Port forwarding works not, help

Similar Questions

• Port forwarding does not work on EA6900

  Please help me to know what is the reason for this port forwarding does not work on my Linksys router:

  Model: EA6900 v1.1
  Firmware version: 1.1.42.161129

  I've set up two ports: TCP 22 and 8070 TCP to 192.168.1.10. (192.168.1.10 is up and running, I can reach the LAN ports).

  Yesterday, I had a live chat with Linksys support we tried to re - download the firmware even, but that did not help. Then factory reset and reconfigure the router did not help either.

  Unchecking "Filter anonymous Internet requests" and disable uPNP didn't help either (they have been suggested in similar topics).

  However, the IP displayed tab troubleshooting/Diagnostics reflect my external IP address (the IP displayed by http://whatismyip.com), which is weird, because I never have IP from my ISP from 100, that is displayed on the Diagnostics tab. So I guess it's a fake display or it relates to access to my router via www.linksyssamrtwifi.com ?

  Anyway I tried the two IPs from the outside, but the transfer simply doesn't work. (It works fine when I use my old router TP-Link).

  Please advise!

  Sorry guys, it seems indeed a double NAT problem. My ISP can detected MAC address change when I started using EA6900 (thinking that I couldn't not need public IP?) and since then he sends me IPs for NAT - ed. It is strange that the same day, he was working with my old router, but now it is even not working with my old router and not even working when I connect directly to my windows PC to my ISP (via PPPoE). I called their support line and they said that they will solve this problem within 72 hours. In any case, thanks for your help!

• The port forward does not work in RV120W?

  I am trying to configure a simple port forward in the RV 120W router, but can't seem to make it work.

  I created a custom service called RDP for the TCP 3389 3389 port.  I added a Port forward to always allow the RDP service, from any source to destination IP 192.168.50.23 IP address.  I tried with 'identical to incoming port' and also specified the port 3389 to forward to and to.

  Firewall access rule is activated and incoming value, always allow, RDP service, any source & destination IP, DNAT IP is 192.168.50.23.

  RDP works at the IP address of the local network.

  Any ideas?

  There is a problem with the RV220W, and work around this problem:

  Just use the firewall rules and not port forwarding.

  try on your rv120w and see.  Make sure that the last thing you do is re save firewall rule.

  It will be useful.

• LRT214 Port Forwarding does not

  First of all, when you create a service in the port forwarding section, why to select the two TCP/UDP has been omitted from the selection must be embarrassing for Linksys.  Creation of 2 services, one for the other for UDP and TCP are bad design.  Would love to see that this problem has been corrected in future updates of the firmware.

  The main problem is I have configured port forwarding services, but I can't get anything to work.  I am able to access remotely to the router using the port 1443 that is configured in a separate section.  I worked in the network design and mgmt for 10 years and why Linksys decided to make the management for the LRT214 so different interface, then the rest of the market was a bad decision.  Is there anything else you can suggest to help out why these ports cannot be opened through the FW?

  On this router logs show nothing.  There is no log for blocked inbound connections and there is a class router business?

  After setting up some boxes of Windows on the local network, then transfer to a custom RDP listening port, I am able to RDP in these Windows boxes remotely.  It verifies that the Linksys router is forwarding ports correctly.  The question then is something on the Synology device itself.  Thanks for your response!

• WRT160N V3 DMZ and Port-Forwarding does not work

  Hi all

  I have a V3 WRT160N and DMZ or Portforwarding do not work.

  I tried on locally

  WAN_PC-> WAN - PORT-> WRT160N V3-> LOCAL - PORT-> LOCAL_PC

  The WAN_PC has a static IP 192.168.1.2, subnet 255.255.255.0

  The WAN PORT has a static IP 192.168.1.1, subnet 255.255.255.0

  ON the WRT160N V3, I set up a DMZ on 192.168.0.100.and off the firewall.

  On the LOCAL_PC (192.168.0.100:8888) is an Apache

  So when I type 192.168.1.1:8888 on the WAN_PC I get NOOO the Apache on 192.168.0.100:8888 Web site?

  WHY??????????????

  Please correct me if I'm wrong. My understanding of your installation, it is that you have a computer connected to the internet port of the router and another computer connected to the router's ethernet port? Is this correct? You don't have a modem for internet connection or something like that? If you can post here a diagram that will be better. Thank you.

• Adobie flash player not working not - help!

  When you play it is slow and freezes for a few seconds, this is a slower operation. Games does not work correctly.

  When you play it is slow and freezes for a few seconds, this is a slower operation. Games does not work correctly.

  Uninstall the flash player and install a more recent version of flash player. (10.3)

• BlackBerry Smartphones Internet services bizzarely works not - help!

  Hello

  I have a Bold 9700 and basically whenever I am out of my home wireless network, my internet on my BB has stopped working. This was never a problem before, but now when I'm away from my browser, bbm and emails all stop working (although kik doesn't, oddly). I am pretty sure that this is not a problem with the signal, here where I am at the moment to adequate coverage and this has happened almost anywhere, I took it too. Not quite sure what went wrong and how there to remedy, but would like to have guidance that can be offered. See you soon!

  Yes, the BlackBerry logo

  On your home screen indicates you are connected to the required data BlackBerry for e-mail and other services other data functions BlackBerry like BBM and Facebook app, etc..

  I don't know why it's disconnected except maybe in some areas of low signal or data not?

• "physical, no written control point" is low, but increase in roll forward does not help.

  We have a busy database, the physical write is so high that we want to reduce the physical writing. The statspack, we could see "physical writes non checkpoint" is low in comparison with 'physical writing', so I think the physical write results from control point is high, then I increased the size of Redo from 2 G to 4 G (now the command to log every 4 minutes). I hope that this may reduce the physical writing, but the fact is that the roll increased forward is powerless.

  Statistic                                      Total     per Second    per Trans
  --------------------------------- ------------------ -------------- ------------
  physical writes                            8,298,681        9,210.5        249.8
  physical writes non checkpoint             3,229,321        3,584.2         97.2

  We use the oracle 10.2.0.3 on solaris 10, checkpoint-related parameters are

  fast_start_io_target                          0                  
  fast_start_mttr_target                        0                  
  log_checkpoint_interval                       5000000            
  log_checkpoint_timeout                        0     

  Thank you
  
  Published by: user646745 on August 18, 2009 01:24

  FAST_START_MTTR_TARGET is set to 0

  Make sure that you explicitly defined FAST_START_MTTR_TARGET on 0.
  If you have not set it, a "show"parameter will be enabled see the value 0, but the automatic setting of the control point will be . (See Note MetaLink #265831.1)

  If the size of redo is 4G, we will have two control points for each 4G...

  Yes, there will be one for the log_checkpoint_interval and the other for the control of log file.

• Pavilion p7 - 1380t: USB ports not working not

  The two front USB ports do work not today. Worked fine yesterday. Everything I plug is not coming. Using ports in the back, they work very well.

  Someone at - it ideas about the problem and a fix?

  Thank you

  Hello @xploded16,

  Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the Forums of HP, I would like to draw your attention to the Guide of the Forums HP first time here? Learn how to publish and more.

  I read your post on how the front USB ports on your desktop computer do not work, and I'd be happy to help you in this case!

  To enable your system to recognize the USB ports before once again, I recommend that you follow the steps described in this document on Troubleshooting connections USB (Windows 7).

  Please re-post with the results of your troubleshooting, and I look forward to your response!
  
  Concerning

• RV130W - Firewall locks? Port forwarding no longer works!

  Hey all,.

  I have a Cisco RV130W router, which seems to have problems with the Port Forwarding type stuff.  Port forwarding is without a doubt done properly (as I did on all other RV130W) and the ports actually work for a few hours or maybe more, but then it's like she goes down on the lock and blocks all traffic that passes through.

  My solution is to reboot the router for port forwarding works again.

  I can't access management "distance" more when this happens.  I can access the Web Interface via LAN and Internet and network continues to operate correctly - DHCP and all.

  I'm under the new firmware.

  Any ideas?  Thank you!

  Hello Jeff,.

  Sorry the camera does not work as expected.  I have seen this problem before and I think that you would see if you were doing a capture of packets across the Wan is the router receives a SYN, but never respond with a SYN ACK.  We have found a workaround is to, I suspect that you have single port forwarding enabled, try to configure the same ports in the range of port forwarding page.  Configure the ports of departure and end in the same port number, and remove the single port forwarding configuration.  I hope this helps.

• Error port forwarding

  Help, please...

  My port forwarding work orders at random (not quite sure when).

  I have an EA4500, software smart wifi linksys, when I click on the Security tab, I get the following error:

  ------------------------------------------------------------------------------------------------------------------------------------------------------------------

  Unexpected error 2118

  We encountered an unexpected error. If the problem persists, please visit our Technical Support site.

  When you re-flashed and reset the default router, have you used the backup config the router settings? If so, I suggest do you another factory reset and manually input parameters and avoid using the backup file.

• Port Forwarding problem through 2 routers RVS4000 2 subnets

  I modified a building network to be compliant (Visa) PABP where two router and two subnets are required.

  My original CD building network configuration was designed to allow remote access to a server terminal server via the port forwarding on a RVS4000 router. So cables / modems-> xx.xx.xx.xx wan ROUTER lan 192.168.1.1--> subnet 192.168.1.0 with TCP 3389 Port forwarding for 192.168.1.11 (terminal server).

  The new configuration of the network is composed of two routers RVS4000 on two subnets. So the Modem cable-> wan xx.xx.xx.xx ROUTER1 lan 192.168.2.2-> Subnet 192.168.2.0-> DMZ 192.168.2.14 and the second router wan ROUTER2 lan--> subnet 192.168.1.0 192.168.1.1 192.168.2.1.

  ROUTER1 is configured in Bridge mode and ROUTER2 is configured in router mode. Port forwarding on ROUTER1 to port TCP 3389 is 192.168.2.1 (on ROUTER2 wan port). Port forwarding on Router 2 for the TCP 3389 must 192.168.1.11 port (server address terminal server).

  With this new configuration of network I am able to connect to the Terminal Server remotely. No problem with access to the Internet and the 192.168.2.0 subnet from inside the 192.168.1.0 subnet.

  So I think my problem is through two RVS4000 routers port forwarding. Any help on this problem will be appreciated.

  Thank you.

  1. can you access the terminal server server from inside the subnet 192.168.2.0/24 using the IP WAN to Router 2, which is access 192.168.2.1:3389 from inside 192.168.2.0/24.

  2. turn on Router 2 router in Bridge mode. Try again. My guess is that this will make the work of transfer. I think that port forwarding is linked to the NAT/gateway mode. No NAT no transfer. Is not logical to use the transfer when you are able to access the IP directly without NAT. Of course, the web interface does not allow you to forward a port located outside the LAN subnet...

  3. are you sure that you can access internet through Router 2 in router mode on the LAN subnet router 2? Usually in the NAT their own LAN subnet routers only bridge mode but not others. If the RVS4000 not NAT a different subnet that would be good to know.

• RV220w port forwarding notworking

  I want to transfer some port in the 8000-8100 Series.

  Goal is to reach the web interfaces for secondary roads real HTTPS protocol.

  Port forwarding does not work.

  An experienced person / solution for this. I really can use some help.

  see below for the current settings,

  For exaple 1 router IP wan = 192.168.0.17 Protocol Https port 8007 open external.

  It is a static IP address configured in the RV220W

  RV220 settings

  Configuration automaitc WAN IP-> external DHCP 192.168.0.100

  Network LAN IP 191.168.0.1

  subpattern 255.255.255.0

  Mode DHCP: DHCP server.

  Start 191.168.0.2

  end 191.168.0.10

  static addresses

  191.168.0.15 port forward 8005

  191.168.0.17 port 8007 forward.

  Firewall settings

  Type of incoming connection

  action always allow

  Https service

  IP source everything

  Send to the local server ip 191.168.0.17 Dnat

  status of enabled rule

  Port forwarding

  Action always allow

  Https service

  IP source everything

  destination 191.168.0.17

  internalPort 8007

  Access distance real webbrowser: Https://192.168.0.100:8007

  Hello, John...

  You must create a custom service and add the service to the access rule.

  To create the service customer please visit: http://sbkb.cisco.com/CiscoSB/ukp.aspx?vw=1&docid=ffc3bc90423f4848abf81360523471f6_Custom_Service_Configuration_on_RV120_W_Firewall.xml&pid=4&fcid=&fpid=&slnid=5

  Access rule: see: http://sbkb.cisco.com/CiscoSB/ukp.aspx?vw=1&docid=01ef2188693e42058388dbfe3311ea1f_Access_Rules_Configuration_on_Cisco_Small_Business_RV120W_Wi.xml&pid=4&fcid=&fpid=&slnid=5

  Kind regards

  Siva

• Why isn't my port forwarding of the opening port

  I have the latest version of the 3 terabyte time capsule. I'm trying to forward a port so I can access my security cameras and it does not open.  My camera 100 port needs to be open and it will report as not open on any port test sites. Any ideas as to why, I use a static ip address of the server for the security system.

  Testing websites are useless... test by plugging actually to the camera from a device attached to a captive phone or a friend...

  Port forwarding works only if you have the public IP address on the Wan of the TC... and it's the only router in the network... is this the case?

• Port forwarding on Linksys WRT54G

  Hey I have problems with Port Forwarding on my Linksys WRT54G. The port, I need open is 28960. I followed guides and thought I did everything correctly, but his does not work. Here's what I've done so far:

  -J' put a static IP address and took a screenshot of my settings here:
  

  -Here is my page of port forwarding:
  

  -Under the ' security > firewall "tab I unchecked"Block anonymous Internet Requests ".
  -In addition, I tried to adjust the 'DHCP server' for people with reduced mobility
  

  Is there something that I don't forget or do wrong?

  Evreything is fine... Make sure that the DHCP server is activated (do not disable it)...

  The only reason why port forwarding does not work because this port can still report it as "Blocked", this only happens if you have an old firmware on your Linksys router...

  Update the firmware on your router, reset and re - configure from scratch and do port forwarding, see if it works...

  Download the Firmware from here

  Follow these steps to upgrade the firmware of the device: -.
  Open a page in Internet Explorer browser on a computer hard wired to the router...
  In the address bar type - 192.168.1.1... Leave name empty username & password admin lowercase usage...
  Click the 'Administration' tab - then click on the 'Upgrade Firmware' under the tab-here, click on 'Browse' and navigate the .bin firmware file and click on "Upgrade"...
  Wait a few seconds until it shows that "the update is successful," after the upgrade of the firmware, click on "Reboot" and you will be returned to the same page OR it will say 'cannot display the Page.

  Now reset your router:
  Press and hold the button of reset for 30 seconds... Release the reset button... Unplug the power cable from your router, wait 30 seconds and reconnect the power cable... Now re - configure your router...