Possible redirection problem - Google redirect spy

Similar Questions

• possible redirect Web SSL VPN to another external ip?

  Hi, it is possible to redirect the web ssl vpn to another external ip of my external range or could I do not use the external interface?

  For example:

  ASA outdoors: 213.23.4.50 (https://213.23.4.50)

  Redirect outside: 213.23.4.51 (https://213.23.4.51)

  same question to redirect the vpn client ip address external to the other that the IP outside of asa.

  concerning

  Jason

  Jason,

  Pretty easy

  BSNs-ASA5520-10 (config) # webvpn
  BSNs-ASA5520-10(config-WebVPN) # port?

  the WebVPN mode options/controls:
    <1-65535>The WebVPN Server SSL listening port. The TCP 443 port is the
  by default.

  Please note however that your users will use

  https://my.domain.tld:port

  to connect... even for clientless and SVC.

  Marcin

• Are possible redirects for specific products?

  We move some of our product catalogs, is it possible to perform 301 redirects for specific products?

  You do not have the URL redirects here. In the Site Manager? Redirects from URL, you have a spreadsheet import.

• Questions about circuit RC phase difference (possible timing problem)

  Hello

  Here is the program that I use to measure the phase difference in an RC circuit. Simply generate a sine wave of 2 kHz in LabView and send it to the circuit using an analog output. Then I measure the exit sinusoid using an analog output. I also measure using n oscilliscope. I can clearly measure the difference in phase with the oscilliscope and know that it is about 1.4 radians.

  Problems with the program:
  Phase difference different measured each time the program is run for the circuit. It is never as good.

  Possible causes:

  You will notice by looking at the vi that I measure the phase from the signal generator. Can I use a second analog input to measure the sine wave, as it came out at the beginning of the circuit?

  I think it's a timing issue. While the phase difference is constant each time the program varies each track. So the time that each measurement of tone starts its first measure seems to be different every time and causes this reading of different phase.

  The card that I use is a PCI-6221, is there a timing problem associated with switch for input and output audio acquistion or are they separated.

  Is anyway to ensure that two key measures measure phase at the same point in the (real) time?

  I would really advice or changes to the program - could someone offer me (I am a student and LabVIEW is not on our program so I have no support, but I use it for my project (OH!))

  I would certainly acquire two signals.  Food for the analog output right back into an analog input, then your signals filtered in another.

  Initially, I would feed the two analog inputs of the analog output and measure the delay in phase due to the multiplexed A/D on map.  Once you have this measure, you can feed in the filtered signal and then measure the difference of phase of this signal.

• Possible to integrate Google play application Adobe AIR services?

  Hello Adobe Experts,

  Need help!

  Is it possible somehow to integrate services to game google to Adobe AIR app, not through the Native extension?

  I mean, can I integrate as a dependent of my AIR application library? I know how to group as part of the Native extension, but the challenge here is if I use some other DONKEY which also comes with the library of game google services then it gives conflicts. So thought if there is any way to integrate google services play all together separately to my AIR application.

  Future prospects for the answer.

  Thanks in advance.

  Oh my God, I'm a fool! I'm sorry, I didn't know that he didn't not apply to Android...

  You can try another DONKEY, I guess that this is a business option: distriqt / / air native extensions

• Satellite A60 - possible ram problem

  I have a satellite a60 he says he has 256 RAM. on aol checking my computer tells me that I have only 192 RAM anyone any idea, what the problem might be?

  [Edited by: admin on 22 May 05 20:28]

  Hello

  I suspect that your RAM is shared with your graphics (usually 64 MB) so even if you actually 256 MB RAM, 64 MB is pré-alloué graphics use 192 MB. Your computer AOL chack reports available rather than the actual RAM RAM

  HTH

• Mac works oddly, possible virus problem

  Now, this might be a bit long, but I want to explain my situation: my Mac version is 10.6.8 and I have Windows Bootcamp that divides my 500 gbs equally between the two parties. I use only 20,99 gbs on the side of my Mac and I have only a few applications I've downloaded myself (Chrome, two games (OFF and Minecraft which has a few mods), the Unarchiver and Adobe programs such as Photoshop and Flash). However, I have more (I removed) Safari and Garage Band. The reason why I deleted the Safari is because it does not block the dangerous ads. It is an ad ' Web Cam S *' that I met on a fake Wikipedia who made fun of Youtubers (forget the name of it and never come back to it) which forced me close my Mac because it will turn off and an announcement on YouTube who wanted to use 5 mbs of my data (I stopped my Mac new cause he kept asking when I was denied several times). I can't remember anything for download, but I don't know how to work the virus. This return all happened in August 2015, but since December 2015, my Mac fan started running loudly when he wakes fashion 'sleep' with any of the applications that are running. My Mac also gets is more cool as it allows when it is in "standby". I don't know if it's advertising or there is something wrong with my Mac internally (son, dusty in bulk). Six years ago, but it still load the Web pages and applications as it allows before the ads. Thanks for this reading, I was not able to find an answer that has cured my problems. PS: I don't want to download apps 'useful '.

  I understand how you feel when you say that you do not want to download useful applications.   I'm guessing that is probably based on the experience gained.   However, there is an application that we use here and is generally well regarded by members.   Please download and run and publish the results as a response here.

  It will not immediately solve your problems, but it will allow us to evaluate your machine and recommend a plan of action.    The fact is, there are too many alternatives for us to guess what your problem, go inside your machine.   What will be shown will not include anything private or potentially dangerous; only technical facts.

  Scroll down to the download.      http://etrecheck.com/

  With respect,

  71

• HP laptop Pavilion 17-e040us - Possible fan problem

  Hi all.  I think I have a fan problem.  The fan seems to run all the time... at least for the past 3 or raining days, but not fort, with air alternating hot and cold, of the events.  I looked at the events surrounding the outside of the computer and it does not seem to show the accumulation of dust... but even with appropriate glasses, I'm not able to see if there is dust or not... is old or in my case being old causes sight problems!  I also used the diagnostic software to see if any hardware has failed.  The results showed that the computer hardware is correct.

  Then you clean the vents (the article says that it is acceptable to use a hair dryer)?  In addition, open the back cover of the laptop to clean the fan inside if it has dust?

  Article also says to turn off the computer and unplug the power adapter before spraying compressed air.  Also if you use a blow dryer on the cool setting?  If so, what is the power adapter and how to disconnect it?

  Right now I am using the wired option.  I just need to remove the power cord at the back of the router to disconnect.  However, then the computer is wireless... How to turn off the wireless feature... so I can clean the fan/vents?

  Thank you.  I really don't miss my XP version!

  By blowing air through the vents of your laptop, you are forcing air through the fan. In a laptop, this remove most of the dirt and allow for better air circulation and cooling. This isn't the case with a desktop computer and that's why the video demostates office clean the fan.

  I suggest removing the battery is because with it in place, you can accidentally turn on the computer. With the sector/charger adapter unplugged and the battery removed, there is no chance of the computer starts.

  If you have any other questions, feel free to ask.

  Please click the 'Thumbs Up' white LAURELS to show your appreciation

• Speed problems according to the channel in which I connect - Possible hardware problem:

  Hello

  I bought a R8000 about 1 month, and it worked pretty well. Last week, I read a review on the router suggested what a turn on the Smart Connect. That's when the problems started.

  -Panda USB wireless that worked perfectly started to have speeds of 1.5 Mbps when my service is Comcast 150MBps explosion. Before turning on the S.C., it reaches that speed easily.

  -After the filming of Smart Connect, did not improve the performance of the USB dongle. It is remained at 1.5 Mbps to 3MBPs. I tried to fix it for a week now.

  -J' I reset the modem (button reset button for 10 seconds), configured my router again and added to my dongle is malfunctioning, the router started having trouble to detect my external WD "My passport".

  Today, troubleshooting the wireless dongle with Panda, I changed the channel 5 GHz at the elementary school and the speed is back to 170 Mbps. The router is kept at approximately 3 M from the computer without any obstacles between them.

  Finally, the streaming of my router (with cable) to my TV using DLNA sometimes stutters. yesterday, she even caused the TV to not recognize the transmitted file.

  Can you help me troubleshoot the router more far to find if it is defective?

  Thank you

  As I started the topic, I would give it a closure. My problem was that I had a USB Wireless Dongle of Panda, who performed in the secondary channel (high way) but ridiculously low in the primary (Channel Low). As I had Smart Connect lit, I couldn't control my connected computer channel and appeared the problem was with the router.

  That said, I noticed a better balance between devices when I disabled the dynamic QoS option. I don't know if the algorithm for dynamic QoS is simply wrong or its implementation by the current firmware (V1.0.3.4_1.1.2) is buggy.

  In any case, currently, everything works with me. Explosion of Comcast 150Mbps and rapid tests is between 157 to 153Mbps in tests using a channel 5 G.

• HP Pavilion 15 Possible network problem

  Bought a Hp Pavilion 15-2513 p original supplied with Windows 8.1

  However, I noticed that when I plug in an ethernet cable and perform a speedtest, speeds are massively a bottleneck. I think it's a driver issue, but I don't know which driver to use. I went to the Device Manager and noticed that the laptop has problems with Bluetooth and an unknown PCI device.

  I also know of the network components is a PCI device so it could be related. A few tips on which driver should I use?

  I have attached a screenshot of the Device Manager to help:

  

  Hello:

  If you have installed windows 7 you need these drivers...

  Last one for the wireless...

  http://h20565.www2.hp.com/portal/site/hpsc/template.PAGE/public/psi/swdDetails/?spf_p.tpst=swdMain&spf_p.prp_swdMain=wsrp-navigationalState%3DswItem%253Dob_131223_1&javax.portlet.begCacheTok=com.vignette.cachetoken&javax.portlet.endCacheTok=com.vignette.cachetoken

  Bluetooth (Bluetooth driver):

  http://h20565.www2.hp.com/portal/site/hpsc/template.PAGE/public/psi/swdDetails/?spf_p.tpst=swdMain&spf_p.prp_swdMain=wsrp-navigationalState%3DswItem%253Dob_130390_1&javax.portlet.begCacheTok=com.vignette.cachetoken&javax.portlet.endCacheTok=com.vignette.cachetoken

  PCI device: you want the first driver on the list...

  http://www.Realtek.com.tw/downloads/downloadsView.aspx?langid=1&PNid=15&PFID=25&level=4&Conn=3&DownTypeID=3&GETDOWN=false

  Ethernet: Download and install the 3rd driver on the list.

  http://www.Realtek.com.tw/downloads/downloadsView.aspx?langid=1&PNid=14&PFID=7&level=5&Conn=4&DownTypeID=3&GETDOWN=false

  None of these devices that need drivers should have an effect on the performance of the ethernet cards / wireless.

  The only thing that can help is the new wireless driver.

  If it makes not a difference, then I don't know what could be the problem.

• All computers on a network cannot browse a specific external site - Possible DNS problem?

  Hi all

  The categories are too vague hope so I'm in the right forum... I have IE8, Windows 2008 R2, Question of DNS...

  We migrated from Windows 2000 to a Windows 2008 R2 domain 2 months ago. There has not been all problem reports since then and I'm to understand that all of their sites they are functioning normally, have been finding work subsequently... Now, the strangest thing is that all the sites that they want to go to all work properly with the exception of this specific site (www dot careerbuilderdotcom) so far.

  Checked the PING WWWdotCAREERBUILDERdotCOM

  (in case of failure may be due to the blocked ICMP) several computers and it does solve one of their IPS (208.82.7.50), indicating the DNS works and solve correctly... Tested accessing this site in particular, many computers and fails this site only. Tested also the computers outside the network to access the site in question and that they can browse correctly indicating that this is NOT the site...

  Checked entered DNS and restart the DNS service without result. Does DNSFLUSH on all of the computers in question and are still unable to access this site.

  It seems not to be a DNS issue. Can anyone provide additional lighting at the entrance and knowledge to solve this problem?

  Hello DASNetSys1

  If the suggestions provided by Ing. Ladislav Cermak do not solve your problem then please return the question in the Windows Server forum from the link below. Thank you.

  http://social.technet.Microsoft.com/forums/en/winservergen/threads

• DVD video disc play is not in Windows Media Player, possible decoder problem

  A DVD was made product with a video camera of the dance show to my child. However, the dvd on my hp Pavilion 772n burner will not play it. The operating system is XP and when I try to play the DVD in Windows Media Player, I get a message "...". compatible DVD decoder is not installed on your computer. Interestingly, the DVD disc plays in a DVD VCR connected on television.

  What should I do to play the dvd on the pc?

  On XP you must install software that can play DVDs. Both Vista and Windows 7 that include by default.

  Here is a (quite old) Microsoft article describing what you see: http://www.microsoft.com/windowsxp/using/setup/expert/bridgman02april15.mspx

  On XP, I used to use the card nVidia PureVideo Decoder for playback DVD with Media Player. It seems to still be available, but is chargable:http://www.nvidia.com/object/dvd_decoder.html

  You may want to google for a free DVD decoder for XP.

• Java has stopped working. possible configuration problem

  My java stopped working Saturday.
  I tried to uninstall and reinstall. someone said that my being, I got hacked and there is no way to fix it. I think that configuration is mess up I can't even install updates window. Not sure how to restore my configurations then that I can get back operational. I uninstall java on Monday and I still try to reinstall. any help would be great. Thank you.

  Hello

  1. at the outset, what was the exact error message?

  2. what happens when you try to install Java?

  3. what exactly happens when you try to install updates via Windows updates?

  4. What is the name of the updates that fail to install (and the code number and the message KB)?

  5. are you aware of any changes made to the computer, before the show?

  Given that you have uninstalled Java, download and install the latest version of Java available when the computer is on a clean boot.

  Step 1: Clean boot.

  Perform a clean boot on your computer.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  http://support.Microsoft.com/kb/929135

  Note: once you have determined the problem by using a clean boot procedure, follow step 7 in the article to restore your computer to normal startup.

  Step 2: Download and install the latest version of Java on your computer.

  http://Java.com/en/download/index.jsp

  For issues related to Windows Update, please respond with more information.

• I lost all ability to do things, possible permissions problem in Vista

  I lost all ability to do things that I use to type my administrator password for. I think that some permisssions is changed could start it. any suggestions?

  * original title - I have ' administrator password - permisssions *.

  Hi scottkobold

   

  1 have. what changes you done recently on the computer?

  2 are you facing problems with programs that need administrator access?
  3. have you made changes to user account control settings?

   

  Please refer to the below links and check if changing the behavior of the UAC message settings helps you resolve the issue.

  http://Windows.Microsoft.com/en-us/Windows-Vista/how-do-I-change-the-behavior-of-the-user-account-control-message

  http://Windows.Microsoft.com/en-us/Windows-Vista/your-permission-please-understanding-user-account-control-in-Windows-Vista

  http://Windows.Microsoft.com/en-us/Windows-Vista/what-is-user-account-control

   

  I hope this helps.

• Possible repaint problem

  Hi all

  I had a problem with my bb app, and another instance of the same question has been raised on another of my screens. The problem is when I delete a line in my objectlistfield screen showing until I have highlighted the area where the problem is and it sorts itself, it can become a little visible/invisible on some lines.

  The same thing just started happening on another of my screens after you add another manager of text boxes, buttonfields, etc.. This time the problem is triggered when I scroll horizontally (and then scroll back the way I came) in a horizontalfieldmanager with scrolling. The screen goes kind of visible/invisible (best way to explain it) until I highlight the affected area.

  I think it's something to do with the painting/repainting but I'm completely new to java/rim api so I really need some suggestions on what to try.

  the objectlistfield is a custom of mine class, it is added to a class of the screen. I use drawlistrow and navigationMovement to allow the highlighting of the line in case of development.

  Concerning

  Brendan

  Finally solved!

  I set up scrollchangelistener and that is the thing

  ' Public Sub scrollChanged (Manager, int newHorizontalScroll, int newVerticalScroll)
  {
  if(Manager == HM)
  {
  Invalidate();
  }
  }

  I know disabled has been mentioned before, but find out where invalidate was my problem. as many events!

  Thanks for your help

  Concerning

  Brendan