Problem in database recovery

Similar Questions

• problems starting database recovery...

  HP - UX 11.23
  Oracle 10.2.0.2
  I know that this has been discussed a bit. I spent a number of hours on this forum only today just read through the success of the research. I tried some of the "tricks" that have been described in the nets. But I still get the same error...
  
  
  My standby database lost connectivity to my receivers logs primary and arrested. I have not received any notification, because my scripts not implemented to capture this event...
  On my primary retention policy is 30 days of archive logs. After that, they are deleted. (I don't agree with it, but not my call)
  The waiting got more than 30 days out of sync, so I decided to just refresh the day before all.
  
  Cold backup is not an option, I did an alter system checkpoint to empty all archive logs. Then, I published a full hot backup.
  Once completed, I advanced and created a control file fresh intelligence, in addition to a fresh backup control file. In this exact order.
  
  I have transferred all the archive logs and control files db more waiting.
  
  I ran the commands:
  startup nomount;
  (SUCCESSFULLY)
  ALTER database base_de_donnees eve of Mount;
  (SUCCESSFULLY)
  recover the database pending;
  I have run all the files in the archives until newspapers she file errored saying that he could not find 'X' being the next sequence that was not in the directory. To my knowledge, is normal... time to stop recovery.
  
  When I went to cancel, I get the following error.
  Specify the log: {< RET > = suggested |} Filename | AUTO | CANCEL}
  ORA-00279: change 7313561157126 September at 2008-12-17 19:01:02 to
  thread 1
  ORA-00289: suggestion: /oraarch/swesc/1_13729_640853326.arc
  ORA-00280: change 7313561157126 thread 1 is in sequence #13729
  ORA-00278: log file ' / oraarch/swesc/1_13728_640853326.arc' is no longer necessary for
  This recovery
  
  Specify the log: {< RET > = suggested |} Filename | AUTO | CANCEL}
  Cancel
  ORA-01547: WARNING: RECOVER succeeded but OPEN RESETLOGS would get below error
  ORA-01152: 1 no file has been restored from a sufficiently old backup
  ORA-01110: data file 1: ' / ora1/oradata/peregrine/system01.dbf'
  
  Therefore, my understanding of what it means that you should always apply the logs.
  So I grabbed the newspapers who had been self created during the time I have it all rebuilding and applied.
  Same mistakes.
  
  I am at a loss here. How can he still be out of sync? Is it possible to force it to a specific sequence so that I can open successfully, and then close it up to complete the sequence?
  
  Thank you.

  You have a few missing logs to make your atndby consistent database, apply more redo (which may be a primary database redo log files).

  as you approach ORA-01152: 1 file was not restored from a sufficiently old backup is due to that you just applied it again archivelog files but don't do it again that is in the file primary journal again. That's what I was suggesting you im my last post which put your database in automatic or manual recovery mode after you have performed a primary database switch journal in order to obtain recovery located at the primary database redo log file.

  Khurram

• The database recovery/restore failed with unexpected error 509

  Hello

  The database recovery/restore failed with unexpected error 509

  In the Event Viewer, I had this error SEVERAL times every second.  He goes absolutely crazy.

  I don't know what to do with it.

  I'm with Windows 8 Pro running on a very stable computer with 8gig of ram, plenty of hard drive space.  Each single drivers updated Windows Update.  Everything is really clean except this error in Event Viewer

  Svchost SRUJet (1624): database recovery/restore failed with unexpected-509 error.

  Task category: registration/recovery

  Esentutl /p /r tried / everything but nothing wrong was found with those

  Thanks for any help.

  Exactly the same problem, nothing Microsoft recommended was the cause, scannow and DISM commands are returned without error.

  So I went to the event viewer and scrolled down to find, when these errors began to occur. So I found a few entries initially saying things like: an attempt to move the file 'C:\Users\xxxxx\AppData\Local\TileDataLayer\Database\EDB.log' to 'C:\Users\xxxxxxxx\AppData\Local\TileDataLayer\Database\EDB00008.log' failed indicating system 183 (0x000000b7) error: "cannot create a file when that file already exists.

  Then, I went to C:\Users\xxxxx\AppData\Local\TileDataLayer\Database\ and removed the files listed (e.g., EDB00008.log).

  Bingo, the errors will stop immediately.

• Problem creating a recovery on HP Ultrbook

  Hello

  I tried to create a collection set on my HP Ultrabook for months.

  The procedure works well until I need to insert media. This is the problem because the media is not able to reconginise even if the same media has been used to back up my file on the same lap all the time.

  The media have a lot of empty space (about 150 GB)

  I can assess the documents in the media

  Now, this problem could be critical because I might need to engage in the recovery, due to several errors that occur at this time.

  See you soon

  EUB

  Hello

  Looking at the free space you mention for this media, am I correct in assuming that this is an external HARD drive?

  If that is correct, then this is what is causing the problem as the recovery media creation application does not support creating a recovery on an external HARD drive media, you will need to use a (usually 32 GB) usb flash drive.

  Kind regards

  DP - K

• Netflix in Media Center returns a 'there was a problem of data recovery. "Check the works of your internet connection and try again" error instead of loading Netflix data.

  context: a previous thread with an identical title never responded, the problem just disappeared.  Well its been two weeks since then and the problem came back.

  somethings which may or may not apply: internet TV seems to work better in media center.  All updates have been applied to H.P. of Vista SP2. Netflix works fine in ie8 (such as the internet, of course). Tried to delete all the Internet Options, delete browsing history section of Internet Explorer. I get the same error message with my windows 7 professional media center, but netflix seems to play anyway (no game with vista). I recently installed quicktime alternative 2.72 to see what it was and how it worked, then removed and put back in quicktime.

  Tried / symptoms:

  -Remove all the browsing history (econcepts)
  -Same message on Win7pro but works even when (econcepts)
  -Works on Win7 no problem (omegafiler)
  -Works in ie 8 (econcepts)
  -Works in crome (Martin TX)
  -Consensus is that it started around December 30, 2009 (GeoffG1, johnetX, me)
  -Remove and reinstall silverlight (omegafiler)
  -Remove and replace netflix plugin (omegafiler)<- how="" did="" you="" do="" that="">
  -Netflix says: microsoft problem (Nitestalker)
  -Microsoft is silent (this thread - on vacation?)
  -Same problem on 32-bit and 64-bit VMC (JRSMiamiFL)
  -No applied update (johnetx)<- perhaps="" date="" related="" or="" drm="" date="">
  -Disconnect from netflix, you reconnect again - ultimately the same error (chicagokiwi)
  -Tried to reduce the number of items in the queues to well below the limit of 200 (econcepts)
  -Tried the register / unregister the third wire procedure, no joy (does not break anything else however)
  -Disabled the firewall, no change (econcepts)

  related topics:
  http://social.answers.Microsoft.com/forums/en-us/vistaprograms/thread/0c154c0a-1fcb-4353-8c5e-b394e885256d

  http://social.answers.Microsoft.com/forums/en-us/vistaprograms/thread/aaab24a0-4BB9-42FA-a5ee-46a733d6560f

  http://social.answers.Microsoft.com/forums/en-us/vistamedia/thread/f05f69c7-6456-4117-B302-27c08886ea1e

  Someone else knows Netflix not being is not able to connect?  It started yesterday (30/12/2009) for me.  I looked fine the day before without problem.  The message I get says "there was a problem of data recovery.  Check the works of your internet connection and try again. Ok.  I make it work with both my VMC - one with the service pack and the other without.  My OS updates have been loaded in early December, so I don't see how this could it be.  I searched and found this problem has come up before, but I have not found a solution.  I made NO changes to my HTPC.

  Those who have and solved this problem.

  UPDATE UPDATE UPDATE UPDATE UPDATE UPDATE *.

  2009-01-05 has attempted to start Netflix this morning and you know, it works on both my VMCs.  That's the good news.  So now the real questions are:

  Only 20 people reported it as a problem and only 6 on the green button.  I believe that it affected all the world with Media Center.  So why not discussed much?

  It already happened, causes a stir and silently slips without known cause or cure.  How can we find out what caused this and how to prevent it from happening again in the future?

  *******************************************************************************************

• Netflix in WMC «there was a problem of data recovery...» »

  I installed the latest round of updates (Ultimate) of Windows Vista and it apparently burst Netflix in WMC.  Now, I get the error:

  "There was a problem of data recovery. Make sure your internet connection is working and try again. »

  Internet works on the machine.  I reinstalled Silverlight (v4) and Netflix for WIndows Media Center.

  How to diagnose and repair the problem?

  Thank you!

  Keith...

  Sorry for the delay, but I've been busy (in my free time) trying to get this to work.

  I gave up trying to resuscitate MCE and installed a brand new Windows Vista Ultimate Edition with Service Pack 2.  After apply all WIndows patches and installation of Silverlight, I have the "Netflix" element in MCE.  He invites me to install, what I'm doing.  However, every time I start MCE and go to Netflix, he tells me to do reinstall - no login screen.

  I tried all the "mcupdate" article and then supported your steps above, but no go.

  I did this twice, so it wasn't just a fluke.  Apparently, the part of Netflix to MCE is not detect the plug-in that it installed.

  Any thoughts on what to do then?

  Thank you again...

  Keith...

  Later: I ran "mcupdate" after the steps you suggested, and now Netflix is gone again!

  Later: same problem on my other computer running MCE and Vista.  I don't want to mess up this computer so I left as what.

  Later: opening of a new post on problems become Netflix to work with a clean install.

• Failed to load movies Netflix in Media Center message appears to indicate there was a problem of data recovery. Check the works of your internet connection and try again.

  Original title: cannot load Netflix movies in Media Center

  Netflix photo click on the message appears indicating a problem of data recovery.  Check the works of your internet connection and try again.

  Hi Barbarasimonetti,

  (1) since when are you facing this problem?

  (2) remember to make changes?

  (3) what is the complete error message you receive?

  Method 1: You can follow the steps described in the article below

  Known issues and limitations of Netflix on Windows Media Center for Windows Vista

  http://support.Microsoft.com/kb/972496

  Method 2: If a Protection of resources Windows (WRP) file is missing or is damaged, Windows may not behave as expected. Auditor of file system (CFS) scan to fix all of the corrupted system files. To do this, follow the steps mentioned in the link below:

  How to use the System File Checker tool to fix the system files missing or corrupted on Windows Vista or Windows 7

  http://support.Microsoft.com/kb/929833

  Thank you, and in what concerns:

  Ajay K

  Microsoft Answers Support Engineer
  ***************************************************************************

• problem in physical recovery standby database (Data Guard) by rman

  Hi all
  
  I created a physical database Eve, I want to make a backup of it by rman and when I lose datafile is that I can restore, backup and restore is fine, but in recovery I encounter a problem
  scenarios is followed
  
  1. in rman, I create a backup of database Eve by this command:
  backup database more archivelog delete all entries;
  
  2. I run this command in rman to recover standby database
  Run {}
  2 > set up what SNA 1392701.
  3 > restore database;
  4 > restore database;
  {5 >}
  (1392701 is extracted from this query "SELECT MAX (NEXT_CHANGE #) + 1 UNTIL_SCN FROM V$ LOG_HISTORY LH ')
  V$ DATABASE DB WHERE LH. RESETLOGS_CHANGE #= DB. RESETLOGS_CHANGE # AND LH. RESETLOGS_TIME =
  DB. RESETLOGS_TIME; (""http://download.oracle.com/docs/cd/B19306_01/server.102/b14239/rman.htm")
  
  but result RMAN is like this:
  executing command: SET until clause
  
  
  From restoration to 13 December 08
  using channel ORA_DISK_1
  channel ORA_DISK_1: from datafile backupset restoration
  channel ORA_DISK_1: specifying datafile (s) to restore from
  backup set
  restoring datafile 00001 to /u01/app/oracle/oradata/sari/system01.dbf
  restoring datafile 00002 to /u01/app/oracle/oradata/sari/undotbs01.dbf
  restoring datafile 00003 to /u01/app/oracle/oradata/sari/sysaux01.dbf
  restoring datafile 00004 in /u01/app/oracle/oradata/sari/users01.dbf
  restoring datafile 00005 to /u01/app/oracle/oradata/sari/example01.dbf
  restoring datafile to /u01/app/oracle/oradata/sari/users02.dbf 00006
  channel ORA_DISK_1: reading of the backup/home/oracle/backup/0ek24dt4_1_1 element
  channel ORA_DISK_1: restored the backup part 1
  piece handle = / home/oracle/backup/0ek24dt4_1_1
  tag = TAG20081213T042506
  channel ORA_DISK_1: restore complete, duration: 00:01:07
  Finished restoration to 13 December 08
  From back to 13 December 08
  using channel ORA_DISK_1
  starting media recovery
  archive log thread 1 116 sequence is already on the disk that the file /u01/app/oracle/oradata/archive/1_116_666786084.arc
  archive log thread 1 sequence 117 is already on the disk that the file /u01/app/oracle/oradata/archive/1_117_666786084.arc
  Archive newspaper filename=/u01/app/oracle/oradata/archive/1_116_666786084.arc thread = 1 sequence = 116
  Archive newspaper filename=/u01/app/oracle/oradata/archive/1_117_666786084.arc thread = 1 sequence = 117
  Cannot find the log archiving
  archive log thread = 1 sequence = 118
  RMAN-03002: failure of the command recover to 2008-12-13 05:14:13
  RMAN-06054: recovery of media asking unknown journal: thread 1
  SEQ 118 lowscn 1392700
  
  
  3. then I refuse 1392701 to 1392700 and I run this command
  
  Run {}
  2 > set up what SNA 1392700.
  3 > restore database;
  4 > restore database;
  {5 >}
  executing command: SET until clause
  From restoration to 13 December 08
  using channel ORA_DISK_1
  channel ORA_DISK_1: from datafile backupset restoration
  channel ORA_DISK_1: specifying datafile (s) to restore from
  backup set
  restoring datafile 00001 to /u01/app/oracle/oradata/sari/system01.dbf
  restoring datafile 00002 to /u01/app/oracle/oradata/sari/undotbs01.dbf
  restoring datafile 00003 to /u01/app/oracle/oradata/sari/sysaux01.dbf
  restoring datafile 00004 in /u01/app/oracle/oradata/sari/users01.dbf
  
  restoring datafile 00005 to /u01/app/oracle/oradata/sari/example01.dbf
  restoring datafile to /u01/app/oracle/oradata/sari/users02.dbf 00006
  channel ORA_DISK_1: reading of the backup/home/oracle/backup/0ek24dt4_1_1 element
  channel ORA_DISK_1: restored the backup part 1
  total, handle = / home/oracle/backup/0ek24dt4_1_1 tag = TAG20081213T042506
  channel ORA_DISK_1: restore complete, duration: 00:01:08
  Finished restoration to 13 December 08
  From back to 13 December 08
  using channel ORA_DISK_1
  
  starting media recovery
  archive log thread 1 116 sequence is already on record as
  file /u01/app/oracle/oradata/archive/1_116_666786084.arc
  
  archive log thread 1 sequence 117 is already on record as
  file /u01/app/oracle/oradata/archive/1_117_666786084.arc
  
  archive log filename=/u01/app/oracle/oradata/archive/1_116_666786084.arc = 1 thread
  sequence = 116archive log
  filename=/U01/app/Oracle/oradata/archive/1_117_666786084.arc
  thread = 1 sequence = error 117Oracle:
  
  ORA-01547: WARNING: RECOVER succeeded but OPEN RESETLOGS
  would get the below error
  ORA-01152: 1 no file has been restored from a sufficiently old backup
  ORA-01110: data file 1: ' / u01/app/oracle/oradata/sari/system01.dbf'
  
  media recovery complete, duration: 00:00:10
  Finished recover to 13 December 08
  
  
  4. If I run
  Run {}
  restore the database;
  recover the database;
  }
  
  I receive this error on step 2 (06054 RMAN: recovery of media asking unknown journal: thread 1)
  SEQ 118 lowscn 1392700)
  
  5. If I just restore the database and I do not perform a recovery by rman and I restart repeat if applies to all things seem well
  but in the opening of database, I get ORA-01152: 1 file was not restored from a sufficiently old backup
  Ora-01110: data file 1: ' / u01/app/oracle/oradata/sari/system01.dbf' error)
  
  do you know what is the problem
  
  Thank you
  
  Published by: ARKH 12 December 2008 23:06

  This is because as soon as you open the standby database, application of roll forward stops. At least that's true up to 10 gr 2, 11 g, you have the option "Active Dataguard" (requires an additional license), which allows to apply, while the database is open.

  Werner

• problem in the recovery of the database!

  Hi all
  
  I created a new database and wanted to restore the backup to a different database in it, I created the required tablespaces and began the restoration of RMAN backup by
  
  Run {}
  allocate channel 'dev_0' type 'sbt_tape '.
  parms 'ENV = (OB2BARTYPE = Oracle8, OB2APPNAME = orcl OB2BARLIST = DAILY_HISDBS01_ORACLE-DB_ONLINE_5W, OB2BARHOSTNAME = hisdbs01.kfmc.med)';
  Restore controlfile from "c-1179279249-20090511-02';
  change the editing of the database;
  free the channel "dev_0;
  }
  
  The obtained controlfile restored successfully, then I tried to restore and recover the database
  
  Run {}
  allocate channel 'dev_0' type 'sbt_tape '.
  parms 'ENV = (OB2BARTYPE = Oracle8, central = OB2APPNAME, OB2BARLIST = DAILY_HISDBS01_ORACLE-DB_ONLINE_5W, OB2BARHOSTNAME = hisdbs01.kfmc.med)';
  restore the database;
  recover the database;
  free the channel "dev_0;
  }
  
  The restoration was successful, but when I tried to open the database with the resetlogs option
  
  SQL > alter database open resetlogs;
  ALTER database open resetlogs
  *
  ERROR on line 1:
  ORA-01194: file 1 needs a recovery more match
  ORA-01110: data file 1: '+ DATADG/orcl/datafile/system.295.686609187 '.
  SQL > restore database using backup controlfile until cancel;
  
  ORA-00279: change 1136286903 September at 2009-05-11 02:08:22 for thread1
  ORA-00289: suggestion: */arch/archivelog/1_8493_651861624.dbf*
  ORA-00280: change 1136286903 thread 1 is in sequence #8493
  
  Specify the log: {< RET > = suggested |} Filename | AUTO | CANCEL}
  Cancel
  ORA-01547: WARNING: RECOVER succeeded but OPEN RESETLOGS would get below error
  ORA-01194: file 1 needs a recovery more match
  ORA-01110: data file 1: '+ DATADG/orcl/datafile/system.295.686609187 '.
  ORA-01112: media recovery not started
  
  The recovery process is looking for */arch/archivelog/1_8493_651861624.dbf* this archivelog, but this archivelog file is not present at this location, the restore process should have restored all archivelogs as well, in fact any archivelogs didn't get restored, how can I recover the database without newspapers archivelog? It is not possible at all.
  
  Please tell me how can I do the database work?

  Have you tried to restore the Archivelogs through RMAN manually, using "RESTORE ARCHIVELOG FROM TIME ="datestring "?

  See if RMAN can detect the ArchiveLogs tape.

• Database recovery mode recommended

  I have a single Windows Server 2012 running MS SQL 2012 of the machine. This server contains all of our databases for the vCloud infrastructure. From now on, all databases use the recovery model Simple, with the exception of the vCloud Director database that uses the full recovery model. I was wondering what VMware recommends for this database, and if it's ok to switch to Simple mode or not.

  Please let me know.

  Thank you!

  We generally recommend a Simple recovery model, as other modes will tend to newspapers DB fill up quickly.  Full should be good for vCloud Director, except that it's rather talkative, depending on your deployment.

  The other part is that recovery time is difficult because of dependencies on the State of vSphere (if you had to recover as well).

  Backup is not only vCloud, but something else it interacting with in the environment.  If do you still complete and backups of delta for vCloud and vCenter simultaneously, then there is less of a problem.

• VCenter 2.5 Update 1 updated 5 problems with database vim_vcdb

  Hello

  I've recently updated the vcenter 2.5 Update 1 to day 5.  Everything was fine, no problem, but now I have windows event log error messages complaining of the log for the database "VIM_VCDB" is full. To find out why space in the log cannot be reused, see the log_reuse_wait_desc column in sys.databases

  The VIM_VCDB database is set to simple recovery mode.

  My environment is 6 esx servers and 30 virtual machines.  VCenter is led on a physical server using sql express 2005 for the database.

  VIM_VCDB.mdf file size is 640 MB and VIM_VCDB.ldf is 688 MB

  I dropped the log file and it reduces to 1 024 k but after about 30 minutes, he pushes to 688 MB size and I get the error again.

  Any ideas?

  Could you please try to increase the limit more?

  Thank you.

• Open database (recovery) takes too long

  Hello
  Ive been using your great BerkeleyDB Java Edition for a couple of years and have been very happy with it.
  
  I am facing a problem with trying to open the database after a full disk problem (which gave rise to the database is unable to write and therefore not closed).
  
  While recovery seems to work, it took a lot of time - 16 hours so far. My database has data about 200 GB, which has swollen to more than 450 GB during the deletion of entries, so gobble up all the free space on the disk.
  
  My questions are:
  * Should I continue to wait for the recovery?
  * Are there opportunities in loop?
  * Is there an easier way (DBDump?) to extract data from the database without having to perform a recovery?
  
  Other information that can help:
  * The recovery has reduced the size of the last important file and created 3 new files since it started running.
  * I did open (using lsof) files and they change every now and then to other files, but a good amount of his time came near the end of the database.
  
  So, I feel like recovery runs normally just takes too long. Please let me know your opinion.
  
  A few other things I should mention about my question:
  * The database was, until yesterday, running on java bdb 3.3.75. After several hours of recovery, I upgraded to 4.1.10 (since I read about a possible recovery loop bug in one of the versions)
  * Once 4.1.10 began recovering, he spat errors on the last 2 files. Only on deleting those 2 files (the latter being 0 bytes, the 2nd last one being about 5 k) made the beginning of recovery. Note that the recovery 3.3.75's longer never complained about these files. I can post errors here as appropriate.
  * Some files jdb (about 500 cases of the 47 000 files that make up the database) are files of 100 MB, because I had experienced with files of larger sizes for a few days, then returned the setting.
  
  All these above would affect a successful recovery?
  
  
  My configuration is:
  OS: Linux CentOS 5.2, 64-bit, kernel 2.6.18 - 92.el5
  JVM: Sun Java 1.6.0_20, 64-bit
  Memory: 16 GB of RAM, including 8 GB is allocated to the java process (- Xmx8000M - Xms8000M)
  Cache of BDB for use 6 GB of RAM (envconfig.setCacheSize (6000000000))
  
  Only the basic BDB API is to be used (environment, data, the sliders). We do use DPL, or HA features.
  
  Waiting for your kind response,
  Sushant has
  

• HP Pavilion DV6 6140 TX: Problem of HP Recovery Manager in Windows 10

  After the upgrade to windows 10 windows 7, HP Recovery Manager does not work. Whenever I open it, it says: "an administrator blocked you execution of this application. How can I solve this problem? Any help is appreciated. Thank you

  Hello

  Recovery Manager for Windows 7 will not work on an improved version of Windows 10. You must use the Windows 10 tool

  http://Windows.Microsoft.com/en-AU/Windows-10/Windows-10-recovery-options

  Concerning

• Equium L100 - problems of product recovery

  Hello

  Im having serious problems trying to run a recovery of product on my laptop Equium L100.

  I restarted the laptop using the recovery disk of the supplied product as described in the user manual and after the re-installation of the drivers of the laptop turns off automatically. I presume it was part of the recovery procedure, and so turned the laptop, to find that, after the Welcome screen, the monitor shows a black screen, hence there is no progress.

  I don't know what I can do from this point. I assumed that all the data to the origin of the laptop was dropped, but the laptop does not restart properly and stays on the black screen. Any help that anyone can provide me to complete the process of reformatting would be much appreciated.

  Thank you very much

  James

  Hello James

  There's not a trick to get it working again. Either it works or not.
  Please try to make the installation of recovery once more. Before that, set the BIOS to default settings and launch the installation of recovery.

  When the installation is complete, remove the optical drive installation disc and restart your laptop to see if the same thing will happen again.

• Satellite C670D-121 - problems with Win7 recovery

  I have a problem and I need your help.

  I have a laptop Satellite C670D-121 in the original hardware configuration.

  After a message on a process (my 10 year old son told me. "" But I have not seen this message), press the OK button and then the cell phone has rebooted. "
  But restarting didn't work no more.

  Also the recovery with the recoveryfunction of the laptop was not possible.
  Now, I ordered the UDF of recovery and the restoration of the laptop is possible.

  But in the moment where the UDF must be removed and the laptop should be repeated, I see the letters "Start window", the screen goes black and I can only see the cursor.

  After a short time, the cursor jumps into the upper left corner. And then comes the whith window an error message. (s. picture)

  I ordered a new UDF = the same error recovery!
  Support couldn't help me.
  Boot Linux from the CD, the laptop works very well.

  If a HARD disk error and memory can be excluded.
  [photo s | http://www.dienagelschmiede.com/win.jpg]

  Can someone help me please?
  Thank you.

  Hello
  I m not quite about this error message, but it seems that s associated with memory issue I/O (input / output).

  You mentioned a cursor blinking in the upper left corner.
  This symptom is already known to me. I had such a problem blinking cursor also and in my case it was related to abnormal or bad memory and HARD drive.
  I had to replace the HARD drive after all firstly by the modules of memory in order to solve this problem.

  From my point of few your question may be linked to the faulty memory because the I/O message is linked to problems of memory too.

  You said that Linux works properly using the Live CD?
  I guess you booted the laptop using this live cd but did not install the system on the HARD disk.
  Well, I don t think that this could be a clear proof that the RAM or HARD drive is OK.

  In my opinion, these parts must be checked