Pool AnyConnect ip change

Similar Questions

• Access via L2L AnyConnect VPN IPSec

  I'm trying to connect two ASA 5505s for a IPSec L2L VPN.  They can connect, but not pass traffic from the AnyConnect subnet. I've added the config from ASA-2, with the LAN subnet of 192.168.138.0 and a subnet of 192.168.238.0 for AnyConnect client. I'm trying to get the AnyConnect Clients access to the 192.168.137.0 LAN behind ASA-1 at 1.1.1.1.  Having both 192.168.238.0 and 192.168.138.0 both access 192.168.137.0 is acceptable. There's probably a lot of cruft in this config, as I've been reading all over forums and docs without much success.  Can someone point me in the right direction? : ASA Version 8.2(1) ! hostname asa-wal names name 192.168.238.0 anyconnect-vpn ! interface Vlan1 nameif inside security-level 100 ip address 192.168.138.1 255.255.255.0 ! interface Vlan11 mac-address c03f.0e3b.1923 nameif outside security-level 0 ip address 2.2.2.2 255.255.255.248 ! same-security-traffic permit inter-interface same-security-traffic permit intra-interface object-group protocol TCPUDP protocol-object udp protocol-object tcp object-group service Munin tcp-udp port-object eq 4949 object-group service Webmin tcp port-object eq 10000 access-list inside_nat0_outbound extended permit ip 192.168.138.0 255.255.255.0 any access-list icmp_ping extended permit icmp any any echo-reply access-list icmp_ping extended permit ip 192.168.138.0 255.255.255.0 any access-list split-tunnel standard permit 192.168.138.0 255.255.255.0 access-list 100 extended permit icmp any any echo-reply access-list 100 extended permit icmp any any time-exceeded access-list 100 extended permit icmp any any unreachable access-list NO_NAT extended permit ip anyconnect-vpn 255.255.255.0 any access-list NONAT extended permit ip 192.168.138.0 255.255.255.0 anyconnect-vpn 255.255.255.0 access-list outside_access_in extended permit tcp any interface outside eq ssh access-list outside_access_in extended permit icmp any any echo-reply access-list outside_access_in extended permit icmp any any time-exceeded access-list outside_access_in extended permit icmp any any unreachable  access-list outside_access_in extended permit tcp 192.168.137.0 255.255.255.0 anyconnect-vpn 255.255.255.0 access-list outside_1_cryptomap extended permit ip anyconnect-vpn 255.255.255.0 192.168.137.0 255.255.255.0 access-list inside_nat0_outbound_1 extended permit ip 192.168.138.0 255.255.255.0 anyconnect-vpn 255.255.255.0 access-list inside_nat0_outbound_1 extended permit ip anyconnect-vpn 255.255.255.0 192.168.137.0 255.255.255.0 access-list LAN_Traffic extended permit ip anyconnect-vpn 255.255.255.0 192.168.137.0 255.255.255.0 access-list vpn_nonat extended permit ip anyconnect-vpn 255.255.255.0 192.168.137.0 255.255.255.0 ip local pool AnyConnect 192.168.238.101-192.168.238.125 mask 255.255.255.0 global (outside) 1 interface nat (inside) 0 access-list NONAT nat (inside) 2 access-list vpn_nonat nat (inside) 1 0.0.0.0 0.0.0.0 static (inside,outside) tcp interface ssh 192.168.138.4 ssh netmask 255.255.255.255 access-group icmp_ping in interface inside access-group outside_access_in in interface outside route outside 0.0.0.0 0.0.0.0 2.2.2.1 1 dynamic-access-policy-record DfltAccessPolicy network-acl inside_nat0_outbound network-acl NO_NAT aaa authentication ssh console LOCAL http server enable http bobx-vpn 255.255.255.0 inside http 192.168.137.0 255.255.255.0 inside http 192.168.1.104 255.255.255.255 inside http 192.168.138.0 255.255.255.0 inside http anyconnect-vpn 255.255.255.0 inside http redirect outside 80 no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto ipsec transform-set Wal2Box esp-aes-256 esp-sha-hmac crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto map outside_map 1 match address outside_1_cryptomap crypto map outside_map 1 set pfs group1 crypto map outside_map 1 set peer 98.110.179.36 crypto map outside_map 1 set transform-set ESP-3DES-SHA crypto map Wal2Box 1 match address LAN_Traffic crypto map Wal2Box 1 set peer 98.110.179.36 crypto map Wal2Box 1 set transform-set Wal2Box crypto map Wal2Box interface outside crypto isakmp enable outside crypto isakmp policy 1 authentication pre-share encryption aes-256 hash sha group 2 lifetime 86400 crypto isakmp policy 5 authentication pre-share encryption 3des hash sha group 2 lifetime 86400 crypto isakmp policy 10 authentication pre-share encryption des hash sha group 2 lifetime 86400 crypto isakmp nat-traversal 22 telnet timeout 5 ssh 192.168.138.0 255.255.255.0 inside ssh timeout 30 console timeout 0 management-access inside dhcpd dns 8.8.8.8 8.8.4.4 dhcpd auto_config outside ! dhcpd address 192.168.138.101-192.168.138.132 inside dhcpd dns 8.8.8.8 8.8.4.4 interface inside dhcpd lease 86400 interface inside dhcpd domain inc.internal interface inside dhcpd enable inside ! threat-detection basic-threat threat-detection statistics access-list no threat-detection statistics tcp-intercept ntp server 129.6.15.29 ntp server 129.6.15.28 prefer webvpn enable inside enable outside anyconnect-essentials svc image disk0:/anyconnect-win-2.4.1012-k9.pkg 1 svc enable tunnel-group-list enable group-policy DfltGrpPolicy attributes vpn-filter value NO_NAT vpn-tunnel-protocol IPSec l2tp-ipsec svc webvpn split-tunnel-network-list value split-tunnel webvpn   svc compression deflate group-policy Wal-AnyConnect internal group-policy Wal-AnyConnect attributes split-tunnel-policy tunnelspecified split-tunnel-network-list value split-tunnel tunnel-group DefaultRAGroup general-attributes address-pool AnyConnect default-group-policy Wal-AnyConnect strip-realm strip-group tunnel-group AnyConnectClientProfile type remote-access tunnel-group AnyConnectClientProfile general-attributes address-pool AnyConnect default-group-policy Wal-AnyConnect tunnel-group AnyConnectClientProfile webvpn-attributes group-alias AnyConnectVPNClient enable tunnel-group 1.1.1.1 type ipsec-l2l tunnel-group 1.1.1.1 ipsec-attributes pre-shared-key * ! class-map global-class match default-inspection-traffic ! ! policy-map global-policy class global-class   inspect pptp ! Cryptochecksum:762f0186ad987cda4b450f6b4929cb60 : end 

  Post edited by: Shawn Barrick - line breaks

  It seems good Shawn but I just noticed an error on the asa-wal, you have a vpn-filter applied on the DfltGrpPolicy and since you have not any value defined the strategy of Wal-AnyConnect group then will inherit the DfltGrpPolicy vpn-filter, don't forget that the vpn filters should be applied to the incoming direction, I mean pool resources you want them to have access to. It's the ACL you have for the filter:

  NO_NAT list extended access allowed anyconnect vpn - ip 255.255.255.0 everything

  This isn't in the inbound direction, increasingly looks like you want to allow access to what it is as long as the traffic is coming from the 192.168.238.0, if that's the case, you can do this:

  attributes of Group Policy DfltGrpPolicy

  VPN-filter no

  Do not forget to disconnect and reconnect after the above change...

  If you really need to be more specific, allowing traffic for clients then apply the inbound rules, for example:

  Your pool is here 192.168.238.0/24 and the local subnet is 192.168.138, to this effect, the 192.168.137 is considered to be local too because of the perspective Anyconnect we'll see in the room even if it is a remote network accessible via a L2L tunnel of the Anyconnect client does not.

  The following AS will allow the Anyconnect Telnet client for local networks:

  permit access-list vpnfilt-ra 192.168.238.0 255.255.255.255 192.168.138.0 255.255.255.0 eq 23

  permit access-list vpnfilt-ra 192.168.238.0 255.255.255.255 192.168.137.0 255.255.255.0 eq 23

  The following ACE will allow local networks of Telnet for the Anyconnect Client:

  permit access-list vpnfilt-ra 192.168.238.0 255.255.255.255 eq 23 192.168.138.0 255.255.255.0

  permit access-list vpnfilt-ra 192.168.238.0 255.255.255.255 eq 23 192.168.137.0 255.255.255.0

  Note that the two first ACE will allow LAN launch connection to the Anyconnect client on any TCP port if he uses a source 23 port while the last two ACEs allow the Anyconnect client connect to networks the on any TCP port if he uses a port source from 23.

  Kind regards

• AnyConnect Session Timeout issue

  We have some remote users that are not happy with the SSL Connect connection down after close their laptops or lose their wireless for once. I read this question and answer of a Cisco page and I was wondering where the session time-out setting is changed. It's on the network client, software map AnyConnect or ASA firewall?

  Thank you, Pat.

  Q. What is the AnyConnect reconnect behavior?

  A. AnyConnect will attempt to reconnect if the connection is interrupted. This behavior is not configurable and auto. As long as the session on the SAA is still valid, the session will resume if AnyConnect can restore the physical connection.

  Version 2.2 includes a roaming feature that allows AnyConnect reconnect after a sleep of PC. The client will continue to try indefinitely until the head told him he can't reconnect and the client will not immediately RIP into the tunnel when the system goes Standby/Hibernate implementation. For customers who don't want this feature, set the session timeout value low to prevent sleep or resume reconnects.

  And also, for the new AnyConnect profile changes take effect, you will need to reconnect your AnyConnect session if the new policy is pushed to the client.

• AnyConnect VPN

  Hello

  I have configured AnyConnect VPN with split tunneling, so my internal networks is in the tunnel and get internet directly (not via an internal network).

  But we want to access one of the public IP (8.8.8.8) through AnyConnect VPN tunnel.

  When we check the capture of packets on an external interface, trying to ping 8.8.8.8 showing the icmp-request package but not get icmp-response packages.

  Additional configuration required to access the ip address above by tunnel?

  We have activated the below configuration as well.

  permit same-security-traffic intra-interface

  permit same-security-traffic inter-interface

  Please find details of the capture below: 192.168.18.71 is my ip from the pool AnyConnect VPN system.

  114 extended access-list allow ip host 192.168.18.71 8.8.8.8
  115 extended access-list allow host 8.8.8.8 ip 192.168.18.71

  output interface of capture within the list of access-114
  Capture interface entering inside the access-list 115

  See the capture of xxx - ASA (config) # outgoing

  1: 22:13:24.001800 192.168.18.71 > 8.8.8.8: icmp: echo request
  2: 22:13:28.986139 192.168.18.71 > 8.8.8.8: icmp: echo request
  3: 22:13:33.970561 192.168.18.71 > 8.8.8.8: icmp: echo request
  4: 22:13:38.971156 192.168.18.71 > 8.8.8.8: icmp: echo request
  5: 22:13:44.080058 192.168.18.71 > 8.8.8.8: icmp: echo request
  5 packs shown
  XXX - ASA (config) #.
  XXX - ASA (config) #.
  XXX - ASA (config) # display incoming capture

  0 packets captured

  0 illustrated package
  XXX - ASA (config) # display incoming capture

  0 packets captured

  0 illustrated package

  Kindly help us solve the problem.

  Thank you and best regards,

  Ashok

  I like to use the notation NAT object instead.  So maybe try:

  object network obj-192.168.18.0  nat (outside,outside) dynamic interface

• Cisco Anyconnect access problem

  I configured Anyconnect VPN. I can connect to the VPN from outside successfully but can not ping on my server or map the shared folder.

  can someone take a look at the configuration of firewall and help out me.

  ASA 9.1 Version 2
  !
  hostname DASA2
  domain JDSYINGAA.com
  activate 8Ry2YjIyt7RRXU24 encrypted password
  names of
  mask 192.168.78.1 - 192.168.78.254 255.255.255.0 IP local pool Abe_VPN
  !
  interface GigabitEthernet0/0
  nameif inside
  security-level 100
  IP 192.168.10.1 255.255.255.0
  !
  interface GigabitEthernet0/1
  nameif outside
  security-level 0
  IP 13.15.13.60 255.255.255.0
  !
  interface GigabitEthernet0/2
  nameif DMZ
  security-level 10
  address 192.168.20.1 255.255.255.0
  !
  interface GigabitEthernet0/3
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface GigabitEthernet0/4
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface GigabitEthernet0/5
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface Management0/0
  management only
  nameif management
  security-level 100
  192.168.5.1 IP address 255.255.255.0
  !
  passive FTP mode
  clock timezone IS - 5
  clock to summer time EDT recurring
  DNS server-group DefaultDNS
  domain JDSYINGAA.com
  permit same-security-traffic inter-interface
  permit same-security-traffic intra-interface
  network of the NETWORK_OBJ_192.168.78.0_24 object
  192.168.78.0 subnet 255.255.255.0
  object-group network
  object-network 192.168.10.0 255.255.255.0
  pager lines 24
  Enable logging
  asdm of logging of information
  management of MTU 1500
  Within 1500 MTU
  Outside 1500 MTU
  MTU 1500 DMZ
  ICMP unreachable rate-limit 1 burst-size 1
  don't allow no asdm history
  ARP timeout 14400
  no permit-nonconnected arp
  NAT (inside, outside) static source any any static destination NETWORK_OBJ_192.168.78.0_24 NETWORK_OBJ_192.168.78.0_24 non-proxy-arp-search to itinerary
  !
  NAT automatic interface after (indoor, outdoor) dynamic source
  Route outside 0.0.0.0 0.0.0.0 13.15.13.1 1
  Timeout xlate 03:00
  Pat-xlate timeout 0:00:30
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00
  Floating conn timeout 0:00:00
  dynamic-access-policy-registration DfltAccessPolicy
  AAA-server JDSYINGAA.com Protocol nt
  AAA-server host 192.168.10.2 (inside) JDSYINGAA.com
  Timeout 5
  auth-JDSYINGAA.com NT domain controller
  identity of the user by default-domain LOCAL
  Enable http server
  http 192.168.5.0 255.255.255.0 management
  No snmp server location
  No snmp Server contact
  Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start
  Crypto ipsec pmtu aging infinite - the security association
  Crypto ca trustpoint _SmartCallHome_ServerCA
  Configure CRL
  trustpool crypto ca policy
  Crypto ca certificate chain _SmartCallHome_ServerCA
  certificate ca 6ecc7aa5a7032009b8cebcf4e952d491
  308204 4 a0030201 d 308205ec 0202106e cc7aa5a7 032009b 8 cebcf4e9 52d 49130
  010105 05003081 09060355 04061302 55533117 ca310b30 0d 864886f7 0d06092a
  30150603 55040 has 13 0e566572 69536967 6e2c2049 6e632e31 1f301d06 0355040b
  13165665 72695369 676e2054 72757374 204e6574 776f726b 313 has 3038 06035504
  0b 133128 63292032 30303620 56657269 5369676e 2c20496e 632e202d 20466f72
  20617574 7a 656420 75736520 6f6e6c79 31453043 06035504 03133c 56 686f7269
  65726953 69676e20 436c 6173 73203320 5075626c 69632050 72696 72792043 61 d
  65727469 66696361 74696f6e 20417574 686f7269 7479202d 20473530 1e170d31
  30303230 38303030 3030305a 170d 3230 30323037 32333539 35395a 30 81b5310b
  30090603 55040613 02555331 17301506 0355040a 130e5665 72695369 676e2c20
  496e632e 311f301d 06035504 0b 131656 65726953 69676e20 54727573 74204e65
  74776f72 6b313b30 5465726d 20757365 20617420 73206f66 39060355 040b 1332
  68747470 7777772e 733a2f2f 76657269 7369676e 2e636f6d 2f727061 20286329
  302d 0603 55040313 26566572 69536967 61737320 33205365 6e20436c 3130312f
  63757265 20536572 76657220 20473330 82012230 0d06092a 864886f7 4341202d
  010101 05000382 010f0030 82010 0d has 02 b187841f 82010100 c20c45f5 bcab2597
  a7ada23e 9cbaf6c1 39b88bca c2ac56c6 e5bb658e 444f4dce 6fed094a d4af4e10
  9c688b2e 957b899b 13cae234 34c1f35b f3497b62 d188786c 83488174 0253f9bc
  7f432657 5833833b 330a17b0 d04e9124 ad867d64 12dc744a 34a11d0a ea961d0b
  15fca34b 3bce6388 d0f82d0c 948610ca b69a3dca eb379c00 48358629 5078e845
  1941 4ff595ec 7b98d4c4 71b350be 28b38fa0 b9539cf5 ca2c23a9 fd1406e8 63cd
  18b49ae8 3c6e81fd e4cd3536 b351d369 ec12ba56 6e6f9b57 c58b14e7 0ec79ced
  4a546ac9 4dc5bf11 b1ae1c67 81cb4455 33997f24 9b3f5345 7f861af3 3cfa6d7f
  81f5b84a d3f58537 1cb5a6d0 09e4187b 384efa0f 01 has 38201 02030100 df308201
  082b 0601 05050701 01042830 26302406 082 b 0601 db303406 05050730 01861868
  7474703a 2f2f6f63 73702e76 65726973 69676e2e 636f6d30 12060355 1 d 130101
  ff040830 02010030 70060355 b 200469 30673065 060, 6086 480186f8 1 d 060101ff
  45010717 03305630 2806082b 06010505 07020116 1 c 687474 70733a2f 2f777777
  2e766572 69736967 6e2e636f 6d2f6370 73302 has 06 082 b 0601 05050702 02301e1a
  1 c 687474 70733a2f 2f777777 2e766572 69736967 6e2e636f 6d2f7270 61303406
  03551d1f 042d302b 3029 has 027 a0258623 68747470 3a2f2f63 726c2e76 65726973
  69676e2e 636f6d2f 2d67352e 70636133 63726c 30 0e060355 1d0f0101 ff040403
  02010630 6d06082b 06010505 07010c 59305730 55160969 5da05b30 04 61305fa1
  6 d 616765 2f676966 3021301f 2b0e0302 30070605 1a04148f e5d31a86 ac8d8e6b
  c3cf806a d448182c 7b192e30 25162368 7474703a 2f2f6c6f 676f2e76 65726973
  69676e2e 636f6d2f 76736c6f 676f2e67 69663028 0603551d 11042130 1fa41d30
  1 b 311930 17060355 04031310 56657269 5369676e 4d504b49 2d322d36 301D 0603
  445 1653 44c1827e 1d20ab25 f40163d8 be79a530 1f060355 c 1604140d 551d0e04
  1 230418 30168014 7fd365a7 c2ddecbb f03009f3 4339fa02 af333133 300 d 0609 d
  2a 864886 05050003 82010100 0c8324ef ddc30cd9 589cfe36 b6eb8a80 f70d0101
  4bd1a3f7 9df3cc53 ef829ea3 a1e697c1 589d756c e01d1b4c fad1c12d 05c0ea6e
  b2227055 d9203340 3307c 265 83fa8f43 379bea0e 9a6c70ee f69c803b d937f47a
  99 c 71928 8705 404167d 1 273aeddc 866d 24f78526 a2bed877 7d494aca 6decd018
  481d22cd 0b0b8bbc f4b17bfd b499a8e9 762ae11a 2d876e74 d388dd1e 22c6df16
  b62b8214 0a945cf2 50ecafce ff62370d ad65d306 4153ed02 14c8b558 28a1ace0
  5becb37f 954afb03 c8ad26db e6667812 4ad99f42 fbe198e6 42839b8f 8f6724e8
  6119b5dd cdb50b26 058ec36e c4c875b8 46cfe218 065ea9ae a8819a47 16de0c28
  6c2527b9 deb78458 c61f381e a4c4cb66
  quit smoking
  Telnet timeout 5
  SSH timeout 5
  SSH group dh-Group1-sha1 key exchange
  Console timeout 0
  192.168.5.2 management - dhcpd addresses 192.168.5.254
  enable dhcpd management
  !
  a basic threat threat detection
  Statistics-list of access threat detection
  no statistical threat detection tcp-interception
  WebVPN
  allow inside
  allow outside
  AnyConnect essentials
  AnyConnect image disk0:/anyconnect-win-2.5.2014-k9.pkg 1
  AnyConnect enable
  tunnel-group-list activate
  internal GroupPolicy_abeone_VPN group strategy
  attributes of Group Policy GroupPolicy_abeone_VPN
  WINS server no
  value of the DNS-server 192.168.10.2
  client ssl-VPN-tunnel-Protocol
  value by default-field JDSYINGAA.com
  username privilege 15 encrypted password /oETeAnGnysKS53o mt
  type tunnel-group Abe_VPN remote access
  attributes global-tunnel-group Abe_VPN
  address pool Abe_VPN
  Group Policy - by default-GroupPolicy_AJDSYINGAA_VPN
  tunnel-group Abe_VPN webvpn-attributes
  enable Abe_VPN group-alias
  !
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  maximum message length automatic of customer
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  inspect the rsh
  inspect the rtsp
  inspect esmtp
  inspect sqlnet
  inspect the skinny
  inspect sunrpc
  inspect xdmcp
  inspect the sip
  inspect the netbios
  inspect the tftp
  Review the ip options
  !
  global service-policy global_policy
  context of prompt hostname
  call-home service
  anonymous reporting remote call
  call-home
  contact-email-addr [email protected] / * /
  Profile of CiscoTAC-1
  http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
  email address of destination [email protected] / * /
  destination-mode http transport
  Subscribe to alert-group diagnosis
  Subscribe to alert-group environment
  Subscribe to alert-group 27 monthly periodic inventory
  Subscribe to alert-group configuration periodic monthly 27
  daily periodic subscribe to alert-group telemetry
  Cryptochecksum:d4a18e6096befdad7d4d7748bcd52ea1
  : end
  don't allow no asdm history

  -See more at: https://supportforums.cisco.com/discussion/12541931/anyconnect-vpn#sthas...

  Here is my work anyconnect lab configuration.
  I deleted the obsolete lines

  interface GigabitEthernet0
  nameif inside
  security-level 100
  IP 10.10.10.1 255.255.255.0
  !
  interface GigabitEthernet1
  nameif outside
  security-level 0
  IP 20.20.20.1 255.255.255.252
  !

  the object to the Interior-net network
  10.10.10.0 subnet 255.255.255.0
  object subnet anyconnect-
  172.16.0.0 subnet 255.255.255.0
  standard access list permits 10.10.10.0 SPLIT-TUNNEL 255.255.255.0

  IP local pool anyconnect-172.16.0.10 - 172.16.0.20 mask 255.255.255.0

  NAT (inside, outside) static source any any destination static anyconnect subnet subnet anyconnect non-proxy-arp-search to itinerary

  the object to the Interior-net network
  NAT dynamic interface (indoor, outdoor)

  WebVPN
  allow outside
  AnyConnect image disk0:/anyconnect-win-3.1.05152-k9.pkg 1
  AnyConnect enable
  tunnel-group-list activate

  internal strategy of GP-PROFILE group
  GP-PROFILE group policy attributes
  value of server DNS 8.8.8.8
  Protocol-tunnel-VPN-client ssl clientless ssl
  Split-tunnel-policy tunnelspecified
  Split-tunnel-network-list value of SPLIT TUNNEL

  Auntie username attributes
  VPN-group-GP-PROFILE
  type of remote access service

  type TG-PROFILE tunnel-group remote access
  TG-PROFILE general-attributes tunnel-group
  anyconnect-pool address pool
  Group Policy - by default-GP-PROFILE
  TG-PROFILE webvpn-attributes tunnel-group
  enable TG-PROFILE Group-alias

  !
  class-map default_class
  match default-inspection-traffic
  !
  !
  Policy-map default_policy
  default_class class
  inspect the icmp
  !
  service-policy default_policy outside interface

• AnyConnect client has persistent settings after uninstall

  Usually, I'm able to type in the address field of client anyconnect and change to another client (we are a partner that support many people).

  For some reason any has my client anyconnect 'infranet-cm0' and 'infranet-cups"(our call manager and presence servers) in the connection to the domain, and you cannot type in this area. It makes no sense at all... Need just the certificates on my system or something.

  I uninstalled the client several times and launched from web client I am trying to connect to - download the new client, but he always comes back to the top with these two options to connect. I have attached a screenshot.

  How can I get rid of these options and allow me to be still able to type in the address?

  Have you tried to delete the profile?

  Client deployment paths

  OPERATING SYSTEM	The directory path
  Windows 7 and Vista	C:\ProgramData\Cisco\Cisco AnyConnect secure mobility Client\Profile\
  Windows XP	C:\Document and Settings\All Users\Application Data\Cisco\Cisco AnyConnect secure mobility Client\Profile
  Mac OS X and Linux	/ opt/cisco/anyconnect/profile /.

  http://www.Cisco.com/en/us/docs/security/vpn_client/AnyConnect/anyconnect31/Administration/Guide/ac02asaconfig.html#wp1595490

• AnyConnect secure mobility Client 3 + NFP

  Hello

  I have configured SSL on ASA 5540 VPN. The version of the client's Anyconnect Secure Mobility Client v3.0.0629

  Connection sessions works very well.

  I pushed the profile to customers with the Option start before logon.

  I want to try on Windows XP and 7 guests.

  For Windows XP

  In Cisco download the software, I have not found a version of SBL in this version:

  http://www.Cisco.com/Cisco/software/release.html?mdfid=283000185&flowid=17001&softwareid=282364313&release=3.0.0629&rellifecycle=&relind=available&RelType=latest

  The previous version, I found "anyconnect-gina-win-2.5.2019-pre-deploy-k9.msi" does not work with my client.

  A SBL msi there for this customer?

  For Windows 7

  According to http://www.cisco.com/en/US/docs/security/vpn_client/anyconnect/anyconnect22/administration/guide/22admin4.html#wp1008975

  I have to load an add-on.

  How can I do this? I can't find this add on.

  Thanks for your answers,

  Patrick

  Patrick,

  Did you get an answer on this one?

  I have not tried, but if I read the docs PLAP must be included in the installation package.

  BTW, the SBL package should be part of the package anyconnect (just change the extension of the 'package' to 'zip' and take a look inside).

  http://www.Cisco.com/en/us/docs/security/vpn_client/AnyConnect/anyconnect30/Administration/Guide/ac03vpn.html#wp1056595

  Marcin

• Client AnyConnect not getting the return traffic.

  Hi all

  I installing AnyConnect on a SAA and after successful authentication of the client, no traffic passes the firewall on the client. I don't get that packets sent, not received. The customer is sucessfully obtaining an address of the local swimming pool, but cannot go anyhere.

  The firewall log shows inside connections under construction... but that's all!

  TIA

  Dave

  If you can test the SAA, but not the gateway, it means that the bridge does not know how to get to the pool AnyConnect ip subnet.

  Please check the gateway and make sure that there is a route to the ASA interface for subnet pool AnyConnect.

• PS6210xs and PS6210x in the same pool?

  Hello. We have a hybrid of PS6210XS and two models of PS6210X in a group. They are all current firmware 8.1.4, and they are all in separate categories. The XS is running accelerated RAID6 and X models are running RAID6. Together, these models will all play in a pool despite the correct raid accelerated/no levels accelerated,?

  In addition, members use about 30 TB out of the 58 available to, but it is not evenly distributed. I know that I can not remove the default pool, but I want to put everything in one of the other pools. If I can move the Member Pool2 in Pool1 (and it doesn't look as if I had enough space in Pool1 to do), then, I can move the default pool member in Pool1 and leave default empty, correct?

  ETA: And remove Pool2 after this member is moved in Pool1, before moving the default pool member.

  Thank you.

  Hello

  First of all, you don't have to remove all of the pools.  You can always merge pools.  The change will happen immediately, but it will take time to balance the pages between members.

  I'm always careful about the fusion hybrid with other non-hybrid.  Sometimes, the hybrid is much smaller than the other members.  Especially in the case where the drives are NL - SAS.  Which tends to mitigate the benefits of the hybrid, being much more data on the NL - SAS members.

  I would like to look at SANHQ to see what the charges are of different members.

  If you decide to merge the members, I would like to start by merging the X models.  If you select a pool, there is an option "merge pools".  Then, you must select the Member that you want to add tot this pool.

  You can also open a support case and ask for help.  They can examine the data SANHQ and table diagnostics.

  Fusion of members is quite easy, it breaks the new, which can be more difficult.

  Kind regards

  Don

• Memory not fully usable in the pool allocation?

  Hello

  We have a few "issues" with Org CDV is deployed under the pool allocation model. It is not possible to use the RAM allocated by 100% (or any value close to 100%). When you try to start the virtual machines, we receive an error for the allocation of resources of the vCenter (lack of resources...). It turns out when you look at the list of resources that 'Used a reservation' is greater than the sum of reservation of the virtual machines that is already running.

  Example of

  Org vDC has 13 GB of RAM allocated with 20% guarantee = list of resources gets 2662 MB of booking

  VM1 is configured with 5 GB RAM = Gets a booking of 1024MB

  VM2 is configured with 6 GB of RAM = Gets a booking of 1229 MB

  Sum of reserves VM = 2253MB

  Customers point of view, it seems that there are always 2 GB available RAM, RP views (calculated) there are still the 409 MB available that are 20% of the 2 GB of RAM. If the client sets up a new virtual machine with 2 GB, tries to start, but it does not work because of insufficient resources.

  When you look at the list of resources in detail, that it's somehow clearly why it fails. The used reserve is 2521 MB, so only 141 MB are available. It is about 700 MB usable for the customer.

  I think it has to do with the charge of the virtual machines, although the General value of resource pools does not explain this difference

  This also occurs when you use other percentages of RAM guaranteed.

  This behavior is - although somewhat understandable - boring.

  To avoid calls to the technical support of customers complain about this issue (in my opinion), there are 2 possibilities

  1. explain the situation/reason for customer and tell them to order more RAM. First of all I don't think that the majority will understand it or worries. And as long as we can't calculate how it takes over is a no go.

  2. Add a buffer to the quantity of RAM. It's what we right now - we add 10%. It works, but customers see that they have more available RAM that they ordered. Integration with billing is too difficult.

  Other vCloud Director users are aware of this issue, too? STI is expected to 'fix' that in future releases? As vCloud Director auto setting RP booking limits somwhow.

  Best regards

  Carsten

  Is it in vCloud 5.1.2 or 5.1.0/5.1.1? If you're on 5.1.2 and using a single cluster for the allocation (inelastic) pools, you can force elastic mode.

  explanation here is for the memory usage:

  Allocation Pool organization VDC changes vCloud Director 5.1.2

• Change VM Namin Pattern

  I have just tried to change a naming VM for a VDI pool model by changing mode administrator and recompsing however he dd does not work. I don't see any change in the Admin to view, but not after the restructuring. I have to delete the pool and re-create it in order to make these types of changes?

  Try to remove some of these virtual desktops of the console administration view rather than reconstruct the.

• mass, manual update of the pools by script

  Hello

  I need to update about 200 pools manual to change the default RDP to pcoip Protocol.

  I know that the syntax with powershell:

  PS C:\Program VMware View\Server\bin > update-manualpool-pool_id myPool1 - defaultprotocol pcoip

  I myPool1 to myPool199 and want scipt that...

  Can you please help.

  Sorry, but I'm not a programmer

  Alex

  I use this code base to run a refresh on a bunch of pools that have a name that starts with certain characters.  Must go through all your pools and run the cmdlet you want to run.  As always test it first of all that your mileage may vary.

  foreach ($pool in (Get-pool-pool_id *)) { }
  -pool_id $pool.pool_id |
  }

  -Chris

• VPN ssl cannot access the internet

  Hello guys!

  I need help to allow access to the internet for my vpn users. I can connect with Anyconnect but do not have access to the internet. Subnet for VPN is 192.168.100.0. I welcomed this subnet on my cisco router.

  ISP-> router-> 192.168.0.0-> ASA-> 192.168.1.0 (887VA)

  Here is my config:

  ASA Version 9.1 (3)

  mask of local pool AnyConnect 192.168.100.1 - 192.168.100.254 IP 255.255.255.0

  network of the NETWORK_OBJ_192.168.100.0_24 object

  255.255.255.0 subnet 192.168.100.0

  NAT (inside, outside) static source any any static destination NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 non-proxy-arp-search to itinerary

  Trust SSL VPN outside

  Trust SSL VPN inside

  WebVPN

  allow inside

  allow outside

  AnyConnect image disk0:/anyconnect-win-3.1.04072-k9.pkg 1

  AnyConnect enable

  tunnel-group-list activate

  attributes of Group Policy DfltGrpPolicy

  L2TP ipsec ikev2 VPN-tunnel-Protocol

  internal GroupPolicy_VPN group strategy

  attributes of Group Policy GroupPolicy_VPN

  WINS server no

  client ssl-VPN-tunnel-Protocol

  Split-tunnel-policy tunnelall

  username alex Awards

  VPN-group-policy GroupPolicy_VPN

  VPN Tunnel-group type remote access

  General-attributes of VPN Tunnel-group

  address pool AnyConnect

  Group Policy - by default-GroupPolicy_VPN

  VPN Tunnel-group webvpn-attributes

  enable VPN group-alias

  Thank you very much!

  Hello

  Make sure you have this configuration

  permit same-security-traffic intra-interface

  You can check with

  See the race same-security-traffic

  If you don't have it then add it and test again.

  If this does not work after this then check if your router is to see all this traffic. For example you see any translation NAT on the router to your VPN users?

  What NAT configuration did you use for testing? I suggest 2 options above.

  First of all, one was to change the current VPN Client NAT0 configuration and dynamic addition PAT for VPN users to the Internet.

  Second, it was just to change the configuration of NAT0

  -Jouni

• R6220 routing between WIFI and LAN stops

  Hello

  I use the wifi netgear R6220 router. I have a few devices connected using LAN: TV, surveillance and desktop computer, but the computer is available only if UPS is running.

  TV is configured using DHCP, but has implemented monitoring static ip = 10.0.0.125.

  DHCP is configured to allow the address 10.0.0.2 - 10.0.0.50.

  the router configuration is reset to the factory, and only the LAN and DHCP address pool address has changed.

  Problem is that, after awhile, I cannot ping 10.0.0.125 (supervisory) WiFi.

  After that the router has been rrestarted and configured, it works for a while, and the next day I try to check video surveillance and ping do not work...

  I checked Wifi 2.4 and 5G.

  I also updated firmwqare to the last.

  Do anyone know of this problem, because I do not know if I would come back to router for seller or not.

  Thanks in advance.

  Peter.

  Forget the static use address reservations.

• do not access my home network via antconnect

  I am able to connect through the anyconnect client and get an ip address, but I am not able to access my administration (internal network)

  Administration = 10.18.1.120

  VPN pool = 172.16.10.0/28

  10.17.13.120 outside

  This is my config

  ASA 1.0000 Version 2
  !
  !
  interface GigabitEthernet0/0
  nameif administration
  security-level 100
  IP 10.18.1.120 255.255.0.0
  !
  interface GigabitEthernet0/1
  nameif outside
  security-level 0
  IP 10.17.13.120 255.255.0.0
  !
  interface GigabitEthernet0/2
  nameif admin-out13
  security-level 0
  IP 10.13.1.120 255.255.0.0
  !
  interface GigabitEthernet0/3
  nameif VOIP
  security-level 0
  IP 10.90.100.120 255.255.0.0
  !
  passive FTP mode
  network of the NETWORK_OBJ_172.16.10.0_29 object
  subnet 172.16.10.0 255.255.255.248
  network of the Admin_Email_Server object
  Home 10.18.4.120
  e-mail Description admin server
  network of the Admin_Srv_Farm object
  10.18.4.0 subnet 255.255.255.0
  Description subenet where the admin servers are hosted
  ICMP-type of object-group ICMP_Group
  alternate address ICMP-object
  ICMP-object-conversion error
  echo ICMP-object
  response to echo ICMP-object
  ICMP-object information-response
  ICMP-object-request for information
  ICMP object-mask-reply
  Mask-request ICMP-object
  ICMP-object mobile-redirect
  ICMP-object-parameter problem
  redirect ICMP-object
  ICMP-object-announcement of router
  ICMP-object-solicitation of router
  Object-ICMP source-quench
  ICMP-object has exceeded the time
  ICMP-object-response to timestamp
  Timestamp-request ICMP-object
  Object-ICMP traceroute
  ICMP-unreachable object
  object-group Protocol TCPUDP
  object-protocol udp
  object-tcp protocol
  pager lines 24
  Enable logging
  asdm of logging of information
  management of MTU 1500
  administration of MTU 1500
  Outside 1500 MTU
  Admin-out13 MTU 1500
  ip_phones MTU 1500
  local pool ADMIN_VPN_POOL 172.16.10.1 - 172.16.10.10 255.255.255.0 IP mask
  no failover
  ICMP unreachable rate-limit 1 burst-size 1
  ASDM image disk0: / asdm - 66114.bin
  don't allow no asdm history
  ARP timeout 14400
  NAT (administration, outside) static source any any static destination NETWORK_OBJ_172.16.10.0_29 NETWORK_OBJ_172.16.10.0_29 non-proxy-arp-search to itinerary
  public static NETWORK_OBJ_172.16.10.0_29 NETWORK_OBJ_172.16.10.0_29 destination NAT (outside directors) static source Admin_Srv_Farm Admin_Srv_Farm
  Timeout xlate 03:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00
  Floating conn timeout 0:00:00
  dynamic-access-policy-registration DfltAccessPolicy
  identity of the user by default-domain LOCAL
  LOCAL AAA authentication serial console
  AAA authentication LOCAL telnet console
  the ssh LOCAL console AAA authentication
  Enable http server
  http 10.18.0.0 255.255.0.0 administration
  No snmp server location
  No snmp Server contact
  Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start
  Crypto ipsec ikev2 ipsec-proposal OF
  encryption protocol esp
  Esp integrity sha - 1, md5 Protocol
  Crypto ipsec ikev2 proposal ipsec 3DES
  Esp 3des encryption protocol
  Esp integrity sha - 1, md5 Protocol
  Crypto ipsec ikev2 ipsec-proposal AES
  Esp aes encryption protocol
  Esp integrity sha - 1, md5 Protocol
  Crypto ipsec ikev2 ipsec-proposal AES192
  Protocol esp encryption aes-192
  Esp integrity sha - 1, md5 Protocol
  Crypto ipsec ikev2 AES256 ipsec-proposal
  Protocol esp encryption aes-256
  Esp integrity sha - 1, md5 Protocol
  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev2 AES256 AES192 AES 3DES ipsec-proposal OF
  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
  outside_map interface card crypto outside
  Crypto ca trustpoint ASDM_TrustPoint0
  registration auto
  name of the object CN = admin-pare-fire
  Configure CRL
  string encryption ca ASDM_TrustPoint0 certificates
   
  Crypto ikev2 activate out of service the customer port 443
  Crypto ikev2 access remote trustpoint ASDM_TrustPoint0
  Telnet timeout 5
  SSH timeout 5
  Console timeout 0
  dhcpd address 10.90.100.1 - 10.90.100.100 ip_phones
  dhcpd 4.2.2.2 dns 8.8.8.8 interface ip_phones
  dhcpd lease 1800 interface ip_phones
  dhcpd field uz.ac.zw interface ip_phones
  dhcpd option 3 ip 10.90.1.254 interface ip_phones
  ip_phones enable dhcpd
  !
  !
  maximum session 1000 TLS-proxy
  !
  a basic threat threat detection
  threat detection statistics
  a statistical threat detection tcp-interception rate-interval 30 burst-400-rate average rate 200
  SSL-trust outside ASDM_TrustPoint0 point
  WebVPN
  allow outside
  AnyConnect image disk0:/anyconnect-win-2.5.2014-k9.pkg 1
  AnyConnect image disk0:/anyconnect-macosx-i386-2.5.2014-k9.pkg 2
  AnyConnect profiles ITADMIN_VPN_client_profile disk0: / ITADMIN_VPN_client_profile.xml
  AnyConnect enable
  tunnel-group-list activate
  internal GroupPolicy_ITADMIN_VPN group strategy
  attributes of Group Policy GroupPolicy_ITADMIN_VPN
  WINS server no
  value of 10.18.4.120 DNS server 10.50.7.178
  client ssl-VPN-tunnel-Protocol ikev2
  uz.AC.ZW value by default-field
  WebVPN
  AnyConnect value ITADMIN_VPN_client_profile type user profiles
  webster nwgth7HVlZ/qiWnP password encrypted username
  webster username attributes
  type of remote access service
  username admin password encrypted xxxxxxxxxxx privilege 15
  username user2 encrypted password privilege 15 xxxxxxxxxxx
  attributes of user user2 name
  type of remote access service
  type tunnel-group ITADMIN_VPN remote access
  attributes global-tunnel-group ITADMIN_VPN
  address ADMIN_VPN_POOL pool
  Group Policy - by default-GroupPolicy_ITADMIN_VPN
  tunnel-group ITADMIN_VPN webvpn-attributes
  enable ITADMIN_VPN group-alias
  !
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  maximum message length automatic of customer
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  inspect the rsh
  inspect the rtsp
  inspect esmtp
  inspect sqlnet
  inspect the skinny
  inspect sunrpc
  inspect xdmcp
  inspect the sip
  inspect the netbios
  inspect the tftp
  Review the ip options
  class class by default
  Statistical accounting of user
  !
  global service-policy global_policy
  context of prompt hostname
  no remote anonymous reporting call
  Cryptochecksum:c9820a69d5b4fb9e3f7cce253f2450e4

  After the addition of administration management-access command, please check if you are able to ping to the administration interface (ip = 10.18.1.120) of the remote user's machine. In addition, run this command on the ASA.

  Packet-trace entry administration icmp 8 0 detailed

  Once you run this copy please order the output and the share here. Please see links to the ip address of the host, sitting behind the administration interface that you think that the ip address of the internal host should be able to ping from outside. Assigned ip address is the ip address that is assigned to the pool anyconnect client.

  Share the details here and we will be able to understand the question.

  Thank you

  Vishnu