Portege S100: Unable to change JBOD to 1RAID-0 after replacing HARD drive

Similar Questions

• I'm unable to open Adobe Illustrator on my newly replaced hard drive in MacBook Pro.

  I am unable to open Adobe Illustrator on my newly replaced hard drive in MacBook Pro. I get "Error 16". I get a window that says: error in Configuration please uninstall and reinstall the product.  If this problem persists, please contact Adobe technical support help and mention the error code displayed at the bottom of this screen.  Error: 16 http://www.adobe.com/support/

  If you tried to transfer the software from one drive to another while it is probably the cause of the problem.  Adobe software must be installed using installation files.

  Did you uninstall and reinstall as the message suggests?  Uninstall and use the CS cleanup tool before you try the reinstall.

  Adobe Creative Suite cleanup tool

  helps resolve installation for CS3 thru CS6 and creative cloud problems

  http://www.Adobe.com/support/contact/cscleanertool.html

  Download and Installation Help-
  https://helpx.Adobe.com/download-install.html

  http://www.Adobe.com/downloads/other-downloads.html

• Replacement hard drive for Portege P2010 - part number required

  Can someone tell me what is the part number for a replacement hard drive for Portege P2010 is? It has the latest version of the BIOS installed, if the capacity of the HARD disk can be greater than the original 30gig?

  Thank you

  Martin

  Hello Martin

  Unfortunately I was found no specific information. If I'm right, this unit needs 1.9 HDD and I think it can be much more expensive as 2.5 standard.

  Check it please this page http://www.laptopbits.co.uk/Database_files/Toshiba_Portege_2000_and_2010_series_spares.htm
  You will find a few pieces of upgrade for your device.

  Good bye

• How can I reinstall the CC without having to start a new account after a hard drive change?

  How can I reinstall the CC without having to start a new account after a hard drive change?

  Just got my PC back from repair with a new drive installed and al, I see for the CC options for new accounts to create, I already have one so I want to reinstall my account without having to pay for a new account.  Can someone tell me how to do it please?

  Hello

  Please visit the given link to download CC: download and install Adobe Creative Cloud applications

  * Connect with your Adobe on which you have registered the product ID.

  Concerning

  Bianka Attre

• After the hard drive failed, I changed my computer and reinstalled LR5. I've updated LR5 a few weeks before my computer crashed, so for you my serial number is up-to-date. After having read a few tutorials, I suspect this deactivation were not made before

  After the hard drive failed, I changed my computer and reinstalled LR5. I've updated LR5 a few weeks before my computer crashed, so for you my serial number is up-to-date. After reading some tutorials, I'm suspecting this disabling was not made before reinstalling... Recommendations on resettlement in this case?

  You actually have a renewal LR5 problem or ask yourself what you need to do?

  Download and install the update LR 5.6 from here: http://www.adobe.com/downloads/updates

  Enter your LR 5 serial number and you should be ready.  If something doesn't work, then, please describe the problem in detail.

• Portege S100: How to change the RAID in the BIOS

  Change the BIOS setting for Portege S100 of JBOD to RAID0, I hit space on Exectute creation and enter the key of type string in the manual, and press "enter".
  Settings and then return to existing arrangements and not the new RAID0 configuration setting that I selected.

  I stayed in this part of the day / night looking at different positions, but I don't see anything wrong with the data entered.

  This is the same as that recorded in this link: -.
  [How to change the RAID configuration | http://aps2.toshiba-tro.de/kb0/TSB6901K60006R01.htm]

  I'm now at the end of my home, I just wanted to install new HDD WD and new installation of XP Pro, is - it too much to ask?

  Maybe it s a silly question but; have you installed the second HDD to the Ultra Slim Bay?
  The RAID did feature is available when a second HDDD is installed in Ultra Slim Bay.

  If the second HDD was inserted and then change the RAID in the Windows operating system.
  There should be a Toshiba RAID Console.
  You can use this console to create or manage a RAID array.

  To start the utility, click Start, point to all programs, point to Toshiba, RIAD-tap and click RAID console.
  It of possible to change the RAID1 (mirroring) of a configuration non-RAID (default).

  But note; When RAID1 is set, you cannot change your settings unless you completely restore your preinstalled software.

• Portege 7220 - replacement hard drive problem

  I have a Portege 7220 CTe Windows 98se. The hard drive is deteriorating slowly (bad sectors), so I decided to replace it. The old drive is a Toshiba 6 GB. The news is an IBM/Hitachi Travelstar 10 GB - so-called and apparently unused but dated from 01 Sept.

  Summary: the drive has worked once in the Portege, but doesn't work anymore. It continues to operate through a USB interface to another system.

  I did the following. (I don't know that there are a lot of unimportant details, I just can't tell who might be relevant):

  -Checked the new drive with Hitachi Drive Fitness Test. Ran on the Portege, booting from CD in the docking station. The perfect extract player.
  -Make a backup image the old drive on another computer (XP desktop computer) using a USB box and the reflection of Macrium.
  -Restored the image to the new drive (using the same USB box).
  -In Ran XP Scandisk and defragmentation on the restored drive (no problem, does significant defrag)
  -Cleanly removed from the XP system USB and road of the housing
  -Put the new, restored in car in the Portege and turned on.

  The system could not start, (indirectly) saying that HIMEM. SYS was missing. I plugged the drive into the XP system. Indeed \WINDOWS\HIMEM. SYS was missing, along with the rest of the content of \WINDOWS. The rest of the matching content to the backup. ???????

  I copied \WINDOWS to the backup image to the new drive. Neatly removed from the XP system and put in the Portege.

  Starting from Win98 system. I tried to start a random application and become system that is not responding.

  From this point, I may have not all the actions in the order, but I doubt that counts. I tried the following:

  -Hitachi Drive Fitness Test running. He first found the drive but returned an error 'drive not ready '. After repeated attempts to re-seat assigned, check on the XP system, etc it is unable to find the drive to all the
  -Go into the BIOS at startup. Sometimes found the drive, sometimes not.
  -Office XP still recognizes the player very well via the USB interface. ScanDisk is happy with it, including the surface scan. Hitachi utility only works with ATA or SCSI disks, and I do not have an ATA desktop-laptop adapter.
  -Made a new restoration of the saved image. It worked well, but the Portege wouldn't even find the drive.
  -Tried the old drive and a travelstar 6 GB to another system in the Portege. Both work very well.
  -Tried the new disk in a Portege 7020. Do not just like in the 7220.

  I thought maybe it was a power issue. But the two Travelstars (one that works and a new one that doesn't) are valued at 500 my. The old disk from Toshiba which also always works is estimated at 700mA.

  Any ideas would be greatly appreciated.

  Apparently, there's something wrong with your 10 GB travelstar, maybe the MBR or the boot sector

  the fact that you can read with a USB connector doesn't mean that the HD is correct, since you do not need the boot sector of this way

  I would advice to wipe it completely (with cleandisk or boot-TI-NG), make a new partition with fdisk and reformat the HD in fat32 format

  That to do a fresh install with W98, or better: W2000, which spans a 7220 easily and is much better

  It is best to copy the directory to install W2000, integer i386 installation CD - on the 10 GB HD (which can be done on another PC with a USB connection) and begin the installation of BACK with Windows NT. EXE
  More information about this problem, which you can find here:
  [t 23921]

• Impossible to change the location of backup to external hard drive

  * Original title: backup location

  I need to change the location of backup on an external hard drive (I).  When I go into Control Panel, backup and support, it seems that the location is currently (D).  To change this, I select 'change settings '.  Then, the computer opens a new window for "Set up Backup" and begins to launch.  However, whenever I try to do the answer comes back that the computer is unable to start the program because of the error (0 x 80080005) of running the server.  I don't know what to do from here.  Can anyone offer any guidance?  Thank you.

  Hi Janis,

   
  The probable cause of this problem could arise from the security of the software interrupt services to change backup settings.
   
  I suggest you follow the methods below and check if it helps:
   
  Method 1: Temporarily disable the antivirus on the computer running software and check if you are able to change the backup location.
  Reference: turn off the antivirus software

  http://Windows.Microsoft.com/en-us/Windows/disable-antivirus-software#1TC=Windows-7

  Warning: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks.

  If Mode 1 has not resolved the issue try MOde 2 which follows below:

   
  Method 2: Put the computer in a clean boot state, and then try to change the location of backup on your external hard drive again:
   
  How to perform a clean boot in Windows

  http://support.Microsoft.com/kb/929135/en-us

  Note: After troubleshooting, see the section «How to reset the computer to start normally after a boot minimum troubleshooting»

  Additional information:

  Change when you save your files

  http://Windows.Microsoft.com/en-us/Windows7/change-where-you-back-up-your-files

   

  Hope this information helps, just reply to the State of the question to get help.

   

• change of loan only on the external hard drive after installation of el capitan

  Hi all

  My external hard drive has changed to the loan only after I installed El Capitan. In the read window information, the "locked" icon is gray out only the "shared folder" is available. Any suggestions or solutions?

  Thank you Trudy 113

  Please send a wink to the Panel of the window read share information and permissions.

  To post a screenshot

  1. Press command + shift + 4, that will change the cursor to the line of sight.
  2. Hold down the mouse button and the collimator allows you to select the part of the screen you want to capture.
  3. Release the mouse button and the image will be saved on your desktop.
  4. Click on the camera icon in the toolbar of the message forum Editor.
  5. Drag the image on the button select a file and click the Insert button.

• Portege R500-100 - drivers after format HARD drive

  Hey,.

  First post so go easy :)

  I reformatted my hard drive the other day, but the drivers for my laptop support is poor.

  The audio drivers are not working, I have several unknown devices in Device Manager in need of drivers, but I don't know what drivers to install.

  Anyone could point us in the right direction?

  Its a r500-100

  Hey Buddy,

  Why you are not satisfied with the Portege R500 driver support? I mean can you all the drivers on the site of Toshiba, and for most versions of Windows. Just follow the link posted by Al - eX.

  And you should install all the drivers you can find on the Toshiba site. After that, you use all the functions of your mobile phone and you get back to factory settings.

• Portege M200 - where to find T & D Utility FD after replacement motherboad

  I just replaced the motherboard on a Portege M200.
  Installation guide States, you must run the FD T & D after replacing the motherboard and run the initial configuration option.

  Nobody knows what is and where can I find this utility?

  Its also equally useful for the definition of DMI information.

  Hello

  As far as I know these utilities are special tools that are not designed for public use. Only the Toshiba authorised service provider got such tools and utilities.
  Because of this, I put t see another option to contact the ASP in your country and ask for help.

  Greetings

• How can I change the icon associated with an external hard drive that is displayed in my computer

  When I double click the icon my computer on my Seagate external desktop hard drive does not display the correct icon. It displays a blank page with the upper right handed with a superimposed replica of a small screen.  I really want to show an icon that looks like the real thing as stated in the icons folder.

  Hi PhilipRoebuck,

  (1) do you get an error message when you try to open the external hard drive?
  (2) where there are changes to the computer before the question?
  (3) is confined to a specific icon?
   
  See the following:
  Method 1:
  Icons change incorrectly in Windows
  http://support.Microsoft.com/kb/2396571
  Important Before run you this difficulty, save your data and close the application. After you run the difficulty, your computer will reboot after 10 minutes.
  Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:
  How to back up and restore the registry in Windows
  http://support.Microsoft.com/kb/322756
   
  Method 2:
  How to change the default icons for folders in Windows XP
  http://support.Microsoft.com/kb/310192
   
  I hope this helps.

• Unable to see the number of files on the hard disk on Windows 7 computer after the hard drive crashed windows xp system

  Original title: unable to see many folders on separate conputer

  I was using windows xp with service pack 3 and windows 7 on a separate booklets. Suddenly the laptop with XP crashed... The hard drive was Ok - cased with a USB port, but now on the connection with the computer laptop windows7 I saw no many records there - pls help

  the system crashed in fact as I was reading the (visualization of the pictures - JPEG, bmp and also some books .pdf) & suddenly.  In the Xp laptop NVIDIA graphics card was there.  He lacked RECENT documents, I see

  Hello

  Try the methods provided below and check if the problem persists.

  Method 1:

  You can make the disk check to make sure that the hard disk is not damaged.

  See the link below for more information on disk error checking in Windows XP.

  How to perform disk error checking in Windows XP

  http://support.Microsoft.com/kb/315265

  Note:

  Running chkdsk on the drive if bad sectors are found on the disk hard when chkdsk attempts to repair this area if all available on which data may be lost

  Method 2:

  This issue could also be linked to the virus/malware on the hard drive that may have caused the crash of the system.

  Click on the link below to download and run a full scan of the system using the Microsoft Safety Scanner.

  Microsoft safety scanner

  http://www.Microsoft.com/security/scanner/en-us/default.aspx

  Note:

  The data files that are infected must be cleaned only by removing the file completely, which means that there is a risk of data loss.

• Unable to see the new files from the external hard drive in Windows Media Player library

  Original title: music is dead

  Windows media player does not recognize my external hard drive on all my computers windows 7, but works fine on my xp. has taken the laptop shop they led produced songs media player then reinstalled them, and it worked. but when I added more songs on the ext. harddrive and tried to play on windows media player 7 it does not find new! can't afford to take to the store whenever I have download music and want to play on my Media Player 7. is it auto recognition? When I plug the ext. harddrive inside automatically so reads the news on it?

  It has been fixed thought

  I had posted a question on my Ext. harddrive, my windows xp Media Player recognizes new music I have add out of it, but all my computers which are used to windows 7. then I myself especially when I add the new music on the hard drive for media playyer on xp I have spend the toolbar and click on file, then click Add to library computer search and it adds to the media player library. but windows 7 does not have this option. I noticed if you click file, and then manage libraries, and then the music lets me add my Ext. harddrive (e drive) to the library list. on a computer it support of new music and videos found on the hard drive, on two computers it just music, so I downloaded a song and a video on the hard drive, plugged into the computer and media player says that it has been updated of library, and yet there they never found the new files. Why have they changed? XP was so easy. new is not always better!

  Hi Bob,

  According the description preceding, Windows Media Player is not picking new music on the external hard drive.

  I suggest you to perform the following troubleshooters.

  Open the troubleshooting Windows Media Player settings Troubleshooter

  http://Windows.Microsoft.com/en-in/Windows7/open-the-Windows-Media-Player-settings-Troubleshooter

  Open the troubleshooter in the Windows Media Player library
  http://Windows.Microsoft.com/en-us/Windows7/open-the-Windows-Media-Player-library-Troubleshooter

  Post us the results once you try the steps above.

• Unable to complete R & R B/U for external hard drive

  I tried to fill a b/U of a R51 to a 500 GB hard drive Toshiba external
  using R & R v4.23. The P/hold 54% with 48 minutes from the end.
  I tried both the simplified and Settings Advanced: initialize the p/C,.
  then the backup media, then the Predesktop Installer, then the B/U, stop
  at 54%, every time. The HD is 38 GB; Preload IBM 34GB and 4GB Service.

  After dropping out, I have at the end of the B/U using Manager tasks, and when R & R is
  selected again, "your system backup" comes with a 0% and no activity.
  Have to close it with the Task Manager.  Then remove R & R, reinstall it, do it again
  with the same results.

  I used the command CHKDSK, reformatted the external drive NTFS and FAT32. Anti
  disabled virus. Any ideas?  I used R & R on other systems without installation
  problems. He is obviously a very old system and probably not worth too much effort
  to repair. Just thought I would check for any obvious solutions.

  Uninstalled & reinstalled R & R 4.23
  Backup to USB HD, picked up again exactly 54% complete, 41 minutes remaining
  Manager to the end - tasks does not not to Cancel order
  Of the rr.log:
  Any user found to run the command "C:\Program Files\Fichiers Files\Lenovo\msgbox.exe", waiting...
  Start/run services.msc
  Check the Terminal Server - disabled Services
  Automatic change and then start
  Reset
  Success! -message to restart "the last backup did not complete...". "YES to start/continue.
  Open R & R - backup current and then continued to the end.