to help you.

  Thank you.

• I get Connection Timed Out

  Recently, I've been doing the Connection Timed Out on some sites. I have cleared my cache and cookies, and it still happens. I tried in safe mode and it still happens. I don't know what else to do besides just uninstall and reinstall firefox, and I don't know if this will even help.

  Now, here's the real kicker. The warning is not always to her for the same sites, and sometimes almost randomly. For a long time that it didn't happen and now it seems to start up again.

  So I have really no idea what to do. Can someone help me please. Also, I'm a bit of a novice when it comes to the computer speak, so if you have a question that may be a bit overwhelming, could you dumb it down a little for me.

  To be honest, I think I understood the connection problem. However, the connection was reset problem seems to happen after I visit Deviantart. No other site does seem to cause the problem. Is that what I can do to avoid this problem, when I visit this site?

• Connection timed out on the Web site. Tried to delete the cache/cookies. No proxy. Internet Explorer. Unable to access. Help, please. Site Web works.

  I get Connection Timed Out on these Web sites: energy-medicine - software.com and energy - medicine.info. I tried to clear cookies and cache. I put no Proxy. I tried Internet Explorer and are still unable to access. I restarted my computer. I know that this site is active, because I contacted the webmaster and he says that it is active to an end. What else can I do to access this site? Thank you!

  Make a check of malware with several malware scanning of programs on the Windows computer.
  Please scan with all programs, because each program detects a different malicious program.
  All of these programs have free versions.

  Make sure that you update each program to get the latest version of their databases before scanning.

  • Malwarebytes' Anti-Malware:
    http://www.Malwarebytes.org/MBAM.php
  • AdwCleaner:
    http://www.bleepingcomputer.com/download/adwcleaner/
    http://www.Softpedia.com/get/antivirus/removal-tools/AdwCleaner.shtml
  • SuperAntispyware:
    http://www.SUPERAntiSpyware.com/
  • Microsoft security scanner:
    http://www.Microsoft.com/security/scanner/en-us/default.aspx
  • Windows Defender:
    http://Windows.Microsoft.com/en-us/Windows/using-Defender
  • Spybot Search & Destroy:
    http://www.safer-networking.org/en/index.html
  • Kasperky free Security Scan:
    http://www.Kaspersky.com/security-scan

  Alternatively, you can write a check for an infection rootkit TDSSKiller.

  • Utility anti-rootkit TDSSKiller:
    http://support.Kaspersky.com/5350?El=88446

  See also:

  • "Spyware on Windows": http://kb.mozillazine.org/Popups_not_blocked
  • https://support.Mozilla.org/KB/troubleshoot-Firefox-issues-caused-malware