problem of SCB - 68

Similar Questions

• SMU 6341 and SCB-68: problem with several entries... * URGENT *.

  Hello

  I have an urgent problem, I would really appreciate help with.

  I have a terminal block (SCB-68) connected to a multifunction data acquisition (6341). There are 4 entries in the Terminal:

  1 sensor laser displacement, coming from a controller as a signal of analog voltage output ("1V" and "0V" on the controller). Connected to AI 0 and GND.

  2. The accelerometer (PKI, coming from a then the voltage signal conditioner) connected to GND AI and AI 10.

  3 load cells (PKI, coming from a then the voltage signal conditioner) connected to AI 11, 12, 13 and 14, each connected to the GND PIN is close.

  Problem:

  By MAX, if I read in 6 channels above my data acquisition (6341), my displacement sensor (#1) and the accelerometer (#2) behave very well. However, among the channels (AI 11 and AI 12) load cell switch in tension, as if they follow the movement sensor voltage (#1). For example, there is usually a mV - 800 in AI 11 voltage change.

  This problem disappears when I'm not reading travel (HAVE 0, #1) laser. that is as soon as I remove this channel of my task, the readings of cell and accelerometer support back to normal (base voltage ~ 0V). Yet once if I ask again the laser channel, I see a vertical movement in the readings of load cell 2 (displacement varies with the current tension HAVE 0).

  Attempts of fixation:

  -tried to change the differential using AI laser sensor 0 and AI 9

  -tried to delete the field of laser 120V Power

  Any ideas at all would be greatly appreciated!

  SCB-68:

  http://sine.NI.com/NIPs/CDs/view/p/lang/en/NID/1180

  SMU-6341:

  http://sine.NI.com/NIPs/CDs/view/p/lang/en/NID/207415

  This is the general idea.  If you must use high impedance sources and that you have enough channels available, placing a channel of the grounding of entry between each other usually helps.  You must analyze these chains grounded.  Just grounded isn't them enough.

  Example: Sensor has = AI0, ground = AI1, sensor B = AI2, ground = AI3, sensor C = AI4, AI5 = ground.  Read AI0:5.

  Lynn

• SCB 68 rigged with potentiometer, have problems...

  [I am preparing a graduate in the laboratory material that I work so much that I apologize in advance if I misuse of terminology, I'm not quite familiar with it]

  I have a SCB-68 block connected to a computer through a PCI-6289.  I can see the device in MAX and he claims an automatic test.

  I'm trying to wire two 5V linear potentiometers in the block.  Right now, I have the one with the power and return the wires in the terminals of screws 68 and 67, which tells me that the pinout diagram are AI0 and AIGND.  The potentiometer should vary from ~ 0V full extension to 5V to complete removal.  Instead, run a test on results AI0 massive fluctuations not correlated randomly.

  Another question here suggested he switch to A1, I did, but no other results so I moved them back.

  Someone has any advice on how wire properly this configuration?  Thank you.

  Problem solved.  It turns out that the problem was because I was in differential mode, I needed to have the two wires on the pot in two separate channels.  Hang them up to AI1 and AI9, everything works as it should.  Logic wants future pots can be added in channels 2-10, 3-11 and so on.

  Thanks for the help.

• Problems to use two scb-68 has the NI PXI-6225

  Dear nor Forum,.

  I have a chassis NI SMU-1078, with embended OR PXIe8135 controller. One of the slot is busy with a PXI-6225. I for a long time successfully using 1 connection SCB-68 block a with the PXI-6225. Now, I need another channel to analog output on top of OD uses two that I am current. I plugged another SCB-68 connector Panel at the PXI6225, but I could not see analog outputs on this second bedroom. I could not see more channels to DAQmx AO create channel VI

  The PXI-6225 has only 2 analog outputs.  The second connector only has analog inputs.

  If you need more than output analog, you can take a look at the SMU-6738, which includes 32 analog outputs.

• PCIe-7842r to SCB-68 has

  Hello

  I brought a PCIe-7842r, and it comes with the SCB, 68 a, as the connection block.

  I want to use the connection block for analog and digital output entry, so I plugged the pin68 and PIN 67 with two sons. 68 pin and PIN 67 on SCB68A is to HAVE it + and I-on the PCIe 7842r too, so it fits perfectly.

  Next step, I want to use the PCIe 7842r to a digital output, and I intend to use the 36 pin and pin 2, which corresponds to DIO0 and DGND.

  However, pin 36 and on the SCB68A pin2 is DGND and PFI14, which does not match the result of the PCIe 7842r.

  Y at - it suggestions for dealing with this problem?

  Best,

  Matthew

  MatthewTang wrote:

  On page 9, you will need to enlarge to see the label

  If you look at the label on this page closely, you will see that it is for M and X Series DAQ devices.  You must read the section on the use of the SCB-68 has as a Feedthough Direct (page 14) and use the code I linked at the earliest for the R series card.

• 6509 PXI and SCB 100 Port 0 and 3 Port have lines that are high

  Hello

  I work with a PXI-6509 connected to an SCB-100.  When I run the test panels lines 0,1,2 are high on port 0.  0,1,2,3 lines are high on port 3.

  I have a voltage of 3 volts measured between Port0 line 0 and Gnd (PIN 47 and PIN 50).  Nothing is connected to my SCB-100.

  I put the switches for the recommended positions for Digital passthrough.

  SW1, SW2, SW3 => on

  SW4, SW5-online off

  SW6-online on

  Please notify

  I found the problem!

  It was a twisted spindle.  Straightend out and now it works!

• Can I use a PXI-6224 with the SCB-68 to take the measurements of 4-wire RTD, or do I need a power supply separate?

  I suspect I already know the answer to this question:

  I have an PXI-6224 M-series data acquisition card and a terminal of the SCB-68 block and want to take action using a bunch of 4-wire RTD. Is the power to the power source for these measures 6224, or is - not possible with the hardware I have?

  I know that NEITHER you propose other solutions to my problem: I am interested to know if I can do these measures with the device that I currently have on site.

  Thank you!

  Hello Jeffrey,.

  You have two options here, but it doesn't look like you need some hardware.

  The SMU-4357 built conditioning of signals, but it will not work on the chassis curent you have:

  http://sine.NI.com/NIPs/CDs/view/p/lang/en/NID/210596/

  We also have an option with the NI 9217 cDAQ, but once, it gets you into a different platform:

  http://sine.NI.com/NIPs/CDs/view/p/lang/en/NID/208804

  We used to have an option that we sell no more - the SC-2042RTD. If you are lucky and have one of them on hand so here's some info:

  http://digital.NI.com/public.nsf/allkb/4FF2C0F8D11B99B486256F4C006DCEA0

  You can also use these two elements in conjunction with eachother with your current PXI card:

  http://sine.NI.com/NIPs/CDs/view/p/lang/en/NID/12311

  http://sine.NI.com/NIPs/CDs/view/p/lang/en/NID/10778

  Finally, you could get an SCXI chassis and drop them in:

  http://sine.NI.com/NIPs/CDs/view/p/lang/en/NID/201609

  Thank you

  Joel C

  Technical sales engineer

  National Instruments

• Calendar and the problems of data collection with the DAQ Assistant

  Hello NOR Developer area,

  I am a Novice of LabVIEW and have seen how helpful you all can be, and if I come to ask for your help.

  I'm having some trouble with a VI I built that specifies an input voltage, a SCB - 100 connected to a PCI-6031E and converts this tension in a temperature displayed on a waveform table. The goal is to give a constant reading of the temperature and display it in a chart for as long that the VI is running (and to reset the chart the next time the tracks of VI).

  The problems I've encountered currently are:

  -After a few minutes of the VI running, I get an error message 200279: tried to read samples that are no longer available. The requested sample was already available, but has since been replaced. (to the DAQ Assistant express VI).

  -I don't know how to change my chart so that the minimum value X is both during which the VI was launched and have the maximum X value increases with each iteration of the loop. Currently, I have the VI get the time system and contributing to the property node X scale. This worked for the graph of the voltage, but not for the temperature chart

  I appreciate those of you who took the time to read my post.

  Thank you all for your help.

  Sincerely,

  Ethan A. Klein

  SB candidate in Chemistry & Physics

  Massachusetts Institute of Technology

  Class of 2015

  PS I enclose my VI to give you a better understanding of my current situation.

  E A Klein wrote:

  Thanks for writing.

  What property node is talking?
  I do not understand that many different data types. How can I go on the treatment of all the data?

  (Did you mean I should wire 'blue' data for mathematical functions rather than using the node property tension?)

  Sincerely,

  In fact, one of the nodes property.  I mean specifically the tension property node.  But in reviewing, I noticed the other nodes in property for the chart.  Just set auto-scaling to the X scale and that should take care of two of the nodes property (right click on the graph, X scale-> AutoScale X Scale).  I also recommend placing your mathematical functions in a Subvi to make things easier to read.  Attached, that's what I think you're after.

  I hope that these small tweaks will speed things up enough to avoid your error.  If this isn't the case, then we should begin to look at the design of producer/consumer model or take readings at the same time.  It might also be worth looking away the DAQ Assistant and DAQmx real screws.  But one step at a time.

• Unable to Scan to the computer after downloading macOS Sierra. Is this a software problem?

  How can I scan from HP Envy 4500 to computer after downloading macOS Sierra?

  Hello wdemetris,

  Thanks for asking for scanning helps here in the Apple Support communities. I understand how it is important to have access to your scanner and am happy to offer help for this.

  As a precaution, we always recommend that you have backups to make sure that all your data is safe. You can perform a backup using Time Machine and an external hard drive. Use this article to help make a backup of your Mac: use Time Machine to back up or restore your Mac.

  Then, in accordance with article help: printer and scanner for Sierra, El Capitan, Yosemite, and the Mavericks macOS software, the HP Envy 4500 e-all-in-one is supported for printing and scanning. The drivers must be installed, but if not, if it please go to the App Store and check the updates tab to see if there are updates for HP. If there is, please install.

  If you have only general questions about how to get your updated scanner in place or how to scan pictures, please check out these two articles: macOS Sierra: implement a scanner & macOS Sierra: scan images or documents. If everything is configured correctly and you still have problems scanning, please visit this help article: macOS Sierra: scanning troubleshooting.

  Thanks again and have a great rest of your day.

• My iPhone 6 installed 10.0.2 stops when it gets to 40% of autonomy.  In addition, it seems to pass power WAY to fast with the new software.  Does anyone else have this problem?

  My iPhone 6 installed 10.0.2 stops when it gets to 40% of autonomy.  In addition, it seems to pass power WAY to fast with the new software.  Does anyone else have this problem?

  Hello brooksm549,
  Thank you for using communities of Apple Support.

  I got your message which, since updating your iPhone 6 to iOS 10.0.2 your iPhone stops when it is 40% and the power to empty very quickly. I understand your concern with the iPhone turn off and drains the battery. I recommend you to review the use of the battery to see what app contributes more to the battery drain. The following article will provide you with steps on how to check the use of the battery:

  On the use of the battery on your iPhone, iPad and iPod touch

  When you know about the soft uses more battery, you can change your settings in order to optimize the battery life:

  Maximize the life of the battery and battery life

  Best regards.

• MacBook Pro display problem

  Hello members of the community.

  As of recently, I have noticed some glitches when feeding on my MacBook or awakened from his sleep.

  The colors are distorted, usually with pink, green, or yellow blobs. Blobs cannot entirely replace the colors, they appear to be contained in a element would normally be. For example. the menu bar will be partially pink and white, but pink does not leave the menu bar in this area, and the Office has green lines on it.

  I tried to take a screenshot, but the problem resolves in about 20 seconds, but it's a recurring problem.

  It happens when I wake up, connection or not. I had also certain powers serious and problems of performance, such that my MagSafe LED would not illuminate when plugged on rare occasions, fan could turn unnecessarily, graphics performance were SUPER slow, and the health of my battery was running out quickly. I actually ran a report on the system at 2 different times and my quality of full load is depleting of 1.2% per charge cycle, which is very worrying. I went from 6281 mAh mAh 6138 maximum capacity after two cycles of load. I'm tracking closely it because at this rate, my battery will survive only at load cycles about 150 instead of the 1000 expected, gives me the idea that this could very well be a bad battery. The computer is also warm to the touch while you sleep, not connected to the power supply. I NAP active but even taking into account should not be hotter my iPhone did the same thing.

  I have reset the SMC, and it solved a couple of problems. The charger works fine now and my performance improved considerably (which made me feel better, either it is a high-performance laptop, a 11-inch MacBook Air should not he surpass), and battery life has improved. I feel even if it uses a lot of power in his sleep. Maybe I need to turn off the NAP and see if that makes a difference. The graphic bug still persists however, and I don't have enough time to see if the max battery is depleting again.

  In regards to the bug, is there something that can be done? Basically, I want to assure you that I took all appropriate measures or if someone else has this problem to see if it can be software related instead of my computer.

  I have the entry level MacBook Pro with the retina, last generation.

  Any constructive contribution welcome!

  See you soon.

  -adreaux

  Hello bernardn753,

  After reviewing your post, it seems that you are having problems with the screen showing strange things on it. Looks like you already have a troubleshooting. I recommend you read this article, as reset NVRAM would be to reset your screen resolution settings that should help.

  How to reset the NVRAM on your Mac.

  Thank you for using communities of Apple Support. Good day.

• with IOS 10.0.2 - 5s iphone Bluetooth problems

  Since upgrading ISO 10.0.2 my M50 from PLT Plantronics (helmet unique headset) do not reliably connects with my iPhone 5 more. I have to go to the settings, activate bluetooth turned off/turned on, touch the device on the bluetooth page, etc. Once it connects successfully, it will reconnect (if I turn off the headset and turn it back on) for a short period. The next day he does not connect itself but I play with bluetooth on the iPhone again.

  It has always worked perfectly before the 10th of IOS.

  And, as I noticed others mentioning, the volume is much lower with IOS 10. The maximum volume is much lower. I can barely hear it now, more normal background noise, while driving.

  I did:

  Forget this device for the PLT M50 and paired again (several times)

  I did a Reset Network Settings

  I don't know what else to do - but it's a 10.0.2 IOS issue.

  Hello AppleUser2k,

  Please ask questions about your problems of connection between your iPhone and your Plantronics headset since you upgraded to iOS 10. I understand how important it is to have your Bluetooth devices connect with your iPhone with reliability. Here's what I recommend.

  The first thing we want to make sure is that all your data is safe. You can perform a backup in iCloud or iTunes using this article: backing up your iPhone, iPad, and iPod touch.

  Once your data is safe, try the troubleshooting steps in this article to help: get help to connect a Bluetooth accessory with your iPhone, iPad or iPod touch device should also check with the manufacturer that the device has all the drivers and firmware to work with the new version of iOS.

  If you have checked everything and that you have installed the latest firmware or driver and always are problems, please be aware of your surroundings when you encounter these problems. If you can isolate the time or location, you see the problems, you can isolate the cause. You can even see this help article to ensure that you are not affected by outside interference: the potential sources of Wi-Fi and Bluetooth.

  Thanks again and have a great rest of your day.

• Problem after update 10.0.2 iOS iPhone touchscreen

  After I have updated to iOS 10.0.2, I noticed a problem with the touch screen. Using the position of the image on the right side, near the corner, the toushscreen does not work.
  For example: when you use the keyboard, I can't type the letter 'P', have trouble typing BACKSPACE. Using the Contacts app, I can't scroll through using the alphabet bar.

  Do what idea of the problem?

  Kind regards!

  Hi fabriciorela,

  Thanks for the upgrade to iOS 10! I understand that the right of your screen is unresponsive to the touch. You can try the steps in this link to fix the problem. If the screen of your iPhone, iPad or iPod touch does not respond to touch

  If it does not help the problem, try to restore the device to factory settings. I would like to backup your important data first.

  The backup of your iPhone, iPad and iPod touch

  Use iTunes on your Mac or PC to restore your iPhone, iPad or iPod to factory settings

  Please use the Apple Support communities to post your question. Let us know how it turns out. Have a great day.

• Bluetooth connection problem iPhone - audio system Nissan after upgrade iOS10

  After iOS10.0.2 iOS9 on iPhone upgrade, I got a cordially problem receive calls raise Nissan car audio.

  I can make a call without any problem. Bluetooth connection is stable. I can download address book e.t.c. But I can't receive a call. I see the incoming call on the radio shows. After pressing the button "answer" on the car Audio System, audio between iPhone and Audio streams car breaks down.

  But the cellular connection remains active. I need to rotate the audio output on the screen of the iPhone car for iPhone and back to the car. After that, I can continue my call via the car radio.

  Thanks in advance

  Hello StasV,

  Thank you for using communities Support from Apple. I know having a problem with calls on your iPhone in your car, it's not what you expect. The good news is that these steps will be useful for your problem of phone calls while using the bluetooth in your car. Go to settings > general > accessibility > routing of Audio calls and the value headset/Bluetooth Headset and retest your question.

  Audio routing call - the iPhone user Guide
  Help to connect your iPhone, iPad or iPod touch with your car radio

  See you soon!

• 2 iphones on one iTunes, problem of photo icloud account

  OK, my brother-in-law just updated its OS on his Iphone. He shared an Apple ID with his wife, who has his own iPhone. They all have two backup only in iCloud. His problem is that his wife photos are now on his phone. How can he fix it?

  Get its own identifier Apple- create and start using a Apple - Apple Support ID