Presario cq70 116ea, refuses to connect to new wifi router unless the router's security mode.

Similar Questions

• New wifi router installed. Why do connect to sites but lose the connection as I browse even though Windows said excellent signal. To deactivate/activate

  New wifi router installed. Because then I can usually connect sites OK but when getting around a site or to another, I lose connection even though Windows said signal is excellent. Toggle heals the problem temporarily. Two tablets under the same roof using wifi even have no problem. There is no consistency in when the problem arises in any session. It happens in Firefox and Thunderbird. Close and restart the program does not help.

  I tried the reset and it was not good. Then I learned that my wife had a similar problem with his ipad I did what I should have done at the beginning, I restarted the router again. Hey presto, problem solved.

  Now, I'm off to eat some humble pie. Thank you, guigs2

• My printer is connected to my WiFi router, but I can't print

  My printer is connected to my WiFi router, but I can't print.  When I ask to print something, it goes through the options but nothing prints or is pending.  Any ideas?  Low ink, would result even if I printed a test page and newwork connedtion.

  Hello

  1 are there any changes or updates made on the computer?

  2 Windows operating system is installed on the computer?

  3. do you get an error message? If Yes, what is the full and exact error message?

  4. What is the serial number and model of the printer?

  I also suggest send you the link and try to run repair and check.

  Problems printing and printing errors

  http://support.Microsoft.com/mats/printing_problems/

  I suggest to see the link and try to run the troubleshooter.

  Printer in Windows problems

  http://Windows.Microsoft.com/en-us/Windows/help/printer-problems-in-Windows

  Let us know if it helps.

• Computer Vista laptop cannot connect to new wireless router

  I had the laptop for about a year and a half, and he has a history of being pretty skittish about the wireless connection.  Often he simply refuses to do so.  During vacation last year, for example, the other three laptops connected family easily to wi - fi hotel, but mine has refused to.  There are a lot of other moments when the laptop could not connect, but I was able to connect to two most important places - home and work - without much trouble, and so I haven't looked too hard to solve the problems of connection up to now.

  This week, I replaced the router in my original configuration.  The old Netgear router kept giving up the connection between her and my ISP.  The new Linksys router looks rock solid in this regard.  I have a desktop running XP computer that is wired to the new router Linksys, and he sees the internet very well.  My laptop Vista unable to connect (wireless), however.  He sees the network with a lot of intensity of the signal, and it tries to connect.  I get a message saying that the connection takes longer than usual, and then another message saying 'connected.'  However, I do not have internet access, and I see other devices (just the XP desktop, really) on the network.  The Network and Sharing Center shows my laptop connected to the 'unidentified network', and then there is a red X between this network and the Internet (represented by a grey globe).  Laptop computer signals its 'access' as "local only".

  From the desktop, I can access the internet, so the router is connected to the points upstream.  From the desktop, I can also access the router configuration pages, and I see that it does not list the laptop as a dhcp client, even if the laptop thinks that it is connected.

  ipconfig on laptop computer displays a wacky IPv4 address: 169.254.2.91 and I guess that the laptop does not get an address passed to the router.  I think that there should be a 192.168. *. * address if it worked properly.

  Now, I was pretty sure my laptop's wireless adapter to work properly.  It always connects to the old router and it always connects to the work.  But to be sure and really test the new router, I went out and bought another USB adapter wireless.  When I plug it into the computer to Office XP, the Office connects to the router and can see the internet (even with the connection cable is disconnected).  So the new router and the new wireless USB adapater properly.  When I plug the USB wireless adapter into the laptop, the laptop still can't connect and still not get a good ip address assigned by the router.

  I've been at this for a few days now, and I could really use some help.  I read a few items in the Microsoft forums that was supposed to fix the problem.  One of them told me to try to start a program called DHCP in the Administrative Tools folder.  I do not have this program on my computer.  Another told me manually change my registry (ouch!) and add a new DWORD value, and set its value to 1.  I did, but it did not fix the problem.

  I would be very grateful for any help.

  Jim

  Alright.  I am home to work and back again.  I have read several posts with people reporting problems similar to mine, so I guess I'm not alone in this.  In a thread, the experts proposed to start in Mode safe mode with networking.  So I gave that a shot.  I still couldn't really connect - just this 'local only' without an assigned IP address.

  One thing I did notice, is that my laptop brand and its wireless adapter seem to get a special mention in most positions.  I have a HP Compaq Presario CQ50 Notebook PC running Vista Home Premium SP2, 32-bit version (even if the processor is 64-bit).  The wireless adapter is an Atheros AR5007.  Several other people with this card have reported problems.  Maybe it's the cause?

  I look into updating the driver for the card, even if yesterday's test with the separate USB wireless adapter showed that the problem could not just be limited to the Atheros card.  To search for a driver update, I connect my laptop to the router with an ethernet cable.  It's nice to see the web on your laptop.  No update driver does.

  For fun, I try to establish a wireless connection with the router, while the wired connection is still in place.  Looks like maybe it worked?  I say a little prayer and unplug the ethernet cable...

  It's a miracle!  I have a wireless connection to the router and beyond, to the internet.  Huzzah!

  The network has a real name, too, instead of just 'unidentified network '.  I want to change the network type from the public to the private, which I was unable to do while he was still 'unidentified '.

  Can I terminate the connection so that I can see what happens when I try to reconnect.

  Another miracle!  It connects to and still see the internet.  Callooh!  Colay!

  Next test: see what happens after a reboot... (please, please, please)...

  Ch-ching!  It works again!

  Final (?) test: reinstall the McAffee internet security suite and restart.

  And it still works.

  Here's a recap of what I found:
  1. laptop could not connect wireless router again, despite dozens of attempts in which I get every available straw
  2. laptop computer could see the internet when connected to the router
  3. laptop could connect wirelessly to the router while the wired connection is in place
  4. Once this first wireless, laptop computer was able to connect to the router even when the wired connection has been removed and the computer restarts

  I would describe my discovery above as a work-around rather than as a solution, however.  It does not always help me stay connected the next time I'm on vacation, for example.  But perhaps the information I provided can help experts to diagnose the real problem a little.

  I look forward to hear something back.

  Jim

• Phone will now connect only via wifi to otherwise the web network does not work

  My Motorola xprt is less than 1 week old. At first, that everything worked well. I got internet connection etc. So I connected to my wifi at home and it worked fine, then my wifi secure at work. but now I can't connect to the internet without wifi. There is no 3G signal activity. I tried to help out with a representatitve of Sprint and after trying to make an update to profile 3 times in vain, he recommended I take it into a store and maybe get a new phone. Prior to this, however I tried to solve the problems of the site via a USB connection with the drivers properly installed (I think) and he was not able to detect my camera. Don't I have some settings wrong? I'm going crazy because I like the phone but can not use wifi all the time.

  In fact the question on the data connection helped because I went to my settings and the title of the data management 'enabled data' has not been verified, now everything is ok - I have my 3G back. It seems that the Sprint guy should have just over my settings rather than suggesting that I might need a new phone. Thanks again.

  I have another question, but I'll start a separate discussion.

• TC drops with new wifi router

  Hello

  I recently changed the wifi set up in my house when I got a new router/modem Comcast wireless.

  my equipment:

  -The new series of wireless router/modem Arris TG862G bridged mode

  TC - 4th gen (2 TB) running 7.6.4

  The TC is connect to Arris via Ethernet. The TC also has a feature of AT & T MCell and Powerline wired extension that goes to the basement. The TC is on the second floor.

  When I put this in place, I renamed my network, comments and TC names digital alpha shorter and passwords changed to the alphanumeric passwords only on the advice of this forum. In addition, the network connects to multiple IOS devices, Windows Mobile, smart TVs, etc., all running newer versions of IOS.

  That is the problem.  The new configuration often removes the wifi so that no camera can detect the network. By frequently, I hear once every few hours.  This was solved by rebooting the system.

  So far, I tried switching routers so Arris is router and TC is the bridge, but same thing happens.  Curiously, I even reinstalled old no wifi modem to test but still had the same problem. This facility has been very reliable before the new name, but hard to believe that a name change is the cause.

  I welcome suggestions.

  Sorry we're a little slow on your problem.

  The new configuration often removes the wifi so that no camera can detect the network. By frequently, I hear once every few hours.  This was solved by rebooting the system.

  What happens if you simply restart the TC?

  So far, I tried switching routers so Arris is router and TC is the bridge, but same thing happens.  Curiously, I even reinstalled old no wifi modem to test but still had the same problem. This facility has been very reliable before the new name, but hard to believe that a name change is the cause.

  Name changes will not cause sudden dropouts wireless... It's the change of network and a router that does not get along with the TC. Apple routers can be hard enough.

  I would go back to the installation with the Arris as the main router... and TC in bridge.

  Once you have this configuration, change the connection of the arris to TB... Ethernet that was in the TC wan port... Move it to LAN port.

  We are seeing problems with the side WAN.

  Unless it's just age... The change of network may do strange things... and the TC Gen4 has a lack of reliability when it reaches the end of life. A number of them die completely and others have network problems... either the wireless or ethernet side... It can simply wear... (of course it of components such as power supplies and cause capacitors which are at the origin of these issues). Fixing the level of the Board of Directors is a thing of the past... the cost effectiveness of the modern manufacturer has deleted as viable repair. With the exception of a few weird things I can fix it... It is usually not worth.

  The summary of what you need a new TC or a new management mode of backups.

  Happy to work through the questions...

  If the TC wireless is stall... do you mean no signal... or no internet connection...

  The next time he falls... from a client on the TC main router ping or ping another client in the terminal and tell me if any of this signal or what is lost.

• E2700 cannot connect directly to the modem, but connects via another wifi router?

  I have a Netgear WNDR3700v2 that I was very pleased until I had a nest of thermostat. Apparently it's a router not supported and I had to change it. I bought an E2700 since he took charge, but I have a huge dilemma...

  If I connect the linksys directly to the modem, I don't get an internet connection. I got out and renewed IPs without success...

  But if I wired the linksys for the netgear, I get a good solid internet connection. problem is, I have no need for installation of 2 routers on top of each other...

  any suggestions? I would like to know what kind of information you need.

  Basically, I do not understand why he is not able to connect directly to the modem to linksys. Yet, it becomes solid connection wired through another router.

  I use Comcast and South FL. it is motorola surfboard modem

  OK, found the solution.

  call 1800COMCAST

  go to the problems of the internet, there is an option to send a refresh signal to your modem.

  I did, and it started working. I guess that clears the memory and binds to the new MAC address...

  After that I did, internet is back. I hope this will be useful to someone. I was ready to return the dang thing.

• Whenever I connect to F/book, I get the following text: 'Security warning' - you asked an encrypted page that contains unencrypted information. The information you enter on this page cold easily or you see be prepared by a third party".

  My e-mail is: [email protected].
  Whenever I connect to F/book, I get the following:
  Security WARNING: you have requested an encrypted page that contains unencrypted information. Information you see or enter on this page could easily be prepared by a third party."

  
  

• I can not connect to smart wifi router outside of the House?

  Hey.

  I need to portforward port for logging in my smart wifi router Linksys EA6500 from the House to the outside? I can only connect when I am om LAN or wifi...

  Another question: I can only connect to the same router using an application? Is there a way to connect via a browser?

  THX.

  When you have created an account for your WiFi Smart router, have you received a confirmation e-mail? Check your email and you must confirm it so that you will be able to use it. Refer to this link ofr more information: http://www6.nohold.net/Cisco2/ukp.aspx?vw=1&docid=12e0e8fa76f340739d0cb72037819ca9_Creating__activat...

• Time for a new wireless router? Security no longer works

  My router has acted lately.  I did the Web page and two manual reset / original restore.

  I works very well without any security.  When I reset the password name & network security everything seemed normal.

  It now displays the new network name but should not be the new password, it appears immediately as "invalid security phrase.

  On the router to the wireless security, I have selected WEP, 128-bit, 26 hexagonal etc., entered my password, press on generate and then 'save settings '.

  Everything seems fine, but it does not accept the new password.  Again, this works fine without warranty, but I can't run like that.

  Can anyone help?

  Thank you!

  Time for a new wireless router and new wireless adapters that support WPA2 Personal wireless security. IMO

• Satellite L850-18 t has problems to connect to new wireless router

  Hello

  I have a serious question that, at the present time, he cannot know. Basically 2 days ago I bought a new router because the other more old has stopped working. And I bought Tenda router. Since that day I have problems connecting with my Toshiba Satellite L850-18 t - I have never had similar problems before.

  I put the security of the router for wpa - psk with aes encriptación mode option. The laptop connected and worked fine, but the next day, he has not suddenly connect more. So I went to check the option, everything was allright. Troubleshooting gave me the following error: "problem with wireless adapter or access point. I tried to reboot wlan driver, but nothing happened. The only thing that seems to help is to change the security WPA2-PSK mode (or vice versa), restart my laptop and it connects then.

  Anyone have some clue what happens? It must be something with my laptop settings, because all other devices (another computer toshiba laptop but older, a PC and android devices) work perfectly.

  Among the specifics on laptop:
  -Computer laptop Toshiba Satellite L850-18 t
  -Network cards:
  -AR9485WB-EG atheros wireless network adapter
  -Realtek PCIe GBE Family Controller
  -Router: Tenda

  Thank you!

  Posted by luka_10
  

  Hello

  I have a serious question that, at the present time, he cannot know. Basically 2 days ago I bought a new router because the other more old has stopped working. And I bought Tenda router. Since that day I have problems connecting with my Toshiba Satellite L850-18 t - I have never had similar problems before.

  I put the security of the router for wpa - psk with aes encriptación mode option. The laptop connected and worked fine, but the next day, he has not suddenly connect more. So I went to check the option, everything was allright. Troubleshooting gave me the following error: "problem with wireless adapter or access point. I tried to reboot wlan driver, but nothing happened. The only thing that seems to help is to change the security WPA2-PSK mode (or vice versa), restart my laptop and it connects then.

  Anyone have some clue what happens? It must be something with my laptop settings, because all other devices (another computer toshiba laptop but older, a PC and android devices) work perfectly.

  Among the specifics on laptop:
  -Computer laptop Toshiba Satellite L850-18 t
  -Network cards:
  -AR9485WB-EG atheros wireless network adapter
  -Realtek PCIe GBE Family Controller
  -Router: Tenda

  Thank you!

  What I see is that we have same wireless Chipset, Tenda use Ralink or Broadcom chipsets, which are compatible with our wifi cards, then I would tell you my opinion do 1st updated drivers on your laptop, I use the latest x 64 win10, atheros version drivers 10.0.0.326, then go and upgrade your routers firmware! I don't know it will solve your problem, by the way check firmware of the laptop is the last 6,80 I think!

• Cannot set my Intel 4965agn card to connect to new N Router

  X61T

  Vista Business 32-bit

  With the help of Windows for

  All,

  I have been using G wireless since the purchase of my X61t in August 2008. Finally stepped up to N in my house. (LinkSys WRT310N) MacBook woman has seen and connected without the need to change anything. X61T, however, says he sees the router, but that "the settings saved on this computer for the network do not match the edge of the network. (Mac 1, Windows 0)

  When I roll over the name of the SSID it correctly pointed out that this is an 802.11n signal.

  I looked at the properties of the card wireless in Device Manager and it lists 802.11n Mode as 'active '. The channel width is 'Auto '. I tried the router with 20 and 40... now set at 40. There is a parameter which is confusing to see: the last item is labeled "Wireless Mode" and allows 6 settings with various arrangements of the interface possible wireless standards: 802. 11A, 802. 11 b, etc., all the way to 802.11a/b/g' - but no mention of N in this section. I don't see any other setting that I recognize as related to the connection. Do a search here on this Board and acroos the forums all came with a few bugs I've tried: go into the BIOS and disable wireless then enable, for example.

  Diagnostic tool from Intel PROSet / Wireless works fine until it gets to the Association Test and does not say, "not linked".

  Although the router is set to broadcast a windows diagnosis indicates that the network is hidden. Weird.

  Because the other computer is fortunately I agree with windows that the problem lies in the configuration of the Intel card. 61 x sees the internet via a cable - no problem!

  Thanks in advance for your suggestions!

  Jonathan7007

  Hawaii

  Suriya, thank you! You are a consistent help to people here on the forum.

  I have "fixed" the connection - but who put in quotes because I don't know what I did to make it work. I think that these were settings of the router automatically changed by a firmware update I did as part of troubleshooting. Perhaps those (or more exactly do not keep Super-une attention on the order of the changes and related measures) assigned to my sense of what "worked".

  I was about to update this driver to a version of June 2010. I bet that's the link you provided... I found that... but I let the drive where it is until everything else works computer here. Not broken don't fix it...

  Sheesh. These devices of productivity, right?

  Now, I hope that the flavor of "N" is really faster.

  Once again, thank you.

  Jonathan

  Hawaii

• Firefox keeps refusing to connect to websites, I visited many times and are secure, I press 'allow' sometimes it does, sometimes it doesn't work, what should I do?

  Firefox has recently begun claiming in a black bar at the top

  "firefox prevented this page automatically redirecting to another page" allow

  Sometimes when I press 'allow' it does, sometimes even on sites, I used several times in the past a lot and know they are secure, such as my Uni Library account, it just comes back with the same bar.

  Can someone help me get rid of it? preference for good! It of just slow me down and is infuriating. Also, my account of energy "Scottish Power", has just opened in Safari, as firefox just log on seconds, Scottish Power themselves told me to use Safari instead and that works fine, but I'm used to firefox and prefer to keep, it is becoming more and more difficult to use, WHY?

  Took the screenshot and was expecting a box of 'Browse', but not so impossible to download photo either. When I tried to install the troubleshooting recommended below, firefox will allow him as not secure! Is it not a little on top when he thinks his own site not secure? what the hell is happening?

  This feature can be disabled:

  1. Go to the Firefox options
  2. Go to the Advanced tab
  3. Select the general section
  4. Uncheck the warn sites when they try to redirect...
  5. Click Ok

  The report please come back shortly.

• HELP-Compaq Presario CQ70 - new drive hard = Nothing

  Hi all, computer dummy here and I need help.

  the Seagate Momentus 250 gb 5,400 RPM hard drive failed completely on my Compaq Presario CQ70.

  I bought a new Seagate Momentus 500 gb 7,200 RPM.

  I had Windows Vista installed on my laptop.

  but when I'm the new hard drive, I tried to install Windows XP (that I don't have a Vista disc).

  in any case, I inserted the new drive hard and drive XP OS then - NOTHING.

  just black screen and after a while, blue screen saying windows has been closed.

  When I go into the BIOS I do not see the hard drive and everything, but I can run a hard drive test and it passes.

  I have removed and reinserted the hard drive and run the XP OS several times but still the same.

  did anyone can help this old man so I can get my laptop up and working again.

  Recognizing.

  Andrew

  Hello again, Paul and once again thank you.

  I have a Windows Home Premium OEM installation disc.

  I wanted to wait get your response re Home Premium before I considered a set of recovery discs using the info you provided :-)

  I'll try to install Home Premium if that does not work then I get a set of recovery disks.

  Kind regards

  Andrew

• Problem with cooling - HP Compaq Presario CQ70-211EM

  Hi, I didn't really know where to post, so I decided to post here, sorry if this is the wrong place.

  So, I have this laptop (HP Compaq Presario CQ70-211EM) for 3 years now, everything works fine, except the system cooling, computer laptop everything gets REALLY hot, after have 10 (!) minutes, I still have it, throughout the day, he is standing on a special base, fan has been cleaned (by me) 2 months ago. The areas that become really hot are: hard drive, ram, area around the fan and the left side of the laptop.

  I don't know what to do, any ideas? I really need help

  Additional information:

  Windows 7 Ultimate x 86(32bit), 160 GB of HDD, 2 GB RAM, fan, always, always connected (the battery is dead).

  ~ Viper13

  You can also remove the battery since you mention that he died anyway. Sometimes removing aid to cooling. When you set the bass processor speed - you changed it under 'Sector' haven't you?

  Yes, remove the old compound with alcohol. You can get Arctic Silver 5 here or in of many stores, Radio Shack, Best Buy, Staples, etc. Below are videos showing application of Arctic Silver and ceramics, the two coupons.

  http://youtu.be/MNJ-fUNgRs8

  http://youtu.be/hdHMsDXpvew

  http://youtu.be/A_C0RkpO7LU