Policy global config use IPS (ASA 5520)

Similar Questions

• Using Cisco Client to site VPN on a behind a NAT ASA 5520

  I apologize if this has been asked and we answered in the forums.  I looked, and while I found a large number of entries that were dancing all around this question, I never found nothing which addressed this specific issue.   We currently use an ASA 5520 as the head end of a relatively large customer to site IPSEC VPN (approximately 240 users, not consecutively).   This ASA is currently sitting behind a Checkpoint firewall with a real publicly addressable IP address on its public interface.  All of our customers use the legacy Cisco VPN (not the one anyconnect) client.  We plan to a few controllers F5 link set up between ISPS and firewalls.   For VPN connectivity F5 recommends that we NAT IP address (called a broad IP) to point back to a private IP address on the ASA and F5.  My question is, will this work?   I've always heard say that the head of line needed to have a public IP address on this subject because this is what will be placed in packages for the client to respond to.

  For further information, here's what we have now and what we are invited to attend.

  Current

  ISP - router - firewall-fire - ASA (public IP address as endpoint)

  Proposed

  ISP - router - F5 (public IP address as endpoint using a NAT to ASA) - Firewall - ASA (10.X.X.X as its external interface)

  Proposed alternative

  ISP - router - F5 (public IP address as endpoint using a NAT to ASA) - ASA (10.X.X.X as its external interface)

  All thoughts at this moment would be greatly appreciated.   Thank you!

  Hello

  If there is a static NAT one by one on F5 to the external interface of the ASA, then I don't think they would be any problems.
  Because when the client will attempt to connect to IKE to the translated public IP, F5 will redirect the request to ASA outside interface that is configured for the VPN.

  In addition, to ensure the udp500, 4500 and esp is allowed and then you should be good to go.

  HTH

  Concerning
  Mohit

• VPN site to Site with ASA 5520 * please help *.

  I am using two ASA 5520, and try to put up a site to site VPN.  This seems to be pretty simple, but I'm on my third day of train this is up and running. Both 5520's are running the latest 9.1 (5) IOS.

  Please note: I replaced it with [#1-WAN IP] and [#2-WAN IP] for WAN IP of the ASA addresses.

  Thanks in advance for any help you may have.

  -------------------------------------------------------------------------------------------------------------------------------------------------

  ASA 5520 # 1:

  Crypto ikev1 allow outside

  the local object of net network
  10.0.0.0 subnet 255.255.255.0

  net remote object network
  172.20.0.0 subnet 255.255.255.0

  outside_1_cryptomap list of allowed ip object local net net access / remote

  tunnel-group [IP #2-WAN] type ipsec-l2l

  IPSec-attributes tunnel-group [#2-WAN IP]
  pre-shared-key cisco123

  IKEv1 crypto policy 10
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 86400

  Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac

  card crypto oustide_map 1 match address outside_1_cryptomap
  card crypto oustide_map 1 set transform-set ESP-3DES-SHA ikev1
  card crypto outside_map 1 set pfs Group1
  map 1 set outside_map crypto peer [#2-WAN IP]
  outside_map interface card crypto outside

  NAT (inside, outside) 1 local static source net net-local destination static remote net net / remote

  -------------------------------------------------------------------------------------------------------------------------------------------------

  ASA 5520 #2:

  Crypto ikev1 allow outside

  the local object of net network
  172.20.0.0 subnet 255.255.255.0

  net remote object network
  10.0.0.0 subnet 255.255.255.0

  outside_1_cryptomap list of allowed ip object local net net access / remote

  tunnel-group [#1-WAN IP] type ipsec-l2l

  IPSec-attributes tunnel-group [#1-WAN IP]
  pre-shared-key cisco123

  IKEv1 crypto policy 10
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 86400

  Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac

  card crypto oustide_map 1 match address outside_1_cryptomap
  card crypto oustide_map 1 set transform-set ESP-3DES-SHA ikev1
  card crypto outside_map 1 set pfs Group1
  map 1 set outside_map crypto peer [#1-WAN IP]
  outside_map interface card crypto outside

  NAT (inside, outside) 1 local static source net net-local destination static remote net net / remote

  Try to correct the mistakes in the two configs.

  In some places, you have 'oustide_map' where you need "outside_map".

• ASA 5520 IPSec NAT question

  I like more than 150 of VPN on my ASA 5520.  A specific customer, with that I'll put up a VPN has an overlap of two of the intellectual property, it must reach from its internal network.  It is NATing 10.251.11.177 internal network traffic to my ASA presents itself as 10.251.11.177 of the 10.251.11.176/29 network.  Now the two IP of its internal network, it must reach are 10.1.254.200 and 10.1.254.201.

  Thus, following the documentation on the site Web of Cisco I'm doing Policy Based Routing on the ASA 5520 (my thesis) so that its traffic will 1.1.1.1 and 1.1.1.2 instead of 10.1.254.200 and 10.1.254.201.  Once it reaches my ASA 5520 it gets back to these IP tranlated.

  I am using the following configuration, but when I try to add static entries, it won't let me add them.  I even tried "static 1.1.1.1 (exterior, Interior) POLICYNAT of the access list" with the ACL in reverse but no use.

  object-group, network VPN-map

  network-object host 1.1.1.1

  network-object host 1.1.1.2

  !

  POLICYNAT list extended access allowed host ip 10.1.254.200 10.251.11.176 255.255.255.248

  POLICYNAT list extended access allowed host ip 10.1.254.201 10.251.11.176 255.255.255.248

  !

  static (inside, outside) 1.1.1.1 access-list POLICYNAT

  public static (inside, outside) 1.1.1.2 - POLICYNAT access list

  Try breaking the IPs in two ACL

  POLICYNAT1 list extended access allowed host ip 10.1.254.200 10.251.11.176 255.255.255.248

  POLICYNAT2 list extended access allowed host ip 10.1.254.201 10.251.11.176 255.255.255.248

  !

  static (inside, outside) 1.1.1.1 access-list POLICYNAT1

  public static (inside, outside) 1.1.1.2 - POLICYNAT2 access list

  HTH

  GE

• ASA 5520 - VPN using LDAP access control

  I'm setting up an ASA 5520 for VPN access.  Authorization & authentication using an LDAP server.  I have successfully configured tunnel, and I can access internal resources.  What I want to do now is to limit access to a specific ad group membership.  In the absence of this belonging to a group, a user cannot access the VPN.

  My VPN client software testing is Cisco Systems VPN Client 5.0.05.0290 Version.  The Group authentication is configured in a connection entry that identifies the Group of Tunnel. I think I wrote that correctly.

  The Version of the software on the SAA is 8.3 (1).

  My current challenge is getting the VPN to stop letting each request for access through little matter belonging to a group.  I found the thread below to be significantly useful, but there is obviously something which is not entirely mesh with my situation.

  https://supportforums.Cisco.com/message/3232649#3232649

  Thanking all in advance for everything offered thoughts and advice.

  Configuration (AAA LDAP, group policy and group of tunnel) is below.

  AAA-Server LDAP protocol ldap
  AAA-Server LDAP (inside) host x.x.y.12
  Server-port 636
  LDAP-base-dn dc = domain, dc = com
  LDAP-scope subtree
  LDAP-naming-attribute sAMAccountName
  LDAP-login-password *.
  LDAP-connection-dn cn = svcacct, or = svcac, or = users, or = svcad, dc = domain, dc = com
  enable LDAP over ssl
  microsoft server type
  LDAP-attribute-map LDAP_MAP
  AAA-Server LDAP (inside) host x.x.y.10
  Server-port 636
  LDAP-base-dn dc = domain, dc = com
  LDAP-scope subtree
  LDAP-naming-attribute sAMAccountName
  LDAP-login-password *.
  LDAP-connection-dn cn = svcacct, or = svcac, or = users, or = svcad, dc = domain, dc = com
  enable LDAP over ssl
  LDAP-attribute-map LDAP_MAP
  AAA-Server LDAP (inside) host x.x.y.11
  Server-port 636
  LDAP-base-dn dc = domain, dc = com
  LDAP-scope subtree
  LDAP-naming-attribute sAMAccountName
  LDAP-login-password *.
  LDAP-connection-dn cn = svcacct, or = svcac, or = users, or = svcad, dc = domain, dc = com
  enable LDAP over ssl
  microsoft server type
  LDAP-attribute-map LDAP_MAP

  AAA-Server LDAP (inside) host x.x.y.10
  Server-port 636
  LDAP-base-dn dc = domain, dc = com
  LDAP-scope subtree
  LDAP-naming-attribute sAMAccountName
  LDAP-login-password *.
  LDAP-connection-dn cn = svcacct, or = svcac, or = users, or = svcad, dc = domain, dc = com
  enable LDAP over ssl
  LDAP-attribute-map LDAP_MAP
  AAA-Server LDAP (inside) host x.x.y.11
  Server-port 636
  LDAP-base-dn dc = domain, dc = com
  LDAP-scope subtree
  LDAP-naming-attribute sAMAccountName
  LDAP-login-password *.
  LDAP-connection-dn cn = svcacct, or = svcac, or = users, or = svcad, dc = domain, dc = com
  enable LDAP over ssl
  microsoft server type
  LDAP-attribute-map LDAP_MAP
  !
  internal group NOACCESS strategy
  NOACCESS group policy attributes
  VPN - concurrent connections 0
  Protocol-tunnel-VPN IPSec webvpn
  address pools no
  attributes of Group Policy DfltGrpPolicy
  VPN - 10 concurrent connections
  Protocol-tunnel-VPN IPSec webvpn
  enable IPSec-udp
  vpn group policy - pro internal
  vpn - pro group policy attributes
  value x.x.y.17 x.x.y.27 WINS server
  Server DNS value x.x.y.19 x.x.y.29
  VPN - 50 simultaneous connections
  Protocol-tunnel-VPN IPSec svc
  group-lock value vpn - pro
  field default value domain.com
  value of address ip-vpn-pro pools
  WebVPN
  client of dpd-interval SVC no
  dpd-interval SVC 1800 bridge
  !

  attributes global-tunnel-group DefaultRAGroup
  LDAP authentication group-server
  LDAP authorization-server-group
  Group Policy - by default-vpn-pro
  authorization required
  type group tunnel vpn - pro remote access
  attributes global-tunnel-group-vpn - pro
  LDAP authentication group-server
  Group-server-authentication (LDAP outside)
  LDAP authorization-server-group
  Group Policy - by default-vpn-pro
  band-Kingdom
  password-management
  band-band
  authorization required
  type tunnel-group NOACCESSGROUP remote access
  attributes global-tunnel-group NOACCESSGROUP
  LDAP authentication group-server
  NOACCESS by default-group-policy

  Hello

  The configuration of what you are looking for is a feature called DAP (Dynamic Access Policy)

  The following link will explain how to set up the same.

  http://www.ciscosystems.com/en/us/products/ps6120/products_white_paper09186a00809fcf38.shtml

  I hope this helps.

  Kind regards

  Anisha

  P.S.: Please mark this thread as answered if you feel that your query is resolved. Note the useful messages.

• Cisco ASA 5520, 8.02, 4GE SSM, IPS?

  I have an ASA 5520 with 4GE SSM module.

  The ASDM, I see IPS basic signatures... anyway to upgrade these signatures, add to, etc.?

  Not really, you must purchase the AIP - SSM module for this.

  Concerning

  Farrukh

• SSL VPN using ASA 5520 mode cluster - several problems

  I configured 2 ASA 5520 s in the load balancing cluster mode. I connect using anyconnect and I download the customer the first time and everything works well except outlook. I don't know why outlook does not work.

  The second problem is after the anyconnect client is installed on your machine, he remembers that ASA (say ASA2) he first connected and the GUI shows the address IP of ASA2 instead of the virtual IP address of the cluster. I want users always connect using the virtual IP address.

  The third problem I have is there is a default group of SSL VPN and I want all users to use this group. In the initial web page, there is a drop down menu which shows that this group, but I still want to disable this menu drop-down.

  Any suggestions?

  To disable the drop-down menu, you can turn it off with the command

  WebVPN

  no activation of tunnel-group-list

  This will take care of your last issue.

  ***************************

  You can create a profile of the Anyconnect client with the name of the server you want to connect with and that make the ASA that will solve your problem of virtual IP.

  **************************

  Regarding Outlook, do you use specific ports which allows inspection of the ASA. Take a look at the list of inspection on the SAA and perhaps try to disable inspection and see if it works.

  *****************************

• nat ASA 5520 problem

  Hi I have a Cisco Asa 5520 and I want to vpn site-to-site by using another interface with a carrier of lan to lan, the problem is when I try to pass traffic have the syslog error to follow:

  No translation not found for udp src lan2lan:10.5.50.63/44437 dst colo: biggiesmalls groups / 897
   
  LAN to LAN service interface is called: lan2lan
  one of the internal interfaces is called: colo
  
  I think that is problem with Nat on the SAA but I need help with this.
   
  Config:
   
  !
  interface GigabitEthernet0/0
  nameif outside
  security-level 0
  eve of fw - ext 255.255.255.0 address IP XXaaaNNaa
  OSPF cost 10
  OSPF network point-to-point non-broadcast
  !
  interface GigabitEthernet0/1
  No nameif
  no level of security
  no ip address
  !
  interface GigabitEthernet0/1.50
  VLAN 50
  nameif lb
  security-level 20
  IP 10.1.50.11 255.255.255.0
  OSPF cost 10
  !
  interface GigabitEthernet0/1,501
  VLAN 501
  nameif colo
  security-level 90
  eve of fw - int 255.255.255.0 172.16.2.253 IP address
  OSPF cost 10
  !
  !
  interface GigabitEthernet1/1
  Door-Lan2Lan description
  nameif lan2lan
  security-level 0
  IP 10.100.50.1 255.255.255.248
  !
  access extensive list ip 10.1.0.0 lan2lan_cryptomap_51 allow 255.255.0.0 object-group elo
  permit access list extended ip sfnet 255.255.255.0 lan2lan_cryptomap_51 object-group elo
  pager lines 24
  Enable logging
  host colo biggiesmalls record
  No message logging 313001
  External MTU 1500
  MTU 1500 lb
  MTU 1500 Colo
  lan2lan MTU 1500
  ICMP unreachable rate-limit 1 burst-size 1
  ARP timeout 14400
  NAT-control
  Global 1 interface (external)
  interface of global (lb) 1
  Global (colo) 1 interface
  NAT (lb) 1 10.1.50.0 255.255.255.0
  NAT (colo) - access list 0 colo_nat0_outbound
  NAT (colo) 1 10.1.13.0 255.255.255.0
  NAT (colo) 1 10.1.16.0 255.255.255.0
  NAT (colo) 1 0.0.0.0 0.0.0.0
  external_access_in access to the external interface group
  Access-group lb_access_in in lb interface
  Access-group colo_access_in in interface colo
  Access-group management_access_in in management of the interface
  Access-group interface lan2lan lan2lan
  !
  Service resetoutside
  card crypto match 51 lan2lan_map address lan2lan_cryptomap_51
  lan2lan_map 51 crypto map set peer 10.100.50.2
  card crypto lan2lan_map 51 game of transformation-ESP-3DES-SHA
  crypto lan2lan_map 51 set reverse-road map
  lan2lan_map interface lan2lan crypto card
  quit smoking
  ISAKMP crypto identity hostname
  ISAKMP crypto enable lan2lan
  crypto ISAKMP policy 10
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 86400
  Crypto isakmp nat-traversal 20
  enable client-implementation to date
  IPSec-attributes tunnel-group DefaultL2LGroup
  pre-shared-key xxXnnAA
  tunnel-group 10.100.50.2 type ipsec-l2l
  tunnel-group 10.100.50.2 General-attributes
  Group Policy - by default-site2site
  No vpn-addr-assign aaa
  No dhcp vpn-addr-assign
  Telnet timeout 5
  !
   

  The VPN is OK? ("' isakmp crypto to show his" should show a MM_Active tunnel to the peer address ")

  Normally exempt us VPN site-to-site of NAT traffic. This could be your problem. If you can share your configuration, we can have a look.

  p.s. you should affect the question of the security / VPN forum.

• With an ASA 5520 port forwarding

  Hi all

  I recently bought a Cisco ASA 5520 on eBay for study and I decided to only use it as a firewall between my home LAN and Internet. Wow, what a learning curve! I managed to add my internal networks as objects and create a rule (thanks to youtube) NAT to PAT my internal devices out of the Internet with ASSISTANT Deputy Ministers, but I am really struggling to do the following:-

  -allow all incoming traffic that hits the outside interface for port 38921 and nat at 10.1.10.101:38921

  -allow all incoming traffic that hits the outside interface for port 30392 and nat at 10.1.10.101:30392

  Can someone guide me on how to do it, because I have a couple of services that run behind these ports on a server I want to get when I'm not at home? My (rather messy) config is as follows:-

  hostname FW1

  activate the encrypted password

  encrypted passwd

  names of

  !

  interface GigabitEthernet0/0

  Description * externally facing Internet *.

  nameif outside

  security-level 0

  IP address dhcp setroute

  !

  interface GigabitEthernet0/1

  Description * internal face to 3750 *.

  nameif inside

  security-level 100

  IP 10.1.10.2 255.255.255.0

  !

  interface GigabitEthernet0/2

  Shutdown

  No nameif

  no level of security

  no ip address

  !

  interface GigabitEthernet0/3

  Shutdown

  No nameif

  no level of security

  no ip address

  !

  interface Management0/0

  nameif management

  security-level 100

  IP 192.168.1.1 255.255.255.0

  !

  passive FTP mode

  the VLAN1 object network

  subnet 192.168.1.0 255.255.255.0

  Legacy description

  network of the WiredLAN object

  10.1.10.0 subnet 255.255.255.0

  Wired LAN description

  network of the CorporateWifi object

  10.1.160.0 subnet 255.255.255.0

  Company Description 160 of VLAN wireless

  network of the GuestWifi object

  10.1.165.0 subnet 255.255.255.0

  Description Wireless VLAN 165 comments

  network of the LegacyLAN object

  subnet 192.168.1.0 255.255.255.0

  Description Legacy LAN in place until the change on

  the file server object network

  Home 10.1.10.101

  Description File Server

  service object Service1

  tcp source eq eq 38921 38921 destination service

  1 service Description

  the All_Inside_Networks object-group network

  network-object VLAN1

  network-object, object WiredLAN

  network-object, object CorporateWifi

  network-object, object GuestWifi

  network-object, object LegacyLAN

  object-group service Service2 tcp - udp

  port-object eq 30392

  object-group service DM_INLINE_TCPUDP_1 tcp - udp

  port-object eq 30392

  Group-object Service2

  object-group Protocol TCPUDP

  object-protocol udp

  object-tcp protocol

  Outside_access_in list extended access allowed object-group TCPUDP any inactive FileServer object-group DM_INLINE_TCPUDP_1 object

  Outside_access_in list extended access allowed object Service1 any inactive FileServer object

  pager lines 24

  Enable logging

  asdm of logging of information

  Outside 1500 MTU

  MTU 1500 internal

  management of MTU 1500

  no failover

  ICMP unreachable rate-limit 1 burst-size 1

  ASDM image disk0: / asdm - 714.bin

  don't allow no asdm history

  ARP timeout 14400

  service interface NAT (inside, outside) dynamic source FileServer Service1 inactive Service1

  NAT (all, outside) interface dynamic source All_Inside_Networks

  Access-group Outside_access_in in interface outside

  Internal route 10.1.160.0 255.255.255.0 10.1.10.1 1

  Internal route 10.1.165.0 255.255.255.0 10.1.10.1 1

  Internal route 192.168.1.0 255.255.255.0 10.1.10.1 1

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  timeout tcp-proxy-reassembly 0:01:00

  Floating conn timeout 0:00:00

  dynamic-access-policy-registration DfltAccessPolicy

  identity of the user by default-domain LOCAL

  Enable http server

  http 10.1.160.15 255.255.255.255 internal

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start

  Telnet 10.1.160.15 255.255.255.255 internal

  Telnet timeout 5

  SSH timeout 5

  Console timeout 0

  interface ID client DHCP-client to the outside

  management of 192.168.1.2 - dhcpd address 192.168.1.254

  enable dhcpd management

  !

  a basic threat threat detection

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  WebVPN

  username privilege of encrypted password of Barry 15

  !

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  maximum message length automatic of customer

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the preset_dns_map dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  inspect the rsh

  inspect the rtsp

  inspect esmtp

  inspect sqlnet

  inspect the skinny

  inspect sunrpc

  inspect xdmcp

  inspect the sip

  inspect the netbios

  inspect the tftp

  Review the ip options

  !

  global service-policy global_policy

  context of prompt hostname

  no remote anonymous reporting call

  Cryptochecksum:19be38edefe8c3fd05e720aedee62c8e

  : end

  1. This is just one example of configuration and another option with to reason and avoid to send us the complete configuration of NAT:

  network of the 10.1.10.101 object

  Home 10.1.10.101

  service object 38921

  tcp source eq 38921 service

  service object 30392

  tcp source eq 30392 service

  NAT (inside, outside) 1 static source 10.1.10.101 38921 38921 service interface

  NAT (inside, outside) 1 static source 10.1.10.101 30392 30392 service interface

  Let me know if it works

• VPN site to site & outdoor on ASA 5520 VPN client

  Hi, I'm jonathan rivero.

  I have an ASA 5520 Version 8.0 (2), I configured the site-to-site VPN and works very well, in the other device, I configured the VPN Client for remote users and works very well, but I try to cofigure 2 VPNs on ASA 5520 on the same outside interface and I have the line "outside_map interface card crypto outdoors (for VPN client). , but when I set up the "crypto map VPNL2L outside interface, it replaces the command', and so I can have only a single connection.

  the executed show.

  ASA1 (config) # sh run

  : Saved

  :

  ASA Version 8.0 (2)

  !

  hostname ASA1

  activate 7esAUjZmKQSFDCZX encrypted password

  names of

  !

  interface Ethernet0/0

  nameif inside

  security-level 100

  address 172.16.3.2 IP 255.255.255.0

  !

  interface Ethernet0/1

  nameif outside

  security-level 0

  IP 200.20.20.1 255.255.255.0

  !

  interface Ethernet0/1.1

  VLAN 1

  nameif outside1

  security-level 0

  no ip address

  !

  interface Ethernet0/2

  Shutdown

  No nameif

  no level of security

  no ip address

  !

  interface Ethernet0/3

  Shutdown

  No nameif

  no level of security

  no ip address

  !

  interface Ethernet0/4

  Shutdown

  No nameif

  no level of security

  no ip address

  !

  interface Ethernet0/5

  Shutdown

  No nameif

  no level of security

  no ip address

  !

  2KFQnbNIdI.2KYOU encrypted passwd

  passive FTP mode

  object-group, net-LAN

  object-network 172.16.0.0 255.255.255.0

  object-network 172.16.1.0 255.255.255.0

  object-network 172.16.2.0 255.255.255.0

  object-network 172.16.3.0 255.255.255.0

  object-group, NET / remote

  object-network 172.16.100.0 255.255.255.0

  object-network 172.16.101.0 255.255.255.0

  object-network 172.16.102.0 255.255.255.0

  object-network 172.16.103.0 255.255.255.0

  object-group network net-poolvpn

  object-network 192.168.11.0 255.255.255.0

  access list outside nat extended permit ip net local group object all

  access-list extended sheep allowed ip local object-group net object-group net / remote

  access-list extended sheep allowed ip local object-group net net poolvpn object-group

  access-list splittun-vpngroup1 extended permitted ip local object-group net net poolvpn object-group

  pager lines 24

  Within 1500 MTU

  Outside 1500 MTU

  outside1 MTU 1500

  IP local pool ippool 192.168.11.1 - 192.168.11.100 mask 255.255.255.0

  no failover

  ICMP unreachable rate-limit 100 burst-size 10

  don't allow no asdm history

  ARP timeout 14400

  Global 1 interface (outside)

  NAT (inside) 0 access-list sheep

  NAT (inside) 1 access list outside nat

  Route outside 0.0.0.0 0.0.0.0 200.20.20.1 1

  Route inside 172.16.0.0 255.255.255.0 172.16.3.2 1

  Route inside 172.16.1.0 255.255.255.0 172.16.3.2 1

  Route inside 172.16.2.0 255.255.255.0 172.16.3.2 1

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout, uauth 0:05:00 absolute

  dynamic-access-policy-registration DfltAccessPolicy

  the ssh LOCAL console AAA authentication

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown cold start

  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

  86400 seconds, duration of life crypto ipsec security association

  Crypto ipsec kilobytes of life security-association 400000

  Crypto-map dynamic outside_dyn_map 20 the value transform-set ESP-3DES-SHA

  card crypto VPNL2L 1 match for sheep

  card crypto VPNL2L 1 set peer 200.30.30.1

  VPNL2L 1 transform-set ESP-3DES-MD5 crypto card game

  map outside_map 65535-isakmp ipsec crypto dynamic outside_dyn_map

  outside_map interface card crypto outside

  crypto isakmp identity address

  crypto ISAKMP allow outside

  crypto ISAKMP policy 20

  preshared authentication

  3des encryption

  md5 hash

  Group 2

  life 86400

  crypto ISAKMP policy 30

  preshared authentication

  aes-256 encryption

  sha hash

  Group 2

  life 86400

  crypto ISAKMP policy 65535

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  Telnet timeout 5

  SSH timeout 5

  Console timeout 0

  a basic threat threat detection

  Statistics-list of access threat detection

  !

  !

  internal vpngroup1 group policy

  attributes of the strategy of group vpngroup1

  banner value +++ welcome to Cisco Systems 7.0. +++

  value of 192.168.0.1 DNS server 192.168.1.1

  Split-tunnel-policy tunnelspecified

  Split-tunnel-network-list value splittun-vpngroup1

  value by default-ad domain - domain.local

  Split-dns value ad - domain.local

  the address value ippool pools

  username password asa1 VRTlLlJ48/PoDKjS encrypted privilege 15

  tunnel-group 200.30.30.1 type ipsec-l2l

  IPSec-attributes tunnel-group 200.30.30.1

  pre-shared-key *.

  type tunnel-group vpngroup1 remote access

  tunnel-group vpngroup1 General-attributes

  ippool address pool

  Group Policy - by default-vpngroup1

  vpngroup1 group of tunnel ipsec-attributes

  pre-shared-key *.

  context of prompt hostname

  Cryptochecksum:00000000000000000000000000000000

  : end

  ASA2 (config) #sh run

  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
  86400 seconds, duration of life crypto ipsec security association
  Crypto ipsec kilobytes of life security-association 400000
  card crypto VPNL2L 1 match for sheep
  card crypto VPNL2L 1 set peer 200.30.30.1
  VPNL2L 1 transform-set ESP-3DES-MD5 crypto card game
  VPNL2L interface card crypto outside
  crypto isakmp identity address
  crypto ISAKMP allow outside
  crypto ISAKMP policy 20
  preshared authentication
  3des encryption
  md5 hash
  Group 2
  life 86400

  tunnel-group 200.30.30.1 type ipsec-l2l
  IPSec-attributes tunnel-group 200.30.30.1
  pre-shared key cisco

  my topology:

  

  I try with the following links, but did not work

  http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a0080912cfd.shtml

  http://www.Cisco.com/en/us/products/ps6120/products_tech_note09186a00807e0aca.shtml

  Best regards...

  "" I thing both the force of the SAA with the new road outside, why is that? ".

  without the road ASA pushes traffic inward, by default.

  In any case, this must have been a learning experience.

  Hopefully, this has been no help.

  Please rate, all the helful post.

  Thank you

  Rizwan Muhammed.

• ASA 5520 and MPF

  Hi all. In our company we have recently upgraded our PIX 515 firewall to ASA 5520, and we started to live a thing strange event. On one of the sites we host, I saw a lot of outdated SSM messages popping up and I think that they are the source of the problem when they surf the site (mainly surfing works fine, but sometimes people cannot content etc.).

  I found the Cisco solution for this problem by using the MPF, but one thing confuses me. If I ask a MPF allowing adults MSS on the external interface of the ASA does this political conflict with the comprehensive policy that is on the SAA by default or can they both at the same time?

  Thanks in advance for any help.

  You can have a single policy per interface and another - global, that by default applies to default-inspection-traffic.

  See http://www.cisco.com/en/US/docs/security/asa/asa80/configuration/guide/mpc.html for more details.

• ASA 5520 to Juniper ss505m vpn

  I'm having a problem with the vpn site to site between a asa 5520 and Juniper ss 505 m. The tunnel rises, but we seem unable to pass traffic through the vpn tunnel.  It appears on the remote side makes a connection to the ftp server on the Local Server, but is never prompt identification of connection information.

  April 19, 2016 13:27:13 SQL-B2B-01: % ASA-4-402116: IPSEC: received a package ESP x.x (SPI = 0xD167A5E8, sequence number = 0xD).

  241.90 (user = X.X.241.90) at X.X.167.230.  Inside the package décapsulés does not match policy negotiated in the SA.  The

  package specifies its destination as its Protocol TCP, its source such as X.X.2.68 and X.X.167.233.  SA specifies its loc

  proxy of Al X.X.167.233/255.255.255.255/tcp/5376 and his remote_proxy as X.X.2.68/255.255.255.255/tcp/5376.

  list of remote ip-group of objects allowed extended West Local Group object

  NAT static Local_Pub Local destination (indoor, outdoor) static source Remote

  Crypto ipsec ikev1 transform-set esp-aes-256 Remote esp-sha-hmac

  West-map 95 crypto card is the Remote address
  card crypto West-map 95 set peer X.X.241.90
  map West-map 95 set transform-set Remote ikev1 crypto
  card crypto West-map 95 defined security-association life seconds 28800

  Juniper-

  "Remote-ftp" X.X.167.233 255.255.255.255

  Gateway proposal P1 preshare "[email protected]/ * /" proposal "pre-g2-aes256-sha-28800.

  P2-proposal "no-pfs-esp-aes256-sha-28800" No. - pfs esp aes256 sha-1 second 28800

  ----------------------

  the top of the policy of "Trust" to "Untrust" "X.X.2.68/32" "Remote-ftp' 'ftp' vpn"Remote-vpn"tunnel log

  put on top of the "Untrust" policy to the "Trust" "Remote-ftp' 'X.X.2.68/32' 'ftp' vpn"SonoraQ-vpn"tunnel sign

  I do not know Juniper, but it seems that it is trying to negotiate the use of only 5376/tcp on the tunnel, when it should be negotiated just Protocol "ip".

• ASA 5520 Infiltration of DNS query

  Is the operation of TCPDUMP, simular to Sindwinder FW (example below), possible through ASA 5520 and AIP-SSM-10 (IPS) module? Reference and the answer to my question are appreciated.

  •tcpdump options for DNS

  -Internal Burba: tcpdump - ntpi em0 port 53

  -External Burba: tcpdump - ntpi em1 port 53

  tcpdump for SMTP options:

  Burba internal: tcpdump - ntpi em0 port 25

  External Burba: tcpdump - ntpi em1 port 25

  You can use the iplog command to capture a PCAP file on the module AIP - SSM (assuming that you sent the traffic you with capture or through the module AIP - SSM IPS). It will capture based on the source IP address.

  http://www.Cisco.com/en/us/docs/security/IPS/6.0/command/reference/crCmds.html#wp466857

  If you want TCPdump granularity, make a service account on the sensor, open a session in the Linux system, able to root and tcpdump away.

• ASA 5520 8.0 (4) port depending on the ACLs vpn works not

  Hi all

  I have a problem with an ASA (5520 8.0 (4)) for lack of working with a port based acl for remote clients. I have a simple acl from a single line to split traffic, if I allowed the tunnel IP works fine, if I lock it up to TCP 3389 rdp will not work. I don't see anything in the logs and debug output, I did have a problem with a similar configuration (5510 8.0 (4) and I'm at a loss to explain it.)

  Everyone knows about this problem before? I have nat exclusions etc and as I said, the tunnel only works if the acl permits all IP traffic between client and server.

  THX in advance

  Split-tunnel list cannot IP, if you want to restrict which ports are are sent via the tunnel vpn for your clients vpn, you need to use VPN filters under Group Policy:

  http://www.Cisco.com/en/us/products/HW/vpndevc/ps2030/products_configuration_example09186a00808c9a87.shtml

• ASA 5520: Remote VPN Clients cannot ping LAN, Internet

  I've set up a few of them in my time, but I am confused with this one.  Can I establish connect via VPN tunnel but I can't ping or go on the internet.  I searched the forum for similar and found a little issues, but none of the fixes seem to match.  I noticed a strange thing is when I run ipconfig/all of the vpn client, the IP address that has been leased over the Pool of the VPN is also the default gateway!

  I have attached the config.  Help, please.

  Thank you!

  Exemption of NAT ACL has not yet been applied.

  NAT (inside) 0-list of access Inside_nat0_outbound

  In addition, you have not split tunnel, not sure you were using internet ASA for the vpn client internet browsing.

  You can also enable icmp inspection if you test in scathing:

  Policy-map global_policy
  class inspection_default

  inspect the icmp

  Hope that helps.