Problem of routing in PIX 515E

Similar Questions

• Problem of NAT with PIX 515E

  I configured a PIX 515E, OS 7.0 (1) f? PAT r dynamic of the inside of the network to the external ip address of the PIX. I also configured for icmp access lists from inside to outside and inside. All traffic (www, dns, ftp, etc.) works very well except ping. Whenever I do a ping from host inside to any address outside, I get the following error messages:

  6. August 24, 2006 11:10:52 | 609002: duration of disassembly-outside local host: 193.222.224.104 0:00:10

  6. August 24, 2006 11:10:52 | 302021: connection of disassembly ICMP for faddr gaddr laddr 8994/FDFR001 212.203.90.59/9 193.222.224.104/0

  6. August 24, 2006 11:10:50 | 302021: connection of disassembly ICMP for faddr 193.222.224.104/0 gaddr 212.203.90.59/8 laddr FDFR001/8993

  4. August 24, 2006 11:10:50 | 106023: Deny icmp src, dst outside: 193.222.224.104 inside: 212.203.90.59 (type 0, code 0) by access-group "outside_access_in".

  6. August 24, 2006 11:10:50 | 302020: ICMP connection built for faddr gaddr laddr 8994/FDFR001 212.203.90.59/9 193.222.224.104/0

  6. August 24, 2006 11:10:48 | 302021: connection of disassembly ICMP for faddr 193.222.224.104/0 gaddr 212.203.90.59/7 laddr FDFR001/8992

  4. August 24, 2006 11:10:48 | 106023: Deny icmp src, dst outside: 193.222.224.104 inside: 212.203.90.59 (type 0, code 0) by access-group "outside_access_in".

  6. August 24, 2006 11:10:48 | 302020: ICMP connection built for faddr 193.222.224.104/0 gaddr 212.203.90.59/8 laddr FDFR001/8993

  6. August 24, 2006 11:10:46 | 302021: connection of disassembly ICMP for faddr 193.222.224.104/0 gaddr 212.203.90.59/6 laddr FDFR001/8991

  4. August 24, 2006 11:10:46 | 106023: Deny icmp src, dst outside: 193.222.224.104 inside: 212.203.90.59 (type 0, code 0) by access-group "outside_access_in".

  6. August 24, 2006 11:10:46 | 302020: ICMP connection built for faddr 193.222.224.104/0 gaddr 212.203.90.59/7 laddr FDFR001/8992

  6. August 24, 2006 11:10:44 | 302021: connection of disassembly ICMP for faddr 193.222.224.104/0 gaddr 212.203.90.59/5 laddr FDFR001/8990

  4. August 24, 2006 11:10:44 | 106023: Deny icmp src, dst outside: 193.222.224.104 inside: 212.203.90.59 (type 0, code 0) by access-group "outside_access_in".

  6. August 24, 2006 11:10:44 | 302020: ICMP connection built for faddr 193.222.224.104/0 gaddr 212.203.90.59/6 laddr FDFR001/8991

  4. August 24, 2006 11:10:42 | 106023: Deny icmp src, dst outside: 193.222.224.104 inside: 212.203.90.59 (type 0, code 0) by access-group "outside_access_in".

  6. August 24, 2006 11:10:42 | 302020: ICMP connection built for faddr 193.222.224.104/0 gaddr 212.203.90.59/5 laddr FDFR001/8990

  6. August 24, 2006 11:10:42 | 609001: built outside local host: 193.222.224.104

  What could be the problem?

  Thank you, Meg

  It's only to predict the responses of echo at all on the external interface. If you do the following ACL on the outside, it should work...

  outside_access_in list extended access permit icmp any any echo response

• PIX 515E configuration problems

  I have a UR PIX 515 (6.3.2 os) that works really well, so I copy the configuration on my new PIX 515E-R (os 6.3.2). The PIX 2 have exactly the same configuration. But when I use the PIX 515E-R, I have some problems with the PIX 515E r only

  -I can't access the Internet, but I can ping the router Internet of my PIX 515E. The problem, in my view, must be with the Internet router, not on my external interface.

  -J' have a similar problem with my DMZ. I can ping to the DMZ, a frame relay router interface, but I can't pass this router.

  Is it possible that PIX 515E-R is not compatible with the router? and not the PIX 515 HEART?

  Thanks for your replies.

  Hello

  Just a thought, try clearing the PRA of table on the router and see what happens. Let me know if it helps.

  Jay

• IPSEC VPN between Pix 515E and 1841 router

  Hi all

  BACKGROUND

  We have implemented a site to site VPN IPSEC between a Pix 515E 8.0 operation (4) and an 1841 using static IP addresses at both ends. We used CCP on the router and the ASDM the pix to build initial tunnels. Now the site with the router is evolving into a dynamic IP address from the ISP so we have implemented dynamic DNS to update dynamic IP address.

  PROBLEM

  The problem is that ASDM will not allow us to set a domain as the address of peers, it will not accept an IP address. We believe that the solution will be to remove the static Crypto map and replace it with a dynamic Crypto map on the side of Pix. Our questions are simply; is this the best solution? can change us the original static list or is it better to delete and make a new dynamic encryption card? Y at - it a shortcut to change the config command-line? This is a real network, so just check it out before make us any changes on the live kit.

  Any help much appreciated.

  You don't have to change anything when the peer-address changes. The dynamic crypto map aims to take dynamic peer connections. The only thing to remember, is that only the dynamic peer can initiate the connection. And you reduce your security if you use Pre-Shared key that now you can use a generic-PSK character.

  As I remember, the PIX / ASA does not support the dynamic use of FQDNs for peer-resolution. This feature is supported in IOS.

  For a feature, it would be preferable to static IP addresses on both sides.

• problems after Pix 515e of 6.34 to 7.12

  Recently upgrade a PIX 515e of 6.34 to 7.12. Everything seemed to work well, but having a problem of access to certain web sites. Basically, allow us all IP from the "inside" network traffic Log errors are:

  609001: built outide:199.230.128.100 local-home

  106015: TCP (no relation) to deny djm/1646 199.230.128.100/80 flags ACK on the interface inside

  609002: dismantling of the local-host ouside: 199.230.128.100 duration 0:00:00

  Config is attached...

  We also find that the problems on the same platform. Have removed the inspection of HTTP the default control as a temporary workaround rule:

  Policy-map global_policy

  class inspection_default

  don't inspect http

  Still looking for a solution...

• VPN - Pix 515e for Cisco router

  I have the following Setup and I can't seem to get the next tunnel. My end is a PIX 515e race 7.2 (4). The other end is a Cisco router-not sure of the model or version of the IOS.

  PIX:

  90 extended access-list allow ip host a.a.a.a host b.b.b.b

  NAT (inside) - 0-90 access list

  correspondence address card crypto mymap 20 90
  card crypto mymap 20 peers set x.x.x.x
  map mymap 20 set transformation-strong crypto
  mymap outside crypto map interface
  ISAKMP crypto identity hostname
  crypto ISAKMP allow outside
  crypto ISAKMP policy 8
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 86400

  tunnel-group x.x.x.x type ipsec-l2l
  tunnel-group ipsec-attributes x.x.x.x
  pre-shared key 12345

  Router:

  / * Style definitions * / table. MsoNormalTable {mso-style-name : « Table Normal » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-qformat:yes ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 à 5.4pt 0 à 5.4pt ; mso-para-margin : 0 ; mso-para-marge-bottom : .0001pt ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-fareast-font-family : « Times New Roman » ; mso-fareast-theme-font : minor-fareast ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ; mso-bidi-font-family : « Times New Roman » ; mso-bidi-theme-font : minor-bidi ;} / * Définitions de style * / table. MsoNormalTable {mso-style-name : « Table Normal » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-qformat:yes ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 à 5.4pt 0 à 5.4pt ; mso-para-margin : 0 ; mso-para-marge-bottom : .0001pt ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-fareast-font-family : « Times New Roman » ; mso-fareast-theme-font : minor-fareast ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ; mso-bidi-font-family : « Times New Roman » ; mso-bidi-theme-font : minor-bidi ;}

  SDM_5 extended IP access list

  permit ip host b.b.b.b host a.a.a.a

  ISAKMP crypto key 12345 address y.y.y.y no.-xauth

  map SDM_CMAP_1 5 ipsec-isakmp crypto

  Description vpn for laboratory

  defined peer y.y.y.y

  game of transformation-ESP-3DES-SHA

  match address SDM_5

  I'm running him debugs following:

  Debug crypto ipsec enabled at level 1
  ISAKMP crypto debugging enabled at level 1

  I get the following debug output:

  August 16-04:16:10 [IKEv1]: IP = x.x.x.x, counterpart of drop table counterpart, didn't match!
  August 16-04:16:10 [IKEv1]: IP = x.x.x.x, error: cannot delete PeerTblEntry

  Isa HS her

  IKE Peer: x.x.x.x
  Type: user role: initiator
  Generate a new key: no State: MM_WAIT_MSG2

  Any ideas?

  Thank you

  Dave

  If you see the MM_WAIT_MSG2, which means that her counterpart (the other side) does not answer and this side where you can see the status MM_WAIT_MSG2 sent the first message IKE, however, did not hear of the peer.

  You can check if UDP/500 is stuck on the way between the 2 sites.

  Try running traffic on the other side and see if you also get the same status of MM_WAIT_MSG2. If you do, that confirms 100% 500/UDP is blocked on the way between the 2 sites.

• PIX 515E - VPN connections

  Hello

  I have pix 515E and I configured a VPN on it. My users connect to my network from the internet via the Cisco VPN client.

  I have problem, only their LAN machine can do VPN from Cisco VPN client to my network at once.

  Users are connected to the internet via an ADSL router and the LAN switch.

  --------------------------------------------------

  PIX Config:

  6.3 (4) version PIX

  interface ethernet0 car

  Auto interface ethernet1

  ethernet0 nameif outside security0

  nameif ethernet1 inside the security100

  enable encrypted password xxxxxxxxxxxxxxx

  xxxxxxxxxxxxxxxx encrypted passwd

  hostname ABCDEFGH

  ABCD.com domain name

  clock timezone IS - 5

  clock to summer time EDT recurring

  fixup protocol dns-length maximum 512

  fixup protocol ftp 21

  fixup protocol h323 h225 1720

  fixup protocol h323 ras 1718-1719

  fixup protocol http 80

  fixup protocol rsh 514

  fixup protocol rtsp 554

  fixup protocol sip 5060

  fixup protocol sip udp 5060

  fixup protocol 2000 skinny

  fixup protocol smtp 25

  fixup protocol sqlnet 1521

  fixup protocol tftp 69

  inside_out to the list of allowed access nat0_acl ip 192.168.1.0 255.255.255.0 192.168.2.0 255.255.255.0

  list of allowed shared access ip 192.168.1.0 255.255.255.0 192.168.1.0 255.255.255.0

  pager lines 24

  Outside 1500 MTU

  Within 1500 MTU

  IP address outside xxx.xxx.xxx.xxx 255.255.255.0

  IP address inside 192.168.1.1 255.255.255.0

  alarm action IP verification of information

  alarm action attack IP audit

  IP local pool vpnpool 192.168.2.1 - 192.168.2.254

  PDM logging 100 information

  history of PDM activate

  ARP timeout 14400

  Global interface 10 (external)

  NAT (inside) 0-list of access inside_out-nat0_acl

  NAT (inside) 10 0.0.0.0 0.0.0.0 0 0

  Route outside 0.0.0.0 0.0.0.0 xxx.xxx.xxx.xxx 1

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225

  H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00

  Timeout, uauth 0:05:00 absolute

  GANYMEDE + Protocol Ganymede + AAA-server

  AAA-server GANYMEDE + 3 max-failed-attempts

  AAA-server GANYMEDE + deadtime 10

  RADIUS Protocol RADIUS AAA server

  AAA-server RADIUS 3 max-failed-attempts

  AAA-RADIUS deadtime 10 Server

  AAA-server RADIUS (inside) host ABCDE timeout 10

  AAA-server local LOCAL Protocol

  RADIUS protocol radius AAA-server

  Radius max-failed-attempts 3 AAA-server

  AAA-radius deadtime 10 Server

  RADIUS protocol AAA-server partnerauth

  AAA-server partnerauth max-failed-attempts 3

  AAA-server deadtime 10 partnerauth

  partnerauth AAA-server (host ABCDEFG myvpn1 timeout 10 Interior)

  Enable http server

  http 192.168.1.0 255.255.255.0 inside

  No snmp server location

  No snmp Server contact

  SNMP-Server Community public

  No trap to activate snmp Server

  enable floodguard

  Permitted connection ipsec sysopt

  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto-map dynamic outside_dyn_map 20 the transform-set ESP-3DES-MD5 value

  map outside_map 65535-isakmp ipsec crypto dynamic outside_dyn_map

  card crypto client outside_map of authentication partnerauth

  outside_map interface card crypto outside

  ISAKMP allows outside

  ISAKMP key * address 0.0.0.0 netmask 0.0.0.0

  ISAKMP identity address

  part of pre authentication ISAKMP policy 8

  ISAKMP strategy 8 3des encryption

  ISAKMP strategy 8 md5 hash

  8 2 ISAKMP policy group

  ISAKMP life duration strategy 8 the 86400

  part of pre authentication ISAKMP policy 10

  ISAKMP policy 10 3des encryption

  ISAKMP policy 10 sha hash

  10 2 ISAKMP policy group

  ISAKMP life duration strategy 10 86400

  vpngroup myvpn address vpnpool pool

  vpngroup myvpn ABCDE dns server

  vpngroup myvpn by default-field ABCD.com

  splitting myvpn vpngroup split tunnel

  vpngroup idle 1800 myvpn-time

  vpngroup myvpn password *.

  Telnet 192.168.1.0 255.255.255.0 inside

  Telnet timeout 5

  SSH timeout 5

  Console timeout 0

  dhcpd address 192.168.1.200 - 192.168.1.254 inside

  dhcpd dns ABCDE

  dhcpd lease 3600

  dhcpd ping_timeout 750

  field of dhcpd ABCD.com

  dhcpd outside auto_config

  dhcpd allow inside

  Terminal width 80

  --------------------------------------------------

  Thanks in advance.

  -Amit

  Try to add the "isakmp nat-traversal" command to your PIX. I suspect what happens is that Remote LAN users is translated to a single IP address as they pass through the DSL connection. I also assume that the machine doing the translation has a capacity of IPSec passthrough. Linksys routers would be a good example of this type of NAT device that allows IPSec pull-out.

  If that's the case, that a single VPN connection will be able to operate both. The above command will turn PIX detect clients that are located behind a NAT device, and then try to configure the VPN sessions in UDP packets and so to work around the limitation of NAT and IPSec passthrough device.

• PIX 515E v7 VPN config help

  Hello

  I have a PIX 515E current of execution to 7.

  Is it possible to use VPN with only 1 static IP address from the ISP (no gateway or the ip address of the ISP router is provided).

  I can set up routing on the ADSL modem, but then the PIX does not have a valid Internet IP address?

  I think that v7 does not support PPPOE? so I can't set the mode on the bridged adsl modem?

  Is there a way to fix this?

  Any help appreciated gratefully.

  apply the commands below:

  ISAKMP identity address

  ISAKMP nat-traversal 20

  If the problem persists, then please post the entire config with ip hidden public.

• Cisco VPN Client Authentication - PIX 515E-UR

  Hi all

  I need your expert help on the following issues I have:

  1. I would like to create more than 1 client VPN on my PIX-515E groups. This is so that I can give a different part of the internal network access to different type of VPN connection. For example, I want a group to have no XAUTH, while the other group must use RADIUS XAUTH. Is it possible for me to do this? I see the PIX automatically enable RADIUS on both groups of VPN clients.

  2. the RADIUS server is a Microsoft ISA with IAS server and it is located on the PIX inside interface. The VPN endpoint is external interface of the PIX. Is there a problem with this Setup? Do I need to have the RADIUS server that is located on the external interface?

  3 can. what command I use to debug RADIUS authentication?

  Thanks in advance for your help.

  Hi vincent,.

  (1) you can use the vpngroup *-authentication server ipaddress to specify the IP address of the Radius Server on a particular group... If you do not specify this, the authentication of the user is made locally... also check for vpngroup * order of user authentication

  (2) there should be no problem with the installation of your... should work fine... If the RADIUS is outdoors, it is subject to many attacks... so have it inside...

  (3) use the "RADIUS session debug" or "debug aaa authentication..."

  I hope this helps... all the best... the rate of responses if found useful

  REDA

• PIX 515E for VPN remote site

  Hello

  7.0 (1) version pix

  ASDM version 5.0 (1)

  I have a situation where you go paas-thanks to the VPN feature goes on our PIX 515E. I tried to put this on the pix using a VPN Wizard Site to site

  who is enabled. I was unable to connect to the pix from the remote site. Witch's journal replied negotiate the pix is OK and the success

  The problem is when I try to set up the tunnel to the top of the remote site. I fall without failure.

  where can I see the vpn pix for error log?

  is there a manual for the solution of site to site VPN using the wizard

  Help, please.

  Thanks in advance

  http://www.Cisco.com/en/us/partner/products/HW/vpndevc/ps2030/products_configuration_example09186a00804acfea.shtml#ASDM

  the section 'use adsm' (step 14) gives an example on how to set up vpn lan - lan via adsm

  Newspaper to go to the section "check".

• Question of PIX 515E

  Hi all

  We just bought a PIX 515E and try to use it, but got a number of questions. Here's the NVA of show:

  PIX-151st #show version

  Cisco PIX Firewall Version 6.3 (1)

  Cisco PIX Device Manager Version 3.0 (1)

  Updated Thursday 19 March 03 11:49 by Manu

  PIX-515E up to 5 hours and 15 minutes

  Material: PIX-515E, 64 MB RAM, Pentium II 433 MHz processor

  Flash E28F128J3 @ 0 x 300, 16 MB

  BIOS Flash AM29F400B @ 0xfffd8000, 32 KB

  0: ethernet0: the address is 000f.2457.4b12, irq 10

  1: ethernet1: the address is 000f.2457.4b13, irq 11

  Features licensed:

  Failover: enabled

  VPN - A: enabled

  VPN-3DES-AES: enabled

  Maximum Interfaces: 6

  Cut - through Proxy: enabled

  Guardians: enabled

  URL filtering: enabled

  Internal hosts: unlimited

  Flow: IKE peers unlimited: unlimited

  This PIX has a failover license only (FO).

  Problem is that we cannot ping inner harbor, if we do not switch light, but this is a unique machine. Here's another message once we turn on the switch:

  PIX-515E # config t

  WARNING *.

  Configuration of replication is NOT performed the unit from standby to Active unit.

  Configurations are no longer synchronized.

  PIX-515e (config) #.

  Please help solve this problem. I wonder if we buy the wrong license? Thank you very much.

  you have in your possession a PIX failover. That's why says in the "sh run".

  This device is intended to be used only as a failover for a live device. It will work as a live PIX, but behave badly. It is cheaper than a PIX with an unrestricted license, as it is not intended to be used as a standalone device. Check with the one that you bought to get the situation sorted.

  Good luck

  Steve

• ASDM 5.02 on PIX-515E

  When I use ASDM to administer my PIX-515E (v7.0), I get messages from 2 following error if I update the screen after being inactive in the session for about 2-3 minutes about:

  Error message 1

  ASDM is temporarily unable to communicate with the firewall.

  Error message 2

  ASDM is unable to reach the PIX. Please check the configuration and your connection and try again by clicking the Refresh button.

  These messages were recently and I don't know why. Is there an ASDM idle session time-out setting? I could not found.

  Thank you

  Bill Fanning

  Hello

  What version of Java are you using. If you have Java 1.6, can you go back to 1.5 and see if the problem goes away.

  Also, here is the URL indicating the operating system for client PC and browser requirements

  http://www.Cisco.com/en/us/partner/docs/security/ASA/asa70/asdm50/release/notes/RN505.html#wp231810

  I hope it helps.

  Kind regards

  Arul

  * Please note all useful messages *.

• PIX 515e Install

  I am installing a PIX 515e with an ADSL router. I have all the IP addresses for the router etc. I'm trying to connect to a network on the interface internal of the PIX. (Please bare with me as I am new on the firewall!)

  I ping the network firewall, but I can not access to the internet. The initial configuration for the PIX documentation implies that by default, it has access form the firewall but no! I'm obviously missing something here, i.e. of Thompson the network to route requests through the firewall interent! ???

  Sorry to be so simplistic but I'm learning all the time!

  Thanks for any help.

  Robin

  After you enter the acl to allow ping, can you ping now?

  Watch newspaper reveal something?

  For DNS and testing, create a static on the PIX for your DNS server. For example "x.x.x.x (indoor, outdoor) static 192.168.0.x netmask 255.255.255.255" where x.x.x.x is a public IP address and 192.168.0.x is your dns server. Then let the outside to your DNS server dns - "access-list 101 permit host udp/tcp host x.x.x.x eq 53 z.z.z.z ' where z.z.z.z is a public dns server (or use one for testing) and x.x.x.x IP NAT'ed to your dns server. See what is happening, look in your journal.

  What version of PIX you run.

  Let know use.

  Steve

• Using PIX 515E configuration require

  Dear all,

  Hi.Actually I need help for PIX 515E.Pls. check out the scenario, design & suggest?

  Pls. find the details following and configuration of VLAN attached router.

  # I want to put as

  «Spend my LAN on CISCO 2900 (range 172.16.29.X IP...» (25 PCs) - VLAN router - CISCO PIX - ISP public IP.

  # Now it's

  "My LAN on CISCO 2900 - VLAN (external) router - ISP.

  Details of router & PIX:

  #Router inside the IP - 172.16.29.1 (inside property intellectual as it is very critical that cannot be changed)

  Outdoor #Router ip - what ip should I use? (I tried with 1.1.1.1 255.255.255.0)

  #PIX outside intellectual property - what ip should I use? (My ISP IP?-j' tried with 208.144.230.197 which is currently outside of my router)

  #PIX within the intellectual property - what ip should I use? (I tried with 1.1.1.2 255.255.255.0)

  Connection ISP #My is directly from the ISP GW to an ethernet cat 5 on my router VLAN

  #I would allow www, FTP, web-based like Yahoomail... etc... & Messenger services

  VLAN router Config:

  Current configuration: 1028 bytes

  !

  version 12.3

  horodateurs service debug datetime msec

  Log service timestamps datetime msec

  no password encryption service

  !

  hostname VLANRouter

  !

  boot-start-marker

  boot-end-marker

  !

  activate the gcsroot password

  !

  No aaa new-model

  IP subnet zero

  !

  !

  no record of conflict ip dhcp

  DHCP excluded-address IP 172.16.29.1 172.16.29.240

  DHCP excluded-address IP 172.16.29.250 172.16.29.254

  !

  IP dhcp pool dhcppool

  network 172.16.29.0 255.255.255.0

  DNS-server 208.144.230.1 208.144.230.2

  router by default - 172.16.29.1

  !

  !

  !

  !

  controller E1 0/0

  !

  controller E1 0/1

  !

  !

  interface FastEthernet0/0

  IP 208.144.230.197 255.255.255.224

  NAT outside IP

  automatic duplex

  automatic speed

  !

  interface FastEthernet0/1

  IP 172.16.29.1 255.255.255.0

  IP nat inside

  automatic duplex

  automatic speed

  !

  IP nat inside source list 7 interface FastEthernet0/0 overload

  IP http server

  IP classless

  IP route 0.0.0.0 0.0.0.0 208.144.230.200

  !

  !

  access-list 7 permit 172.16.29.0 0.0.0.255

  !

  Line con 0

  line to 0

  line vty 0 4

  opening of session

  !

  !

  !

  end

  All advice is appreciated.

  Kind regards

  Hiren s Mehta.

  ORG Informatics Ltd.

  Bamako, MALI

  AFRICA

  Hi hiren,.

  See the answers below:

  #Router inside the IP - 172.16.29.1 (inside property intellectual as it is very critical that cannot be changed)

  When you upgrade the PIX router inbetween and your switch, you must put the PIX inside IP like 172.16.29.1 and change the router within the subnet to someother pool. Do the PAT on the PIX, rather than the router.

  Outdoor #Router ip - what ip should I use? (I tried with 1.1.1.1 255.255.255.0)

  Router outside the property intellectual property will be that given by the ISP... The ISP would have given a public IP address for the WAN link. This cannot be changed.

  #PIX outside intellectual property - what ip should I use? (My ISP IP?-j' tried with 208.144.230.197 which is currently outside of my router)

  PIX outside IP must be comprehensive. ISP would have given you a LAN subnet. Use it. In this case, inside the interface of the router has an IP address from that subnet even...

  #PIX within the intellectual property - what ip should I use? (I tried with 1.1.1.2 255.255.255.0)

  PIX inside must be 172.16.29.1, which will be the default gateway for all PCs. If you change this subnet, then the PC should have an IP address on the same subnet that has decided.

  Connection ISP #My is directly from the ISP GW to an ethernet cat 5 on my router VLAN

  didn't get it... is that on the internet router or switch?

  #I would allow www, FTP, web-based like Yahoomail... etc... & Messenger services

  If all these must be permitted from inside to outside, you have not open anything... by default, all traffic to the inside outside is allowed (except if you put a list of access denied)...

• PIX 515E failover recover

  I have two PIX 515E firewall v7.01 configured in a failover scenario.

  The two units were operating without problem. Primary worked very well and the configuration changes have been transferred to secondary school.

  By TAC support, the only thing needed to test the failover was to issue a command to 'reload' in the primary and the secondary, take on main. Then, "active failover" question on the once rebooted device it was up in the secondary role.

  Failover to the secondary unit worked without problem, it is a smooth transition to the secondary unit.

  The problem came in that the original primary unit is stuck in a loop when you try to reload with what looks like now configuration errors. It will not properly start upward.

  Is not a valid procedure to test the failover?

  It seems that in the real world, this could actually happen that failover should work?

  Among what is shown:

  Config ERROR: invalid journal / level keyword specified; level must be emergencies (0) - debugging (7)

  Config error - acl_in list extended access permit tcp any newspaper SMTP host 208.13.32.36 eq

  Out of config line 359, "access-list acl_in exten...". »

  Config sync error: Suite not command could be executed in standby mode

  Platform

  acl_in list access permit tcp any host 208.13.32.36 eq smtp log inactive

  Use BREAK or ESC to interrupt boot.ridge/vlan/modify flash): m

  e inactivea VLAN

  REPLICATION OF CONFIGURATION OF ACTIVE TOWARDS THE RESCUE UNIT IS INCOMPLETE,

  Reading of 115200 bytes of the image of the flash.

  TO AVOID THE EVE OF TAKING OVER AS ACTIVE WITH A PARTIAL CONFIGURATION UNIT, THE EMERGENCY UNIT WILL NOW RESTART *.

  You're not going to like this answer.

  It seems that commands typed in and abstract by cisco in the configuration are not valid when copied/pasted in or when the firewall is rebooted or receives an active firewall configuration.

  I don't know exactly what you did, but here's what I did to reproduce your problem:

  I typed in the command:

  acl_in list access permit tcp any host 208.13.32.36 eq smtp interval 300 inactive information newspaper

  Given that "interval 300 ft newspaper is the default, it is actually saved in the running-config like:"

  acl_in list access permit tcp any host 208.13.32.36 eq smtp log inactive

  It's * not * a command invalid (the word "journal" following address must be a logging level), if you try to kick it. When you restarted the firewall, he tried to shoot the active configuration of the device (because it is now pending), received this line and since he can't run it (because it is not a valid command), it keeps restarting itself so that it cannot take over and be the active firewall.

  Best way to do is to hold this line (and other lines like him) outside the firewall active now - the line is marked "inactive" in any case, this should not affect you. The other way would be to change that line to something by default (the recording level change may be easier). In this way when the primary/secondary itself restarts again, the order received will have a valid log level (or if you take the lines out, they will not be a problem) and will allow the rest of the configuration process.

  You can also report to cisco as a bug, if they are not combing these forums already.

  -Jason

  This rate if this can help.