Pro L10: After using a wireless mouse, the touch pad has stopped working

Pro L10. After using a wireless mouse, the built in touch pad has stopped working properly. At the start of the keypad icon touch shows and the touchpad works intermittently, after a few minuets, the icon disappears and the touch pad stops working. In the control panel / mouse & or device drive I can how the program works, then disappears.

I deleted the software and reinstalled nothing doesn't. In some cases, I get a message that a pointer is on.

Can you help me?

Advertisement

Hello

It seems that the wireless mouse or mouse wireless drivers/software has a bad influence on the touchpad.
I put t have a good solution for this problem. Well, you can consult the page of the Toshiba driver for latest driver updates. If the updates doesn't solve this problem I suggest to use either the mouse wireless and disable the touchpad with FN + F9 key combination or use a regular USB mouse.
I guess that you are having regular problems with a USB mouse.

Tags: Toshiba

Similar Questions

  • Wireless mouse (PA3706E-1ET1) Toshiba has stopped working

    Hello

    My wireless mouse suddenly stopped working for no apparent reason. The computer recognizes that the mouse is attached, but nothing works. I tried the obvious things like replacing the batteries, removing the USB and reconnect it and download the drivers for the mouse, but his does not work. It does not move the cursor, the buttons do not work, nothing. Any suggestions on how to fix this would be appreciated.

    Hello

    > It's not moving the cursor, the buttons do not work, nothing. Any suggestions on how to fix this would be appreciated.

    Have you tested this mouse in connection with other computers or laptop?

    Recommend doing this if the mouse does not work on other systems, then I guess there is a hardware problem and maybe you will need to replace the mouse.

  • My wife has a Mini IPAD and the touch screen has stopped working. If anyone has had similar problems and if so is there a cure?

    HHas someone at - he had problems with the IPAD MIni touchscreen unresponsive? If so, can we do anything to fix the prob?

    Try these standard troubleshooting steps in the following order:

    Reset: Press the home and power buttons at the same time and hold them until the Apple logo appears (about 10-15 seconds). No data will be lost.

    Catering: Connect your device to iTunes on your computer, backup, and then select factory restore.

    See here for more details on the restoration: https://support.apple.com/en-us/HT201252

    If none of these work your device could have developed a hardware problem. Contact Apple technical support: http://www.apple.com/contact/

  • After execution of the new updated Adobe, HP Elitebook 2760p left click on the touchpad button has stopped working.

    Original title: left click not working not not on HP laptop

    On my HP Elitebook 2760p running Windows 7 Pro 64 bit, left click on the touchpad button has stopped working.  The right click works, the works of pad, (scrolling and click on) it's just the left click.  It started after the execution of the new update of adobe. I tried to uninstall and reinstall the driver synaptec. I tried the mouse fast and slow speed. I tried pressing rigid, flexible, in different places. I would try to uninstall the update from Adobe, but it won't allow me.  So I uninstalled Adobe Reader and re-installed. Still nothing. Any suggestions?

    Hi cyrilmillot,

    You try to run the Adobe Reader removal tool to remove the Adobe reader completely the system software.

    See the link to Adobe to download the removal tool:

    Adobe Reader/Acrobat removal tool

    After retiring, you can check whether the left click works. If it does not, you could get in touch with Adobe support for further assistance on this topic:

    Adobe forums

    http://helpx.Adobe.com/support/

    If the problem persists, then it may be a hardware problem and you may have to contact HP support for further assistance:

    HP support

    HP laptops - use and configure the TouchPad (Windows 7 and Vista)

  • I get the message "firefox has stopped working" after closing browser

    Hello.

    My problem is that when I close the FireFox browser, I get the message "FireFox has stopped working". It's pretty boring. I have read some other posts here that describes a similar problem and we tried some of the suggestions in them including:

    A clean install, a reset of the browser, running in safe mode, uncheck hardware acceleration, disabling Extensions and plugins one at a time, uninstall my antivirus (avast), backward to 23.01 and audit version run in compatibility mode that someone claims to be helped. None of this has been effective.

    It seems that after a reboot of the computer, the browser will be ok for 2-4 closures and then it will start by the message at each end. In addition, after uninstalling avast was good for 6 closures. Roll back also gave me approximately 6 free message closures. But then, the messages and does not stop.

    Is there anything else I can try? Thanks in advance for your suggestions.


  • SyncUp software displays the message "SyncUp has stopped working".

    SyncUp software displays the message "SyncUp has stopped working" what can I do to fix this? Thank you

    Hello

    1. what operating system are you using on your computer?

    2. What is the brand and model of your computer?

    3. it worked very well on your system before? If Yes, you did it all software or hardware change before the show?

    Method 1

    I suggest to put the computer in a clean boot state and then try to open the program and check if it helps.

    Note When you perform a clean boot, you may temporarily lose some functionality. When you start the computer as usual, the function returns. However, you may receive the error message, or you can experience the original behavior.

    How to solve the problem by running the clean boot in Windows 7:
    http://support.Microsoft.com/kb/929135

    Note: Once you have completed troubleshooting, perform the steps in the step 7: to reset the computer as usual.

    Method 2

    Uninstall and reinstall the software SyncUp.

    Uninstall or change a program
    http://Windows.Microsoft.com/en-us/Windows7/uninstall-or-change-a-program

    Note: Uninstalling the software will erase all the data associated with it. You must redo all favorite and set up anywhere after settings put it back.

    THIRD PARTY WARNING: Using third-party software, including hardware drivers can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the use of third-party software can be solved. Software using third party is at your own risk.

    See the following help link:

    http://en.community.Dell.com/support-forums/software-OS/f/3526/t/19391777.aspx

    It will be useful.

  • I have a Toshiba satellite L455D laptop and the touch pad does not work

    If I plug my usb wireless mouse that works, but when I unplug it the touch pad does not work

    Have you checked to see if your laptop model has a physical button around the mouse pad that allows & turns off?  If it does not, many cell phones often have a software switch that can toggle the on & off power mouse pad.  It is usually triggered by a combination of function keys (key Fn + one of the F1 to F12 keys).

    Take a close look at the row of the top of your keyboard and see if you can find a key that has a small symbol that looks like a mouse pad.  If you find one, try pressing it in combination with your Fn key to see if your mouse pad features returns.

  • My option "open in a new tab in the same window" has stopped working.

    After working for centuries without any problem, my option "open in a new tab in the same window" has stopped working.  Support suggested that I go to tools, select internet options and open tabs, and then select open in a new tab in the same window option.  I did as instructed and concluded that this option under the tabs was already selected and unchanged.  I changed this option, closed my browser and restarted my computer as instructed.

    As before you follow these instructions, and when viewing online and wish to open a link in a new tab in the same window I once again this desired option.   Internet does not take into account my instructions and opens my link in a new window.  This is extremely irritating.

    Does anyone have a solution?

    Hello

    What version of Internet Explorer work?

    You can try the following steps and check:

    Method 1:

    You can reset Internet Explorer 9 settings and check

    http://Windows.Microsoft.com/en-in/Windows7/reset-Internet-Explorer-settings-in-Internet-Explorer-9

    Warning: him reset Internet Explorer settings feature might reset security settings or privacy settings that you have added to the list of Trusted Sites. Reset the Internet Explorer settings can also reset parental control settings. We recommend that you note these sites before you use the reset Internet Explorer settings.

    Method 2:

    How to reinstall or repair Internet Explorer in Windows 7, Windows Vista and Windows XP

    http://support.Microsoft.com/kb/318378

    Warning: Reset the Internet Explorer settings can reset security settings or privacy settings that you have added to the list of Trusted Sites. Reset the Internet Explorer settings can also reset parental control settings. We recommend that you note these sites before you use the reset Internet Explorer settings.

    Important note: ignore in place update from the above mentioned link.

  • Satellite L500D-144 - CCC of the host Application has stopped working

    Ladies and gentlemen,

    My PSLT6E - 007004GR is almost a year.
    This month, there was an update - possibly to leave Microsoft - and since then popt always at startup in Windows 7 this window and look for solutions:
    Catalyst Control Center. The host Application has stopped working, it is looking for a solution.

    A new installation of the driver graphics card and Catalyst Control Center has not changed. Instead, a standard Microsoft graphics card driver is installed.
    Reset of the system for the month of October has also asked nothing, after fresh updates, the problem recurs.
    Is it reproducible.

    Have already reported more customers or I'm the first?

    What can you do to the problem?

    Sincerely,

    CBluebaerchen

    Hello

    > Reset of the system for the month of October has also asked nothing, after fresh updates, the problem recurs.
    To do this the display of Windows Update driver update?

    If so, restore the system to an earlier point and disable this update of the display driver and choose only the updates of Windows. That s enough.

    Otherwise, you can try running CCleaner. It can clean and fix registry problems.

  • Why my Catalyst Center: the host application has stopped working?

    When I log on my computer, a window opens in two separate occasions stating that Catalyst Center: the host application has stopped working... How can this be repaired?

    Hi Missy,

    This probably isn't a problem MSE or malware.  It could be a problem with the video software (which is otherwise commonly) and I have it on my system as well for my ATI graphics card.

    This just started recently - as the last day or more?  If so, try a system restore to before it started to see if that helps. If you use Windows 7, seehttp://www.sevenforums.com/tutorials/700-system-restore.html. If you are using Vista, seehttp://www.howtogeek.com/howto/windows-vista/using-windows-vista-system-restore/. If you are using XP, seehttp://support.microsoft.com/kb/306084. Sometimes this simple process made the rounds and sometimes that doesn't help - but it is easy and worth if she has recently begun.

    Good luck!

    Kosh

  • 6540 b after upgrade windows to windows 7 bi-ecrans has stopped working

    After upgrading my computer (6540 b) to windows 7 the bi-ecrans has stopped working. Help, please

    40043330 wrote:

    After upgrading my computer (6540 b) to windows 7 the bi-ecrans has stopped working. Help, please

    Hello

    You have installed all the necessary graphics drivers? Is there a graphics dedicated ATI Radeon HD, etc? If Yes, go to the ATI Control Center and have a look for dual monitor settings.

  • The program executable has stopped working

    Remember - this is a public forum so never post private information such as numbers of mail or telephone!

    Ideas:

    • You have problems with... of programs a SSC downloaded for smpt installation
    • Error messages. the program executable has stopped working... a problem caused blocking the program works correctly. Windows will close the program and notify you if a solution is available
    • Recent changes to your computer. None
    • What you have already tried to fix the problem.no I don't know what to do

    Confirmed that the program is compatible with your version of Vista and the hardware in your computer? http://www.microsoft.com/windows/compatibility/windows-vista/.

    You can try to uninstall the program, download a clean copy (in case where the original has been altered) and re - install the new download and then see if the program works.  If this does not help, try right-clicking on the executable and click on run as administrator and see if that makes a difference.

    I hope this helps.  If this isn't the case, follow the advice implied by Malke response and contact technical support by the manufacturer of software for assistance.

    Good luck!

    Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

  • "CatalystControlCentre: the host application has stopped working".

    I get this message when I boot: ' CatalystControlCentre: the host application has stopped working. . Caused A problem blocking the program works correctly. Windows will close the program and notify you if a solution is available. " This happened after I got malware and have since sent to quarantine. A / the result is that the wallpaper is gone replaced by a black screen. Some of the icons on the screen and the line along the bottom disappeared. How can I fix it? What I have to find and pay a professional to do it, or can I fix it myself?

    Hi Eagle-B


    Did you put the virus in quarantine?

     

    It seems that you still have the virus or malware present on the computer. I suggest you to contact the team of experts on the issue. Also, you can visit the Microsoft security essentials forum for assistance for the number and check if that helps.

    http://social.answers.Microsoft.com/forums/en-us/msescan/threads?filter=answered

     

    I hope this helps.

  • How to solve the questviewer.exe has stopped working windows 7

    How to solve the questviewer.exe has stopped working windows 7

    using the analysis

    http://www.Malwarebytes.org/

    Make sure your system is clean first. use ccleaner to get rid of junkfiles http://www.piriform.com/ccleaner/download

    Also look for viruses either using avast and spyware using superantispyware

    go to msconfig (type in the search box in startmenu or run in xp, and then press enter) then prepare your computer to clean boot by disabling all startup items and any of the services of windows, and then restart your computer. See if it makes a difference? If it did then you know who caused the problem.

    you will also need to know is that "questviewer.exe"? It belongs to a program? If the answer is Yes try to update or reinstall the program, but before that make sure that the program is not hamful to your pc.

  • I use windows 7 and auto start program has stopped working and I can't find a way to recover.

    I use windows 7 and auto start program has stopped working and I can't find a way to recover. Also, I was not able to transfer files on disk or any other storage device, their there on the computer and it says that they work very well, but I can't transfer anything to them.  They will play a disc or view data on a disc that has already been done but don't transfer to the drive if I want to add new files or data to it. Drag and drop is going through the motions, but shows red circle icon.

    [Moved from comments]

    Probably tell you autoplay?

    Control Panel > programs > default Prorams > Change AutoPlay settings

    Or

    In the search programs and files, enter, AutoPlay

Maybe you are looking for

  • How can I change the keyboard on Portege R500?

    Hello everyone, I get a Toshiba - 10J Portege R500, with the QWERTY keyboard.I want to change it with the QWERTY keyboard, because I usually use the French. But I don't know on the net the explanation or detail to achieve this.Someone get some photos

  • Application builder appears complete but does not create executable not

    I'm working on a major project (~ 5000 screws, LV2011 SP1, Win7 32 bit) and have recently from problems with the Application Builder. This is after 3-4 years of success is based on this project... When I try to build my application of following highe

  • Exclude an iteration

    Hello. I must exclude a value of a forloop, and I did not how to... I made an example of what I want to do on the vi that I join Explanation: When the iteration 5 appears, we go straight to the value 6 without taking care of what we are supposed to d

  • voglio cacciarmi dalla community

    NN voglio stare più who

  • Adding memory 8311-62U office

    I have trouble finding the memory to add to my desktop (computer NetVista 8311-62U). Currently I have 384M and am running XP. SO, I want to add to the system board. Anyone know what kind of memory and where I can buy? Thank you


HashFlare