PowerConnect 7000 series in-band versus out-of-band management

Similar Questions

• Is location 11 Pro 7000 series wide band Mobile compatible with Telstra 4 G Dell

  I am wanting to buy 10 of the CAL0437140AU - Dell place 11 Pro series 7000 tablets which includes wireless 4G LTE Mobile Broadband Card GEN 5810e Dell.

  This unit is compatible with the 4 G Telstra network

  You will need to check with the Dell Australia for this response. This is the US forum.

  http://www.Dell.com/support/contents/au/en/audhs1/category/contact-information/technical-support

• Over 4500 X out-of-band management interface

  Each of the X 4500 switches in our stack has an interface of Fa1 beside the console port series.  My understanding is that this should be used for the out-of-band management of the switch.  Here is the configuration of the interface:

  interface FastEthernet1

  VRF forwarding mgmtVrf

  IP 172.21.2.30 255.255.255.0

  automatic speed

  automatic duplex

  end

  Samba configuration was by default.  The only thing that I changed was the ip address information.  My question relates to things like domain-lookup and GANYMEDE.  I can't use this interface for these functions.  Even if I add the following global configuration to my passage:

  IP domain-lookup-interface source Fa1

  Radius-server interface Fa1 source IP

  the switch is unable to communicate with the reference of DNS servers by ip name-server command or the reference GANYMEDE + servers in the section profile of the RADIUS server.

  In the case of GANYMEDE, the following debug output is produced when I try to open a session using GANYMEDE:

  * 10:24:58.874 29 August: MORE: Queuing AAA request 38 for processing authentication

  * 10:24:58.874 29 August: MORE: treatment demand beginning 38 authentication id

  * 10:24:58.874 29 August: MORE: authentication start package created for 38 (sdavidso)

  * 10:24:58.874 29 August: MORE: using the 172.19.40.31 Server

  * 10:24:58.874 29 August: HIGHER (00000026) / 0: road to connect error no. to host

  * 10:24:58.874 29 August: MORE: choose the next server 172.19.40.32

  * 10:24:58.874 29 August: HIGHER (00000026) / 0: road to connect error no. to host

  * 10:25:05.539 29 August: MORE: Queuing AAA request 38 for processing authentication

  * 10:25:05.539 29 August: MORE: treatment demand beginning 38 authentication id

  * 10:25:05.539 29 August: MORE: authentication start package created for 38 (sdavidso)

  * 10:25:05.539 29 August: MORE: using the 172.19.40.31 Server

  * 10:25:05.539 29 August: HIGHER (00000026) / 0: road to connect error no. to host

  * 10:25:05.539 29 August: MORE: choose the next server 172.19.40.32

  * 10:25:05.539 29 August: HIGHER (00000026) / 0: road to connect error no. to host

  This output shows that I can ping from RADIUS servers:

  HQ-4500 X - SW1 #ping vrf mgmtVrf 172.19.40.31

  Type to abort escape sequence.

  Send 5, echoes ICMP 100 bytes to 172.19.40.31, wait time is 2 seconds:

  !!!!!

  Success rate is 100 per cent (5/5), round-trip min/avg/max = 1/1/4 ms

  HQ-4500 X - SW1 #ping vrf mgmtVrf 172.19.40.32

  Type to abort escape sequence.

  Send 5, echoes ICMP 100 bytes to 172.19.40.32, wait time is 2 seconds:

  !!!!!

  The Fa1 interface cannot be used for these types of functions deliberate or is there something I can do to make this work for my setup?

  Thank you

  Steven

  Given that you can reach the remote RADIUS server, I suppose that you have created a default route for the mgmtVrf:

  IP route 0.0.0.0 0.0.0.0. VRF mgmtVrf

  The other bits you need to address is in mode config-sg-Ganymede:

  IP vrf forwarding mgmtVrf

• software for Toshiba DVD and the Windows Version 7000 series

  I found a file that contains the information that I need help.

  In c:\I386\Comdata\Toshdvd
  The software for Toshiba 7000 series DVD player is not compatible with ths version of Microsoft Windows and will be disabled during the upgrade. You must uninstall the software for a more complete solution

  I don't know if this is the problem with my DVD/CD drive. The light comes on and it runs for a while when she has a DVD inside, but is not listed by the DEVICE MANAGER. I use Windows XP

  Could someone help please?

  Just in case anyone else experiencing similar problems, in that I found some information

  http://209.167.114.38/support/TechSupport/TSBs/all/-TSB000917.htm

• volume control stuck on screen - not work - not adjustable, Inspiron 13 7000 series 2-in-1

  I have just bought a new laptop Inspiron 13 7000 series 2-1. It comes with Windows 8.1. It happened (don't know why) that the volume control is frozen on the screen at the top left with the volume level of 0% so I can not adjust the volume of all on both the keyboard and the touchscreen.

  What I've tried is less than

  -In the Control Panel, sounds, communications: when Windows detects communications activity

  Select "do nothing".

  -uninstalled the audio driver and leave it is reinstalled automatically after reboot

  -uninstalled the audio driver and install the audio driver downloaded from dell support

  -clean the boot and uninstall - reinstall the driver

  It was solved once when I tried the pull-off and push the usb for the logitech wireless mouse. When the volume control is stuck on the screen again, I tried this again, but it does not help.

  Any suggestion please. Thank you.

  NUCH

  Thank you!  Has exactly the same problem today.  Here is a picture of the cable and screw in question.

  

• (Redirected) Why my touchpad disable? 15 Inspiron 7000 series 7559

  Hello, I just got the Inspiron 15 7000 series 7559 i7 processor Windows 10. It's my first Dell and I like it so far. However, I can't disable the touchpad. I went into the settings and turned away but its not going off. I use a USB mouse or the touch screen, so I need to disable the touchpad because it makes very frustrating to type. Whenever I start typing it will all other the place because my hand or thumb press. Any suggestions?

  As you have a laptop, better make this laptop in the computer Forum post here:

  http://en.community.Dell.com/support-forums/laptop/default.aspx

  Bev.

• Latitue 7000 Series 12 (E7250) - maximum SD card capacity

  What is the SD card maximum capacity Latitude 12 (12.5 ") (E7250) 7000 series laptop?

  You can buy too large a card you want. The computer does not limit, fact that the size of the map.

  If you need a better way to store, have you considered an external hard drive?

• (Redirected) Dell Inspiron 17 7000 series stops at random!

  I have a Dell Inspiron 17 7000 series. It stops randomly without obvious reason. What can I do to stop this?

  As you have a laptop, better make this laptop in the computer Forum post here:

  http://en.community.Dell.com/support-forums/laptop/default.aspx

  Bev.

• PowerConnect 6200 series interoperability with 3Com Switch 5500.

  Hi all

  We offer to our customer Dell PowerConnect 6224 and 6248 as they are expanding their network.

  Their existing network is 3Com Switch 5500 and the main switch is 5500G - EI. Of course, on their network, they have mutiple VLAN and switch 5500G - EI core will make the VIRTUAL LAN routing.

  I would like to know, is it questions about interoperability between 3Com Switch 5500 and Dell PowerConnect 6200 Series, especially on the VLAN routing?

  Know your opinion.

  Thank you and best regards,

  Syed.

  I'm not aware of any questions that you would see with the use of these switches together. On switches 62xx you set them VLAN, and then set the connection of 3Com in general or Trunk mode, allowing the VLANS on the connection.

  Create a VLAN

  Console (config) # vlan database

  VLAN console(config-VLAN) # 2

  VLAN console(config-VLAN) # 3

  VLAN console(config-VLAN) # 4

  output console(config-VLAN) #.

  Configure the interface in Trunk mode and allow for VLAN through it.

  console switchport mode trunk #.

  console # permit trunk switchport vlan add 2,3,4 tag

  You may need to set a static route on the 62xx switch so the traffic on the next hop.

  Console (config) # ip route 172.16.0.0 255.255.0.0 10.0.0.2

  Here are a few good white papers to look over. Not all of them concern the 62xx switch, but the information is always good.

  www.Dell.com/.../app_note_38.pdf

  www.Dell.com/.../app_note_2.pdf

  www.Dell.com/.../pwcnt_link_aggregation.pdf

  www.Dell.com/.../pwcnt_VLAN_interoperability.pdf

  www.Dell.com/.../app_note_4.pdf

  Thank you.

• FirePOWER vs 7000 Series Appliances Cisco Cisco FirePOWER 5000 Series Appliances and Security more

  Good evening

  I put this thread to better understand that we enter firepower vs FirePOWER 5000 Cisco Cisco 7000 series devices Series Appliances are stronger for AMP, IPS and URL protection.

  It is accurate to say that Cisco FirePOWER 7000 series devices is more powerful and safer such as defence AMP IPS and url vs Cisco Appliances of series 5000 firepower?

  about security Plus (a feature of the router ASA5506H-SP-BUN-K8) whose security it provides?

  have a good answer

  8000 and 7000 series devices are devices that came with the acquisition of Sourcefire. Strictly, they perform the Sourcefire software only and do not have the features of the ASA (routing, AnyConnect VPN and many others). They usually also provide larger flow capacities during execution of all services of firepower (IPS, AMP, AVC and characteristics of the URL). So if you don't need all the features ASA then the 7000/8000 series devices is probably a better choice.

  The ASA5500-X series includes the best of both worlds. The ASA and Sourcefire software are running on the same box. So you can still use all of the functionality of the SAA and then also re - direct specific traffic to the Sourcefire module for additional inspection.

  I hope this helps!

  Thank you for evaluating useful messages!

• Shape gradient develops series of banded paste forms

  The last two days, I noticed an annoying problem with my gradients shapes in Illustrator. Sometimes, when I copy a shape to a document and paste it into another, the gradient develops into a series of banded forms that are masked by the original form. What is going on? Is this a bug?

  Uncheck "enable clipboard history" in the preferences of the launch bar suits, so it is not necessary to stop completely from Quick Launch bar.

• Dell Inspiron 15 7000 series WiFi question

  I bought an Inspiron 15 7000 series a week ago. Early on, the wifi does not work properly. It takes too much time to connect and also automatically disconnects frequently. Sometimes it shows only limited connectivity. I've updated the drivers but no change so far. All other devices in the House do not work properly. Thanks in advance for your support.

  10 days ago, I bought an Inspiron 15 7000 series.  I had similar problems.  WiFi worked when you're sitting next to the router, but it refused to connect at all in low signal strength areas.  In moderate zones (next room or room just below) it works very well for a while but intermittently lose connectivity and although showing that connected would refuse to transfer anything - this necessary apparently the router rebooted to solve.  Since this morning I seem to have fixed things.  It is now usable in any home, linking where it has not before and no abandonment so far in areas of moderate signal strength.  The solution for me was to download the drivers from Intel.  Note that it worked when I first completely deleted existing drivers for wi - fi and bluetooth using Device Manager - I needed to check the box to delete the files, not only remove the drivers.  Then run the downloaded Update resulted in different drivers being installed.  In fact, these seem to be older than those previously installed - version number lower, earlier, fewer config options - which may be why the update did not return to this version until I completely deleted the drivers existing. It worked for me.  Certainly worth a try if you a not entirely remove the existing driver before the update files.  Note that if you do this, you must replenish your router password when you first connect to the wi - fi again.

• Inspiron 15 7000 series 7559 - controller USB Win 7

  Dear all,

  I'm a process engineer. Currently working abroad. During my trip abroad, my old laptop Inspiron 15 5000 failed on me. I immediately got a replacement Inspiron 15 7000 Series 7559.

  I have restored my backup image and try to install the drivers. My OS is win7. However, I have a problem to find the right driver for (USB) Universal Serial Bus controller

  Now all my port USB does not work. Could someone help me please? Thank so so much

  I need to install windows 7, as most of my software does not support the latest OS

  Hi, xigtec31!

  The solution for install: USB 3.0 Driver: Intel USB 3.0 eXtensible Host Controller

  (I use only)

• UCS FI6248-of-band management

  Hello

  We currently manage our FI6248s CLI and UCS via out-of-band management interfaces on did them. Does anyone know if the FI6248s can be managed internally on 1/10GBe connections?

  Thank you

  Hello

  This feature is currently not avaiable for the FIs of UCS.

  You must continue to use the management ports either the mgmt0 OOB only.

  Afonso

• Question of Linksys LAPAC1750PRO band management

  Hey everybody. I have installed two AC1750PRO APs for a customer. Setup was easy, I upgraded 1.0.6 Build 2, and they appear to be stable. ButI have a question about the option management on this unit group.

  I understand other devices and documents that band leadership tries to force about 70 ~ % of devices that support dual-band on Channel 5 instead of 2.4 GHz, to reduce congestion, as most of the devices simply default dual-band 2.4 otherwise channel.

  I'm not sure, this is how the Linksys 1750PRO behave with this setting? The only option that I see because it is in the menu Access Point virtual under radio 2.4 ghz, in the form of a or to disable the check box. Am I was right in my assumption that check this checkbox will result in customers dual band facing the 5 GHz channel, instead of the channels 2.4 ghz, if possible?

  In my view, that documentation should be updated in what respect this setting and how it behaves. The FAQ on this devices has only a question about tape management, which is 'How to activate steering band?' and the answer is incorrect. The answer says that you go to Configuration > Wireless > advanced. But there is no section advanced 1.0.6. The setting is indeed on the menu of virtual Access Points (VAP) under only 2.4 ghz radio.

  Yes, the documentation on the direction Strip is not the best.

  You are right about what direction Strip is and does.

  What I find weird, it's that you can activate Executive on 5 GHz. It's not logical in my thinking because the direction of tape effects only Dual Band customers who are connecting to 2.4 Ghz.

  It seems to me that dual band rules are not strictly implemented in the user interface. I recommend that you test with the underside of configuration for the direction of the band.

  1. Radio 1 (2,4 Ghz) VAP 0 activate direction Strip
  2. Radio 2 (5 GHz) VAP 0 enable band management and reflect the Radio 1 PPV parameters 0

  In my mind, this is the only setting where I can see band Director for VFR operation 0.