LRT214 Port Forwarding does not

Similar Questions

• Port forwarding does not work on EA6900

  Please help me to know what is the reason for this port forwarding does not work on my Linksys router:

  Model: EA6900 v1.1
  Firmware version: 1.1.42.161129

  I've set up two ports: TCP 22 and 8070 TCP to 192.168.1.10. (192.168.1.10 is up and running, I can reach the LAN ports).

  Yesterday, I had a live chat with Linksys support we tried to re - download the firmware even, but that did not help. Then factory reset and reconfigure the router did not help either.

  Unchecking "Filter anonymous Internet requests" and disable uPNP didn't help either (they have been suggested in similar topics).

  However, the IP displayed tab troubleshooting/Diagnostics reflect my external IP address (the IP displayed by http://whatismyip.com), which is weird, because I never have IP from my ISP from 100, that is displayed on the Diagnostics tab. So I guess it's a fake display or it relates to access to my router via www.linksyssamrtwifi.com ?

  Anyway I tried the two IPs from the outside, but the transfer simply doesn't work. (It works fine when I use my old router TP-Link).

  Please advise!

  Sorry guys, it seems indeed a double NAT problem. My ISP can detected MAC address change when I started using EA6900 (thinking that I couldn't not need public IP?) and since then he sends me IPs for NAT - ed. It is strange that the same day, he was working with my old router, but now it is even not working with my old router and not even working when I connect directly to my windows PC to my ISP (via PPPoE). I called their support line and they said that they will solve this problem within 72 hours. In any case, thanks for your help!

• The port forward does not work in RV120W?

  I am trying to configure a simple port forward in the RV 120W router, but can't seem to make it work.

  I created a custom service called RDP for the TCP 3389 3389 port.  I added a Port forward to always allow the RDP service, from any source to destination IP 192.168.50.23 IP address.  I tried with 'identical to incoming port' and also specified the port 3389 to forward to and to.

  Firewall access rule is activated and incoming value, always allow, RDP service, any source & destination IP, DNAT IP is 192.168.50.23.

  RDP works at the IP address of the local network.

  Any ideas?

  There is a problem with the RV220W, and work around this problem:

  Just use the firewall rules and not port forwarding.

  try on your rv120w and see.  Make sure that the last thing you do is re save firewall rule.

  It will be useful.

• WRT160N V3 DMZ and Port-Forwarding does not work

  Hi all

  I have a V3 WRT160N and DMZ or Portforwarding do not work.

  I tried on locally

  WAN_PC-> WAN - PORT-> WRT160N V3-> LOCAL - PORT-> LOCAL_PC

  The WAN_PC has a static IP 192.168.1.2, subnet 255.255.255.0

  The WAN PORT has a static IP 192.168.1.1, subnet 255.255.255.0

  ON the WRT160N V3, I set up a DMZ on 192.168.0.100.and off the firewall.

  On the LOCAL_PC (192.168.0.100:8888) is an Apache

  So when I type 192.168.1.1:8888 on the WAN_PC I get NOOO the Apache on 192.168.0.100:8888 Web site?

  WHY??????????????

  Please correct me if I'm wrong. My understanding of your installation, it is that you have a computer connected to the internet port of the router and another computer connected to the router's ethernet port? Is this correct? You don't have a modem for internet connection or something like that? If you can post here a diagram that will be better. Thank you.

• Call forwarding does not work ;-((

  Hello

  I got Skypenumbers from the beginning. But since two months call forwarding no longer works. I renewed my subscription; I have 30 euros on credit account. I even tried a new Skype number to see if the old number could have crashed. But also the new number does not work with call forwarding.

  It's abit frustrating to read Skype/Microsoft does not very serious service.

  This problem will be resolved, or must we begin to use the other services?

  AB

  Dear Elaine,

  I have finanlly managed to get a conversation with the assistance service. It was still not available, but I got lucky.

  And they found the problem; I got in the App on one of my Macs 'private' privacy setting This is why di call forwarding does not work. So I changed it to open and now it works.

  Thanks for your help and advice; I am happy that this solved in the end.

  See you soon

  AB

• mail forward does not

  Since the last update to the OS my mail forward does not work. Help please!

  Do you mean that you cannot select the message? or do you mean that you select to forward the message and the recipient never receives the message?

  You use Mail?

• FC Port-Channel does not

  Hello

  I need help, I'm setup CF port-channel between 9148 MDS and Cisco fabric Interconnect 6248 and the port-channel does not work. He said no operational members.

  For the MDS, see configuration below:

  NPIV #feature SW (config)

  SW (config) #feature fport-channel-trunk

  SW (config) #interface fc1/17-18

  SW(config-f) force Group-channel mode # 63

  SW(Config-if) F #switchport mode

  SW(Config-if) #switchport trunk-allowed vsan 1-2 (I have only vsan 1 and 2)

  SW (config) #no close

  SW (config) #interface 63 port channel

  SW(Config-if) F #switchport mode

  SW(config-f) #switchport trunk-allowed vsan 1-2

  SW (config) - #no close

  Note: the ports are assigned to vsan 2

  See the attached screenshots for interconnection fabric config

  On the fabric of interconnections switchport mode are defined E. What I have to change to F. If yes where can I change since the option is not there in the UCS Manager?

  have you added the VSANS on the UCSM as well?

  What Code are you runnig on the San Norhbound selector?

  You can be hitting

  https://Tools.Cisco.com/bugsearch/bug/ CSCty04686

• Port 139 does not not on Windows 7 after deployment.

  Hello

  I created some images of new installations of Windows 7. But the pack of GPO that is applied in MDT 2012 changes settings in windows 7 so that port 139 does not correctly work with gap analysis network SMB.
  recently we bought workstations that already have a Windows 7 image on them. But because computers OS was deployed hollow some imaging modalities 139 port does not work properly. Is there such a tool from Microsoft to restore the port 139 on a charge CD Windows 7 feature?
  Or any Microsoft employee who has done any research into this problem and tested and found a solution to this problem?
  Thank you.

  You can take this on the Technet forums because I don't know where the sizes are fixed. One thing to remember when the GPO is that in many cases, changes may "tattoo" the registry and must be explicitly changed back instead of be reset to the default value.

  http://social.technet.Microsoft.com/forums/en-us/category/w7itpro

  I hope this helps.

• When I plug my portable hard drive to the usb port it does not read and display the contents...

  When I plug my portable hard drive to the usb port it does not read and display the contents...

  Hi deaza,.

  Ø Have you connected the USB hard drive to the computer directly or you have used an external USB hub to connect?

  O trying to connect to another USB port to check if it works?

  O the hardrive shows in windows of the computer when you connect it?

  Method 1:
  If you have installed security software, I suggest you to temporarily disable the security software and connect the USB and check to see if the same problem happens. Make sure that you enable the security software after checking.

  Alternatively, you can try to plug the USB key into a different USB port and check if it helps.

  Method 2:
  I suggest trying to launch hardware and troubleshooting of devices and check to see if it helps, here is the link:http://windows.microsoft.com/en-US/windows7/What-to-do-when-a-device-isn ' t-installed-correctly

  Method 3:
  If this does not help, then follow these steps:

  (a) remove all your USB devices. Use the safely remove the feature to turn them off.

  (b) open Device Manager and navigate to the section for USB. Uninstall all USB drives. There should be one for each USB port, and then restart.

  To open Device Manager, go to the link below and follow the steps:

  http://Windows.Microsoft.com/en-us/Windows7/open-Device-Manager

  (c) Windows should re - find all of the devices. If it is not the case, note the error message and let us know.

  You can also navigate to the link below and follow the steps to install the USB device.

  http://Windows.Microsoft.com/en-us/Windows7/install-a-USB-device

  I hope this helps. Let us know the results.

  Thank you and best regards,

  Srinivas R

  Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Standard vSwitch_Custom VM (Vlan200_VM network) port group does not.

  Hi guys...

  Scnerio:

  ESXi 5.0

  VCenter 5.0

  2 connected local network cards to vswitich 0 Active\Active configuration.

  The virtual computer name: FSAPP_1

  Note: good VLANS are created externally NETWORK

  I created another group of ports VM network VLAN 200_VMnetwork.

  I have attached TWO maps LAN to VM. A LAN card is connected to the port default VM network group and another is connected to network VLAN200_VM.

  A LAN card is connected to the local network (Private IP) and another is connected to the Wan (public IP)... IF I CONNECT the TWO VMNIC "DEFAULT virtual machine network" I am able to ping both subnets.

  
  

  But any vNIC which is connected to the VLAN200_VM network is NOT working...

  
  

  
  

  Please see the attached snapsshots...

  Thank you

  I did not ask you to do what I asked you to test is the separate two VM on the host even be configured to use the VLAN 200 portgroup and verify that these two people are able to talk to each other.

  Once you've found that the books above. Go back to your network team and make the request to configure the switch in the trunk output ports (which does not remove the tag VLAN on the package on the output of the switch) as opposed to be defined as access (that strips the tag VLAN).

  It is my firm belief that the port group does not work because your switch is misconfigured based on my above statement.

• New for iPhone charging Port 6 does not

  Recently, I had the charging port on my iPhone replaced 6, because the original had stopped working properly. With the original, I had to shake the charger autour so he could load, but it was so bad that I could only load if I it held in place. I went to a store local tech to g

  With the new port, I am able to load it with a standard charger Apple iPhone or iPad. However, it does not charge to something else - in the car, with a cell phone charger, when it is connected to my Mac - nothing. When it is connected to these other devices, the phone doesn't even it is plugged.

  Thoughts?

  Means, "went to a store local tech to fix.

  Looking for advice!

• Pavilion 23-b320: Port SD does not

  When I insert one of my SD cards in the SD port, the computer does not meet the presence of the SD card.  When I open file Explorer, the SD card does not appear.

  All USB ports work.

  How to solve this problem.

  Note: this computer is my wife, and he sat on his desk for 2 years unused.  We got married recently and am now trying to get to the top and running.  I have done all the necessary updates for all programs.

  I don't have a recovery disk.

  Interesting...

  See if this driver works instead.

  The W8 driver for your model page shows it has a Realtek card reader.

  http://h20564.www2.HP.com/hpsc/SWD/public/detail?swItemId=ob_155234_1

• Port forwarding works not, help

  I have a string of teracom TCW120B controller and I want to remote control. Those of teracom gave me the following response to configure the router:

  "Is there a router between the controller and the device? If there is a router, it should do the port forwarding.
  http://212.25.45.120:81 /.
  http://212.25.45.120:82 /.

  These two devices are in our office. I have forwarded port 81 of our router (with the real IP 212.25.45.120) to port 80 (http protocol) to the ip address of the first unit.
  The 82 port is forwarded to port 80 on the ip address of the second device. »

  I can not I put the lan router you can order Remote control TCW120B.
  Please help me with this problem.

  Ignore the Wi - Fi Protected Setup button if your wireless network is already reached.

• N2048 port security does not

  Hi Experts,

  Only, we have deployed a new site that uses the Dell N2048 switches in a stack.

  Now we would add port security to the switch, Port-MAC locking to lockdown one port if another computer.

  According to the manual, to put in place we only need of to the port to locked under the MISTLETOE under switching, network security, port security.

  This does not activate it.

  We tried to add via the command line, in the ports of test, it now shows:

  switchport security of dynamic ports 1

  Still, port security is not enabled. There is another thing that must be enabled in the world to do this job or other commands?

  Thank you

  The output of port security-# show is as follows:

  Port Security Administration Mode: enabled

  It is possible that the tests were not done fast enough. I spent the time-out and ask them to test again.

  Thank you

• PowerConnect 2824 Ports SFP does not

  We bought a new switch 2824 with a corresponding to SFP module replace old 2724 PowerConnect and SFP module.

  After the configuration of the switch and installing it, we were able to get a connection on our uplinked to fiber.
  SFP light illuminates and flashes from time to time, and the switch detects correctly module SFP is inserted and that the fiber is connected.  We can see the insertion of the SFP is detected and the switch for change of fiber mode by looking at the output of the console, and the web administration port status page lists the port as "ComboF" when the SFP is inserted and the fiber is connected.

  However, the switch always indicates that the port State is down.  (The port is not administratively disabled.)

  The old switch works very well with the old SFP module.  The new switch does not work with the old or the new module SFP.  We tried two combo SFP ports.  We also checked that the fiber itself is fine. We cannot get the new switch to display the drop-down list port status that up when you use the SFP. We tried to completely reset the new switch by removing the configuration file via the boot over the serial connection menu and re-run the initial configuration wizard, but the port still won't go up.

  Any ideas?

  After a few tests yesterday, we determined that part of auto-negotiation must be disabled for switch work with our copper and fiber Media converters.

  The 2724 works very well with our media converters, with auto-negotiation enabled.

  The 2824 works very well with auto-negotiation enabled when it is connected to an another SFP transceiver in building switch.

  But when we introduce the Media Converter in the path, the 2824 will bring only the link up if you disable auto-negotiation.

  So far, everything looks good.