Printer M1536DNF

Similar Questions

• HP laserjet pro M1536dnf wireless configuration in order to use Air printing

  Since I am trying to print from my new Ipad Air, excuse my newbie questions for networking printing!

  What I know so far:

  1. I understand my printer HP laserjet pro M1536dnf is 'not' a WiFi printer.

  2 by HP support and Apple Support web sites, my printer HP laserjet pro M1536dnf is 'Air Print' active. I guess that a certain update must incorporated the Betacam Air Print!

  3. According to the web site of the HP Support, I have currently the latest firmware installed (20130815).

  Note: On my Config report, it shows the status for IPv4 and IPv6 as "network cable unplugged". I have the address IP Show as active.

  3. my home configuration has the internet cable from my modem cable to my router wireless Linkys E3200 via a coaxial cable. Between my router and my computer is connected through the Ethernet cable. My printer HP Laserjet 1536dnf printer is connected to my computer via a USB cable.

  Issues related to the:

  1. go to after I saw and read about on-line, is correct to say "I'll have to change my Ethernet cable from the router to the computer and change it to leave the router to the Ethernet port on the printer?"

  2. do I have to remove the USB from the printer to the computer?

  3. by removing the USB cable between the printer and the computer, how my computer would communicate to the printer to perform a print job? Unless, I suppose, I add another Ethernet cable between the router and the ethernet port on my computer!

  4 other advice, I might have missed?

  @RicharddR

  Thanks for your post on the forums of hp.com. Here are answers to your specific questions:

  1. you must have all your devices on the same cable modem network: computer, printer, mobile devices. Looks like your Setup is similar to mine. I have mine with the modem installation cable to my Cisco router that broadcast wireless signal. Then I have my devices on this router (computer, printer, mobile devices).

  2. If you use Airprint, you put your printer on a network or wireless. Since your printer is a model of dnf (D - duplex, n = network, f = fax), you must use a network cable and add it to your router. AirPrint is not supported via the USB port.

  3. If you remove the USB cable between the printer and the computer, you need to add your computer to the same network as your added to the printer. You can either do this via the ethernet cable or wireless depending on the capacities of the router and the computer. The important thing is that all the devices are on the same network.

  4. for other tips: make sure everything (computer, printer, router, mobile devices, etc.) are on the same network, otherwise you will not be able to print or have communication problems such as print jobs do not print.

  Good luck.

• How do you install the print driver FAX for m1536dnf in OS x Lion?

  Hi Forum,

  I have a Laserjet M1536dnf all-in - one network. When I install the driver under OSX Snow Leopard and Ubuntu, I have two shows of printers in the preferences panel. Regular printer and printer-fax MACHINE, so I can print to fax directly.

  But when I install the driver in OS x Lion, it shows only one printer, so I can't print to FAX directly. I checked the apple software update, there is no more than an update as well.

  Someone knows how can I install the FAX printer driver in OS x Lion?

  Thank you

  Noodle

  Hello

  Offer the product at a time print, scan and ability by retrieving the driver of the Apple software update.

  If you have installed the full features software, remove it by running the uninstall HP program located under Applications > CEJA-Packard and be sure to remove the existing print queue.

  Then Champagne for any update of HP software available.

  If the recovery of the printer HP Software Update fails for any reason, install the bundle HP Printer Drivers 2.8 below.

  Then the fax printer must be detected as well:

  http://support.Apple.com/downloads/DL907/en_US/HPPrinterDrivers2.8.dmg

  Kind regards

  Shlomi

• LaserJet M1536dnf print queue stuck

  Does not print the LaserJet Pro M1536dnf-order 3 days ago - stuck in print queue of waiting.

  Windows 7 (64-bit).

  No error message - yellow triangle.

  Printer will copy and run the config report that has the correct IP address.

  Print and scan doctor - he simply deleted document but problem persists.

  Have followed all the 10 suggestions in print and Scan Doctor (including uninstall and install with the driver 'later' but still no progress.

  Sprig12,

  Congratulations! ... and glad to hear that you are back on!

  Don't forget to let me know if you need help most.

  Also, if you would be so kind to mark it as an accepted solution so that others may be able to easily find this thread if they have the same problem that would be greatly appreciated.

• M1536dnf: FALSE alert m1536dnf printer Toner Cartridge

  M1536dnf AiO power lost during printing. Resumption of power, showed the paper jam. I removed the paper from the output tray, closed the door, and a sheet is released. Printer then began to show a warning "used cartridge in use', which will not disappear. It's a true 78A, and clear a paper jam is not "used". How can I fix this error?

  Hello

  You should not do something when this message appears, it should disappear; as it is just informative.

  I guess you could try a cold reset on your printer.  This set your printer to the factory settings, delete downloaded fonts, etc...  So what are you comfortable recongifuring the printer:

  Product resets

  To restore the factory the product's default settings, follow these steps.

  1. turn off the product.

  2 hold down the arrow button to the right and cancel at the same time.

  3 all by pressing two keys, turn on the product.

  4 continue to hold both buttons until the storage Permanent. init appears on the screen and then release both keys.

• Print compatibility remote desktop - product: Laser jet Pro P1606DN, Laser Jet Pro M1536DNF MFP

  Hello

  Want to know if the jet Pro P1606DN Laser or Laser Jet Pro M1536DNF MFP compatible with RDP printing without having to install drivers on the server.

  We have a Windows 2008 terminal server server runs on one end and 64-bit and Windows 7 32 bit on the other end clients.

  Is there a list available where we can see that the HP printers are compatible with the feeling of RDP?

  Thank you

  Mahen

  Habitat for humanity Intl

  Hi Mahensr,

  Follow the steps outlined in the document below.

  Installation of the software of the printer on Windows Server 2003 or 2008

  P1606dn drivers:

  
  http://h10025.www1.HP.com/ewfrf/wc/softwareCategory?OS=4024&LC=en&cc=us&DLC=en&sw_lang=&product=4110410#N172

  M1536dnf drivers:

  
  http://h10025.www1.HP.com/ewfrf/wc/softwareCategory?OS=4024&LC=en&cc=us&DLC=en&sw_lang=&product=3974279#n174

• Automatic document feeder stop working on printer HP M1536dnf MFP

  Hello.  The automatic of the document (BAA) on my all in one work suddenly quitting coppier.  I cleaned but still nothing.  When you set up a sheet of paper in the tray and it depresses the lever on the power head, he normally had a message like 'paper' on the LCD display.  Now, nothing.  I thought that the driver's head may have failed so I replaced it with a spare that I had but this diddnt help either.  I'm not sure why the ADF will not work, but it turns out quite invonvieiant for my work. If anyone has had this problem and if so, were you able to fix?  Thanks in advance.

  

  Model HP Laser Jet Pro M1536dnf MFP

  Hey @MarioFleecy,

  If the NVRAM reset on your product could not solve the problem with your ADF, then the next step would be to maintain the product that we have exhausted all the troubleshooting steps.

  I would recommend calling HP support and inform the agent of all the steps that we've come for troubleshooting. When you do that, you will be able to discuss what alternative options are available.

  HP Technical Support can be reached at the: 800-474-6836.

  If you do not live in the United States / Canada region, please click the link below to get help from your region number.

  Worldwide contact HP

  Good luck!

• LaserJet M1536dnf MFP: LaserJet M1536 don't not printing Mac laptop, all lit LEDs under LCD

  My LaserJet M1536 suddenly no longer print from my Mac laptop. And Yes, I downloaded the HP printer from the Mac App Store software was last updated.

  Under the LCD of the printer are three lights that stay on, even after that I power on and off the printer (the LEDs are green, the orange exclamation point and the orange point then). I don't know that the fact that all three LEDs remaining on the means, but it seems to be indicating a problem exists.

  Please help with advice to rectify or isolate the problem at least.  Thanks in advance.

  Do a google search, but the price will be high.  You can try a company call metrofuser.com because they can get a better price.  Good luck.

• configured printer / connection

  I just bought a hp - Laserjet pro m1536dnf (HP) printer, that has no connectivity wireless.

  Currently, I use a (WR) wireless router to access the internet at home.

  Q1: Can I use a network cable to connect my printer the WR, without using the usb cable provided in the box to connect the printer directly to my laptop and print documents?

  Assuming that the answer to Q1 is Yes, I want to better understand:

  Q2: while the WR transmit internet (wireless) signal to my laptop, the WR will also transmit printer signal to my laptop? This is why I am able to print from my laptop without direct connection to usb cable from my laptop to the printer?

  Hello

  Connect the printer via a wired ethernet cable or wireless makes no difference.

  As long as the computer and the printer connected to the same network (an any of them can be connected either wired or wireless) you can install the printer on the PC and enjoy its functionality.

  Kind regards

  Shlomi

• HP model M1536dnf dead

  We have a HP m1536dnf dead, no display. Need help to make the cold reboot. Thank you

  Did you already open the toner?

  Here is another printer that will use this exact toner.

  HP LaserJet Pro P1606dn printer

• Problem setting up my iPhone, iPad with printer MFP HP 1213

  I have an iMac, MacBook Pro, iPad, iPhone 3, iPhone 4, iPod. Almost all have the iOS responsible henriq. I have also two HP multi function printers: HP LaserJet M1536dnf MFP so MFP HP LaserJet Professional M1213nf. Recently, I downloaded PrinterControl from the iTunes Store and installed on my iPhone, iPad etc. The above two printers are connected on two separate wifi networks. The 1536 printer when I try to connect to my iPhone, the iPad with PrinterControl I am able to print, scan and do everything. All handheld computers are able to immediately recognize the printer. Unfortunately when I try to connect to 1213 all-in-one that is located on another wifi network and is connected to a time Capsule I am unable to do so. The PrinterControl says "no printer found. On the other hand in all the devices of Air print feature is working perfectly fine. I can take my fingerprints of mail and it is recognizing the MFP 1213 easily and get the made impressions.

  Even after through many forums and discussion forums, I couldn't solve the problem. I contacted HP support and said I need to contact Apple support. I also tried and contacted the Apple support which in turn said that because the PrinterControl is a third-party application they will not be able to provide any help/support and Air Print being workinf fine then there is no problem with Apple products. Please help, how to reolve the question and 1213 HP MFP get well with Apple products.

  Hello

  I'm afraid that this behavior is expected because the M1213 is not supported by the HP printer control application.

  You can find this information listed for the HP LaserJet Pro M1210 Multifunction Printer Series within the category Printers HP LaserJet Consumer below:

  http://support.HP.com/us-en/document/c02814760

  Shlomi

• LJ Pro M1536dnf MFP: is more duplex

  My LaserJet Pro M1536dnf MFP stopped automatic duplex printing. Once I choose duplex printing and rather fo print on both sides of the paper, the document was printed recto with each page on a sheet of paper. I tested and it will do is more duplex copy either.

  I didn't hear unusual noises or get the error codes.

  Any ideas?  Others have the same problem. Other that this question is a great printer, especially for the price.

  This printer is a replacement guarantee for one who stopped duplexing while in warranty period. The first unit duplex copies always worked.

  Hi John_Mrtz ,

  Thanks for letting me know.

  You can go only with firmware updates. You can rerun the update of the firmware, but probably it will show that it is already updated. I tried the same exact setting, that you used in the laboratory for the Laserjet M1536 and he did the double-faced properly document. It looks like a hardware problem with the device. I am surprised however that the test internal printed duplex test page.

  There is still one thing that we can try reset the printer back to factory settings. I can send you this information in a camera
  Message. In the forum next to your handle name simply click on the envelope to see.

  Thank you.

• HP 1536dnf: M1536dnf cannot send faxes from charger only from glass.

  I can't send faxes to high feeder if I place the fax on the glass. Message I get is always "the fax storage" and the makers of fax to be sent. Updated firmware to date with no solutioin.

  Welcome to the HP community @perlfather,

  I read your message on the message "memory fax" you're noting on your LaserJet M1536dnf and no faxing. I suggest you power reset of the printer and to make sure that the printer has a connection directly to a wall jack, avoiding power bars and surge limiters.

  • Turn on the printer.
    With the printer, unplug the power cord at the back of the unit.
    Unplug the power cord from the wall outlet.
    Wait at least 15 seconds.
    Plug the power cord into the wall outlet.
    Reconnect the power cord to the back of the unit.
    If the printer does not by itself, press the Power button to turn it on.

   

  Let me know what happens please. I will do my best to help if necessary!

  Send me a 'thanks' by clicking on the thumbs upward! If these steps help to solve the problem, please press "Accept as Solution" too!

  Best wishes!

• Cannot sweep M1536dnf after reformatting computer

  After the formatting of two computers in our office, they can scan is more from our M1536dnf, which is connected by Ethernet to our local network. The error message says "Scanner communication cannot be established. If make sure that your product is powered, check the connection and make sure that your network is working properly. If these conditions are correct, restart the product and try to scan the image. »

  They could sweep before formatting and other computers in the office can still analyze the documents. They have the operating system has not been changed (they were running Windows 7 before and are equipped with Windows 7 now, the same as all computers in our office). I tried to update the firmware on the I tried version 4.3 HP print and Scan doctor and it says there is an error analysis of Windows (WIA). I tried what they recommend, which is completely uninstall the software, reboot, and reinstall with the latest version of software complete features. I tried turning all involved market (printers, computers, network, equipment). I checked that the Acquisition of Image Windows (WIA) service is set to automatic. I tried to disable the built-in Windows Firewall and we do not use any antivirus software, or override the firewall on the local Ethernet. I tried manually specifying an IP address, which is not in conflict with all other IP addresses on the network. In all of this, I can always print these two computers and other office machines can print & scan very well. We have another scanner in addition to the office and these two computers can still scan using this one, but it doesn't have as many features. The HP ToolboxFX still works of these two computers.

  I'm full of ideas on how to solve this problem. It's particularly embarrassing because it worked before and continues to work on other desktops. Clues as to what I should try next?

  Any suggestions you mentioned did not. No change in behavior. However, I wasn't ready to admit defeat. After you check with the inspectors of package & various parts of the debug windows, I FINALLY found the solution! Therefore, I thought I'd share for someone else in the future who has a similar problem.

  These two computers have been executed under limited user accounts, and at the end of the day, it's a bug in the way the HP drivers in the WIA service user account permissions. It was totally an easy workaround solution, although - raise the WIA service for a user admin that can interact with other restricted users. Then, it has permissions to do what he wants!

  Directions for use:

  (1) on the computer target under the normal user account, press Start, in the search box type services.msc. Right click on the program that appears and select "Run as Administrator". Enter your user password or click on next to go to the UAC popup, if necessary.
  (2) locate the service called "Windows Image Acquisition (WIA)" and double-click it.
  3) click the connection tab, and then change this service to log on under a Local System account. Click here to allow the service to interact with desktop. And then click OK.
  (4) reboot (or if you really don't want to restart & know what you're doing, you can just stop & restart the WIA service twice)
  (5) enjoy!

  Everything works now.

• Cannot use fax function after rename the name of the printer

  I have an MFP HP LaserJet M1536DNF connected by network.  I have run the full setup package by the CD of the product, or on the web, complete update install the driver package.  The problem is the default printer name after installation as like "HP LaserJet 1530 MPF Series PCL 6" and can not be changed through the installation.  When I tried to change the printer name on the windows 'Printers and faxes', he managed but the fax doesn't work anymore after that.  It says probably 'impossible to find or connect the printer' after I click the fax or print the document to the fax printer.  However, I can still use the printing function after the name change.  The only way to solve now is to uninstall all and reinstall again, even I tried to rename back the name exactly for the name of the printer.  I use Window XP Pro SP3 with .net Framework 3.5 already up-to-date.  Thanks for the tips.

  Hi Cheetah12,

  Sorry to misunderstand.  I mean there is no option to not rename the printer when you run the complete package installation wizardfirst, but not the fax configuration wizard.

  In fact, I must mention once again that I have can print and scan even I renamed the printer.  Things I can't do the HP Send Fax or fax HP Setup Assistant and so, which means my fax machine was not working properly.

  Therefore, I follow the document from HP that you post step by step and of course the diagnosis by downloaded HP Print result and doctor Scan for both printing and scanning are in good health, all in green light!  But cannot always solve the problem of the fax.

  However, I finally found my way to solve the problem, which is just rename back the original printer name in the registry.  As a result, the printer in "Printers and faxes" which always shows the famous name, but actually running with the original name of the printer.

  In any case, thank you for your kindly help and fast track.  But I suggest there should be a direct way, like having an option to rename the name of the printer while the first installation wizard on your next updated version.  This will certainly help users who have to install 2 or more of the same model printer, to indicate which printer works easily.