power output of the spectrum in table

Similar Questions

• Power output during the disk check currently not able to boot to the desktop

  Power output during the disk check.  Now, does nothing.

  I started my system, he said to check the disc. The disk check began, he had run for a while. Then my power is out for a few seconds. Once the power was back on that I tried to reboot and nothing. The monitor shows no info yet. Just black says no signal and turns off. I have no option to boot or anything else besides. What I can do. Thank you

  Hello

  You did it of any material changes or software on the computer before this problem?

  You can connect the monitor to a different display port or connect another monitor if possible and check if it works very well.

  If the monitor is right, it implies that there is a problem with the graphics card or motherboard. In this scenario, I recommend you contact the manufacturer of your computer for help.

  Hope the helps of information.

  Concerning
  Joel S
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• How to insert the output in the Oracle database table records

  Nice day

  I have two tables (table A and table B) in my oracle database I created a process for mapping from Table A duplicate records to Table B, and the result (reports) must be inserted into the Table B. I can't make this process. Can someone help me please.

  Thank you and best regards,

  Muhammed Faraz

  Hi Muhammed,

  You will need create an export job and set up a new job as a result. Take a look in the help topic "export data" as he will explain the different options [Add/Remove and insert/etc.].

  Thank you

  Nick

• What is the power output on the wrt1900acs usb3 and esatap ports?

  I have a variety of options for storage for use with my new router WRT1900ACS.  But I can not find how much energy is provided on the USB 3.0 port or port eSATAp (combo)?  Is there documentation available on these or does anyone know only?

  Thank you.

  @Cbarnhorst

  We would like to pass your case to our level support team second for assistance. Send us an email to [email protected] with your name and first name, email address, phone number, location and the link to this message from the community.

  Chiqui-17359

  Linksys technical support

• How to show the output of the signalexpress power spectrum in data dashboard

  Hey guys.

  I made a program that collect analog data from two sensors in vibration, and then I use the signalexpress power spectrum to get in the frequency domain.

  I would like to show the signals and the FFT in dashboard of data.

  It is not possible to display the data directly because the XY graph in data dashboard supports only the two figures on the right cluster table?

  Is it possible to convert data from the spectrum of power signalexpress table of cluster of two numeric values?

  Or any other ideas would be appreciated

  

  
  

• Pavilion 15: What is the power output of my USB port?

  What power is out of my USB port?

  I would like to know so that if I have a camera that will happily from there, I can try to connect to another so as to not be dependent on the presence of my PC.

  @Ruaridh: the HP Support Spec page shows your PC has a USB 3.0 port.

  These ports have two sides of different power, according to the purpose of the port output:

  (1) standard port USB 3.0 - 500 MA (0.5 a)

  2-port USB 3.0 - load 1500mA (1.5 Amps)

  You get the best support experience with, you use a USB 3.0. Those who can usually provide 2.1 amps.

  Good luck

  ========================================================================
  If you feel that my suggestions helped you, please click on the Thumbs-Up symbol; If they helped to solve your problem, please click "accept as a Solution.

  I'm a volunteer and I do not work for, or represent, HP.

• power oid process should be recorded in the ODS. Table ODS_PROCESS

  power oid process should be recorded in the ODS. Table ODS_PROCESS. but I do not see anything... and what are the commands to start/stop OID as do I, do me right if I'm not...
  
  oidmon connect = ldapdcx1 power
  oidctl connect = server ldapdcx1 = config oidldapd = 2 = 3 start/start instance
  
  SQL > select * from ODS. ODS_PROCESS;
  
  no selected line
  
  SQL > exit
  Disconnected from the database to Oracle 10 g Enterprise Edition Release 10.1.0.5.0 - 64 bit Production
  With partitioning, OLAP and Data Mining options
  [dcxnim01]: [ldapdcx1]: = > ps - ef | grep oidldapd
  Oracle 675894 1200310 0 09:16:40 pts/0 0:00 grep oidldapd
  Oracle 938116 1 0 Jun 22 - 13:50 / oracle/product/oid10g/bin/oidldapd connect = ldapdcx1 Pei 389-i
  3 - conf 2 - sport button 636 - sslenable 2 = 1085443401
  1327250 1 0 22 Jun - 179:12 oidldapd Oracle
  Connect = ldapdcx1 = 938116 = 1 worker dispatcher control = 2 debug = 33554432
  ConfigSet = 2 instance = button 3 = host 1085443401 = dcxnim01 trcdimension = 511 logchange = TRUE port = 389 sport = 636
  [dcxnim01]: [ldapdcx1]: = >

  What version are you using?

  To start the OID, you must use opmnctl command.

  Greetings.

• Low battery and go to the message of power output

  Recently, I got a low battery message asking me to switch to the diet - even when the power supply is already connected.
  Is it possible to "switch" to diet without taking out the battery?

  My battery seems to charge better with my machine on - is it possible? For example, the battery took not the overnight - don't know why. This was 6% this morning. Left the machine for an hour and it was up to 81%. I used it for another hour and it is up to 95%

  Moreover, I am in Egypt, where power cuts are terrible. I don't know if it is safe to run on power just with a surge protector or battery. Any advice?
  (Electricity cuts have already had on my CD player, coffee machine and railway even if they were all on the surge protectors low level).

  Post edited by: kateinegypt

  Hi Kate,.

  First of all, I highly recommend you a surge protector for your laptop, in fact I recommend to any PC anywhere.

  As for your battery charging, I knew this type of behavior when the laptop is connected to an AC power but still the battery will discharge. In my experience, this is caused by a passenger (fraction of a second) power loss of AC that causes the microcontroller to power switch to battery even though normal AC power is connected.

  The only way I found of reactivating a correct diet is to turn off the laptop and then put on as usual.

  I suspect that your laptop is affected in the same way.

  Good luck

• Satellite s3000-514 - need info on USB power output?

  Hello

  Please can someone confirm the output power of the USB ports on the s3000-514? (E.g. 500mA?)

  I intend to buy an external USB drive requiring 1000mA of power USB to work.

  Kind regards.
  Wajid

  UK.

  I remember that USB 1.0 specifications are 150 USB 2.0 and for mAh 500 mAh.
  A laptop usually provides enough power for an external 2.5 "HARD drive, but not for a 3.5" external HARD drive. Disks 3.5 "are equipped with an additional power supply.
  Some USB hubs offer a power outlet in order to increase the maximum current available on each port (i.e. If you connect 2 external HARD drive or a HARD drive on a 2.5 USB1.0 port ")

  Make sure you buy a 'box' that comes with an external power supply or is less with a second USB cable to connect a second USB port available just for more power.

  Remember that external hard drives draw a LOT of energy out of the laptop that runs on batteries... In order to choose the correct POWER option than the second cable.

  BTW, the USB port is protected for current requirements extended... it will just hang your PC, stop, or simply not work at all (you'll notice the disk HARD drives which will be very low on disk).

  I hope I could help

  Concerning

  electroch@in

• Output of the front speaker left is almost a whisper

  Hello

  I had a Pavilion m9300t for over 3 years and I have always used a set of two simple speakers, attached to the headphone output on the front panels until recently when it is installed a system of 5.1 rear speakers using 3 ports on the Panel to find that the release of the "out front" seems to be the reason for all my troubles. I tried to go around the speakers and even checked the speakers on a machine and all seems to work well. "So I thought that all output ports provide stereo output, except the lime' out front speaker" on the rear panel. I have checked the drivers and all settings in Realtek HD Audio Manager and ran the tests of speaker and even used disseminators of media, but the front speaker will provide only a weak sound. Does this mean that his is a hardware problem and if she makes a bad port what are my options?

  Thank you

  MODI

  Hi Modi,

  Is the speaker that branch to the green port 'active '? I mean,'s done it this speaker has its own power supply plug or is connected to other stakeholders who have their own energy source? The green port on the PC is not "powered" so it only will provide a weak signal and expect the speakers to control the overall volume.

  Something else to try, if you unplug all the other actors and simply plug the speakers into the green port, is the change in sound level? Alternatively, if you connect the headphones to the green port, you get audio normal?

  This will help you determine whether or not the hardware works.

  Another thing to try if you don't have it already: when you updated the audio driver, do you have the driver directly from Realtek, or did you use the HP driver? If you haven't tried the latest driver from Realtek, you can do it. Here is a link to download Realtek: http://www.realtek.com.tw/downloads/

  Just select "High Definition Audio Codecs", accept the agreement and then download and install the driver for your operating system.

  I hope this helps. Let us know how it goes.

• Crackling while playing music in the SPECTRUM of the HP 15-4000 Ultrabook

  Crackling while playing music in the SPECTRUM of the HP 15-4000 Ultrabook. TouchSmart with beats audio win 8.1. 64 bit. The problem is gone, when to disconnect the adapter!  Update the audio driver is not the problem. any solution?

  Hi vinnieee, sorry to hear that you are having sound problems with your computer.  I know that the problem you are experiencing is faced with a crackling noise but I'll give you a document that will trouble shoot sound problems.        http://support.HP.com/us-en/document/c03257712

  I also saw that her you said when the power adapter is disconnected from the judgments of the question.  It could be a problem of land, and if that is the question, I would say that contact you HP Total care at 1-800-474-6836 for more in depth troubleshooting.  If it is outside your calling area, please click on the link to select HP in your area.        http://WWW8.HP.com/us/en/contact-HP/WW-contact-us.html

  Thanks in advance

• How to make connections on the outputs of the letter of wsn 3202?

  GOOG morning engineers,

  How to make connections on the outputs of the letter of wsn 3202?

  Sorry, I'm very confused by your response.

  You must not something on the power set by program, just connect a power supply to DIO power and mass of DIO.  Then your DIO lines should be able to output values.

  In addition, I think that you may need to configure the output line.  This would be by the project.  I don't remember what it is, but it should be in some menu properties (probably for the specific line of DIO).

• How to transfer data from the data in table 2D only once file?

  Attached file will write same data in table 4 times 2D file. Output must be in a table 2D.

  Someone will provide a solution or a reason to explain why the data are been ouputted 3 more times? Thank you

  I already told you a better and more effective method. The function of reading worksheet is on the exact same range as your text file and does everything for you. If you insist for some reason strange kernel to reinvent the wheel and write your own code, take the correct path. The use of 4 separate spreadsheet String to Array is the cause of your problem and I already said too much. Don't you think that get you 4 times the data is in correlation with the fact you are using 4 times the functions necessary at all? It is simply not true. Look at the diagram-writing block on a spreadsheet file.

• What gives error of request interrupted on the spectrum screen

  Hi all

  I want to make a screenshot for ESA series Spectrum Analyzer. I make a screenshot, but still not even the current. If and only if I do not use MMEMEL function after reading binary data under vi I screenshot, but not the current one. And if I use the function MMEMEL then I get blank screen capture. And on the screen of the spectrum I always get message that INTERRUPTED the query and error output, I get attention. I don't know what to do these things happened... I'll be very happy if someone help me with this...

  Thanks in advance...

  Pals

  Hi all

  The solution that I was using the wait until I changed to the delay of the watch and I sent * OPC? but don't read do not then it was in error.

  Thanks for any help...

  Pals

• How can I configure analog several outputs at the same voltage

  I need the same voltage to 14 different outputs analog output. The only way I can think of that is shown in the attached image - IE. build a table. With 14 this looks messy - can you imagine how it would look with more! Is there a more orderly way to do this?

  Dave

  Hello

  you want the same voltage setpoint for all channels so u 'initialize the array"give the dimension size you want, I think this will help u