Problem for my compact DAQ recognize the parallel port

Similar Questions

• For some reason any, that my printer has enough work and when I plug in my camera to download images, the computer says it does not recognize the USB port, which could be the pronblem?

  My printer does not work (it is said that the computer does not recognize the USB port (this also happens when I plug my camera to download the photos) I checked everything I know to check, which isn't too.)

  My printer does not work (it is said that the computer does not recognize the USB port (this also happens when I plug my camera to download the photos) I checked everything I know to check, which isn't too.)

  When did this problem start? What did you change shortly before it all began?

  Please quote the exact text of the message you get, verbatim.

• Driver files that run the parallel port and USB port

  In the system information utility where to look to find the parallel port and the port driver USB, name of file that manages these?

  Know the drivers specific, is only half the story.  Why you looking for these drivers?  You have problems with your parallel port or USB port?  This can be caused by problems with drivers or it could be a hardware problem (hard to diagnose a hardware problem without good parts to swap and test).  If you need to update the drivers, you must use device (not msinfo32) Manager - or maybe clicking on an executable file that loads the drivers automatically (depends on how it is sent by download).

  Go to the Device Manager by going to start / find and type Device Manager and enter and then double-click on the program icon that appears.  Check each device to a red x, yellow! or white?  These identify devices with problems probably (drivers, but also of conflict or something else).  Click on each for more details and troubleshooting tips.  If you need drivers (I assume that you want to the parallel port and USB ports), get the computer dealer or the manufacturer of the device (NOT of Microsoft Updates).  In fact, you must disable automatic updates in Windows Update driver as follows: http://www.addictivetips.com/windows-tips/how-to-disable-automatic-driver-installation-in-windows-vista/. Follow these steps to get the drivers: http://pcsupport.about.com/od/driverssupport/ht/driverdlmfgr.htm.  Once you have the drivers, you can install them via the Manager device as follows: http://www.vistax64.com/tutorials/193584-device-manager-install-driver.html.  Or run the Setup program of driver provided by the vendor of the computer or the manufacturer of the device.  Be VERY careful get Vista compatible drivers for these devices are difficult to identify (they usually come with the numbers of model or something like that if they can have serial numbers) and using the wrong drivers could make the problem (whatever that is) worse.

  If you update the drivers succerssfully and the problem persists, then it is probably a hardware problem.  In this case, contact the manufacturer of your computer for technical support (hopeully it is still under warranty) or bring it to a professional computer repairman (NOT Geek Squad or one of those big store centers because they don't really know what they're doing and charge a lot for this level of expertise) to have the components tested and possibly replaced.

  I hlpe that aid.

  Good luck! Lorien - MCSA/MCSE/network + / A +.

• The use of pins of status (4 outputs) and data (8 entries) of the parallel port pins at the same time.

  Hi all

  I'm a newbee in labview. As part of my project work, I need to get 8 digital inputs and send 4 digital outputs.so I think to use the Parallel Port on the pc.i can make use of 8 datalines for entries. I found the site NOR is it possible to use status for output pins. But is it possible to use status for output pins pins and data for entries to the time.please help even me also mention of the measures to take, or keep in mind while implementing.also include any example vi that could be useful.

  Thanks in advance

  I would recommed you to NOT use the parallel port. Now a day you have hardly a PC with parallel port. also if you have some old PC then most likely last version of LabVIEW (e.g. 2010) will need a lot more memory RAM and processor.

  If you want a solution very very low cost then I would recommend using an arduino to that effect. You can then download LabVIEW Interface for Arduino and start working.

  If you continue to use the parallel port, then you could try (I haven't worked with parallel port and have not tested the following solutions)

  Download VIPM and then install the enclosed package. It will add the port e/s palette in your labview. and you can use it.

• Using the Parallel Port

  Windows does not allow for QBASIC uses the parallel port (address = 888 or 378 h)

  If you know the 3rd party software that there access to this port it please tell me

  and why user port does not work with windows vista

  Most any version of Windows that is based on the new testament 'sources' (Windows NT, 2000, XP, Windows 7, Server 2003/2008) all do not support 'direct' access parallel ports / series. This is normal.  You may need to add a non-Microsoft Windows 'core' driver to allow this access.

• Aspire One D255E don't look for a printer connected to the USB port

  My D255E an Aspire don't look for a printer connected to the USB port.  I've never used a printer on this computer before.  Windows 7 Starter will support a printer?

  It should be.  Try these steps and results reports:

  When you turn on and connect the printer via USB, shows tasks for animation in the system tray at the right end of the bar, click it and monitor driver installation.  If the pilot goes then printer must print and perhaps scanning of base via the Windows fax and scanning utility.  To find such a piece of utility type its name in the search box.

  If the driver does not load type of devices and printers in the box to start the search, open it, check if printer is already displayed, right-click on it to open the properties, and try to print a Test page. If it does not print right click on printer again to solve problems.

  If the printer is not listed visit Support downloads of the printer Web page to download and install the base driver.  If a wireless printer, you will need the complete package to do it fully implemented.  If you want to be able to scan from the top of the printer to the PC, then you also need the full package.  Keep track of the configuration screens when you install the software.

  If you still have problems after return the exact error with photos if possible.

• How do a program that would stop or Activ LEADS through the parallel port.

  Original title:

  parallel port programming in 64-bit win

  Hello
  I worked for a long time on it. I want to do a simple program, that could turn some LED via the parallel port.
  I found some examples. they were all used "inpout32.dll. is it possible to do it on 64-bit system?
  Please help me :(
  Thank you very much.

  Hello

  What is the brand and model of the computer?

  To improve assistance to this subject, you can ask your question in the MSDN Forums.

  http://social.msdn.Microsoft.com/forums/en/categories

• Use of the parallel port

  Hello

  I have a lot of experience with earlier versions of Dasylab (up to V9) and recall his ability to use the parallel port of PC as a "quick & easy" way to get digital input/output lines of the PC. If my memory serves me well, done by activating the sound card driver?

  However, I recently bought the latest version (V13) and it seems the digital input / output modules are now grayed out when the sound card driver is selected, i.e., it only allows to input/output analog (audio).

  Is it still possible to drive this port with the latest digital lines... .or have I missed something?

  Thank you best regards &,.

  This feature has been removed a few versions ago. With the changes in Windows after XP, it became problematic.

  If you are still using XP with DASYLab 13 and will always have a parallel port, you can retrieve the V9 sound card driver and try it.

  If you need me to download it or email it to you (it is usually an illegal attachment), let me know by private message with your email address.

• to detect the meter output via the parallel port

  I need to detect the meter count trigger, to perform an operation every time. I think passing the input signal pins (pins of status or control). The meter uses is omron H7EC.

  I lowered the voltage of 24 V to 5 v with resistors.

  But I can't get the entry via the parallel port.

  All the stems of my status are still high.

  What should I do, please help.

  In the parallel reading write loop.VI, the splash screen is attached.

  I suspect the entries on the parallel port pins have a resistance low pullup to 5V, so they tend to float high (logic 1).

  Try to add a 4 700 Ohm resistor between pins of entry and mass of the parallel port, see if it then reads down pulldown (logic 0). If so, then keep the resistance in place and connect the signal of 5V that you want to monitor at the entrance.

  -AK2DM

• Virtual PC on MacBook Pro doesn't recognize the Firewire Port

  I'm trying to run a Windows-only based software (Adobe Visual Communicator) and plug my camcorder via Firewire to my PC virtual VMWare Fusion.  However, the PC does not recognize the Firewire port when the camera is turned on. I have the correct cables, I can see the camera from Mac OS.  Please share thoughts or ideas.

  Sorry, but you're out of luck.  At this point, NO virtualization software is able to firewire devices to their guests.

• Dell Inspiron 531 s problem of power/does not recognize the hard drive

  My Office does not illuminate. I replaced the power supply. No, it powers on but does not recognize the hard drive. It gives an error as SATA 0 None SATA 1 no SATA 2 No. How do we know that the cables are properly connected. I feel like I'm very close to solving the problem but don't have a clue what that next step to follow

  The original PSU had 4 sets of cables and connectors.  The new power supply has 5 sets of son.

  aries7531

  From your post, I guess that the configuration of the system now recognizes the hard drive?

  If you do not have a floppy drive, then BIOS can find the player who isn't there, it returns this error.

  Make sure that the floppy drive [drive A] is disabled in the [BIOS] installation system, page 173, so that it is no longer looking for the disc and see if this stops the error message.

  If the hard drive is recognized in the configuration of the system, he now knows in windows "My computer" or in "disk management, [right click on 'My computer' and select 'Manage', then disk management]."

  Bev.

• Bridge for Mac does not recognize the phone

  Hello.

  I am wanting to get pictures on my Sony Xperia 1 on a MacBook Pro. The Mac running OS X El Captain 10.11.4. The phone is Android version 5.1.1 and the bridge for the Mac version is 3.6.3602. I use a Sony cable (model EC450). When I plug in the phone, the phone displays signs of chargin and bridge are activated. However, bridge continues to inform me that no Xperia device is connected.

  Can help you.

  Thank you very much

  Hi Frankieneedshelp,

  Why not try using the new Xperia for Mac companion, it replaced the bridge for Mac and could very well resolve the connection issue you have.

  Xperia for Mac companion

• HP930c driver for Compaq Presario again with no parallel port but...

  I have a HP 930C printer, which works very well with as a local printer on the Dell desktop computer. I just bought a new laptop Compaq Presario CQ57, running Windows 7 Edition Home Premium, which I have "networked" to the Dell. Everything works fine BUT I want to print on the Compaq 930c, 'through' the Dell printer.

  In other words, using the 930c as a network for the Compaq printer, never as local Compaq printer.

  PROBLEM:

  to do this, I need a 930c on the Compaq driver: the original driver is on a DVD / CD that tells me that Win 7 is not up-to-date enough to Win 7 process, download the drivers from HP tells me the driver built into Windows 7 (!), but Win 7 can not finish installing the driver because the process requires that the 930C is connected to the device of Win 7 (Compaq). But the Compaq has no parallel port (only USB) so I can't plug it! And nor would I, I want to do all my printing via my network domestic (IE "by the Dell).

  Useful thoughts or suggestions on how to solve this problem would be greatly appreciated - please!

  Best regards

  dutchted

  Hi dutchted,

  Try following the steps below to manually add the shared printer:

  First step: find the host name:

  Since the Dell PC, right click on computer and select Properties.
  Take note of the name of the computer.

  Second step: find the share name:

  Enter the control panel > devices and printers.

  Right-click on the 930c printer, then select printer properties.

  Enter the sharing tab, and take note of the share name.

  Third step: define the shared printer on the client computer:

  1. Enter the control panel > printers and faxes.
  2. Click Add a printer.
  3. Select this option to Add a local printer.
  4. The bottom of the screen, create a new port by selecting the local railway.
  5. Set the port as \\COMPUTERNAME\SHARENAME name using the above values.
  6. Search for deskjet 930C nder H, if you do not find the driver, Windows Update, click wait several minutes until the list will reappear and select the printer Deskjet 930c, and then click OK.
  7. Follow the steps to complete the wizard, and try to print.

  Shlomi

• BlackBerry Smartphones Pls help me my 9860 touch hangs when boot nd the system does not recognize the usb port when it freezes on startup

  Recently, my 9860 touch starts not finished... It stops at halfway when startup nd freeze... 2ndly starting my system recognizes usb d port, but when it comes to where it stops booting, the system doesn't see it me collapses more so to reload the software

  Hello Dtobs007

  Welcome to the community

  I recommend you try first method Mode without failure. Article ID: KB17877 How to start a mode BlackBerry smartphone without failure.

  Another thread explains how to fix this problem, for your reference.

  By JSanders. http://supportforums.BlackBerry.com/T5/BlackBerry-torch/BlackBerry-torch-9860/TD-p/2597381

  See you soon and good luck.

• Equium M50 will not recognize the LAN port - error: disconnected network cable

  I own a Toshiba Equium M50 and have problems with the Marvell Yukon 88E8036 PCI-E Fast Ethernet Controller.

  I used to connect through a Modem/DSL switch "ADDON" and had no problems. I then replaced the ADDON with an ADSL Modem/Router "NETGEAR" DG834G to win the wireless port, and since that time my machine won't recognise the LAN port. .

  I know that cables are OK I used with other phones and had no problems. I can also plug a PCI card to connect without any problems. It seems to me that if the Marvell Yukon 88E8036 PCI-E Fast Ethernet Controller has a problem with the netgear Modem/Router.

  Anyone out there with a similar experience and some tips/suggestions?

  PLEASE

  Hello

  For me this doesn't show t as a problem of LAN card but your router is a problem.
  Check Device Manager if the network card is correctly recognized. If there is no yellow exclamation point, so all is ok!
  You can try to remove the network adapter from Device Manager and reboot after new install driver LAN again.

  The question has looked after installing or connecting the new Netgear modem router.
  I would recommend to check first the settings or update the firmware on this router.

  I found more useful websites
  http://compnetworking.about.com/od/WindowsNetworking/f/cableunplugged.htm

  http://www.experts-exchange.com/Networking/broadband/DSL_Cable/Q_20381405.html