PowerConnect 6248 P do not stack with 12 m cable

Similar Questions

• my printer did not come with all the cables needed to connect to my computer

  I just got a PIXMA ip2820 and he came with all the cables needed to connect to my pc or is it wireliss and if so how I managed to connect wireless

  Hello.

  Our printers do not come with USB cables.  If you do not have a cable connected to a previous printer, you can buy any B USB standard cable locally has to establish the connection.  It is a pretty common cable located at most major retailers office supply or electronics.

  The iP2820 can only be used with a USB connection.  It doesn't have wireless capabilities.

  It has not responded to your question or problem? Find more help contact us.

• BlackBerry smartphones can not synchronize with the USB cable plugged into charge pod

  Hello

  I read on the web site of shopblackberry.com, in the details of charge pod ( http://www.shopblackberry.com/_blackberryaccessories/cgi-bin/pd.cgi?frompage=category&page=product_d... ) that the pod can handset with charger travel or data cable for charge and/or sync with a BlackBerry smartphone. So, my question is related on a problem or a misunderstanding of me to this description.

  I want to know if we could recharge and synchronize the BlackBerry via USB cable or is only responsible for the BlackBerry when connected that way. My second question is, is it possible to synchronize the BlackBerry with the USB cable plugged into the pod or not?

  Because I got a request from one of my users about the fact that his BlackBerry 9000 can not synchronize when it is on his group.

  Thank you very much!

  Hello

  It's a loading dock. It is useful, because just drag you your "BOLD" in there and it will load (just like the 8300 Curve).
  If you want to synchronize, you can plug a usb on the side of the appliance cord. This can be done while the machine is in its dock, where the description.

  I have the same crib, but for the 8300. It's really worth buying. I'm happy with it every day.

• Dell PowerConnect 6248 10 GB ports reference works do not

  Hello

  We have recently installed a module SFP + (part # c107d) in our Dell PowerConnect 6248 switch. The switch does not seem to see the module because before install us the plug-in, it showed a port xg3 xg4, and after the addition of the module, it shows that these ports.

  So I have a few questions:

  Is the SFP + above compatible with this model of switch?

  If so, how can verify us that the ports are active?

  Here is the result of the port details:

  #show interface ethernet 1/xg3 in detail

  Port Type Duplex speed Neg Admin link

  A State

  -----  ------------------------------  ------  -------  ----  -----  -----

  1/xg3 10G - level s/o unknown Auto Up Down

  Port description

  ----  --------------------------------------------------------------------------

  1/xg3

  Flow control: enabled

  Port: 1/xg3

  Belonging to a VLAN: access mode Mode

  Operating parameters:

  PVID: 1

  Capture filtering: enabled

  Acceptable frame type: no label

  Default priority: 0

  GVRP status: Disabled

  Protected: disabled

  -Other - or ITU (q)

  Port 1/xg3 is a member of:

  Rule of VLAN name evacuation Type

  ----    --------------------------------- -----------   --------

  1 by default not marked by default

  Static configuration:

  PVID: 1

  Capture filtering: enabled

  Acceptable frame type: no label

  Port 1/xg3 is configured statically:

  Output name rule of VLAN

  ----    --------------------------------- -----------

  Prohibition of VLAN:

  Name of VLAN

  ----    ---------------------------------

  Port 1/xg3 Enabled

  Status: Disabled role: disabled

  -Other - or ITU (q)

  Identification of the port: 128.51 shipping cost: 0

  Fast port: No. (configured: no) root Protection: No.

  Designated the bridge priority: 32768 address: 80:00:00:25:64:19:92:1 C

  Identification of the designated port: 0.0 cost of access road designated: 0

  Root regional CSE: 80:00:00:25:64:19:92:1 C CSE Port cost: 0

  BPDU: 0 sent, received 0

  Yes, this module is listed as compatible with the switch. It seems that you install in Bay 2? He may have listed these ports but they probably do not appear as active. Have you tried to make a connection with ports?

• PowerConnect 6248 stacking using the front SFP Ports

  I am trying to stack two Dell Powerconnect 6248 switches. Currently they are chained together, but I modules fibre for the front sfp ports. Theoretically, I should be able to stack them. But when I try:

  stack 1/g45 #stack - port console (config-battery)

  Could not set the front panel stacking mode.

  Any ideas? Thank you!

  The PCT6200 requires a stack of modules installed in Bay 1 (XG1 XG2) at the rear of the switch. The stacking module uses CX4/Infiniband type stacking spacers.

  Stacking of front port / user is not supported

• Stacking Module - Dell Powerconnect 6248

  Hello. I have a Dell Powerconnect 6248. This used to be a secondary switch in a stacked configuration (total of 2 switches). However, the captain then descended down we unplugged and it became the master of the battery. It is always configured in a configuration of the battery.

  My question is this: can I remove the stacking module card when the switch is on and in production?

  The reason is that I bought a new 6248 and repaired the old master as well and want to stack these two because they are both on the latest firmware. What is the best practice for this that I don't want to take down the switch by disconnecting the battery module.

  Let me know if you need more information!

  Thank you very much for any information!

  Unfortunately the stackable modules are not hot-swappable. You must turn off the appliance to remove the stacking module.

• more than 2 surfboards 10GbE works do not stack 6248

  Hello

  How set up a battery of PowerConnect 6248 switch with 3 or more 10GbE-commissions only 2 work, weird! Firmware is up to date.

  Two 6248 with 2 10GbE batteries are ok, I was expecting that a stack of 4 with 4 s 10GbE work :-(. Stacking shoud go to 12!

  Quite boring. Any comment?

  
  

• Connection SAN Dell PowerConnect 6248

  Our switch in our network is the Dell PowerConnect 6248. This switch has a SFP module.

  I was wondering if I could use this module to connect my SAN [activeRAID 32 TB of storage active destocking] and have access to the storage as a network or NAS drive Bay.

  To be more precise I'll be plugging the controller [HBA] San to the SFP module on the 624 of Dell PC via a cable Fibre Channel LC.

  I'm new to SAN configuration and look for the best solution to access the storage on my network.

  Everyone has implemented a San with the SFP Module before; If that set up your look like?

  Fibre channel and ethernet/IP are not compatible protocols without another device that can translate. The 6248 has no support for FCoE. There are switches that support both they are called network switches convergent or unified, although generally the traffic is still separated.

• Restart Powerconnect 6248 without disturbing the Configuration

  I apologize in advance for the entry-level position and if that's the answer elsewhere, please point me in the right direction:

  I inherited load on a network LAG / VLAN with a central 2-battery Dell switch Powerconnect 6248 functioning as a main switch and routing of traffic between the VLANs that are shared it resources.

  I want to restart this switch without losing any configuration, because I'm just to enter this network, I don't want to disrupt or rebuild the configuration.

  I can get Telnet or SSH access to the switch but now use the GUI. When I go to reboot I choose to restart the two batteries and am met with the message:

  "The unit will restart with the startup configuration, not the running configuration. Do you want to continue? »

  I had a contractor separate network restart the switch before and I don't know if it simply ignored the message and proceeded. I would like to be able to restart this switch without losing any configuration.

  My question is, I'm ok to move forward through this error message? Or do I need to configure backup to restart? What is the best way to proceed with a simple reboot of two chimneys, while maintaining the current configuration.

  Here is the procedure, I suggest you take.

  -If the running configuration is operational and you want to keep on the switch, and then save it in the startup configuration.

  -before to restart, save the configuration.

  -Keep the battery restart.

  You can then use this backup config as a reference in case something happens to the configuration of the switch. It's a good idea to take the habit of saving after all change config, before the updates of the firmware, reboot, etc.

  Here is an article that will guide you through the commands to perform these actions.

  http://Dell.to/1NPR5aY

  Hope you find it useful.

• Console port (serial) on Powerconnect 6248 switch

  Hi all

  I have two powerconnect 6248 s. The first I've had for several months. The second, I just ordered recently.

  I can't go to the console in to the second switch. I use the same settings (minicom) and cable that I use regularly to connect to the first switch.

  Any thoughts on how to solve this problem? I don't see any startup dialog after resetting the switch 2.

  Thank you

  Looks like you have experienced just about everything that you can. You checked restarted cable, the emulator settings, confirmed working on the other switch, switch, and the default value and it still does not work. It sounds more like it could be a hardware problem with this port. Is the unit still under warranty?

• Where can I submit a PowerConnect 6248 panic?

  Hello

  I just upgraded a PowerConnect 6248 3.3.5.5 at 3.3.7.2 switch and took the panic over the serial console stack trace.

  I've now returned to the 3.3.5.5 and want to submit the stack trace. Email support is not available for me.

  Where should I send it?

  Thank you!

  The support number is 1-800-945-3355

  Please do not hesitate to send it to me, I can take a look.

• Portege R500 - Nokia PC suite does not work with Bluetooth

  Hello

  Toshiba bluetooth + nokia pc suite works DO NOT!

  I have problem with Portege R500. Toshiba Bluetooth stack 6.40 (from the download page) is not compatible with the new Nokia PC suite 7.1.
  PC Suite only works with Toshiba Bluetooth stack, driver version 5.10.12. PC Suite indicates that bluetooth can not be found.

  * See the system requirements for PC suite

  http://Europe.Nokia.com/get-support-and-software/download-software/Nokia-Ovi-Suite/system-requirements

  Where can this 5.10.12 version be downloaded for 64-bit operating system? I just need for the trial which would even work.

  Help, please!

  Hello

  I'm not very well if you want to get an older version of battery BT m.
  On this Toshiba Bluetooth portal, you can get the new version 6.40.00 BT
  http://APS2.toshiba-tro.de/Bluetooth/

  But I don t understand why it should not work with c. 6.40
  I think that Nokia system requirements were created before the release of version 6.40...

  However, if newest PC suite 7.1 is not compatible with the BT 6.4 then I recommend that you test the battery Microsoft Bluetooth...

• V06.10.07.2 (T) Toshiba BT Stack with ActiveSync 4.5 on Windows Mobile 6

  Hello

  I've looked everywhere for the v06.10.07.2 (T) of Toshiba BT Stack with ActiveSync 4.5 on the functioning of Windows Mobile 6. I still didn't find any solution.

  Everything that I found is a tutorial from this site, how to get a Toshiba pc synchronized with active sync 4.2 on a windows mobile 5! Not really useful:)
  As you can see, it differs much, ActiveSync 4.2 to 4.5 and windows mobile 5 or 6

  If there is no tutorial recommend if it still runs on a windows mobile device, that would be a thread of reference for all customers with the same problem, since windows mobile 6 is standard (and soon WinMo 7 version 2009).

  I m having a htc touch cruise Pocket PC with windows mobile 6 and the new Toshiba Bluetooth stack on my pc (win xp sp2 + sp3) installed > v06.10.07.2 (T) Toshiba BT Stack with active sync 4.5.

  Thank you all in advance!
  DAE

  Installation is pretty easy.

  Laptop:
  Set the COM port appropriate in Active Sync that adapts to your COM Server Bluetooth port. It is normally COM7.

  PDA with Windows Mobile 6:
  Ensure COM Bluetooth Manager is on.
  Configure the port on the laptop with Active Sync:
  Start->settings->connections->Bluetooth->devices->add new feature-> select your laptop-> port select "Active Sync"...

• Does not begin with satellite A350 - accident or failure of the motherboard BIOS?

  Hello, first of all, sorry for my English :).

  I have the Toshiba Satellite A350-13 model has and very big trouble with it: when I turn it on by the power button, power light begins to shine, I can hear the voice of the fan for a second - then it stops and I noticed that HARD drive starts to work - I can hear and see by flashing the lamp next to the lamp stack CD player also works, but nothing else happens. There is nothing on the monitor. It seems that the bios is not starting. Let me explain what I do when it all started. My computer worked correctly, but there was a small mess on my HARD drive, then I got the CD recovery system, I realized after buying computer. Everything was ok, the system is working properly, so I started to install my software. I didn't not uninstall this program installed at the factory for system optimization that is (I do not remember his name now, but I mean this program that shows you update for your drivers - I remember that there are updates for the recognition of faces, videos etc..) I installed all the updates that this program presents, including the update of the BIOS. When I've done with the installation of these updates, I noticed that my keyboard does not work - with any button.

  By the time windows has ended it is updated, so I went to "Relight system" in the start menu of windows of the mouse. Then the closed system itself, I saw that windows updates itself as there are always after downloading the updates, but when all this happened at the end and computer must turn off and turn back on, I saw white screen. Computer has not restarted while I was expecting a few minutes. I turned off the computer by holding down the button market / stop and play again. Then, he didn't get up and it's like that for now. What will happen? Is - it caused by the BIOS update I did? Or - is it possible that this motherboard fell down? I think this is connected with the bios, indeed with his absence :) But when I switch on the computer, the keyboard still does not - I can see it, because the green light should appear on the CAPS LOCK button when I hit him if there is a power, even if the bios does not work. Am I wrong? Is there any possible to return BIOS configuration of fabric? I'm quite confused, because I have that for two months - it is like new. I'm excluding the dysfunction of the monitor.

  I hope any of you had a problem like this and there is a possible solution for it. My computer is always guaranteed.

  > My computer is always guaranteed.
  That of the point! Please contact nearest Toshiba authorized maintainer and leave check your laptop.
  There is serious hardware problem, and I don't think you can do something.

• Chart stacked with cursors that extends to all parcels

  I use LabView 2009 9.0f3 (32-bit)... I want to create a chart stacked with two sliders that extends to all plots. I can only find the graphic stacked option but not graphic, and I don't know how to create cursors that spans all of the plots. Attach a picture that my college created showing what I want to achieve.

  Thank you

  You can create a table of locations (remember to group, place them in a cluster first!).

  Because the properties are identical to the elements of the array, the positions of the cursor will be the same for all the graphs, whichever one you are moving.