Portege R500 upgrade to Win 7 64 bit: lost and no scrolling touchpad driver

Similar Questions

• Portege R700 - how update Win 7 32 bit to 64 bit?

  After having upgraded the RAM 8 GB, how now move the installed "Windows 7 Pro" from 32-bit to 64-bit in order to make the best use of the extra memory?

  No "Tecchie", so please explain in simple terms!

  Thank you

  Hello

  You can not move from Win 7 32 bit to 64 bit.
  To use the Win 7 64-bit system, you must make a full, clean install of Win 7 64 bit.

  This would require the installation of all your software, tool, utility as pilots.

• How to upgrade to win 7 64 bit

  I just installed win 7 32 bit, but now I found that I have to install win 7 64 bit. How can I upgrade?

  In addition, my laptop's Mac Pro 13 inch Mid 2012.

  I suggest to remove the 32-bit and 64-bit. There is no upgrade path supported on a Mac.

  To use 10 Windows on your Mac with Boot Camp - Apple Support (and this is true for all versions of Windows on Mac),

  Update for 32-bit versions of Windows

  If you have an existing installation of 32-bit Windows on your Mac, you will need to backup your important files so that you can remove the existing Windows partition and install a 64-bit version of Windows.

  1. Back up all the important files on your Windows partition.
  2. Use the Boot Camp Assistant to remove the existing Windows partition.
  3. Then, use the Boot Camp Assistant to install a 64 bit version of Windows on your Mac 10.
  4. Once you have completed the installation of Windows, copy your important files on your Windows drive.

• Upgrade to Win 7 32 bit to Win 7 64 bit

  A few years back, I bought a Win 7 upgrade pack who had licenses for three computers.  The upgrades were available as 32-bit or 64-bit.  I have now updated three of my XP computers and make them all running and enabled.  Unfortunately, by mistake I made one a 32-bit improvements.  I would like to correct this and reinstall as a 64-bit (as I contemplate the possibility of a Win 10 update).

  My concern is try a new installation of 64-bit on 32-bit installation will result in denial of activation as this can be considered a fourth facility of a three license upgrade pack.  Can someone clarify this before I attempt an upgrade?

  Thank you

  You're still allowed to clean reinstall Windows 7 as often as you want and always re-enable generally without special measures because the material is already associated with this product key, but even if not you can migrate to Windows 7 at retail to any other PC whenever you want as long as it's only on (in the case of Family Pack) 3 PCs at a time.

  If you have problems with Activation, open a command prompt, type slui 4, then press ENTER, follow the prompts to re-activate that refreshes the the hardware ID in the Activation of MS. servers  If it detects possible installation of additional hardware device it will ask the key question "PC how much this copy is installed on?" to which in your case, you can answer only up to 3.  This gives permission to MS to disable it on any PC excesses that do not already have their signature of material recorded for this product key in their servers.

  If for some reason, this fails, stay on the line for the activating agent and explain your situation.  Normally this solve the problems, but if not Service the customer is responsible to ensure that a valid key gets all its due installs and will open a case of support to ensure that this happens.  If this is not the case, let us know here.

• T61 upgraded to win 7 32 bit Readydrive can not be activated

  I have a T61 8889 AD3, updated operating system at level 32-bit form to Win 7 32 bit vista. The foucation readydrive of Intel turbo Memory can not be enabled after the upgrade. Turbo Memory report below:

  Installed Kit: 8.9.2.1002
  Shell Version: 8.9.2.1002

  Name of the operating system: Microsoft Windows 7 Ultimate
  OS version: 6.1.7600 Build 7600
  System name: MY - PC
  Manufacturer: LENOVO
  System model: 8889AD3
  Processor: Intel (r) Core (TM) 2 Duo CPU T7700 @ 2.40 GHz
  The version of the BIOS/Date: LENOVO 7LETC6WW (2.26), 11/05/2009

  Language: ENU

  Intel Turbo Memory

  Disk cache location:-1
  Model name: no
  Capacity: 0 GB

  Installation status: present
  File: C:\Windows\system32\drivers\iaNvStor.sys
  Version: 1.10.1.1002
  Provider of: Intel Corporation

  OROM Version: 1.10.1.1002
  OROM status: success

  It seems that the readydrive highlights disk, cache because a disc hidden (in anonymous form, GB 6,17) ahead of C: drive.

  I try to use the drivers for Vista, but the installation process is always altered; When I put my T61 hibernation, there is no file option of hibernation in cleaning disc as it used to be.

  Does anyone have ideas for this?

  Good news, my turbo memory works fine now. I reinstalled the system, but the same symptom persists, but I have to solve

  System

  Installed Kit: 8.9.2.1002
  Shell Version: 8.9.2.1002

  Name of the operating system: Microsoft Windows 7 Ultimate
  OS version: 6.1.7600 Build 7600
  System name: MY - PC
  Manufacturer: LENOVO
  System model: 8889AD3
  Processor: Intel (r) Core (TM) 2 Duo CPU T7700 @ 2.40 GHz
  The version of the BIOS/Date: LENOVO 7LETC6WW (2.26), 11/05/2009

  Language: ENU

  Intel Turbo Memory

  Location on the disk cache: 0
  Model name: HITACHI HTS541616J
  Capacity: 149 GB

  Installation status: present
  File: C:\Windows\system32\drivers\iaNvStor.sys
  Version: 1.10.0.1012
  Provider of: Intel Corporation

  OROM Version: 1.10.0.1012
  OROM status: success

  You need to know:

  First of all, some people say that allowing to Hibernate will be active readydrive feature, but it doesn't seem to work on my T61 with win7. Several times in retirement, it did not help. Despite readydrive works great now, I do not see files of Hibernation in 'Disk cleanup', unlike the situation in the Vista system.

  Second, please check:-> disk drivers Device Manager click on the properties of the drive, and then click strategies, you should see the two options in writing-coching lives checked; You can also see NV Cache option on the right of the policies.

  Finally, once readydrive works well, you should see ' Windows ReadyDrive disk Power Savings Mode activated' under the option of hard drive of the advanced settings in Power Options.

  Following steps may help:

  Option 1:

  Download 1.10.0.1012 - 8.9.2.1002 of

  http://www-307.IBM.com/PC/support/site.WSS/document.do?lndocid=MIGR-67820

  at your desk, then unzip it (do not install). Then find the setup.exe of: C:\DRIVERS\WIN\Turbomem

  Click on-> run as administrator. Once the driver is installed, do not restart, and then click Intel Turbo Memory Console, then check both options. Restart

  If option 1 does not help, try it please:

  Option 2:

  Download the IBM link above 1.5.0.1013 - 7.8.0.1012 on you desktop.

  then unzip it (do not install), then find the setup.exe of: C:\DRIVERS\VISTA\Turbomem

  Make a right click-> compatibility-> check run this program in compatibility mode for: Windows Vista

  Once the driver is installed, do not restart, and then click Intel Turbo Memory Console, then check both options. Restart

  This driver does not work with win7 system, then you can follow option 1.

  I'm not a technician and instructions above appear simple and reckless, but at least my T61 readydrive feature works correctly now.

  Good luck to you ~!

• Win8 32-bit upgrade for win 8 64 bit

  I bought Win 8 32 bit via download using the wizard.  It's the right version for my computer and I don't have the disc.  Now, a few months later, my PC has melted and I am building a new machine 64-bit from scratch.  I was able to save the hard drive.  How to convert or move to Win 8 64 bit?  Do I have to buy the whole OS again, buy the correct CD and do a clean install, pay and repeat the download?

  Thank you.

  https://techingiteasy.WordPress.com/2013/02/14/how-to-migrate-from-32-bit-versions-of-Windows-to-Windows-8-64-bit/

• Portege R500-11Z: how to use the external mic and hear the internal speakers

  We have a Portege R500-11Z running XP and want to use Skype with an external table microphone and the internal speakers.

  When connect us the microphone to the Jack MIC the Portege, built-in speakers cut out!

  How to use an external mic and still hear the internal speakers?

  Hello

  > When connect us the microphone on the Portege, built-in speaker MIC Jack cut!
  Are you sure you used the microphone port and no headphone port?

  Have you checked your settings Audio from Skype?
  There is an option called ring through the speaker too or something like that.

  Please also check the Realtek HD audio Manager in Control Panel.
  There is a tab called Audio i/o.

  Usually, you can change the connector settings, by clicking on the small key-tool icon.
  Disable the option called Mute rear output when plugged headphones before

  As you can see is called headset and not so I m confused a little bit why the speakers are turned off when you connect an external microphone.

  By the way; There is also a tab called micro.
  Check if the two options that reduce the echo and noise are OFF

• updating Win 7 32 bit to Win 7 64 bit with output formatting of HARD drive?

  For some reason any my Panasonic Toughbook came with Win 7 Pro 32-bit. The material is prepared according to manufacturer 64-bit. Who could ever think about buying the PC like this (quad CPU, 8 GB of RAM etc) is preloaded with 32-bit? In any case, I talked to people from panasonic, they say, it is not necessary to wipe the HARD drive to upgrade to 64 - bit. and sent the links to the drivers to install and procedures how to. The qUESTIONs ARE! Is it still possible? All programs and apps will work after installation? I'll be able to access the windows after upgrade. If I do a backup of files and settings in 32 bits can restore 64-bit so only the lost data? If not successful can I use same license key 32-bit here to install Win 7 Pro 64 bit. Has it been done before?

  Thank you for all the input

  As the computer was supposed to be provided with 32-bit Windows and 8 GB of RAM their technical knowledge should be considered as somewhat suspect. 32-bit Windows can access up to 3.2 GB (approx.) of RAM, it should be 4 GB, but for technical reasons, it can not, 8 GB would be useless.

  According to the original age of the computer, it only used to be quite true 64 bit software so if a computer has 4 GB of RAM or less, there was little interest in installing Windows x 64. Windows 7 x 64 increases the required minimum memory of 1 GB 2 GB same 4 GB of RAM is questionable, to get an advantage, that it should be more.

  I suspect the specifications of basic material for the system was such that the image of the master has x 32 and nobody at Panasonic said that if they offered an option for 8 GB they needed to provide a revised image.

  Normally OEM software provided as 32-bit or 64-bit, you don't get together in the peloton to the difference in detail so there may be a limitation as to what technique you can install. Then of course there is the problem of knowing where you are going to get the operating system. If the recovery of Panasonic's 32-bit all you have. Unless Panasonic brings that put you with a recovery disc 64-bit, you will need to provide your own license. You obviously have a case if they provided the spec of 8 GB to request a package of them FOC, but I doubt if they will respect.

• Problem with Win 7 64 bit OS and itunes with the corefoundation.dll?

  I am running Win 7 64 bit OS. When you try to run iTunes I get error message: the program cannot start because corefoundation.dll is missing. Try to reinstall to see if that solves this problem.
  is there a problem with itunes and Win 7 64 bit? or by reinstalling the dll file fix?

  Uninstall and reinstall hopefully should solve your problem.

  MobileMe: "CoreFoundation.dll was not found" or "Apple Application Support is missing" alert
  http://support.Apple.com/kb/TS2211

  How to fix Corefoundation.dll errors
  http://www.dll-error-fixes.com/resolve-corefoundationdll-missing-errors/

  Have you tried right-clicking on the program.exe Setup and selecting "Run As Administrator" option?

  Have you tried to clean your Temp folder, you can do this by typing folder in the Start Menu RUN box.  This will open your Temp folder, there, you can remove all Windows will allow you to do.

• Portege R500 - Upgrade processor and RAM

  Can I put in my proceror R500 and RAM?
  Is possible? If Yes, how can you procesor I used?

  Robert

  Hello

  You can upgrade the RAM.
  You can use the DDR2 667 MHz (PC2-5300) or 533 MHz 200 - PIN SODIMM modules.
  You can use a 1 GB RAM module this is the max!
  There is also an internal RAM which can be removed if only one slot is expandable!

  With regard to upgrading the CPU.
  Usually it s not advised to replace/upgrade of the processor because the BIOS has not been tested with other processors

• Portege R500 - problem of Windows 7 32 bit HSDPA.

  Hello

  I installed Win7-32 (own) today, but I can't seem to install the vista driver and software correctly. I installed most Toshiba drivers for my system, including the power of 3 G (vista) and value added package. The modem is on according to VAP.
  Error message: "the wizard was interrupted before drivers Mobile Wireless Broadband could be completely installed." Your system has not changed. To complete installation at another time, please run Setup again. »

  Mnemonic

  Thanks for sharing this with us!

• Computer HP laptop slim 500 GB HARD drive: used for HP laptop HARD drive upgraded to Win 10 Pro with key now stuck after HP Drive Encryption Login

  I bought a portable hard drive used HP for the upgrade of my Lenovo G550 with ugraded CPU with Intel's CORE DUO T9300 2.50 ghz

  (HP hard drive: computer laptop slim drive HARD 500 GB SERIAL ATA DISK DRIVE S/N W627S9NL P/N 756731-001 MFG Seagate Technologies DOM 8 / 2015)

  I was happy to see that the hatd drive had already installed because Windows 7 I had bought already separate legitimate Windows 10 Pro license key for the upgrade. I was able to go online and download the upgrade of Windows 10 and used my purchased license key to activate my updated.

  While doing the installation, there are some HP software that was still on the hard drive. I thought it would be good to have some additional security protocols, so I also installed the WinMagic Securedoc Bootloader v1.2.12 and saved the drive encryption HP with the security issues and password for secondary access.

  10 Windows has been activated and everything was beautiful. But when I restarted the laptop, I put my password for windows and then it goes to this screen of disc HP encryption rises. I put the password and it is accepted - and then the screen turns white... not offshore... jblank TEU with a cursor flashing that doesbn can't react to inputs.

  I tried leaving it for a day or so and still nothing.  There is nothing I can change in the configuration of the BIOS that works so far.

  I also tried Reimage download on USB and re-creation of the sequence of boot, but not good. Even tried a boot drive, but nothing there either. I'll try again.

  I don't know where to go or how to get beyond the screen of HP encryption.  I am pretty good at following directions, I don't know coding, but may do what you suggest to help me fix this problem.

  Can you help me?

  Sorry... I missed the part that you have a license Win10.  I thought you were trying to activate 10 using the OEM HP license and causing problems.

  I do not use HP encryption applications - as having recently completed a career in the InfoSec, I personally focus together on the encryption of the PC to be laughable-, but my guess is that you are basically out of luck.

  If it was my drive, I WIPE the drive of all its content and then again install Win10.  A good product to do i.e. DBan: http://tiptopsecurity.com/how-to-securely-wipe-your-hard-drive-with-dban-erase-your-data-for-good/

  Once your disc is clean, then simply install Win10 on it.

  That said, with a bit of luck, one of the HP EXPERTS will probably come along and tell you how to get around their encryption.

  Good luck

• Satellite L50-B-1XF - Win 7 64-bit drivers and software

  Hello

  as I can't find anything on my model - Satellite-L50-B-1XF (PSKTUE-04C00WGR), I'll try it here...

  I bought two of these (one for me, one for my wife) with installed Win8.1.

  Well well... no need to say that it is one of the worst OS I have ever seen and since Tru64 Unix and VMS, I've seen a lot.

  Anyway. I went down to Win7 Professional SP1 64-bit - full re-installed all updates installed, etc.

  Now, I have the problem that I can't find anything on the camera.
  Is there any support here page where I can download the appropriate drivers for Win764Bit specially for this model?

  Help here is appreciated!

  Hi Stuart

  The situation is quite simple and clear, then I really wonder that you were not able to find drivers, tools and utilities for your laptop model.

  For European laptops, you can download all the stuff on http://www.toshiba.eu/innovation/download_drivers_bios.jsp
  It is European support page to download the drivers. I found your model and your laptop model is fully supported for Win7 64 bit so you can find all the drivers, tools and utilities there.
  Please check and if there is a problem with the installation let us know

• After the upgrade to win 7, it no longer recognizes my dvd/rw drive

  My gateway does not recognize that I have the dvd player

  Hello

  As the system originally had a different version of Windows do you run Upgrade Advisor and
  see the compatibility for CD/DVD compatibility Center (and other devices according to the needs).

  Windows 7 Upgrade Advisor - Please run this now. http://www.Microsoft.com/Windows/Windows-7/get/Upgrade-Advisor.aspx

  Also check the Compatibility Center (for the main devices)
  http://www.Microsoft.com/Windows/compatibility/Windows-7/en-us/default.aspx

  Check with the system manufacturer and the manufacturer of the device for more information about the drivers for Windows 7.
  (BIOS, chipset of low-level drivers and other main device drivers).

  Check with the drivers, documentation online and Support technique Gateway.

  Gateway drivers and downloads
  http://support.gateway.com/support/drivers/dlcenter.asp

  Technical support Gateway
  http://support.gateway.com/support/?cmpid=topNav

  Door Documents
  http://support.gateway.com/support/SUPINFO/index.asp?cmpid=topNav

  --------------------------------------------------------------------------------------------------------

  Follow these steps to remove corruption and missing/damaged file system repair or replacement.

  Run DiskCleanup - start - all programs - Accessories - System Tools - Disk Cleanup

  Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN

  sfc/scannow

  How to fix the system files of Windows 7 with the System File Checker
  http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.html

  Then run checkdisk (chkdsk).

  How to run check disk in Windows 7
  http://www.SevenForums.com/tutorials/433-disk-check.html

  -------------------------------------------

  Check these:

  The DVD player does not work after I installed Windows 7 - here are the different readers from Sony
  However the same issue could have an impact on your drive.

  http://support.Microsoft.com/kb/975270/

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.Microsoft.com/kb/982116

  -------------------------------------------------------

  If the system can run Windows 7 AND there are drivers for the devices that these might help:

  References to Vista also apply to Windows 7.

  Step 1: Please do all the same underneath if you did some before as is often total
  a process that solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
  Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
  RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
  below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a coward
  cable or slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  Try this fix manually if the Fixit 314060 does not work
  http://www.pchell.com/hardware/cd_drive_error_code_39.shtml

  Your CD or DVD drive is missing or is not recognized by Windows or other programs-
  a Mr Fixit
  http://support.Microsoft.com/kb/982116

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
  Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error during Windows Vista
  Setup after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  ===============================

  Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
  Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
  do it right.

  Did you follow the Troubleshooting Guide for the reader who still does not work? There are
  the entries in registry that the troubleshooter does not solve and those who "might" be the cause.

  Check with your Maker system and a device for the two possible firmware updates and the
  correct registry entries for your car.

  Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
  as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
  the parameters.

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  -----------------------------------------------------------------------

  You can probably find more info here and maybe even the exact registry for your CD/DVD settings
  drive from someone with the same model.

  Forums - a lot of expert real help
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
  nothing change) - find the DevManView device and then make a right click on it free in RegEdit.

  DevManView - free - an alternative to the standard Windows Device Manager, which displays all the
  devices and their properties in flat table, instead of the tree viewer
  http://www.NirSoft.NET/utils/device_manager_view.html

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• RALink wireless LAN 802.11n card and my WIN 8 64 bit PC error Code 31: no driver updates available

  22/12/2012 bought ASUS CM6780 PC running 64-bit. RALink Wireless LAN crashed my system twice in 10 months. ASUS support allows only a "System Restore" which means you start from scratch with ALL your programs, updates etc etc.
  I get the error code indicating 'Bad Image' with several pop-up window for what I am running, and the Ralink Lan has an error code 31 showing Windows cannot update.
  I have my 1 year warranty AND a 3 year warranty, I purchased in addition to this, but the ASUS support is lame. Only help to restore the system not to find a real solution, and when I ask a new LAN card, they do not respond.
  Is this a problem with updates of Windows or Ralink?
  Please advise, downtime for each episode runs more than 24 hours, restore my programs and update everything. I'm ready to trash or sell it!

  Send the minidump to analyze what is causing the BSOD,

  This device does not work properly because Windows cannot load the drivers required for this device. (Code 31).  So install the Ralink wireless driver.